LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* AHCI - remove probing of ata2
@ 2007-02-10 14:24 Paul Rolland
  2007-02-10 17:22 ` AHCI - remove probing of ata2 + Jmicron JMB363 ATA mode failing Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-10 14:24 UTC (permalink / raw)
  To: 'Linux Kernel Mailing List'; +Cc: rol

Hello,

I'm using an Asus P5W DH motherboard, with an Intel ICH7 controler, and a 
Jmicron JMB363.

On the Intel, I've connected an IDE HDD and a CD-RW, no problem.
On the SATA side, i've connected 3 SATA disks, but at boot time, the kernel
detects 4 ports, and goes on timeout on ata2 :

...
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
ata1: SATA max UDMA/133 cmd 0xFFFFC200000BC900 ctl 0x0 bmdma 0x0 irq 505
ata2: SATA max UDMA/133 cmd 0xFFFFC200000BC980 ctl 0x0 bmdma 0x0 irq 505
ata3: SATA max UDMA/133 cmd 0xFFFFC200000BCA00 ctl 0x0 bmdma 0x0 irq 505
ata4: SATA max UDMA/133 cmd 0xFFFFC200000BCA80 ctl 0x0 bmdma 0x0 irq 505
scsi0 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: port failed to respond (30 secs, Status 0x80)
ata2: COMRESET failed (device not ready)
ata2: hardreset failed, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA 
ata2.00: ata2: dev 0 multi count 1
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for UDMA/133
...

Is there a way to exclude ata2 from probing ? Nothing is connected, and there
is no associated port on the motherboard...


The second problem is the Jmicron controler. It can act as IDE, SATA, ...
but I've configured it as IDE in the BIOS, and connected a DRD-RW on.
Problem is that IDE driver detects it, as containing ide2 and ide3, and
when probing for the DVD, I've got a lot of timeout on the command.
... But, I'm lost in all the JMICRON configuration possibilities in the 
kernel :
 - it is detected by the IDE driver,
 - it can be activated in ATA/ATAPI/MFM/RLL
 - it can be activated in Serial ATA (prod) and Parallel ATA (experimental)

What should I select ?

Full .config below.

Regards,
Paul


#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.19.1
# Sat Feb 10 14:33:56 2007
#
CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_ZONE_DMA32=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_DMI=y
CONFIG_AUDIT_ARCH=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_TASKSTATS is not set
CONFIG_UTS_NS=y
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_RELAY=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Block layer
#
CONFIG_BLOCK=y
CONFIG_LBD=y
CONFIG_BLK_DEV_IO_TRACE=y
# CONFIG_LSF is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VSMP is not set
# CONFIG_MK8 is not set
CONFIG_MPSC=y
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=128
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_INTERNODE_CACHE_BYTES=128
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_MICROCODE=y
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
CONFIG_X86_HT=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
CONFIG_SMP=y
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_NR_CPUS=8
# CONFIG_HOTPLUG_CPU is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_INTEL=y
# CONFIG_X86_MCE_AMD is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x200000
CONFIG_SECCOMP=y
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_REORDER=y
CONFIG_K8_NB=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ISA_DMA_API=y
CONFIG_GENERIC_PENDING_IRQ=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
# CONFIG_PM_SYSFS_DEPRECATED is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_AC=y
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=y
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=y
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=y
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set

#
# CPUFreq processor drivers
#
# CONFIG_X86_POWERNOW_K8 is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=y
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_ACPI_CPUFREQ=y

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
# CONFIG_X86_SPEEDSTEP_LIB is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y

#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=y
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_NET_KEY=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=y
CONFIG_NET_IPGRE=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
CONFIG_INET_IPCOMP=y
CONFIG_INET_XFRM_TUNNEL=y
CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"

#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
CONFIG_IPV6=y
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
CONFIG_INET6_AH=y
CONFIG_INET6_ESP=y
CONFIG_INET6_IPCOMP=y
# CONFIG_IPV6_MIP6 is not set
CONFIG_INET6_XFRM_TUNNEL=y
CONFIG_INET6_TUNNEL=y
CONFIG_INET6_XFRM_MODE_TRANSPORT=y
CONFIG_INET6_XFRM_MODE_TUNNEL=y
CONFIG_INET6_XFRM_MODE_BEET=y
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=y
CONFIG_IPV6_TUNNEL=y
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=y
CONFIG_NETFILTER_NETLINK_QUEUE=y
CONFIG_NETFILTER_NETLINK_LOG=y
# CONFIG_NETFILTER_XTABLES is not set

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=y
CONFIG_IP_NF_CT_ACCT=y
CONFIG_IP_NF_CONNTRACK_MARK=y
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
CONFIG_IP_NF_CONNTRACK_NETLINK=y
CONFIG_IP_NF_CT_PROTO_SCTP=y
CONFIG_IP_NF_FTP=y
CONFIG_IP_NF_IRC=y
CONFIG_IP_NF_NETBIOS_NS=y
CONFIG_IP_NF_TFTP=y
CONFIG_IP_NF_AMANDA=y
CONFIG_IP_NF_PPTP=y
# CONFIG_IP_NF_H323 is not set
# CONFIG_IP_NF_SIP is not set
CONFIG_IP_NF_QUEUE=y

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_IP6_NF_QUEUE=y

#
# Bridge: Netfilter Configuration
#
# CONFIG_BRIDGE_NF_EBTABLES is not set

#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set

#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=y
CONFIG_VLAN_8021Q=y
# CONFIG_DECNET is not set
CONFIG_LLC=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CLK_JIFFIES=y
# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
# CONFIG_NET_SCH_CLK_CPU is not set

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=y
CONFIG_NET_SCH_HTB=y
CONFIG_NET_SCH_HFSC=y
CONFIG_NET_SCH_PRIO=y
CONFIG_NET_SCH_RED=y
CONFIG_NET_SCH_SFQ=y
CONFIG_NET_SCH_TEQL=y
CONFIG_NET_SCH_TBF=y
CONFIG_NET_SCH_GRED=y
CONFIG_NET_SCH_DSMARK=y
CONFIG_NET_SCH_NETEM=y
CONFIG_NET_SCH_INGRESS=y

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=y
CONFIG_NET_CLS_TCINDEX=y
CONFIG_NET_CLS_ROUTE4=y
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=y
CONFIG_NET_CLS_U32=y
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=y
CONFIG_NET_CLS_RSVP6=y
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=y
CONFIG_NET_EMATCH_NBYTE=y
CONFIG_NET_EMATCH_U32=y
CONFIG_NET_EMATCH_META=y
CONFIG_NET_EMATCH_TEXT=y
# CONFIG_NET_CLS_ACT is not set
CONFIG_NET_CLS_POLICE=y
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_ESTIMATOR=y

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
CONFIG_WIRELESS_EXT=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_SYS_HYPERVISOR is not set

#
# Connector - unified userspace <-> kernelspace linker
#
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
# CONFIG_PARPORT is not set

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y

#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=y
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
# CONFIG_ATA_OVER_ETH is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_IDE_TASK_IOCTL=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y

#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set

#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set

#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
#
CONFIG_ATA=y
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
CONFIG_SATA_INTEL_COMBINED=y
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID456 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
# CONFIG_BLK_DEV_DM is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set

#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=y

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
CONFIG_IEEE1394_OUI_DB=y
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set

#
# Device Drivers
#

#
# Texas Instruments PCILynx requires I2C
#
CONFIG_IEEE1394_OHCI1394=y

#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=y
CONFIG_IEEE1394_SBP2=y
# CONFIG_IEEE1394_ETH1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
CONFIG_IEEE1394_RAWIO=y

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
CONFIG_EQUALIZER=y
CONFIG_TUN=y
# CONFIG_NET_SB1000 is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set


#
# PHY device support
#

#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
CONFIG_SKY2=y
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
# CONFIG_NET_WIRELESS_RTNETLINK is not set

#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set

#
# Wireless 802.11b ISA/PCI cards support
#
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set

#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_PRISM54 is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_HOSTAP is not set
CONFIG_NET_WIRELESS=y

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=y
CONFIG_PPP_SYNC_TTY=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
CONFIG_PPP_MPPE=y
# CONFIG_PPPOE is not set
# CONFIG_SLIP is not set
CONFIG_SLHC=y
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_UINPUT is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_NR_UARTS=48
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=y
# CONFIG_HW_RANDOM_AMD is not set
# CONFIG_HW_RANDOM_GEODE is not set
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=y

#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set

#
# I2C support
#
# CONFIG_I2C is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
# CONFIG_HWMON_VID is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
# CONFIG_USB_DABUSB is not set

#
# Graphics support
#
CONFIG_FIRMWARE_EDID=y
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=y
CONFIG_FB_VESA=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
# CONFIG_LOGO is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Sound
#
CONFIG_SOUND=y

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_SEQ_DUMMY=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_AC97_CODEC=y
CONFIG_SND_AC97_BUS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
CONFIG_SND_HDA_INTEL=y
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AC97_POWER_SAVE is not set

#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_TOUCHSCREEN is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_ATI_REMOTE2 is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y

#
# USB port drivers
#

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_TEST is not set

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
# CONFIG_MMC is not set

#
# LED devices
#
# CONFIG_NEW_LEDS is not set

#
# LED drivers
#

#
# LED Triggers
#

#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set

#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
# CONFIG_EDAC is not set

#
# Real Time Clock
#
# CONFIG_RTC_CLASS is not set

#
# DMA Engine support
#
# CONFIG_DMA_ENGINE is not set

#
# DMA Clients
#

#
# DMA Devices
#

#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
CONFIG_QFMT_V1=y
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
CONFIG_FUSE_FS=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_ECRYPT_FS=y
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_SMB_FS=y
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_CIFS=y
CONFIG_CIFS_STATS=y
CONFIG_CIFS_STATS2=y
# CONFIG_CIFS_WEAK_PW_HASH is not set
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=y
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y

#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
CONFIG_KPROBES=y

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHEDSTATS=y
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_UNWIND_INFO is not set
CONFIG_FORCED_INLINING=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
# CONFIG_DEBUG_RODATA is not set
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set

#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABILITIES=y
CONFIG_SECURITY_ROOTPLUG=y

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_WP512=y
CONFIG_CRYPTO_TGR192=y
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_BLOWFISH=y
# CONFIG_CRYPTO_TWOFISH is not set
CONFIG_CRYPTO_TWOFISH_COMMON=y
CONFIG_CRYPTO_TWOFISH_X86_64=y
CONFIG_CRYPTO_SERPENT=y
# CONFIG_CRYPTO_AES is not set
CONFIG_CRYPTO_AES_X86_64=y
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
CONFIG_CRYPTO_TEA=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_KHAZAD=y
CONFIG_CRYPTO_ANUBIS=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_CRYPTO_CRC32C=y
# CONFIG_CRYPTO_TEST is not set

#
# Hardware crypto devices
#

#
# Library routines
#
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=y
CONFIG_TEXTSEARCH_BM=y
CONFIG_TEXTSEARCH_FSM=y
CONFIG_PLIST=y


^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2 + Jmicron JMB363 ATA mode failing
  2007-02-10 14:24 AHCI - remove probing of ata2 Paul Rolland
@ 2007-02-10 17:22 ` Paul Rolland
  0 siblings, 0 replies; 18+ messages in thread
From: Paul Rolland @ 2007-02-10 17:22 UTC (permalink / raw)
  To: rol, 'Linux Kernel Mailing List'

Some more messages, using 2.6.20 :
 - ICH7 from ATA/ATAPI/MFM/RLL support,
 - Jmicron from ATA/ATAPI/MFM/RLL support,
 - SATA AHCI from Serial ATA (prod)

Boot goes to :

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 6L200P0, ATA DISK drive
hdb: ASUS CRW-5232A3, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
JMB363: IDE controller at PCI slot 0000:02:00.0
PCI: Device 0000:02:00.0 not available because of resource collisions
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
JMB363: BIOS configuration fixed.
JMB363: chipset revision 2
JMB363: 100% native mode on irq 17
JMB363: port 0x01f0 already claimed by ide0
JMB363: port 0x0170 already claimed by ide1
JMB363: neither IDE port enabled (BIOS)
JMB363: IDE controller at PCI slot 0000:02:00.1
PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 16 (level, low) -> IRQ 16
JMB363: chipset revision 2
JMB363: 100% native mode on irq 16
    ide2: BM-DMA at 0x9400-0x9407, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0x9408-0x940f, BIOS settings: hdg:pio, hdh:pio
hde: ASUS DRW-1608P, ATAPI CD/DVD-ROM drive
ide2 at 0x9c00-0x9c07,0x9882 on irq 16
hda: max request size: 512KiB
hda: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-cd: cmd 0x5a timed out
hde: lost interrupt
ide-cd: cmd 0x5a timed out
hde: lost interrupt
hde: packet command error: status=0x51 { DriveReady SeekComplete Error }
hde: packet command error: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
ide-cd: cmd 0x3 timed out
hde: lost interrupt
hde: request sense failure: status=0x51 { DriveReady SeekComplete Error }
hde: request sense failure: error=0x40 { LastFailedSense=0x04 }

and then the machine is locked, no keyboard, but the DVD-ROM is correctly
detected, as the message :
hde: ASUS DRW-1608P, ATAPI CD/DVD-ROM drive
indicates.

If I remove Jmicron support from the kernel, I have ICH7 in ATA/ATAPI/...
and AHCI in Serial ATA, and the boot process is nearly fine, except the
ata2 timeout, that I can't prevent even with ata2=noprobe in the command line
:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 6L200P0, ATA DISK drive
hdb: ASUS CRW-5232A3, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
ata1: SATA max UDMA/133 cmd 0xFFFFC20000054900 ctl 0x0 bmdma 0x0 irq 1272
ata2: SATA max UDMA/133 cmd 0xFFFFC20000054980 ctl 0x0 bmdma 0x0 irq 1272
ata3: SATA max UDMA/133 cmd 0xFFFFC20000054A00 ctl 0x0 bmdma 0x0 irq 1272
ata4: SATA max UDMA/133 cmd 0xFFFFC20000054A80 ctl 0x0 bmdma 0x0 irq 1272
scsi0 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: port failed to respond (30 secs, Status 0x80)
ata2: COMRESET failed (device not ready)
ata2: hardreset failed, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA 
ata2.00: ata2: dev 0 multi count 1
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for UDMA/133

The specification summary of the board says :
Intel ICH7R Southbridge supports
 - 1 x Ultra DMA 100/66/33
 - 3 x Serial ATA 3.0 Gb/s devices, with raid 0, 1, 5
 - Intel Matrix Storage
Jmicron JMB363 Serial Ata controller supports :
 - 1 x External Sata 3.0 Gb/s (SATA-on-the-Go)
 - 1 x Internel Sata 3.0 Gb/s 
 - 1 x Internel DMA 100/66/33 connector for two devices

Regards,
Paul

Paul Rolland, rol(at)as2917.net
ex-AS2917 Network administrator and Peering Coordinator

--

Please no HTML, I'm not a browser - Pas d'HTML, je ne suis pas un navigateur 
"Some people dream of success... while others wake up and work hard at it" 

"I worry about my child and the Internet all the time, even though she's too 
young to have logged on yet. Here's what I worry about. I worry that 10 or 15 
years from now, she will come to me and say 'Daddy, where were you when they 
took freedom of the press away from the Internet?'"
--Mike Godwin, Electronic Frontier Foundation 
  

> -----Original Message-----
> From: linux-kernel-owner@vger.kernel.org 
> [mailto:linux-kernel-owner@vger.kernel.org] On Behalf Of Paul Rolland
> Sent: Saturday, February 10, 2007 3:24 PM
> To: 'Linux Kernel Mailing List'
> Cc: rol@as2917.net
> Subject: AHCI - remove probing of ata2
> 
> Hello,
> 
> I'm using an Asus P5W DH motherboard, with an Intel ICH7 
> controler, and a 
> Jmicron JMB363.
> 
> On the Intel, I've connected an IDE HDD and a CD-RW, no problem.
> On the SATA side, i've connected 3 SATA disks, but at boot 
> time, the kernel
> detects 4 ports, and goes on timeout on ata2 :
> 
> ...
> ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf 
> impl SATA mode
> ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
> ata1: SATA max UDMA/133 cmd 0xFFFFC200000BC900 ctl 0x0 bmdma 
> 0x0 irq 505
> ata2: SATA max UDMA/133 cmd 0xFFFFC200000BC980 ctl 0x0 bmdma 
> 0x0 irq 505
> ata3: SATA max UDMA/133 cmd 0xFFFFC200000BCA00 ctl 0x0 bmdma 
> 0x0 irq 505
> ata4: SATA max UDMA/133 cmd 0xFFFFC200000BCA80 ctl 0x0 bmdma 
> 0x0 irq 505
> scsi0 : ahci
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ 
> (depth 31/32)
> ata1.00: ata1: dev 0 multi count 0
> ata1.00: configured for UDMA/133
> scsi1 : ahci
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: qc timeout (cmd 0xec)
> ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
> ata2: port is slow to respond, please be patient (Status 0x80)
> ata2: port failed to respond (30 secs, Status 0x80)
> ata2: COMRESET failed (device not ready)
> ata2: hardreset failed, retrying in 5 secs
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA 
> ata2.00: ata2: dev 0 multi count 1
> ata2.00: configured for UDMA/133
> scsi2 : ahci
> ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ 
> (depth 31/32)
> ata3.00: ata3: dev 0 multi count 0
> ata3.00: configured for UDMA/133
> ...
> 
> Is there a way to exclude ata2 from probing ? Nothing is 
> connected, and there
> is no associated port on the motherboard...
> 
> 
> The second problem is the Jmicron controler. It can act as 
> IDE, SATA, ...
> but I've configured it as IDE in the BIOS, and connected a DRD-RW on.
> Problem is that IDE driver detects it, as containing ide2 and 
> ide3, and
> when probing for the DVD, I've got a lot of timeout on the command.
> ... But, I'm lost in all the JMICRON configuration 
> possibilities in the 
> kernel :
>  - it is detected by the IDE driver,
>  - it can be activated in ATA/ATAPI/MFM/RLL
>  - it can be activated in Serial ATA (prod) and Parallel ATA 
> (experimental)
> 
> What should I select ?
> 
> Full .config below.
> 
> Regards,
> Paul
> 
> 
> #
> # Automatically generated make config: don't edit
> # Linux kernel version: 2.6.19.1
> # Sat Feb 10 14:33:56 2007
> #
> CONFIG_X86_64=y
> CONFIG_64BIT=y
> CONFIG_X86=y
> CONFIG_ZONE_DMA32=y
> CONFIG_LOCKDEP_SUPPORT=y
> CONFIG_STACKTRACE_SUPPORT=y
> CONFIG_SEMAPHORE_SLEEPERS=y
> CONFIG_MMU=y
> CONFIG_RWSEM_GENERIC_SPINLOCK=y
> CONFIG_GENERIC_HWEIGHT=y
> CONFIG_GENERIC_CALIBRATE_DELAY=y
> CONFIG_X86_CMPXCHG=y
> CONFIG_EARLY_PRINTK=y
> CONFIG_GENERIC_ISA_DMA=y
> CONFIG_GENERIC_IOMAP=y
> CONFIG_ARCH_MAY_HAVE_PC_FDC=y
> CONFIG_ARCH_POPULATES_NODE_MAP=y
> CONFIG_DMI=y
> CONFIG_AUDIT_ARCH=y
> CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
> 
> #
> # Code maturity level options
> #
> CONFIG_EXPERIMENTAL=y
> CONFIG_LOCK_KERNEL=y
> CONFIG_INIT_ENV_ARG_LIMIT=32
> 
> #
> # General setup
> #
> CONFIG_LOCALVERSION=""
> # CONFIG_LOCALVERSION_AUTO is not set
> CONFIG_SWAP=y
> CONFIG_SYSVIPC=y
> # CONFIG_IPC_NS is not set
> CONFIG_POSIX_MQUEUE=y
> CONFIG_BSD_PROCESS_ACCT=y
> CONFIG_BSD_PROCESS_ACCT_V3=y
> # CONFIG_TASKSTATS is not set
> CONFIG_UTS_NS=y
> # CONFIG_AUDIT is not set
> CONFIG_IKCONFIG=y
> CONFIG_IKCONFIG_PROC=y
> # CONFIG_CPUSETS is not set
> CONFIG_RELAY=y
> CONFIG_INITRAMFS_SOURCE=""
> # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
> CONFIG_SYSCTL=y
> # CONFIG_EMBEDDED is not set
> CONFIG_UID16=y
> CONFIG_SYSCTL_SYSCALL=y
> CONFIG_KALLSYMS=y
> CONFIG_KALLSYMS_ALL=y
> CONFIG_KALLSYMS_EXTRA_PASS=y
> CONFIG_HOTPLUG=y
> CONFIG_PRINTK=y
> CONFIG_BUG=y
> CONFIG_ELF_CORE=y
> CONFIG_BASE_FULL=y
> CONFIG_FUTEX=y
> CONFIG_EPOLL=y
> CONFIG_SHMEM=y
> CONFIG_SLAB=y
> CONFIG_VM_EVENT_COUNTERS=y
> CONFIG_RT_MUTEXES=y
> # CONFIG_TINY_SHMEM is not set
> CONFIG_BASE_SMALL=0
> # CONFIG_SLOB is not set
> 
> #
> # Loadable module support
> #
> CONFIG_MODULES=y
> CONFIG_MODULE_UNLOAD=y
> # CONFIG_MODULE_FORCE_UNLOAD is not set
> CONFIG_MODVERSIONS=y
> CONFIG_MODULE_SRCVERSION_ALL=y
> CONFIG_KMOD=y
> CONFIG_STOP_MACHINE=y
> 
> #
> # Block layer
> #
> CONFIG_BLOCK=y
> CONFIG_LBD=y
> CONFIG_BLK_DEV_IO_TRACE=y
> # CONFIG_LSF is not set
> 
> #
> # IO Schedulers
> #
> CONFIG_IOSCHED_NOOP=y
> CONFIG_IOSCHED_AS=y
> CONFIG_IOSCHED_DEADLINE=y
> CONFIG_IOSCHED_CFQ=y
> CONFIG_DEFAULT_AS=y
> # CONFIG_DEFAULT_DEADLINE is not set
> # CONFIG_DEFAULT_CFQ is not set
> # CONFIG_DEFAULT_NOOP is not set
> CONFIG_DEFAULT_IOSCHED="anticipatory"
> 
> #
> # Processor type and features
> #
> CONFIG_X86_PC=y
> # CONFIG_X86_VSMP is not set
> # CONFIG_MK8 is not set
> CONFIG_MPSC=y
> # CONFIG_GENERIC_CPU is not set
> CONFIG_X86_L1_CACHE_BYTES=128
> CONFIG_X86_L1_CACHE_SHIFT=7
> CONFIG_X86_INTERNODE_CACHE_BYTES=128
> CONFIG_X86_TSC=y
> CONFIG_X86_GOOD_APIC=y
> CONFIG_MICROCODE=y
> CONFIG_MICROCODE_OLD_INTERFACE=y
> CONFIG_X86_MSR=y
> CONFIG_X86_CPUID=y
> CONFIG_X86_HT=y
> CONFIG_X86_IO_APIC=y
> CONFIG_X86_LOCAL_APIC=y
> CONFIG_MTRR=y
> CONFIG_SMP=y
> CONFIG_SCHED_SMT=y
> CONFIG_SCHED_MC=y
> # CONFIG_PREEMPT_NONE is not set
> # CONFIG_PREEMPT_VOLUNTARY is not set
> CONFIG_PREEMPT=y
> CONFIG_PREEMPT_BKL=y
> # CONFIG_NUMA is not set
> CONFIG_ARCH_SPARSEMEM_ENABLE=y
> CONFIG_ARCH_FLATMEM_ENABLE=y
> CONFIG_SELECT_MEMORY_MODEL=y
> CONFIG_FLATMEM_MANUAL=y
> # CONFIG_DISCONTIGMEM_MANUAL is not set
> # CONFIG_SPARSEMEM_MANUAL is not set
> CONFIG_FLATMEM=y
> CONFIG_FLAT_NODE_MEM_MAP=y
> # CONFIG_SPARSEMEM_STATIC is not set
> CONFIG_SPLIT_PTLOCK_CPUS=4
> CONFIG_RESOURCES_64BIT=y
> CONFIG_NR_CPUS=8
> # CONFIG_HOTPLUG_CPU is not set
> CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
> CONFIG_HPET_TIMER=y
> CONFIG_HPET_EMULATE_RTC=y
> CONFIG_IOMMU=y
> # CONFIG_CALGARY_IOMMU is not set
> CONFIG_SWIOTLB=y
> CONFIG_X86_MCE=y
> CONFIG_X86_MCE_INTEL=y
> # CONFIG_X86_MCE_AMD is not set
> # CONFIG_KEXEC is not set
> # CONFIG_CRASH_DUMP is not set
> CONFIG_PHYSICAL_START=0x200000
> CONFIG_SECCOMP=y
> # CONFIG_CC_STACKPROTECTOR is not set
> # CONFIG_HZ_100 is not set
> CONFIG_HZ_250=y
> # CONFIG_HZ_1000 is not set
> CONFIG_HZ=250
> CONFIG_REORDER=y
> CONFIG_K8_NB=y
> CONFIG_GENERIC_HARDIRQS=y
> CONFIG_GENERIC_IRQ_PROBE=y
> CONFIG_ISA_DMA_API=y
> CONFIG_GENERIC_PENDING_IRQ=y
> 
> #
> # Power management options
> #
> CONFIG_PM=y
> CONFIG_PM_LEGACY=y
> # CONFIG_PM_DEBUG is not set
> # CONFIG_PM_SYSFS_DEPRECATED is not set
> 
> #
> # ACPI (Advanced Configuration and Power Interface) Support
> #
> CONFIG_ACPI=y
> CONFIG_ACPI_AC=y
> # CONFIG_ACPI_BATTERY is not set
> CONFIG_ACPI_BUTTON=y
> CONFIG_ACPI_VIDEO=y
> # CONFIG_ACPI_HOTKEY is not set
> CONFIG_ACPI_FAN=y
> # CONFIG_ACPI_DOCK is not set
> CONFIG_ACPI_PROCESSOR=y
> CONFIG_ACPI_THERMAL=y
> # CONFIG_ACPI_ASUS is not set
> # CONFIG_ACPI_IBM is not set
> # CONFIG_ACPI_TOSHIBA is not set
> CONFIG_ACPI_BLACKLIST_YEAR=0
> # CONFIG_ACPI_DEBUG is not set
> CONFIG_ACPI_EC=y
> CONFIG_ACPI_POWER=y
> CONFIG_ACPI_SYSTEM=y
> CONFIG_X86_PM_TIMER=y
> CONFIG_ACPI_CONTAINER=y
> 
> #
> # CPU Frequency scaling
> #
> CONFIG_CPU_FREQ=y
> CONFIG_CPU_FREQ_TABLE=y
> # CONFIG_CPU_FREQ_DEBUG is not set
> CONFIG_CPU_FREQ_STAT=y
> CONFIG_CPU_FREQ_STAT_DETAILS=y
> CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
> # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
> CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
> # CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
> # CONFIG_CPU_FREQ_GOV_USERSPACE is not set
> # CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
> # CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
> 
> #
> # CPUFreq processor drivers
> #
> # CONFIG_X86_POWERNOW_K8 is not set
> CONFIG_X86_SPEEDSTEP_CENTRINO=y
> CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
> CONFIG_X86_ACPI_CPUFREQ=y
> 
> #
> # shared options
> #
> # CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
> # CONFIG_X86_SPEEDSTEP_LIB is not set
> 
> #
> # Bus options (PCI etc.)
> #
> CONFIG_PCI=y
> CONFIG_PCI_DIRECT=y
> CONFIG_PCI_MMCONFIG=y
> CONFIG_PCIEPORTBUS=y
> CONFIG_PCIEAER=y
> CONFIG_PCI_MSI=y
> # CONFIG_PCI_DEBUG is not set
> CONFIG_HT_IRQ=y
> 
> #
> # PCCARD (PCMCIA/CardBus) support
> #
> # CONFIG_PCCARD is not set
> 
> #
> # PCI Hotplug Support
> #
> # CONFIG_HOTPLUG_PCI is not set
> 
> #
> # Executable file formats / Emulations
> #
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=y
> CONFIG_IA32_EMULATION=y
> CONFIG_IA32_AOUT=y
> CONFIG_COMPAT=y
> CONFIG_SYSVIPC_COMPAT=y
> 
> #
> # Networking
> #
> CONFIG_NET=y
> 
> #
> # Networking options
> #
> # CONFIG_NETDEBUG is not set
> CONFIG_PACKET=y
> CONFIG_PACKET_MMAP=y
> CONFIG_UNIX=y
> CONFIG_XFRM=y
> CONFIG_XFRM_USER=y
> # CONFIG_XFRM_SUB_POLICY is not set
> CONFIG_NET_KEY=y
> CONFIG_INET=y
> # CONFIG_IP_MULTICAST is not set
> # CONFIG_IP_ADVANCED_ROUTER is not set
> CONFIG_IP_FIB_HASH=y
> # CONFIG_IP_PNP is not set
> CONFIG_NET_IPIP=y
> CONFIG_NET_IPGRE=y
> # CONFIG_ARPD is not set
> CONFIG_SYN_COOKIES=y
> CONFIG_INET_AH=y
> CONFIG_INET_ESP=y
> CONFIG_INET_IPCOMP=y
> CONFIG_INET_XFRM_TUNNEL=y
> CONFIG_INET_TUNNEL=y
> CONFIG_INET_XFRM_MODE_TRANSPORT=y
> CONFIG_INET_XFRM_MODE_TUNNEL=y
> CONFIG_INET_XFRM_MODE_BEET=y
> CONFIG_INET_DIAG=y
> CONFIG_INET_TCP_DIAG=y
> # CONFIG_TCP_CONG_ADVANCED is not set
> CONFIG_TCP_CONG_CUBIC=y
> CONFIG_DEFAULT_TCP_CONG="cubic"
> 
> #
> # IP: Virtual Server Configuration
> #
> # CONFIG_IP_VS is not set
> CONFIG_IPV6=y
> CONFIG_IPV6_PRIVACY=y
> # CONFIG_IPV6_ROUTER_PREF is not set
> CONFIG_INET6_AH=y
> CONFIG_INET6_ESP=y
> CONFIG_INET6_IPCOMP=y
> # CONFIG_IPV6_MIP6 is not set
> CONFIG_INET6_XFRM_TUNNEL=y
> CONFIG_INET6_TUNNEL=y
> CONFIG_INET6_XFRM_MODE_TRANSPORT=y
> CONFIG_INET6_XFRM_MODE_TUNNEL=y
> CONFIG_INET6_XFRM_MODE_BEET=y
> # CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
> CONFIG_IPV6_SIT=y
> CONFIG_IPV6_TUNNEL=y
> # CONFIG_IPV6_MULTIPLE_TABLES is not set
> # CONFIG_NETLABEL is not set
> # CONFIG_NETWORK_SECMARK is not set
> CONFIG_NETFILTER=y
> # CONFIG_NETFILTER_DEBUG is not set
> CONFIG_BRIDGE_NETFILTER=y
> 
> #
> # Core Netfilter Configuration
> #
> CONFIG_NETFILTER_NETLINK=y
> CONFIG_NETFILTER_NETLINK_QUEUE=y
> CONFIG_NETFILTER_NETLINK_LOG=y
> # CONFIG_NETFILTER_XTABLES is not set
> 
> #
> # IP: Netfilter Configuration
> #
> CONFIG_IP_NF_CONNTRACK=y
> CONFIG_IP_NF_CT_ACCT=y
> CONFIG_IP_NF_CONNTRACK_MARK=y
> # CONFIG_IP_NF_CONNTRACK_EVENTS is not set
> CONFIG_IP_NF_CONNTRACK_NETLINK=y
> CONFIG_IP_NF_CT_PROTO_SCTP=y
> CONFIG_IP_NF_FTP=y
> CONFIG_IP_NF_IRC=y
> CONFIG_IP_NF_NETBIOS_NS=y
> CONFIG_IP_NF_TFTP=y
> CONFIG_IP_NF_AMANDA=y
> CONFIG_IP_NF_PPTP=y
> # CONFIG_IP_NF_H323 is not set
> # CONFIG_IP_NF_SIP is not set
> CONFIG_IP_NF_QUEUE=y
> 
> #
> # IPv6: Netfilter Configuration (EXPERIMENTAL)
> #
> CONFIG_IP6_NF_QUEUE=y
> 
> #
> # Bridge: Netfilter Configuration
> #
> # CONFIG_BRIDGE_NF_EBTABLES is not set
> 
> #
> # DCCP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_DCCP is not set
> 
> #
> # SCTP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_SCTP is not set
> 
> #
> # TIPC Configuration (EXPERIMENTAL)
> #
> # CONFIG_TIPC is not set
> # CONFIG_ATM is not set
> CONFIG_BRIDGE=y
> CONFIG_VLAN_8021Q=y
> # CONFIG_DECNET is not set
> CONFIG_LLC=y
> # CONFIG_LLC2 is not set
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
> # CONFIG_X25 is not set
> # CONFIG_LAPB is not set
> # CONFIG_ECONET is not set
> # CONFIG_WAN_ROUTER is not set
> 
> #
> # QoS and/or fair queueing
> #
> CONFIG_NET_SCHED=y
> CONFIG_NET_SCH_CLK_JIFFIES=y
> # CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
> # CONFIG_NET_SCH_CLK_CPU is not set
> 
> #
> # Queueing/Scheduling
> #
> CONFIG_NET_SCH_CBQ=y
> CONFIG_NET_SCH_HTB=y
> CONFIG_NET_SCH_HFSC=y
> CONFIG_NET_SCH_PRIO=y
> CONFIG_NET_SCH_RED=y
> CONFIG_NET_SCH_SFQ=y
> CONFIG_NET_SCH_TEQL=y
> CONFIG_NET_SCH_TBF=y
> CONFIG_NET_SCH_GRED=y
> CONFIG_NET_SCH_DSMARK=y
> CONFIG_NET_SCH_NETEM=y
> CONFIG_NET_SCH_INGRESS=y
> 
> #
> # Classification
> #
> CONFIG_NET_CLS=y
> CONFIG_NET_CLS_BASIC=y
> CONFIG_NET_CLS_TCINDEX=y
> CONFIG_NET_CLS_ROUTE4=y
> CONFIG_NET_CLS_ROUTE=y
> CONFIG_NET_CLS_FW=y
> CONFIG_NET_CLS_U32=y
> CONFIG_CLS_U32_PERF=y
> CONFIG_CLS_U32_MARK=y
> CONFIG_NET_CLS_RSVP=y
> CONFIG_NET_CLS_RSVP6=y
> CONFIG_NET_EMATCH=y
> CONFIG_NET_EMATCH_STACK=32
> CONFIG_NET_EMATCH_CMP=y
> CONFIG_NET_EMATCH_NBYTE=y
> CONFIG_NET_EMATCH_U32=y
> CONFIG_NET_EMATCH_META=y
> CONFIG_NET_EMATCH_TEXT=y
> # CONFIG_NET_CLS_ACT is not set
> CONFIG_NET_CLS_POLICE=y
> # CONFIG_NET_CLS_IND is not set
> CONFIG_NET_ESTIMATOR=y
> 
> #
> # Network testing
> #
> # CONFIG_NET_PKTGEN is not set
> # CONFIG_NET_TCPPROBE is not set
> # CONFIG_HAMRADIO is not set
> # CONFIG_IRDA is not set
> # CONFIG_BT is not set
> # CONFIG_IEEE80211 is not set
> CONFIG_WIRELESS_EXT=y
> 
> #
> # Device Drivers
> #
> 
> #
> # Generic Driver Options
> #
> CONFIG_STANDALONE=y
> CONFIG_PREVENT_FIRMWARE_BUILD=y
> CONFIG_FW_LOADER=y
> # CONFIG_DEBUG_DRIVER is not set
> # CONFIG_SYS_HYPERVISOR is not set
> 
> #
> # Connector - unified userspace <-> kernelspace linker
> #
> CONFIG_CONNECTOR=y
> CONFIG_PROC_EVENTS=y
> 
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
> 
> #
> # Parallel port support
> #
> # CONFIG_PARPORT is not set
> 
> #
> # Plug and Play support
> #
> CONFIG_PNP=y
> # CONFIG_PNP_DEBUG is not set
> 
> #
> # Protocols
> #
> CONFIG_PNPACPI=y
> 
> #
> # Block devices
> #
> CONFIG_BLK_DEV_FD=y
> # CONFIG_BLK_CPQ_DA is not set
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> # CONFIG_BLK_DEV_UMEM is not set
> # CONFIG_BLK_DEV_COW_COMMON is not set
> CONFIG_BLK_DEV_LOOP=y
> CONFIG_BLK_DEV_CRYPTOLOOP=y
> CONFIG_BLK_DEV_NBD=y
> # CONFIG_BLK_DEV_SX8 is not set
> # CONFIG_BLK_DEV_UB is not set
> CONFIG_BLK_DEV_RAM=y
> CONFIG_BLK_DEV_RAM_COUNT=16
> CONFIG_BLK_DEV_RAM_SIZE=65536
> CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
> CONFIG_BLK_DEV_INITRD=y
> CONFIG_CDROM_PKTCDVD=y
> CONFIG_CDROM_PKTCDVD_BUFFERS=8
> # CONFIG_CDROM_PKTCDVD_WCACHE is not set
> # CONFIG_ATA_OVER_ETH is not set
> 
> #
> # Misc devices
> #
> # CONFIG_IBM_ASM is not set
> # CONFIG_SGI_IOC4 is not set
> # CONFIG_TIFM_CORE is not set
> 
> #
> # ATA/ATAPI/MFM/RLL support
> #
> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y
> 
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_IDE_SATA is not set
> # CONFIG_BLK_DEV_HD_IDE is not set
> CONFIG_BLK_DEV_IDEDISK=y
> # CONFIG_IDEDISK_MULTI_MODE is not set
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> CONFIG_BLK_DEV_IDEFLOPPY=y
> CONFIG_BLK_DEV_IDESCSI=y
> CONFIG_IDE_TASK_IOCTL=y
> 
> #
> # IDE chipset support/bugfixes
> #
> CONFIG_IDE_GENERIC=y
> # CONFIG_BLK_DEV_CMD640 is not set
> # CONFIG_BLK_DEV_IDEPNP is not set
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> CONFIG_BLK_DEV_GENERIC=y
> # CONFIG_BLK_DEV_OPTI621 is not set
> # CONFIG_BLK_DEV_RZ1000 is not set
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
> CONFIG_IDEDMA_PCI_AUTO=y
> # CONFIG_IDEDMA_ONLYDISK is not set
> # CONFIG_BLK_DEV_AEC62XX is not set
> # CONFIG_BLK_DEV_ALI15X3 is not set
> # CONFIG_BLK_DEV_AMD74XX is not set
> # CONFIG_BLK_DEV_ATIIXP is not set
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_TRIFLEX is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5520 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> # CONFIG_BLK_DEV_JMICRON is not set
> # CONFIG_BLK_DEV_SC1200 is not set
> CONFIG_BLK_DEV_PIIX=y
> # CONFIG_BLK_DEV_IT821X is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_PDC202XX_OLD is not set
> # CONFIG_BLK_DEV_PDC202XX_NEW is not set
> # CONFIG_BLK_DEV_SVWKS is not set
> # CONFIG_BLK_DEV_SIIMAGE is not set
> # CONFIG_BLK_DEV_SIS5513 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_VIA82CXXX is not set
> # CONFIG_IDE_ARM is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_IDEDMA_IVB is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_BLK_DEV_HD is not set
> 
> #
> # SCSI device support
> #
> # CONFIG_RAID_ATTRS is not set
> CONFIG_SCSI=y
> # CONFIG_SCSI_NETLINK is not set
> CONFIG_SCSI_PROC_FS=y
> 
> #
> # SCSI support type (disk, tape, CD-ROM)
> #
> CONFIG_BLK_DEV_SD=y
> # CONFIG_CHR_DEV_ST is not set
> # CONFIG_CHR_DEV_OSST is not set
> CONFIG_BLK_DEV_SR=y
> # CONFIG_BLK_DEV_SR_VENDOR is not set
> CONFIG_CHR_DEV_SG=y
> # CONFIG_CHR_DEV_SCH is not set
> 
> #
> # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
> #
> CONFIG_SCSI_MULTI_LUN=y
> CONFIG_SCSI_CONSTANTS=y
> CONFIG_SCSI_LOGGING=y
> 
> #
> # SCSI Transports
> #
> # CONFIG_SCSI_SPI_ATTRS is not set
> # CONFIG_SCSI_FC_ATTRS is not set
> # CONFIG_SCSI_ISCSI_ATTRS is not set
> # CONFIG_SCSI_SAS_ATTRS is not set
> # CONFIG_SCSI_SAS_LIBSAS is not set
> 
> #
> # SCSI low-level drivers
> #
> # CONFIG_ISCSI_TCP is not set
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_3W_9XXX is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AACRAID is not set
> # CONFIG_SCSI_AIC7XXX is not set
> # CONFIG_SCSI_AIC7XXX_OLD is not set
> # CONFIG_SCSI_AIC79XX is not set
> # CONFIG_SCSI_AIC94XX is not set
> # CONFIG_SCSI_ARCMSR is not set
> # CONFIG_MEGARAID_NEWGEN is not set
> # CONFIG_MEGARAID_LEGACY is not set
> # CONFIG_MEGARAID_SAS is not set
> # CONFIG_SCSI_HPTIOP is not set
> # CONFIG_SCSI_BUSLOGIC is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_IPS is not set
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_STEX is not set
> # CONFIG_SCSI_SYM53C8XX_2 is not set
> # CONFIG_SCSI_IPR is not set
> # CONFIG_SCSI_QLOGIC_1280 is not set
> # CONFIG_SCSI_QLA_FC is not set
> # CONFIG_SCSI_QLA_ISCSI is not set
> # CONFIG_SCSI_LPFC is not set
> # CONFIG_SCSI_DC395x is not set
> # CONFIG_SCSI_DC390T is not set
> # CONFIG_SCSI_DEBUG is not set
> 
> #
> # Serial ATA (prod) and Parallel ATA (experimental) drivers
> #
> CONFIG_ATA=y
> CONFIG_SATA_AHCI=y
> # CONFIG_SATA_SVW is not set
> # CONFIG_ATA_PIIX is not set
> # CONFIG_SATA_MV is not set
> # CONFIG_SATA_NV is not set
> # CONFIG_PDC_ADMA is not set
> # CONFIG_SATA_QSTOR is not set
> # CONFIG_SATA_PROMISE is not set
> # CONFIG_SATA_SX4 is not set
> # CONFIG_SATA_SIL is not set
> # CONFIG_SATA_SIL24 is not set
> # CONFIG_SATA_SIS is not set
> # CONFIG_SATA_ULI is not set
> # CONFIG_SATA_VIA is not set
> # CONFIG_SATA_VITESSE is not set
> CONFIG_SATA_INTEL_COMBINED=y
> # CONFIG_PATA_ALI is not set
> # CONFIG_PATA_AMD is not set
> # CONFIG_PATA_ARTOP is not set
> # CONFIG_PATA_ATIIXP is not set
> # CONFIG_PATA_CMD64X is not set
> # CONFIG_PATA_CS5520 is not set
> # CONFIG_PATA_CS5530 is not set
> # CONFIG_PATA_CYPRESS is not set
> # CONFIG_PATA_EFAR is not set
> # CONFIG_ATA_GENERIC is not set
> # CONFIG_PATA_HPT366 is not set
> # CONFIG_PATA_HPT37X is not set
> # CONFIG_PATA_HPT3X2N is not set
> # CONFIG_PATA_HPT3X3 is not set
> # CONFIG_PATA_IT821X is not set
> # CONFIG_PATA_JMICRON is not set
> # CONFIG_PATA_TRIFLEX is not set
> # CONFIG_PATA_MPIIX is not set
> # CONFIG_PATA_OLDPIIX is not set
> # CONFIG_PATA_NETCELL is not set
> # CONFIG_PATA_NS87410 is not set
> # CONFIG_PATA_OPTI is not set
> # CONFIG_PATA_OPTIDMA is not set
> # CONFIG_PATA_PDC_OLD is not set
> # CONFIG_PATA_RADISYS is not set
> # CONFIG_PATA_RZ1000 is not set
> # CONFIG_PATA_SC1200 is not set
> # CONFIG_PATA_SERVERWORKS is not set
> # CONFIG_PATA_PDC2027X is not set
> # CONFIG_PATA_SIL680 is not set
> # CONFIG_PATA_SIS is not set
> # CONFIG_PATA_VIA is not set
> # CONFIG_PATA_WINBOND is not set
> 
> #
> # Multi-device support (RAID and LVM)
> #
> CONFIG_MD=y
> CONFIG_BLK_DEV_MD=y
> CONFIG_MD_LINEAR=y
> CONFIG_MD_RAID0=y
> CONFIG_MD_RAID1=y
> # CONFIG_MD_RAID10 is not set
> # CONFIG_MD_RAID456 is not set
> # CONFIG_MD_MULTIPATH is not set
> # CONFIG_MD_FAULTY is not set
> # CONFIG_BLK_DEV_DM is not set
> 
> #
> # Fusion MPT device support
> #
> # CONFIG_FUSION is not set
> # CONFIG_FUSION_SPI is not set
> # CONFIG_FUSION_FC is not set
> # CONFIG_FUSION_SAS is not set
> 
> #
> # IEEE 1394 (FireWire) support
> #
> CONFIG_IEEE1394=y
> 
> #
> # Subsystem Options
> #
> # CONFIG_IEEE1394_VERBOSEDEBUG is not set
> CONFIG_IEEE1394_OUI_DB=y
> CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
> CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
> # CONFIG_IEEE1394_EXPORT_FULL_API is not set
> 
> #
> # Device Drivers
> #
> 
> #
> # Texas Instruments PCILynx requires I2C
> #
> CONFIG_IEEE1394_OHCI1394=y
> 
> #
> # Protocol Drivers
> #
> CONFIG_IEEE1394_VIDEO1394=y
> CONFIG_IEEE1394_SBP2=y
> # CONFIG_IEEE1394_ETH1394 is not set
> # CONFIG_IEEE1394_DV1394 is not set
> CONFIG_IEEE1394_RAWIO=y
> 
> #
> # I2O device support
> #
> # CONFIG_I2O is not set
> 
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
> CONFIG_DUMMY=y
> # CONFIG_BONDING is not set
> CONFIG_EQUALIZER=y
> CONFIG_TUN=y
> # CONFIG_NET_SB1000 is not set
> 
> #
> # ARCnet devices
> #
> # CONFIG_ARCNET is not set
> 
> 
> #
> # PHY device support
> #
> 
> #
> # Ethernet (10 or 100Mbit)
> #
> # CONFIG_NET_ETHERNET is not set
> 
> #
> # Ethernet (1000 Mbit)
> #
> # CONFIG_ACENIC is not set
> # CONFIG_DL2K is not set
> # CONFIG_E1000 is not set
> # CONFIG_NS83820 is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_YELLOWFIN is not set
> # CONFIG_R8169 is not set
> # CONFIG_SIS190 is not set
> # CONFIG_SKGE is not set
> CONFIG_SKY2=y
> # CONFIG_SK98LIN is not set
> # CONFIG_TIGON3 is not set
> # CONFIG_BNX2 is not set
> # CONFIG_QLA3XXX is not set
> 
> #
> # Ethernet (10000 Mbit)
> #
> # CONFIG_CHELSIO_T1 is not set
> # CONFIG_IXGB is not set
> # CONFIG_S2IO is not set
> # CONFIG_MYRI10GE is not set
> 
> #
> # Token Ring devices
> #
> # CONFIG_TR is not set
> 
> #
> # Wireless LAN (non-hamradio)
> #
> CONFIG_NET_RADIO=y
> # CONFIG_NET_WIRELESS_RTNETLINK is not set
> 
> #
> # Obsolete Wireless cards support (pre-802.11)
> #
> # CONFIG_STRIP is not set
> 
> #
> # Wireless 802.11b ISA/PCI cards support
> #
> # CONFIG_IPW2100 is not set
> # CONFIG_IPW2200 is not set
> # CONFIG_AIRO is not set
> # CONFIG_HERMES is not set
> # CONFIG_ATMEL is not set
> 
> #
> # Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
> #
> # CONFIG_PRISM54 is not set
> # CONFIG_USB_ZD1201 is not set
> # CONFIG_HOSTAP is not set
> CONFIG_NET_WIRELESS=y
> 
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
> # CONFIG_FDDI is not set
> # CONFIG_HIPPI is not set
> CONFIG_PPP=y
> CONFIG_PPP_MULTILINK=y
> CONFIG_PPP_FILTER=y
> CONFIG_PPP_ASYNC=y
> CONFIG_PPP_SYNC_TTY=y
> CONFIG_PPP_DEFLATE=y
> CONFIG_PPP_BSDCOMP=y
> CONFIG_PPP_MPPE=y
> # CONFIG_PPPOE is not set
> # CONFIG_SLIP is not set
> CONFIG_SLHC=y
> # CONFIG_NET_FC is not set
> # CONFIG_SHAPER is not set
> # CONFIG_NETCONSOLE is not set
> # CONFIG_NETPOLL is not set
> # CONFIG_NET_POLL_CONTROLLER is not set
> 
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
> 
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
> 
> #
> # Input device support
> #
> CONFIG_INPUT=y
> # CONFIG_INPUT_FF_MEMLESS is not set
> 
> #
> # Userland interfaces
> #
> CONFIG_INPUT_MOUSEDEV=y
> CONFIG_INPUT_MOUSEDEV_PSAUX=y
> CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
> CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
> # CONFIG_INPUT_JOYDEV is not set
> # CONFIG_INPUT_TSDEV is not set
> CONFIG_INPUT_EVDEV=y
> # CONFIG_INPUT_EVBUG is not set
> 
> #
> # Input Device Drivers
> #
> CONFIG_INPUT_KEYBOARD=y
> CONFIG_KEYBOARD_ATKBD=y
> # CONFIG_KEYBOARD_SUNKBD is not set
> # CONFIG_KEYBOARD_LKKBD is not set
> # CONFIG_KEYBOARD_XTKBD is not set
> # CONFIG_KEYBOARD_NEWTON is not set
> # CONFIG_KEYBOARD_STOWAWAY is not set
> CONFIG_INPUT_MOUSE=y
> CONFIG_MOUSE_PS2=y
> # CONFIG_MOUSE_SERIAL is not set
> # CONFIG_MOUSE_VSXXXAA is not set
> # CONFIG_INPUT_JOYSTICK is not set
> # CONFIG_INPUT_TOUCHSCREEN is not set
> CONFIG_INPUT_MISC=y
> CONFIG_INPUT_PCSPKR=y
> # CONFIG_INPUT_UINPUT is not set
> 
> #
> # Hardware I/O ports
> #
> CONFIG_SERIO=y
> CONFIG_SERIO_I8042=y
> CONFIG_SERIO_SERPORT=y
> # CONFIG_SERIO_CT82C710 is not set
> # CONFIG_SERIO_PCIPS2 is not set
> CONFIG_SERIO_LIBPS2=y
> # CONFIG_SERIO_RAW is not set
> # CONFIG_GAMEPORT is not set
> 
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_HW_CONSOLE=y
> # CONFIG_VT_HW_CONSOLE_BINDING is not set
> # CONFIG_SERIAL_NONSTANDARD is not set
> 
> #
> # Serial drivers
> #
> CONFIG_SERIAL_8250=y
> CONFIG_SERIAL_8250_CONSOLE=y
> CONFIG_SERIAL_8250_PCI=y
> CONFIG_SERIAL_8250_PNP=y
> CONFIG_SERIAL_8250_NR_UARTS=48
> CONFIG_SERIAL_8250_RUNTIME_UARTS=4
> # CONFIG_SERIAL_8250_EXTENDED is not set
> 
> #
> # Non-8250 serial port support
> #
> CONFIG_SERIAL_CORE=y
> CONFIG_SERIAL_CORE_CONSOLE=y
> # CONFIG_SERIAL_JSM is not set
> CONFIG_UNIX98_PTYS=y
> CONFIG_LEGACY_PTYS=y
> CONFIG_LEGACY_PTY_COUNT=256
> 
> #
> # IPMI
> #
> # CONFIG_IPMI_HANDLER is not set
> 
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> CONFIG_HW_RANDOM=y
> CONFIG_HW_RANDOM_INTEL=y
> # CONFIG_HW_RANDOM_AMD is not set
> # CONFIG_HW_RANDOM_GEODE is not set
> CONFIG_NVRAM=y
> CONFIG_RTC=y
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
> 
> #
> # Ftape, the floppy tape device driver
> #
> CONFIG_AGP=y
> CONFIG_AGP_AMD64=y
> # CONFIG_AGP_INTEL is not set
> # CONFIG_AGP_SIS is not set
> # CONFIG_AGP_VIA is not set
> # CONFIG_DRM is not set
> # CONFIG_MWAVE is not set
> # CONFIG_PC8736x_GPIO is not set
> CONFIG_RAW_DRIVER=y
> CONFIG_MAX_RAW_DEVS=256
> CONFIG_HPET=y
> # CONFIG_HPET_RTC_IRQ is not set
> CONFIG_HPET_MMAP=y
> CONFIG_HANGCHECK_TIMER=y
> 
> #
> # TPM devices
> #
> # CONFIG_TCG_TPM is not set
> # CONFIG_TELCLOCK is not set
> 
> #
> # I2C support
> #
> # CONFIG_I2C is not set
> 
> #
> # SPI support
> #
> # CONFIG_SPI is not set
> # CONFIG_SPI_MASTER is not set
> 
> #
> # Dallas's 1-wire bus
> #
> # CONFIG_W1 is not set
> 
> #
> # Hardware Monitoring support
> #
> # CONFIG_HWMON is not set
> # CONFIG_HWMON_VID is not set
> 
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
> 
> #
> # Digital Video Broadcasting Devices
> #
> # CONFIG_DVB is not set
> # CONFIG_USB_DABUSB is not set
> 
> #
> # Graphics support
> #
> CONFIG_FIRMWARE_EDID=y
> CONFIG_FB=y
> CONFIG_FB_CFB_FILLRECT=y
> CONFIG_FB_CFB_COPYAREA=y
> CONFIG_FB_CFB_IMAGEBLIT=y
> # CONFIG_FB_MACMODES is not set
> # CONFIG_FB_BACKLIGHT is not set
> CONFIG_FB_MODE_HELPERS=y
> CONFIG_FB_TILEBLITTING=y
> # CONFIG_FB_CIRRUS is not set
> # CONFIG_FB_PM2 is not set
> # CONFIG_FB_CYBER2000 is not set
> # CONFIG_FB_ARC is not set
> # CONFIG_FB_ASILIANT is not set
> # CONFIG_FB_IMSTT is not set
> CONFIG_FB_VGA16=y
> CONFIG_FB_VESA=y
> # CONFIG_FB_HGA is not set
> # CONFIG_FB_S1D13XXX is not set
> # CONFIG_FB_NVIDIA is not set
> # CONFIG_FB_RIVA is not set
> # CONFIG_FB_INTEL is not set
> # CONFIG_FB_MATROX is not set
> # CONFIG_FB_RADEON is not set
> # CONFIG_FB_ATY128 is not set
> # CONFIG_FB_ATY is not set
> # CONFIG_FB_SAVAGE is not set
> # CONFIG_FB_SIS is not set
> # CONFIG_FB_NEOMAGIC is not set
> # CONFIG_FB_KYRO is not set
> # CONFIG_FB_3DFX is not set
> # CONFIG_FB_VOODOO1 is not set
> # CONFIG_FB_TRIDENT is not set
> # CONFIG_FB_GEODE is not set
> # CONFIG_FB_VIRTUAL is not set
> 
> #
> # Console display driver support
> #
> CONFIG_VGA_CONSOLE=y
> # CONFIG_VGACON_SOFT_SCROLLBACK is not set
> CONFIG_VIDEO_SELECT=y
> CONFIG_DUMMY_CONSOLE=y
> CONFIG_FRAMEBUFFER_CONSOLE=y
> # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> # CONFIG_FONTS is not set
> CONFIG_FONT_8x8=y
> CONFIG_FONT_8x16=y
> 
> #
> # Logo configuration
> #
> # CONFIG_LOGO is not set
> # CONFIG_BACKLIGHT_LCD_SUPPORT is not set
> 
> #
> # Sound
> #
> CONFIG_SOUND=y
> 
> #
> # Advanced Linux Sound Architecture
> #
> CONFIG_SND=y
> CONFIG_SND_TIMER=y
> CONFIG_SND_PCM=y
> CONFIG_SND_SEQUENCER=y
> CONFIG_SND_SEQ_DUMMY=y
> CONFIG_SND_OSSEMUL=y
> CONFIG_SND_MIXER_OSS=y
> CONFIG_SND_PCM_OSS=y
> CONFIG_SND_PCM_OSS_PLUGINS=y
> CONFIG_SND_SEQUENCER_OSS=y
> CONFIG_SND_RTCTIMER=y
> CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
> # CONFIG_SND_DYNAMIC_MINORS is not set
> CONFIG_SND_SUPPORT_OLD_API=y
> CONFIG_SND_VERBOSE_PROCFS=y
> # CONFIG_SND_VERBOSE_PRINTK is not set
> # CONFIG_SND_DEBUG is not set
> 
> #
> # Generic devices
> #
> CONFIG_SND_AC97_CODEC=y
> CONFIG_SND_AC97_BUS=y
> # CONFIG_SND_DUMMY is not set
> # CONFIG_SND_VIRMIDI is not set
> # CONFIG_SND_MTPAV is not set
> # CONFIG_SND_SERIAL_U16550 is not set
> # CONFIG_SND_MPU401 is not set
> 
> #
> # PCI devices
> #
> # CONFIG_SND_AD1889 is not set
> # CONFIG_SND_ALS300 is not set
> # CONFIG_SND_ALS4000 is not set
> # CONFIG_SND_ALI5451 is not set
> # CONFIG_SND_ATIIXP is not set
> # CONFIG_SND_ATIIXP_MODEM is not set
> # CONFIG_SND_AU8810 is not set
> # CONFIG_SND_AU8820 is not set
> # CONFIG_SND_AU8830 is not set
> # CONFIG_SND_AZT3328 is not set
> # CONFIG_SND_BT87X is not set
> # CONFIG_SND_CA0106 is not set
> # CONFIG_SND_CMIPCI is not set
> # CONFIG_SND_CS4281 is not set
> # CONFIG_SND_CS46XX is not set
> # CONFIG_SND_DARLA20 is not set
> # CONFIG_SND_GINA20 is not set
> # CONFIG_SND_LAYLA20 is not set
> # CONFIG_SND_DARLA24 is not set
> # CONFIG_SND_GINA24 is not set
> # CONFIG_SND_LAYLA24 is not set
> # CONFIG_SND_MONA is not set
> # CONFIG_SND_MIA is not set
> # CONFIG_SND_ECHO3G is not set
> # CONFIG_SND_INDIGO is not set
> # CONFIG_SND_INDIGOIO is not set
> # CONFIG_SND_INDIGODJ is not set
> # CONFIG_SND_EMU10K1 is not set
> # CONFIG_SND_EMU10K1X is not set
> # CONFIG_SND_ENS1370 is not set
> # CONFIG_SND_ENS1371 is not set
> # CONFIG_SND_ES1938 is not set
> # CONFIG_SND_ES1968 is not set
> # CONFIG_SND_FM801 is not set
> CONFIG_SND_HDA_INTEL=y
> # CONFIG_SND_HDSP is not set
> # CONFIG_SND_HDSPM is not set
> # CONFIG_SND_ICE1712 is not set
> # CONFIG_SND_ICE1724 is not set
> CONFIG_SND_INTEL8X0=y
> # CONFIG_SND_INTEL8X0M is not set
> # CONFIG_SND_KORG1212 is not set
> # CONFIG_SND_MAESTRO3 is not set
> # CONFIG_SND_MIXART is not set
> # CONFIG_SND_NM256 is not set
> # CONFIG_SND_PCXHR is not set
> # CONFIG_SND_RIPTIDE is not set
> # CONFIG_SND_RME32 is not set
> # CONFIG_SND_RME96 is not set
> # CONFIG_SND_RME9652 is not set
> # CONFIG_SND_SONICVIBES is not set
> # CONFIG_SND_TRIDENT is not set
> # CONFIG_SND_VIA82XX is not set
> # CONFIG_SND_VIA82XX_MODEM is not set
> # CONFIG_SND_VX222 is not set
> # CONFIG_SND_YMFPCI is not set
> # CONFIG_SND_AC97_POWER_SAVE is not set
> 
> #
> # USB devices
> #
> # CONFIG_SND_USB_AUDIO is not set
> # CONFIG_SND_USB_USX2Y is not set
> 
> #
> # Open Sound System
> #
> # CONFIG_SOUND_PRIME is not set
> 
> #
> # USB support
> #
> CONFIG_USB_ARCH_HAS_HCD=y
> CONFIG_USB_ARCH_HAS_OHCI=y
> CONFIG_USB_ARCH_HAS_EHCI=y
> CONFIG_USB=y
> # CONFIG_USB_DEBUG is not set
> 
> #
> # Miscellaneous USB options
> #
> CONFIG_USB_DEVICEFS=y
> # CONFIG_USB_BANDWIDTH is not set
> # CONFIG_USB_DYNAMIC_MINORS is not set
> CONFIG_USB_SUSPEND=y
> # CONFIG_USB_OTG is not set
> 
> #
> # USB Host Controller Drivers
> #
> CONFIG_USB_EHCI_HCD=y
> CONFIG_USB_EHCI_SPLIT_ISO=y
> CONFIG_USB_EHCI_ROOT_HUB_TT=y
> # CONFIG_USB_EHCI_TT_NEWSCHED is not set
> # CONFIG_USB_ISP116X_HCD is not set
> # CONFIG_USB_OHCI_HCD is not set
> CONFIG_USB_UHCI_HCD=y
> # CONFIG_USB_SL811_HCD is not set
> 
> #
> # USB Device Class drivers
> #
> # CONFIG_USB_ACM is not set
> CONFIG_USB_PRINTER=y
> 
> #
> # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
> #
> 
> #
> # may also be needed; see USB_STORAGE Help for more information
> #
> CONFIG_USB_STORAGE=y
> # CONFIG_USB_STORAGE_DEBUG is not set
> # CONFIG_USB_STORAGE_DATAFAB is not set
> # CONFIG_USB_STORAGE_FREECOM is not set
> # CONFIG_USB_STORAGE_ISD200 is not set
> # CONFIG_USB_STORAGE_DPCM is not set
> # CONFIG_USB_STORAGE_USBAT is not set
> # CONFIG_USB_STORAGE_SDDR09 is not set
> # CONFIG_USB_STORAGE_SDDR55 is not set
> # CONFIG_USB_STORAGE_JUMPSHOT is not set
> # CONFIG_USB_STORAGE_ALAUDA is not set
> # CONFIG_USB_STORAGE_KARMA is not set
> # CONFIG_USB_LIBUSUAL is not set
> 
> #
> # USB Input Devices
> #
> CONFIG_USB_HID=y
> CONFIG_USB_HIDINPUT=y
> # CONFIG_USB_HIDINPUT_POWERBOOK is not set
> # CONFIG_HID_FF is not set
> CONFIG_USB_HIDDEV=y
> # CONFIG_USB_AIPTEK is not set
> # CONFIG_USB_WACOM is not set
> # CONFIG_USB_ACECAD is not set
> # CONFIG_USB_KBTAB is not set
> # CONFIG_USB_POWERMATE is not set
> # CONFIG_USB_TOUCHSCREEN is not set
> # CONFIG_USB_YEALINK is not set
> # CONFIG_USB_XPAD is not set
> # CONFIG_USB_ATI_REMOTE is not set
> # CONFIG_USB_ATI_REMOTE2 is not set
> # CONFIG_USB_KEYSPAN_REMOTE is not set
> # CONFIG_USB_APPLETOUCH is not set
> 
> #
> # USB Imaging devices
> #
> # CONFIG_USB_MDC800 is not set
> # CONFIG_USB_MICROTEK is not set
> 
> #
> # USB Network Adapters
> #
> # CONFIG_USB_CATC is not set
> # CONFIG_USB_KAWETH is not set
> # CONFIG_USB_PEGASUS is not set
> # CONFIG_USB_RTL8150 is not set
> # CONFIG_USB_USBNET_MII is not set
> # CONFIG_USB_USBNET is not set
> CONFIG_USB_MON=y
> 
> #
> # USB port drivers
> #
> 
> #
> # USB Serial Converter support
> #
> # CONFIG_USB_SERIAL is not set
> 
> #
> # USB Miscellaneous drivers
> #
> # CONFIG_USB_EMI62 is not set
> # CONFIG_USB_EMI26 is not set
> # CONFIG_USB_ADUTUX is not set
> # CONFIG_USB_AUERSWALD is not set
> # CONFIG_USB_RIO500 is not set
> # CONFIG_USB_LEGOTOWER is not set
> # CONFIG_USB_LCD is not set
> # CONFIG_USB_LED is not set
> # CONFIG_USB_CYPRESS_CY7C63 is not set
> # CONFIG_USB_CYTHERM is not set
> # CONFIG_USB_PHIDGET is not set
> # CONFIG_USB_IDMOUSE is not set
> # CONFIG_USB_FTDI_ELAN is not set
> # CONFIG_USB_APPLEDISPLAY is not set
> # CONFIG_USB_SISUSBVGA is not set
> # CONFIG_USB_LD is not set
> # CONFIG_USB_TRANCEVIBRATOR is not set
> # CONFIG_USB_TEST is not set
> 
> #
> # USB DSL modem support
> #
> 
> #
> # USB Gadget Support
> #
> # CONFIG_USB_GADGET is not set
> 
> #
> # MMC/SD Card support
> #
> # CONFIG_MMC is not set
> 
> #
> # LED devices
> #
> # CONFIG_NEW_LEDS is not set
> 
> #
> # LED drivers
> #
> 
> #
> # LED Triggers
> #
> 
> #
> # InfiniBand support
> #
> # CONFIG_INFINIBAND is not set
> 
> #
> # EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
> #
> # CONFIG_EDAC is not set
> 
> #
> # Real Time Clock
> #
> # CONFIG_RTC_CLASS is not set
> 
> #
> # DMA Engine support
> #
> # CONFIG_DMA_ENGINE is not set
> 
> #
> # DMA Clients
> #
> 
> #
> # DMA Devices
> #
> 
> #
> # Firmware Drivers
> #
> # CONFIG_EDD is not set
> # CONFIG_DELL_RBU is not set
> # CONFIG_DCDBAS is not set
> 
> #
> # File systems
> #
> CONFIG_EXT2_FS=y
> CONFIG_EXT2_FS_XATTR=y
> CONFIG_EXT2_FS_POSIX_ACL=y
> CONFIG_EXT2_FS_SECURITY=y
> # CONFIG_EXT2_FS_XIP is not set
> CONFIG_EXT3_FS=y
> CONFIG_EXT3_FS_XATTR=y
> CONFIG_EXT3_FS_POSIX_ACL=y
> CONFIG_EXT3_FS_SECURITY=y
> # CONFIG_EXT4DEV_FS is not set
> CONFIG_JBD=y
> # CONFIG_JBD_DEBUG is not set
> CONFIG_FS_MBCACHE=y
> CONFIG_REISERFS_FS=y
> # CONFIG_REISERFS_CHECK is not set
> CONFIG_REISERFS_PROC_INFO=y
> CONFIG_REISERFS_FS_XATTR=y
> CONFIG_REISERFS_FS_POSIX_ACL=y
> CONFIG_REISERFS_FS_SECURITY=y
> # CONFIG_JFS_FS is not set
> CONFIG_FS_POSIX_ACL=y
> # CONFIG_XFS_FS is not set
> # CONFIG_GFS2_FS is not set
> # CONFIG_OCFS2_FS is not set
> # CONFIG_MINIX_FS is not set
> # CONFIG_ROMFS_FS is not set
> CONFIG_INOTIFY=y
> CONFIG_INOTIFY_USER=y
> CONFIG_QUOTA=y
> CONFIG_QFMT_V1=y
> CONFIG_QFMT_V2=y
> CONFIG_QUOTACTL=y
> CONFIG_DNOTIFY=y
> CONFIG_AUTOFS_FS=y
> CONFIG_AUTOFS4_FS=y
> CONFIG_FUSE_FS=y
> 
> #
> # CD-ROM/DVD Filesystems
> #
> CONFIG_ISO9660_FS=y
> CONFIG_JOLIET=y
> CONFIG_ZISOFS=y
> CONFIG_ZISOFS_FS=y
> CONFIG_UDF_FS=y
> CONFIG_UDF_NLS=y
> 
> #
> # DOS/FAT/NT Filesystems
> #
> CONFIG_FAT_FS=y
> CONFIG_MSDOS_FS=y
> CONFIG_VFAT_FS=y
> CONFIG_FAT_DEFAULT_CODEPAGE=437
> CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
> CONFIG_NTFS_FS=y
> # CONFIG_NTFS_DEBUG is not set
> CONFIG_NTFS_RW=y
> 
> #
> # Pseudo filesystems
> #
> CONFIG_PROC_FS=y
> CONFIG_PROC_KCORE=y
> CONFIG_PROC_SYSCTL=y
> CONFIG_SYSFS=y
> CONFIG_TMPFS=y
> # CONFIG_TMPFS_POSIX_ACL is not set
> # CONFIG_HUGETLBFS is not set
> # CONFIG_HUGETLB_PAGE is not set
> CONFIG_RAMFS=y
> CONFIG_CONFIGFS_FS=y
> 
> #
> # Miscellaneous filesystems
> #
> # CONFIG_ADFS_FS is not set
> # CONFIG_AFFS_FS is not set
> CONFIG_ECRYPT_FS=y
> # CONFIG_HFS_FS is not set
> # CONFIG_HFSPLUS_FS is not set
> # CONFIG_BEFS_FS is not set
> # CONFIG_BFS_FS is not set
> # CONFIG_EFS_FS is not set
> CONFIG_CRAMFS=y
> # CONFIG_VXFS_FS is not set
> # CONFIG_HPFS_FS is not set
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_SYSV_FS is not set
> # CONFIG_UFS_FS is not set
> 
> #
> # Network File Systems
> #
> # CONFIG_NFS_FS is not set
> # CONFIG_NFSD is not set
> CONFIG_SMB_FS=y
> CONFIG_SMB_NLS_DEFAULT=y
> CONFIG_SMB_NLS_REMOTE="cp437"
> CONFIG_CIFS=y
> CONFIG_CIFS_STATS=y
> CONFIG_CIFS_STATS2=y
> # CONFIG_CIFS_WEAK_PW_HASH is not set
> CONFIG_CIFS_XATTR=y
> CONFIG_CIFS_POSIX=y
> # CONFIG_CIFS_DEBUG2 is not set
> # CONFIG_CIFS_EXPERIMENTAL is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_CODA_FS is not set
> # CONFIG_AFS_FS is not set
> # CONFIG_9P_FS is not set
> 
> #
> # Partition Types
> #
> # CONFIG_PARTITION_ADVANCED is not set
> CONFIG_MSDOS_PARTITION=y
> 
> #
> # Native Language Support
> #
> CONFIG_NLS=y
> CONFIG_NLS_DEFAULT="cp437"
> CONFIG_NLS_CODEPAGE_437=y
> # CONFIG_NLS_CODEPAGE_737 is not set
> # CONFIG_NLS_CODEPAGE_775 is not set
> CONFIG_NLS_CODEPAGE_850=y
> # CONFIG_NLS_CODEPAGE_852 is not set
> # CONFIG_NLS_CODEPAGE_855 is not set
> # CONFIG_NLS_CODEPAGE_857 is not set
> # CONFIG_NLS_CODEPAGE_860 is not set
> # CONFIG_NLS_CODEPAGE_861 is not set
> # CONFIG_NLS_CODEPAGE_862 is not set
> # CONFIG_NLS_CODEPAGE_863 is not set
> # CONFIG_NLS_CODEPAGE_864 is not set
> # CONFIG_NLS_CODEPAGE_865 is not set
> # CONFIG_NLS_CODEPAGE_866 is not set
> # CONFIG_NLS_CODEPAGE_869 is not set
> # CONFIG_NLS_CODEPAGE_936 is not set
> # CONFIG_NLS_CODEPAGE_950 is not set
> # CONFIG_NLS_CODEPAGE_932 is not set
> # CONFIG_NLS_CODEPAGE_949 is not set
> # CONFIG_NLS_CODEPAGE_874 is not set
> # CONFIG_NLS_ISO8859_8 is not set
> # CONFIG_NLS_CODEPAGE_1250 is not set
> # CONFIG_NLS_CODEPAGE_1251 is not set
> CONFIG_NLS_ASCII=y
> CONFIG_NLS_ISO8859_1=y
> # CONFIG_NLS_ISO8859_2 is not set
> # CONFIG_NLS_ISO8859_3 is not set
> # CONFIG_NLS_ISO8859_4 is not set
> # CONFIG_NLS_ISO8859_5 is not set
> # CONFIG_NLS_ISO8859_6 is not set
> # CONFIG_NLS_ISO8859_7 is not set
> # CONFIG_NLS_ISO8859_9 is not set
> # CONFIG_NLS_ISO8859_13 is not set
> # CONFIG_NLS_ISO8859_14 is not set
> CONFIG_NLS_ISO8859_15=y
> # CONFIG_NLS_KOI8_R is not set
> # CONFIG_NLS_KOI8_U is not set
> CONFIG_NLS_UTF8=y
> 
> #
> # Instrumentation Support
> #
> CONFIG_PROFILING=y
> CONFIG_OPROFILE=y
> CONFIG_KPROBES=y
> 
> #
> # Kernel hacking
> #
> CONFIG_TRACE_IRQFLAGS_SUPPORT=y
> # CONFIG_PRINTK_TIME is not set
> CONFIG_ENABLE_MUST_CHECK=y
> CONFIG_MAGIC_SYSRQ=y
> CONFIG_UNUSED_SYMBOLS=y
> CONFIG_DEBUG_KERNEL=y
> CONFIG_LOG_BUF_SHIFT=17
> CONFIG_DETECT_SOFTLOCKUP=y
> CONFIG_SCHEDSTATS=y
> # CONFIG_DEBUG_SLAB is not set
> # CONFIG_DEBUG_PREEMPT is not set
> # CONFIG_DEBUG_RT_MUTEXES is not set
> # CONFIG_RT_MUTEX_TESTER is not set
> # CONFIG_DEBUG_SPINLOCK is not set
> # CONFIG_DEBUG_MUTEXES is not set
> # CONFIG_DEBUG_RWSEMS is not set
> # CONFIG_DEBUG_LOCK_ALLOC is not set
> # CONFIG_PROVE_LOCKING is not set
> # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
> # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
> # CONFIG_DEBUG_KOBJECT is not set
> # CONFIG_DEBUG_INFO is not set
> CONFIG_DEBUG_FS=y
> # CONFIG_DEBUG_VM is not set
> # CONFIG_DEBUG_LIST is not set
> # CONFIG_FRAME_POINTER is not set
> # CONFIG_UNWIND_INFO is not set
> CONFIG_FORCED_INLINING=y
> # CONFIG_HEADERS_CHECK is not set
> # CONFIG_RCU_TORTURE_TEST is not set
> # CONFIG_LKDTM is not set
> # CONFIG_DEBUG_RODATA is not set
> # CONFIG_IOMMU_DEBUG is not set
> # CONFIG_DEBUG_STACKOVERFLOW is not set
> # CONFIG_DEBUG_STACK_USAGE is not set
> 
> #
> # Security options
> #
> CONFIG_KEYS=y
> CONFIG_KEYS_DEBUG_PROC_KEYS=y
> CONFIG_SECURITY=y
> CONFIG_SECURITY_NETWORK=y
> # CONFIG_SECURITY_NETWORK_XFRM is not set
> CONFIG_SECURITY_CAPABILITIES=y
> CONFIG_SECURITY_ROOTPLUG=y
> 
> #
> # Cryptographic options
> #
> CONFIG_CRYPTO=y
> CONFIG_CRYPTO_ALGAPI=y
> CONFIG_CRYPTO_BLKCIPHER=y
> CONFIG_CRYPTO_HASH=y
> CONFIG_CRYPTO_MANAGER=y
> CONFIG_CRYPTO_HMAC=y
> CONFIG_CRYPTO_NULL=y
> CONFIG_CRYPTO_MD4=y
> CONFIG_CRYPTO_MD5=y
> CONFIG_CRYPTO_SHA1=y
> CONFIG_CRYPTO_SHA256=y
> CONFIG_CRYPTO_SHA512=y
> CONFIG_CRYPTO_WP512=y
> CONFIG_CRYPTO_TGR192=y
> CONFIG_CRYPTO_ECB=y
> CONFIG_CRYPTO_CBC=y
> CONFIG_CRYPTO_DES=y
> CONFIG_CRYPTO_BLOWFISH=y
> # CONFIG_CRYPTO_TWOFISH is not set
> CONFIG_CRYPTO_TWOFISH_COMMON=y
> CONFIG_CRYPTO_TWOFISH_X86_64=y
> CONFIG_CRYPTO_SERPENT=y
> # CONFIG_CRYPTO_AES is not set
> CONFIG_CRYPTO_AES_X86_64=y
> CONFIG_CRYPTO_CAST5=y
> CONFIG_CRYPTO_CAST6=y
> CONFIG_CRYPTO_TEA=y
> CONFIG_CRYPTO_ARC4=y
> CONFIG_CRYPTO_KHAZAD=y
> CONFIG_CRYPTO_ANUBIS=y
> CONFIG_CRYPTO_DEFLATE=y
> CONFIG_CRYPTO_MICHAEL_MIC=y
> CONFIG_CRYPTO_CRC32C=y
> # CONFIG_CRYPTO_TEST is not set
> 
> #
> # Hardware crypto devices
> #
> 
> #
> # Library routines
> #
> CONFIG_CRC_CCITT=y
> CONFIG_CRC16=y
> CONFIG_CRC32=y
> CONFIG_LIBCRC32C=y
> CONFIG_ZLIB_INFLATE=y
> CONFIG_ZLIB_DEFLATE=y
> CONFIG_TEXTSEARCH=y
> CONFIG_TEXTSEARCH_KMP=y
> CONFIG_TEXTSEARCH_BM=y
> CONFIG_TEXTSEARCH_FSM=y
> CONFIG_PLIST=y
> 
> -
> To unsubscribe from this list: send the line "unsubscribe 
> linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-14  0:56 Greg Trounson
  2007-02-14 17:47 ` Bill Davidsen
@ 2007-04-01 14:19 ` Håkan Lindqvist
  1 sibling, 0 replies; 18+ messages in thread
From: Håkan Lindqvist @ 2007-04-01 14:19 UTC (permalink / raw)
  To: linux-kernel; +Cc: Greg Trounson


[-- Attachment #1.1: Type: text/plain, Size: 2405 bytes --]

On Wed, 2007-02-14 at 13:56 +1300, Greg Trounson wrote: 
> At the risk of sounding like a "me too" post:
> 
> I also have an Asus P5W-DH, with the following drives connected:
> 
> SATA: ST3250820AS, connected to sata1
> PATA: HL-DT-ST GSA-H12N, ATAPI DVD Writer, Primary master
> 
> On bootup of 2.6.19 and 2.6.20, the kernel stalls for 1 minute when probing sata2, 
> eventually giving up and continuing the boot process.  There is no physical sata2 
> connector on the Motherboard, just solder lugs between sata1 and sata3.  From other users 
> I understand this is really a Silicon Image SIL4723 SATA to 2-Port SATA splitter.  It is 
> detected by the kernel as a disk, as below.

I've had the same problem, in addition to the JMicron problem, but I
have noticed a clear improvement in 2.6.21-rc5. (I have not tried any of
the versions between 2.6.20 and this.)


I also have an Asus P5W DH Deluxe board, I normally only have PATA
devices hooked up fow now (two harddrives on the ICH PATA port and a
DVD-RW drive on the JMicron PATA port).

I used to have the same two main problems as have been discussed in this
thread:

1) The one you mention above, the kernel stopping a long time to wait
for the ata2 port (ICH SATA port 2, which really is linked to this SiL
RAID chip), unless I had very specific settings in BIOS regarding the
disk configuration.

2) The JMicron PATA breaking the kernel in various more or less
spectacular ways.

So up until now I've had to disable the JMicron controller entirely, and
have the ICH controller configured in a specific way in to be able to
boot properly.

With 2.6.21-rc5 BOTH of the above seem to have had a clear improvement.
Both seem to work correctly with my configuration, I do however have to
pass the "irqpoll" option to the kernel on boot.

For the sake of investigation I did hook up an extra drive on the sata1
(ICH) port, and noticed that while the ata1 initialized quickly and
correctly, having any SATA drive connected caused the ata2 problem to
reappear.
However, the kernel recovered A LOT quicker than it used to and when
everything had booted, it seems that everything worked correctly (except
that really shouldn't have been a "sdb" drive detected).

Attached is dmesg output from both cases.


Regards,
Håkan Lindqvist

(I am not subscribed to the list, please CC me on any replies.)

[-- Attachment #1.2: 2.6.20-rc5.txt --]
[-- Type: text/plain, Size: 24111 bytes --]

Linux version 2.6.21-rc5 (hawk@janne) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP PREEMPT Sun Apr 1 14:54:51 CEST 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000007fe80000 end: 000000007ff80000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000007ff80000 size: 000000000000e000 end: 000000007ff8e000 type: 3
copy_e820_map() start: 000000007ff8e000 size: 0000000000052000 end: 000000007ffe0000 type: 4
copy_e820_map() start: 000000007ffe0000 size: 0000000000020000 end: 0000000080000000 type: 2
copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end: 0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ff80000 (usable)
 BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data)
 BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
 BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 524160) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   524160
early_node_map[1] active PFN ranges
    0:        0 ->   524160
On node 0 totalpages: 524160
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 2303 pages used for memmap
  HighMem zone: 292481 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP 000FAF20, 0014 (r0 ACPIAM)
ACPI: RSDT 7FF80000, 0044 (r1 NEC              3000707 MSFT       97)
ACPI: FACP 7FF80200, 0081 (r1 A_M_I_ OEMFACP   3000707 MSFT       97)
ACPI: DSDT 7FF80590, 9560 (r1  A0543 A0543000        0 INTL 20060113)
ACPI: FACS 7FF8E000, 0040
ACPI: APIC 7FF80390, 0080 (r1 A_M_I_ OEMAPIC   3000707 MSFT       97)
ACPI: SLIC 7FF80410, 0176 (r1 NEC              3000707 MSFT       97)
ACPI: OEMB 7FF8E040, 0066 (r1 A_M_I_ AMI_OEM   3000707 MSFT       97)
ACPI: HPET 7FF89AF0, 0038 (r1 A_M_I_ OEMHPET   3000707 MSFT       97)
ACPI: MCFG 7FF89B30, 003C (r1 A_M_I_ OEMMCFG   3000707 MSFT       97)
ACPI: SSDT 7FF8E0B0, 01C6 (r1    AMI   CPU1PM        1 INTL 20060113)
ACPI: SSDT 7FF8E280, 013A (r1    AMI   CPU2PM        1 INTL 20060113)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000)
Built 1 zonelists.  Total pages: 520065
Kernel command line: root=/dev/hde2 ro irqpoll
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2404.237 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070604k/2096640k available (1679k kernel code, 24756k reserved, 668k data, 212k init, 1179136k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4f000 - 0xfffff000   ( 704 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc0351000 - 0xc0386000   ( 212 kB)
      .data : 0xc02a3c5d - 0xc034af74   ( 668 kB)
      .text : 0xc0100000 - 0xc02a3c5d   (1679 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Calibrating delay using timer specific routine.. 4818.55 BogoMIPS (lpj=9637105)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4808.23 BogoMIPS (lpj=9616466)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz stepping 06
Total of 2 processors activated (9626.78 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
APIC calibration not consistent with PM Timer: 97ms instead of 100ms
APIC delta adjusted to PM-Timer: 1669521 (1621206)
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=37
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
0000:00:1f.1: trying to change BAR0 from 0000 to 01F0
0000:00:1f.1: trying to change BAR1 from 0000 to 03F4
0000:00:1f.1: trying to change BAR2 from 0000 to 0170
0000:00:1f.1: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:04:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:06: ioport range 0x290-0x297 has been reserved
pnp: 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved
pnp: 00:07: iomem range 0xfed50000-0xfed8ffff has been reserved
pnp: 00:07: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:0c: iomem range 0xf0000000-0xf3ffffff has been reserved
pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0d: iomem range 0xc0000-0xdffff could not be reserved
pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
  IO window: c000-cfff
  MEM window: faa00000-feafffff
  PREFETCH window: cff00000-efefffff
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: cfe00000-cfefffff
PCI: Bridge: 0000:00:1c.5
  IO window: b000-bfff
  MEM window: fa900000-fa9fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: a000-afff
  MEM window: fa800000-fa8fffff
  PREFETCH window: c7e00000-cfdfffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 4594k freed
audit: initializing netlink socket (disabled)
audit(1175440901.832:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
Freeing unused kernel memory: 212k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI Warning (tbutils-0158): Incorrect checksum in table [OEMB] -  DB, should be DA [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._OSC] (Node c20f5888), AE_ALREADY_EXISTS
ACPI: Marking method _OSC as Serialized
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._PDC] (Node c20f589c), AE_ALREADY_EXISTS
ACPI: Marking method _PDC as Serialized
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._OSC] (Node c20f57d4), AE_ALREADY_EXISTS
ACPI: Marking method _OSC as Serialized
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._PDC] (Node c20f57e8), AE_ALREADY_EXISTS
ACPI: Marking method _PDC as Serialized
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000e480
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.20 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000e880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 20, io base 0x0000ec00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
JMB363: IDE controller at PCI slot 0000:02:00.1
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 16 (level, low) -> IRQ 16
JMB363: chipset revision 2
JMB363: 100% native mode on irq 16
    ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usb 1-2: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
hda: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
usb 3-2: new full speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 4 ports detected
usb 4-1: new full speed USB device using uhci_hcd and address 2
ide0 at 0xbc00-0xbc07,0xb882 on irq 16
Probing IDE interface ide1...
usb 4-1: configuration #1 chosen from 1 choice
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 4 ports detected
usb 3-2.3: new low speed USB device using uhci_hcd and address 4
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 3-2.3: configuration #1 chosen from 1 choice
usb 3-2.3: can't set config #1, error -71
hub 3-2:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 3-2:1.0: hub_port_status failed (err = -71)
usb 4-1: USB disconnect, address 2
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low) -> IRQ 21
e1000: 0000:01:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:3e:c3:48
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:01:01.2[B] -> GSI 23 (level, low) -> IRQ 22
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]  MMIO=[fa89f800-fa89ffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[21]  MMIO=[fa89f000-fa89f7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ahci 0000:00:1f.2: version 2.1
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 22
usb 5-6: new high speed USB device using ehci_hcd and address 4
usb 5-6: configuration #1 chosen from 1 choice
hub 5-6:1.0: USB hub found
hub 5-6:1.0: 4 ports detected
usb 5-7: new high speed USB device using ehci_hcd and address 5
usb 5-7: configuration #1 chosen from 1 choice
hub 5-7:1.0: USB hub found
hub 5-7:1.0: 4 ports detected
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
ata1: SATA max UDMA/133 cmd 0xf8854900 ctl 0x00000000 bmdma 0x00000000 irq 220
ata2: SATA max UDMA/133 cmd 0xf8854980 ctl 0x00000000 bmdma 0x00000000 irq 220
ata3: SATA max UDMA/133 cmd 0xf8854a00 ctl 0x00000000 bmdma 0x00000000 irq 220
ata4: SATA max UDMA/133 cmd 0xf8854a80 ctl 0x00000000 bmdma 0x00000000 irq 220
scsi0 : ahci
usb 3-1: USB disconnect, address 2
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c0151100d55]
usb 3-1: new full speed USB device using uhci_hcd and address 5
ata1: SATA link down (SStatus 0 SControl 300)
scsi1 : ahci
usb 3-1: configuration #1 chosen from 1 choice
usb 3-2: USB disconnect, address 3
usb 3-2.3: USB disconnect, address 4
ieee1394: Host added: ID:BUS[1-00:1023]  GUID[0011d80000fee27c]
usb 1-2: USB disconnect, address 2
usb 1-2: new low speed USB device using uhci_hcd and address 3
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
scsi2 : ahci
usb 1-2: configuration #1 chosen from 1 choice
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
usb 5-6.3: new low speed USB device using ehci_hcd and address 6
usb 5-6.3: configuration #1 chosen from 1 choice
ata4: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
usb 5-7.3: new high speed USB device using ehci_hcd and address 7
usb 5-7.3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-2
input: Logitech Logitech RumblePad 2 USB as /class/input/input2
input: USB HID v1.10 Joystick [Logitech Logitech RumblePad 2 USB] on usb-0000:00:1d.7-6.3
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PCI: Setting latency timer of device 0000:02:00.0 to 64
ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
ata5: SATA max UDMA/133 cmd 0xf89f0100 ctl 0x00000000 bmdma 0x00000000 irq 17
ata6: SATA max UDMA/133 cmd 0xf89f0180 ctl 0x00000000 bmdma 0x00000000 irq 17
scsi4 : ahci
ata5: SATA link down (SStatus 0 SControl 300)
scsi5 : ahci
ata6: SATA link down (SStatus 0 SControl 300)
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 23
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
    ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hde:DMA, hdf:DMA
    ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: ST3250823A, ATA DISK drive
hdf: IC35L120AVV207-0, ATA DISK drive
ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide3...
hde: max request size: 512KiB
hde: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hde: cache flushes supported
 hde:<6>hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
 hde1 hde2 hde3 hde4 < hde5 >
hdf: max request size: 512KiB
hdf: 241254720 sectors (123522 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
hdf: cache flushes supported
 hdf: hdf1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input3
Real Time Clock Driver v1.12ac
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 22
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0317
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
gameport: EMU10K1 is pci0000:01:01.1/gameport0, io 0xac00, speed 1028kHz
ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 23
Installing spdif_bug patch: Audigy 2 ZS [SB0350]
EXT3 FS on hde2, internal journal
Probing IDE interface ide1...
Probing IDE interface ide3...
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
eth0: no IPv6 routers present

[-- Attachment #1.3: 2.6.20-rc5_sata.txt --]
[-- Type: text/plain, Size: 24794 bytes --]

Linux version 2.6.21-rc5 (hawk@janne) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP PREEMPT Sun Apr 1 14:54:51 CEST 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000007fe80000 end: 000000007ff80000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000007ff80000 size: 000000000000e000 end: 000000007ff8e000 type: 3
copy_e820_map() start: 000000007ff8e000 size: 0000000000052000 end: 000000007ffe0000 type: 4
copy_e820_map() start: 000000007ffe0000 size: 0000000000020000 end: 0000000080000000 type: 2
copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end: 0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ff80000 (usable)
 BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data)
 BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
 BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 524160) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   524160
early_node_map[1] active PFN ranges
    0:        0 ->   524160
On node 0 totalpages: 524160
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 2303 pages used for memmap
  HighMem zone: 292481 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP 000FAF20, 0014 (r0 ACPIAM)
ACPI: RSDT 7FF80000, 0044 (r1 NEC              3000707 MSFT       97)
ACPI: FACP 7FF80200, 0081 (r1 A_M_I_ OEMFACP   3000707 MSFT       97)
ACPI: DSDT 7FF80590, 9560 (r1  A0543 A0543000        0 INTL 20060113)
ACPI: FACS 7FF8E000, 0040
ACPI: APIC 7FF80390, 0080 (r1 A_M_I_ OEMAPIC   3000707 MSFT       97)
ACPI: SLIC 7FF80410, 0176 (r1 NEC              3000707 MSFT       97)
ACPI: OEMB 7FF8E040, 0066 (r1 A_M_I_ AMI_OEM   3000707 MSFT       97)
ACPI: HPET 7FF89AF0, 0038 (r1 A_M_I_ OEMHPET   3000707 MSFT       97)
ACPI: MCFG 7FF89B30, 003C (r1 A_M_I_ OEMMCFG   3000707 MSFT       97)
ACPI: SSDT 7FF8E0B0, 01C6 (r1    AMI   CPU1PM        1 INTL 20060113)
ACPI: SSDT 7FF8E280, 013A (r1    AMI   CPU2PM        1 INTL 20060113)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000)
Built 1 zonelists.  Total pages: 520065
Kernel command line: root=/dev/hde2 ro irqpoll
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2404.249 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070604k/2096640k available (1679k kernel code, 24756k reserved, 668k data, 212k init, 1179136k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4f000 - 0xfffff000   ( 704 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc0351000 - 0xc0386000   ( 212 kB)
      .data : 0xc02a3c5d - 0xc034af74   ( 668 kB)
      .text : 0xc0100000 - 0xc02a3c5d   (1679 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Calibrating delay using timer specific routine.. 4818.55 BogoMIPS (lpj=9637112)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4808.24 BogoMIPS (lpj=9616482)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz stepping 06
Total of 2 processors activated (9626.79 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
APIC calibration not consistent with PM Timer: 96ms instead of 100ms
APIC delta adjusted to PM-Timer: 1669519 (1618826)
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=27
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
0000:00:1f.1: trying to change BAR0 from 0000 to 01F0
0000:00:1f.1: trying to change BAR1 from 0000 to 03F4
0000:00:1f.1: trying to change BAR2 from 0000 to 0170
0000:00:1f.1: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:04:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:06: ioport range 0x290-0x297 has been reserved
pnp: 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved
pnp: 00:07: iomem range 0xfed50000-0xfed8ffff has been reserved
pnp: 00:07: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:0c: iomem range 0xf0000000-0xf3ffffff has been reserved
pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0d: iomem range 0xc0000-0xdffff could not be reserved
pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
  IO window: c000-cfff
  MEM window: faa00000-feafffff
  PREFETCH window: cff00000-efefffff
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: cfe00000-cfefffff
PCI: Bridge: 0000:00:1c.5
  IO window: b000-bfff
  MEM window: fa900000-fa9fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: a000-afff
  MEM window: fa800000-fa8fffff
  PREFETCH window: c7e00000-cfdfffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 4594k freed
audit: initializing netlink socket (disabled)
audit(1175442775.832:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
Freeing unused kernel memory: 212k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI Warning (tbutils-0158): Incorrect checksum in table [OEMB] -  DB, should be DA [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._OSC] (Node c20f5888), AE_ALREADY_EXISTS
ACPI: Marking method _OSC as Serialized
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._PDC] (Node c20f589c), AE_ALREADY_EXISTS
ACPI: Marking method _PDC as Serialized
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._OSC] (Node c20f57d4), AE_ALREADY_EXISTS
ACPI: Marking method _OSC as Serialized
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._PDC] (Node c20f57e8), AE_ALREADY_EXISTS
ACPI: Marking method _PDC as Serialized
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
JMB363: IDE controller at PCI slot 0000:02:00.1
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 16 (level, low) -> IRQ 16
JMB363: chipset revision 2
JMB363: 100% native mode on irq 16
    ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
SCSI subsystem initialized
usbcore: registered new device driver usb
libata version 2.20 loaded.
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
USB Universal Host Controller Interface driver v3.0
ieee1394: Initialized config rom entry `ip1394'
hda: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
ide0 at 0xbc00-0xbc07,0xb882 on irq 16
Probing IDE interface ide1...
ahci 0000:00:1f.2: version 2.1
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
ata1: SATA max UDMA/133 cmd 0xf8850900 ctl 0x00000000 bmdma 0x00000000 irq 220
ata2: SATA max UDMA/133 cmd 0xf8850980 ctl 0x00000000 bmdma 0x00000000 irq 220
ata3: SATA max UDMA/133 cmd 0xf8850a00 ctl 0x00000000 bmdma 0x00000000 irq 220
ata4: SATA max UDMA/133 cmd 0xf8850a80 ctl 0x00000000 bmdma 0x00000000 irq 220
scsi0 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-4: ST320430A, 3.11, max UDMA/33
ata1.00: 40079088 sectors, multi 16: LBA 
ata1.00: applying bridge limits
ata1.00: configured for UDMA/33
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: port failed to respond (30 secs, Status 0x80)
ata2: COMRESET failed (device not ready)
ata2: hardreset failed, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-6: Config  Disk, RGL10364, max UDMA/133
ata2.00: 640 sectors, multi 1: LBA 
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST320430A        3.11 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access     ATA      Config  Disk     RGL1 PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
ata5: SATA max UDMA/133 cmd 0xf8910100 ctl 0x00000000 bmdma 0x00000000 irq 17
ata6: SATA max UDMA/133 cmd 0xf8910180 ctl 0x00000000 bmdma 0x00000000 irq 17
scsi4 : ahci
ata5: SATA link down (SStatus 0 SControl 300)
scsi5 : ahci
ata6: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low) -> IRQ 19
SCSI device sda: 40079088 512-byte hdwr sectors (20520 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 40079088 512-byte hdwr sectors (20520 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 >
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 640 512-byte hdwr sectors (0 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 640 512-byte hdwr sectors (0 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sdb: unknown partition table
sd 1:0:0:0: Attached scsi disk sdb
e1000: 0000:01:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:3e:c3:48
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 20
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
    ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hde:DMA, hdf:DMA
    ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: ST3250823A, ATA DISK drive
hdf: IC35L120AVV207-0, ATA DISK drive
ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide3...
ACPI: PCI Interrupt 0000:01:01.2[B] -> GSI 23 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[fa89f800-fa89ffff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 19
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[fa89f000-fa89f7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000e480
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000e880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ec00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hde: max request size: 512KiB
hde: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hde: cache flushes supported
 hde: hde1 hde2 hde3 hde4 < hde5 >
hdf: max request size: 512KiB
hdf: 241254720 sectors (123522 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
hdf: cache flushes supported
 hdf: hdf1
usb 1-2: device not accepting address 2, error -71
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c0151100d55]
ieee1394: Host added: ID:BUS[1-00:1023]  GUID[0011d80000fee27c]
usb 5-6: new high speed USB device using ehci_hcd and address 4
usb 5-6: configuration #1 chosen from 1 choice
hub 5-6:1.0: USB hub found
hub 5-6:1.0: 4 ports detected
usb 5-7: new high speed USB device using ehci_hcd and address 5
usb 5-7: configuration #1 chosen from 1 choice
hub 5-7:1.0: USB hub found
hub 5-7:1.0: 4 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
usb 3-1: new full speed USB device using uhci_hcd and address 2
input: PC Speaker as /class/input/input1
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 18
usb 3-1: configuration #1 chosen from 1 choice
usb 5-6.3: new low speed USB device using ehci_hcd and address 6
intel_rng: FWH not detected
usb 5-6.3: configuration #1 chosen from 1 choice
gameport: EMU10K1 is pci0000:01:01.1/gameport0, io 0xac00, speed 1028kHz
Real Time Clock Driver v1.12ac
usb 5-7.3: new high speed USB device using ehci_hcd and address 7
usb 5-7.3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0317
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-2
input: Logitech Logitech RumblePad 2 USB as /class/input/input3
input: USB HID v1.10 Joystick [Logitech Logitech RumblePad 2 USB] on usb-0000:00:1d.7-6.3
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 20
Installing spdif_bug patch: Audigy 2 ZS [SB0350]
EXT3 FS on hde2, internal journal
Probing IDE interface ide1...
Probing IDE interface ide3...
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS: bad magic number
XFS: SB validate failed
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
eth0: no IPv6 routers present

[-- Attachment #2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 2147 bytes --]

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-14 17:47 ` Bill Davidsen
@ 2007-02-14 21:43   ` Greg Trounson
  0 siblings, 0 replies; 18+ messages in thread
From: Greg Trounson @ 2007-02-14 21:43 UTC (permalink / raw)
  To: Bill Davidsen; +Cc: linux-kernel

Bill Davidsen wrote:
> Greg Trounson wrote:
>> At the risk of sounding like a "me too" post:
>>
>> I also have an Asus P5W-DH, with the following drives connected:
>>
>> SATA: ST3250820AS, connected to sata1
>> PATA: HL-DT-ST GSA-H12N, ATAPI DVD Writer, Primary master
>>
>> On bootup of 2.6.19 and 2.6.20, the kernel stalls for 1 minute when 
>> probing sata2, eventually giving up and continuing the boot process.  
>> There is no physical sata2 connector on the Motherboard, just solder 
>> lugs between sata1 and sata3.  From other users I understand this is 
>> really a Silicon Image SIL4723 SATA to 2-Port SATA splitter.  It is 
>> detected by the kernel as a disk, as below.
>>
>> The relevant part of the boot process looks like:
>> ...
>> libata version 2.00 loaded.
>> ahci 0000:00:1f.2: version 2.0
>> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 22
>> PCI: Setting latency timer of device 0000:00:1f.2 to 64
>> ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl 
>> SATA mode
>> ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
>> ata1: SATA max UDMA/133 cmd 0xF882A900 ctl 0x0 bmdma 0x0 irq 219
>> ata2: SATA max UDMA/133 cmd 0xF882A980 ctl 0x0 bmdma 0x0 irq 219
>> ata3: SATA max UDMA/133 cmd 0xF882AA00 ctl 0x0 bmdma 0x0 irq 219
>> ata4: SATA max UDMA/133 cmd 0xF882AA80 ctl 0x0 bmdma 0x0 irq 219
>> scsi0 : ahci
>> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
>> ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
>> ata1.00: ata1: dev 0 multi count 16
>> ata1.00: configured for UDMA/133
>> scsi1 : ahci
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>>
>> ...waits 20 seconds...
>>
>> ata2.00: qc timeout (cmd 0xec)
>> ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
>>
>> ...waits 5 seconds...
>>
>> ata2: port is slow to respond, please be patient (Status 0x80)
>>
>> ...waits 30 seconds...
>>
>> ata2: port failed to respond (30 secs, Status 0x80)
>> ata2: COMRESET failed (device not ready)
>> ata2: hardreset failed, retrying in 5 secs
>>
>> ...waits 5 seconds...
>>
>> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
>> ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA
>> ata2.00: ata2: dev 0 multi count 1
>> ata2.00: configured for UDMA/133
>> scsi2 : ahci
>> ata3: SATA link down (SStatus 0 SControl 300)
>> ...
>>
>> A bit of poking about shows:
>>
>> fdisk -l /dev/sdb
>> Disk /dev/sdb: 0 MB, 327680 bytes
>> 255 heads, 63 sectors/track, 0 cylinders
>> Units = cylinders of 16065 * 512 = 8225280 bytes
>> Disk /dev/sdb doesn't contain a valid partition table
>>
>> So it presents itself as a 320k disk, filled with zeroes as below:
>>
>> dd if=/dev/sdb |hexdump
>> 0000000 0000 0000 0000 0000 0000 0000 0000 0000
>> *
>> 0050000
>>
>> 640+0 records in
>> 640+0 records out
>> 327680 bytes (328 kB) copied, 0.0106662 seconds, 30.7 MB/s
>>
...
> Is this 320k of cache memory, or in any way some actual storage on the 
> system? Have you tried to write to it out of curiosity? Seems odd that 
> it would be detected if there were nothing at all present, although 
> obviously it could be artifact.

According to the product outline at 
http://www.siliconimage.com/products/product.aspx?id=64, the Silicon Image port multiplier 
has an EEPROM of unspecified size.

With the drive appearing as precisely 320K I wouldn't be surprised if this EEPROM is what 
it was seeing.  Even though it's currently filled with zeros I dare not write to it 
through fear of bricking the controller.

Greg




^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-14  0:56 Greg Trounson
@ 2007-02-14 17:47 ` Bill Davidsen
  2007-02-14 21:43   ` Greg Trounson
  2007-04-01 14:19 ` Håkan Lindqvist
  1 sibling, 1 reply; 18+ messages in thread
From: Bill Davidsen @ 2007-02-14 17:47 UTC (permalink / raw)
  To: Greg Trounson; +Cc: linux-kernel

Greg Trounson wrote:
> At the risk of sounding like a "me too" post:
> 
> I also have an Asus P5W-DH, with the following drives connected:
> 
> SATA: ST3250820AS, connected to sata1
> PATA: HL-DT-ST GSA-H12N, ATAPI DVD Writer, Primary master
> 
> On bootup of 2.6.19 and 2.6.20, the kernel stalls for 1 minute when 
> probing sata2, eventually giving up and continuing the boot process.  
> There is no physical sata2 connector on the Motherboard, just solder 
> lugs between sata1 and sata3.  From other users I understand this is 
> really a Silicon Image SIL4723 SATA to 2-Port SATA splitter.  It is 
> detected by the kernel as a disk, as below.
> 
> The relevant part of the boot process looks like:
> ...
> libata version 2.00 loaded.
> ahci 0000:00:1f.2: version 2.0
> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 22
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA 
> mode
> ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
> ata1: SATA max UDMA/133 cmd 0xF882A900 ctl 0x0 bmdma 0x0 irq 219
> ata2: SATA max UDMA/133 cmd 0xF882A980 ctl 0x0 bmdma 0x0 irq 219
> ata3: SATA max UDMA/133 cmd 0xF882AA00 ctl 0x0 bmdma 0x0 irq 219
> ata4: SATA max UDMA/133 cmd 0xF882AA80 ctl 0x0 bmdma 0x0 irq 219
> scsi0 : ahci
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
> ata1.00: ata1: dev 0 multi count 16
> ata1.00: configured for UDMA/133
> scsi1 : ahci
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> 
> ...waits 20 seconds...
> 
> ata2.00: qc timeout (cmd 0xec)
> ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
> 
> ...waits 5 seconds...
> 
> ata2: port is slow to respond, please be patient (Status 0x80)
> 
> ...waits 30 seconds...
> 
> ata2: port failed to respond (30 secs, Status 0x80)
> ata2: COMRESET failed (device not ready)
> ata2: hardreset failed, retrying in 5 secs
> 
> ...waits 5 seconds...
> 
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA
> ata2.00: ata2: dev 0 multi count 1
> ata2.00: configured for UDMA/133
> scsi2 : ahci
> ata3: SATA link down (SStatus 0 SControl 300)
> ...
> 
> A bit of poking about shows:
> 
> fdisk -l /dev/sdb
> Disk /dev/sdb: 0 MB, 327680 bytes
> 255 heads, 63 sectors/track, 0 cylinders
> Units = cylinders of 16065 * 512 = 8225280 bytes
> Disk /dev/sdb doesn't contain a valid partition table
> 
> So it presents itself as a 320k disk, filled with zeroes as below:
> 
> dd if=/dev/sdb |hexdump
> 0000000 0000 0000 0000 0000 0000 0000 0000 0000
> *
> 0050000
> 
> 640+0 records in
> 640+0 records out
> 327680 bytes (328 kB) copied, 0.0106662 seconds, 30.7 MB/s
> 
> Note that this is not a fatal error.  The machine still boots 
> eventually, but the seemingly mandatory 60 second pause makes startup 
> rather cumbersome for the user.
> 
> So far none of the suggested fixes have managed to stop ata2 from being 
> detected. (noprobe=ata2, irqpoll, etc).  I understand this problem 
> wasn't present in 2.6.16 so the problem must lie in some patch since 
> then.  I see Tejun is working towards patches for this and I would be 
> happy to try them here.
> 
Is this 320k of cache memory, or in any way some actual storage on the 
system? Have you tried to write to it out of curiosity? Seems odd that 
it would be detected if there were nothing at all present, although 
obviously it could be artifact.

-- 
Bill Davidsen <davidsen@tmr.com>
   "We have more to fear from the bungling of the incompetent than from
the machinations of the wicked."  - from Slashdot

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
@ 2007-02-14  0:56 Greg Trounson
  2007-02-14 17:47 ` Bill Davidsen
  2007-04-01 14:19 ` Håkan Lindqvist
  0 siblings, 2 replies; 18+ messages in thread
From: Greg Trounson @ 2007-02-14  0:56 UTC (permalink / raw)
  To: linux-kernel

At the risk of sounding like a "me too" post:

I also have an Asus P5W-DH, with the following drives connected:

SATA: ST3250820AS, connected to sata1
PATA: HL-DT-ST GSA-H12N, ATAPI DVD Writer, Primary master

On bootup of 2.6.19 and 2.6.20, the kernel stalls for 1 minute when probing sata2, 
eventually giving up and continuing the boot process.  There is no physical sata2 
connector on the Motherboard, just solder lugs between sata1 and sata3.  From other users 
I understand this is really a Silicon Image SIL4723 SATA to 2-Port SATA splitter.  It is 
detected by the kernel as a disk, as below.

The relevant part of the boot process looks like:
...
libata version 2.00 loaded.
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xF882A900 ctl 0x0 bmdma 0x0 irq 219
ata2: SATA max UDMA/133 cmd 0xF882A980 ctl 0x0 bmdma 0x0 irq 219
ata3: SATA max UDMA/133 cmd 0xF882AA00 ctl 0x0 bmdma 0x0 irq 219
ata4: SATA max UDMA/133 cmd 0xF882AA80 ctl 0x0 bmdma 0x0 irq 219
scsi0 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

...waits 20 seconds...

ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)

...waits 5 seconds...

ata2: port is slow to respond, please be patient (Status 0x80)

...waits 30 seconds...

ata2: port failed to respond (30 secs, Status 0x80)
ata2: COMRESET failed (device not ready)
ata2: hardreset failed, retrying in 5 secs

...waits 5 seconds...

ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA
ata2.00: ata2: dev 0 multi count 1
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
...

A bit of poking about shows:

fdisk -l /dev/sdb
Disk /dev/sdb: 0 MB, 327680 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/sdb doesn't contain a valid partition table

So it presents itself as a 320k disk, filled with zeroes as below:

dd if=/dev/sdb |hexdump
0000000 0000 0000 0000 0000 0000 0000 0000 0000
*
0050000

640+0 records in
640+0 records out
327680 bytes (328 kB) copied, 0.0106662 seconds, 30.7 MB/s

Note that this is not a fatal error.  The machine still boots eventually, but the 
seemingly mandatory 60 second pause makes startup rather cumbersome for the user.

So far none of the suggested fixes have managed to stop ata2 from being detected. 
(noprobe=ata2, irqpoll, etc).  I understand this problem wasn't present in 2.6.16 so the 
problem must lie in some patch since then.  I see Tejun is working towards patches for 
this and I would be happy to try them here.

thanks,
Greg




^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-13  7:33                     ` Paul Rolland
@ 2007-02-13 20:20                       ` Tejun Heo
  0 siblings, 0 replies; 18+ messages in thread
From: Tejun Heo @ 2007-02-13 20:20 UTC (permalink / raw)
  To: rol
  Cc: 'Alan', 'Robert Hancock',
	'Linux Kernel Mailing List'

Hello, Paul.

Paul Rolland wrote:
> Also, please note that libata is complaining :
> ATA: abnormal status 0x7F on port 0x177
> and later :
> ATA: abnormal status 0x7F on port 0x9807

You can ignore the above.  The errors on ata2 are due to SIMG storage 
processor and will probably fixed when PMP support is implemented.  The 
latter errors on pata_jmicron is probably due to lack of proper mode 
programming on that driver.  I'll look into that.

Thanks.

-- 
tejun

^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-12 11:19                   ` Paul Rolland
@ 2007-02-13  7:33                     ` Paul Rolland
  2007-02-13 20:20                       ` Tejun Heo
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-13  7:33 UTC (permalink / raw)
  To: rol, 'Tejun Heo'
  Cc: 'Alan', 'Robert Hancock',
	'Linux Kernel Mailing List'

[-- Attachment #1: Type: text/plain, Size: 4376 bytes --]

Hello Tejun,

I've tested your patch yesterday, but no luck, I can't find any difference
in the resulting boot log.

Please find attached an archive containing :
 - dmesg.2.6.20-rc7 : full dmesg with stock kernel
 - dmesg.patch : full dmesg with your patch included.

I've also added a lspci -vvv, a cat /proc/interrupts and a cat /proc/ioports
in case this could help.

Also, please note that libata is complaining :
ATA: abnormal status 0x7F on port 0x177
and later :
ATA: abnormal status 0x7F on port 0x9807

I don't know if this is important or not.

Sorry for the bad news, 
Regards,
Paul

Paul Rolland, rol(at)as2917.net
ex-AS2917 Network administrator and Peering Coordinator

--

Please no HTML, I'm not a browser - Pas d'HTML, je ne suis pas un navigateur 
"Some people dream of success... while others wake up and work hard at it" 

"I worry about my child and the Internet all the time, even though she's too 
young to have logged on yet. Here's what I worry about. I worry that 10 or 15 
years from now, she will come to me and say 'Daddy, where were you when they 
took freedom of the press away from the Internet?'"
--Mike Godwin, Electronic Frontier Foundation 
  

> -----Original Message-----
> From: linux-kernel-owner@vger.kernel.org 
> [mailto:linux-kernel-owner@vger.kernel.org] On Behalf Of Paul Rolland
> Sent: Monday, February 12, 2007 12:19 PM
> To: 'Tejun Heo'
> Cc: 'Alan'; 'Robert Hancock'; 'Linux Kernel Mailing List'
> Subject: RE: AHCI - remove probing of ata2
> 
> Hello Tejun,
> 
> > You have a Maxtor connected to that port, right?  That's caused by 
> 
> Waoh, you are using crystal ball ? :) You are right, this is a Maxtor
> disk, 250 MB. If you want more details about this disk, I can send you
> a complete details.
> 
> > firmware bug.  Future kernels will consider that condition as 
> > protocol 
> > violation and blacklist the drive such that NCQ is not used 
> on it.  I 
> > think it can be dangerous on rare corner/error cases but 
> there hasn't 
> > been any actual report of problems caused by that, so no need 
> > to worry 
> > about it too much.  If it bothers you, you can turn NCQ off 
> > using sysfs 
> > node.  Take a look at FAQ section of http://linux-ata.org
> 
> I'm just slightly worried about that, and because all this libata
> stuff is quite "new", I prefer to report everything I can 
> see, considering
> that I can test patches on this machine if people need me to do so.
> So, consider this machine as some kind of playground if you have
> some code you want someone to test.
>  
> > Slightly OT, but it's generally a good idea to use LABELs to access 
> > filesystems.  With so many ports and EH dynamics including 
> > hotplug, it's 
> > much more difficult to keep device names persistent and 
> remember them.
> 
> Yes, that's what I should do, but I've never really like that stuff ;(
>  
> > > So, 2.6.20-rc7 results are :
> > >  - ata2 probing still very long and delaying boot a lot,
> > 
> > That's sil4726's config device acting weird.  When reset as 
> a normal 
> > device (not PMP device), sil4726 acts as a normal ATA 
> device which is 
> > used to configure how the chip behaves.  Unfortunately, the 
> emulation 
> > seems to contain some flaws and cause lots of delays as 
> you've seen. 
> > I'm attaching a patch to clear TF before IDENTIFY which 
> fixes similar 
> > IDENTIFY failures on buggy ATAPI devices.
> 
> OK, will try this tonite (I'm sorry, this is my home comp., 
> and I'm at the
> office right now - will tell you tomorrow).
>  
> > >  - Jmicron PATA still not working, and doesn't even detect 
> > the DVD-ROM on
> > >    the port.
> > 
> > This problem is likely to be fixed by clearing TF before IDENTIFY.
> > 
> > So, please test the attached patch and report the result.
> 
> Will do, and will test more if you more that are to be tested !
> 
> BTW, maybe OT, but what about setting a list of people willing to test
> patches together with their configurations so that they can be send
> patches related to their hardware ? That could be useful to 
> people developing
> drivers...
> 
> Regards,
> Paul
> 
> -
> To unsubscribe from this list: send the line "unsubscribe 
> linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 

[-- Attachment #2: data.tar.bz2 --]
[-- Type: application/octet-stream, Size: 13391 bytes --]

^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-12  0:53                 ` Tejun Heo
@ 2007-02-12 11:19                   ` Paul Rolland
  2007-02-13  7:33                     ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-12 11:19 UTC (permalink / raw)
  To: 'Tejun Heo'
  Cc: 'Alan', 'Robert Hancock',
	'Linux Kernel Mailing List'

Hello Tejun,

> You have a Maxtor connected to that port, right?  That's caused by 

Waoh, you are using crystal ball ? :) You are right, this is a Maxtor
disk, 250 MB. If you want more details about this disk, I can send you
a complete details.

> firmware bug.  Future kernels will consider that condition as 
> protocol 
> violation and blacklist the drive such that NCQ is not used on it.  I 
> think it can be dangerous on rare corner/error cases but there hasn't 
> been any actual report of problems caused by that, so no need 
> to worry 
> about it too much.  If it bothers you, you can turn NCQ off 
> using sysfs 
> node.  Take a look at FAQ section of http://linux-ata.org

I'm just slightly worried about that, and because all this libata
stuff is quite "new", I prefer to report everything I can see, considering
that I can test patches on this machine if people need me to do so.
So, consider this machine as some kind of playground if you have
some code you want someone to test.
 
> Slightly OT, but it's generally a good idea to use LABELs to access 
> filesystems.  With so many ports and EH dynamics including 
> hotplug, it's 
> much more difficult to keep device names persistent and remember them.

Yes, that's what I should do, but I've never really like that stuff ;(
 
> > So, 2.6.20-rc7 results are :
> >  - ata2 probing still very long and delaying boot a lot,
> 
> That's sil4726's config device acting weird.  When reset as a normal 
> device (not PMP device), sil4726 acts as a normal ATA device which is 
> used to configure how the chip behaves.  Unfortunately, the emulation 
> seems to contain some flaws and cause lots of delays as you've seen. 
> I'm attaching a patch to clear TF before IDENTIFY which fixes similar 
> IDENTIFY failures on buggy ATAPI devices.

OK, will try this tonite (I'm sorry, this is my home comp., and I'm at the
office right now - will tell you tomorrow).
 
> >  - Jmicron PATA still not working, and doesn't even detect 
> the DVD-ROM on
> >    the port.
> 
> This problem is likely to be fixed by clearing TF before IDENTIFY.
> 
> So, please test the attached patch and report the result.

Will do, and will test more if you more that are to be tested !

BTW, maybe OT, but what about setting a list of people willing to test
patches together with their configurations so that they can be send
patches related to their hardware ? That could be useful to people developing
drivers...

Regards,
Paul


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-11 10:17               ` Paul Rolland
@ 2007-02-12  0:53                 ` Tejun Heo
  2007-02-12 11:19                   ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Tejun Heo @ 2007-02-12  0:53 UTC (permalink / raw)
  To: rol
  Cc: 'Alan', 'Robert Hancock',
	'Linux Kernel Mailing List'

[-- Attachment #1: Type: text/plain, Size: 2151 bytes --]

Hello, Paul.

Paul Rolland wrote:
>>> This looks like the problems that hopefully the patches 
>> from Tejun and
>>> from Mark Lord cured (the delay after reset and the task file clear)
>> Any chance I can find this patch(es) and try them ?
>>  
>>>> Also, I've seen a :
>>>>
>>>> ata1: Spurious SDB FIS during NCQ issue=0x0 SAct=0x7ff8001f
>>>> FIS=004040a1:00040000
>>>>
>>>> What's this ? Is it really bad or just a warning ???
>>> It's one Tejun stuck logging in for in order to investigate further.
>> OK, will wait a little bit ;)

You have a Maxtor connected to that port, right?  That's caused by 
firmware bug.  Future kernels will consider that condition as protocol 
violation and blacklist the drive such that NCQ is not used on it.  I 
think it can be dangerous on rare corner/error cases but there hasn't 
been any actual report of problems caused by that, so no need to worry 
about it too much.  If it bothers you, you can turn NCQ off using sysfs 
node.  Take a look at FAQ section of http://linux-ata.org

> In the meantime, I've been trying 2.6.20-rc7.
> Things are not better, except that the ata2 probing failing results in
> no /dev/sdd being allocated, thus it changes all the naming afterwards.

Slightly OT, but it's generally a good idea to use LABELs to access 
filesystems.  With so many ports and EH dynamics including hotplug, it's 
much more difficult to keep device names persistent and remember them.

> So, 2.6.20-rc7 results are :
>  - ata2 probing still very long and delaying boot a lot,

That's sil4726's config device acting weird.  When reset as a normal 
device (not PMP device), sil4726 acts as a normal ATA device which is 
used to configure how the chip behaves.  Unfortunately, the emulation 
seems to contain some flaws and cause lots of delays as you've seen. 
I'm attaching a patch to clear TF before IDENTIFY which fixes similar 
IDENTIFY failures on buggy ATAPI devices.

>  - Jmicron PATA still not working, and doesn't even detect the DVD-ROM on
>    the port.

This problem is likely to be fixed by clearing TF before IDENTIFY.

So, please test the attached patch and report the result.

-- 
tejun

[-- Attachment #2: clear-TF-before-IDENTIFY.patch --]
[-- Type: text/x-patch, Size: 780 bytes --]

diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 667acd2..d6fcf0a 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1478,7 +1478,16 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
 	}
 
 	tf.protocol = ATA_PROT_PIO;
-	tf.flags |= ATA_TFLAG_POLLING; /* for polling presence detection */
+
+	/* Some devices choke if TF registers contain garbage.  Make
+	 * sure those are properly initialized.
+	 */
+	tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
+
+	/* Device presence detection is unreliable on some
+	 * controllers.  Always poll IDENTIFY if available.
+	 */
+	tf.flags |= ATA_TFLAG_POLLING;
 
 	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
 				     id, sizeof(id[0]) * ATA_ID_WORDS);

^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-10 21:59             ` Paul Rolland
@ 2007-02-11 10:17               ` Paul Rolland
  2007-02-12  0:53                 ` Tejun Heo
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-11 10:17 UTC (permalink / raw)
  To: rol, 'Alan'
  Cc: 'Robert Hancock', 'Linux Kernel Mailing List'

> > This looks like the problems that hopefully the patches 
> from Tejun and
> > from Mark Lord cured (the delay after reset and the task file clear)
> 
> Any chance I can find this patch(es) and try them ?
>  
> > > Also, I've seen a :
> > > 
> > > ata1: Spurious SDB FIS during NCQ issue=0x0 SAct=0x7ff8001f
> > > FIS=004040a1:00040000
> > > 
> > > What's this ? Is it really bad or just a warning ???
> > 
> > It's one Tejun stuck logging in for in order to investigate further.
> 
> OK, will wait a little bit ;)
> 

In the meantime, I've been trying 2.6.20-rc7.
Things are not better, except that the ata2 probing failing results in
no /dev/sdd being allocated, thus it changes all the naming afterwards.

So, 2.6.20-rc7 results are :
 - ata2 probing still very long and delaying boot a lot,
 - Jmicron PATA still not working, and doesn't even detect the DVD-ROM on
   the port.

Guys, should you have any patch that you'd like me to test, feel free to
send, I'll do that more than happily.

Regards,
Paul


^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-10 20:36           ` Alan
@ 2007-02-10 21:59             ` Paul Rolland
  2007-02-11 10:17               ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-10 21:59 UTC (permalink / raw)
  To: 'Alan'
  Cc: 'Robert Hancock', 'Linux Kernel Mailing List'

Hello,

> This looks like the problems that hopefully the patches from Tejun and
> from Mark Lord cured (the delay after reset and the task file clear)

Any chance I can find this patch(es) and try them ?
 
> > Also, I've seen a :
> > 
> > ata1: Spurious SDB FIS during NCQ issue=0x0 SAct=0x7ff8001f
> > FIS=004040a1:00040000
> > 
> > What's this ? Is it really bad or just a warning ???
> 
> It's one Tejun stuck logging in for in order to investigate further.

OK, will wait a little bit ;)

Regards,
Paul


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-10 20:01         ` Paul Rolland
@ 2007-02-10 20:36           ` Alan
  2007-02-10 21:59             ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Alan @ 2007-02-10 20:36 UTC (permalink / raw)
  To: rol; +Cc: 'Robert Hancock', 'Linux Kernel Mailing List'

> OK, rebooting again, with a new root device as /dev/sde1...
> No problem for the old IDE devices, they are now /dev/sdX.
> 
> But the Jmicron stuff is still broken though no more conflict :(

Thanks. That helps a lot as it narrows it down

> 
> PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
> ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 16 (level, low) -> IRQ 16
> ata7: PATA max UDMA/100 cmd 0x9C00 ctl 0x9882 bmdma 0x9400 irq 16
> ata8: PATA max UDMA/100 cmd 0x9800 ctl 0x9482 bmdma 0x9408 irq 16
> scsi6 : pata_jmicron
> ata7.00: ATAPI, max UDMA/66
> ata7.00: qc timeout (cmd 0xef)
> ata7.00: failed to set xfermode (err_mask=0x4)
> ata7.00: limiting speed to UDMA/44
> ata7: failed to recover some devices, retrying in 5 secs
> ata7.00: qc timeout (cmd 0xef)
> ata7.00: failed to set xfermode (err_mask=0x4)
> ata7.00: limiting speed to PIO0
> ata7: failed to recover some devices, retrying in 5 secs
> ata7.00: qc timeout (cmd 0xef)
> ata7.00: failed to set xfermode (err_mask=0x4)
> ata7.00: disabled
> scsi7 : pata_jmicron
> ATA: abnormal status 0x7F on port 0x9807

This looks like the problems that hopefully the patches from Tejun and
from Mark Lord cured (the delay after reset and the task file clear)

> Also, I've seen a :
> 
> ata1: Spurious SDB FIS during NCQ issue=0x0 SAct=0x7ff8001f
> FIS=004040a1:00040000
> 
> What's this ? Is it really bad or just a warning ???

It's one Tejun stuck logging in for in order to investigate further.

Alan

^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-10 19:06       ` Alan
@ 2007-02-10 20:01         ` Paul Rolland
  2007-02-10 20:36           ` Alan
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-10 20:01 UTC (permalink / raw)
  To: 'Alan'
  Cc: 'Robert Hancock', 'Linux Kernel Mailing List'

Hi Alan,

> You have the old driver 0n 0x1F0
> 
> 
> > PCI: Device 0000:02:00.0 not available because of resource 
> collisions
> > ahci: probe of 0000:02:00.0 failed with error -22
> > ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
> > ata: 0x1F0 IDE port busy
> 
> And the new drivers trying to manage the same port
> 
> > CONFIG_IDE=y
> > CONFIG_BLK_DEV_IDE=y
> 
> Set those to "N" and try again

Done that, rebuilt and rebooted...
/dev/hda and /dev/hdb (old driver) are gone... 
OK, rebooting again, with a new root device as /dev/sde1...
No problem for the old IDE devices, they are now /dev/sdX.

But the Jmicron stuff is still broken though no more conflict :(

PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 16 (level, low) -> IRQ 16
ata7: PATA max UDMA/100 cmd 0x9C00 ctl 0x9882 bmdma 0x9400 irq 16
ata8: PATA max UDMA/100 cmd 0x9800 ctl 0x9482 bmdma 0x9408 irq 16
scsi6 : pata_jmicron
ata7.00: ATAPI, max UDMA/66
ata7.00: qc timeout (cmd 0xef)
ata7.00: failed to set xfermode (err_mask=0x4)
ata7.00: limiting speed to UDMA/44
ata7: failed to recover some devices, retrying in 5 secs
ata7.00: qc timeout (cmd 0xef)
ata7.00: failed to set xfermode (err_mask=0x4)
ata7.00: limiting speed to PIO0
ata7: failed to recover some devices, retrying in 5 secs
ata7.00: qc timeout (cmd 0xef)
ata7.00: failed to set xfermode (err_mask=0x4)
ata7.00: disabled
scsi7 : pata_jmicron
ATA: abnormal status 0x7F on port 0x9807


Also, I've seen a :

ata1: Spurious SDB FIS during NCQ issue=0x0 SAct=0x7ff8001f
FIS=004040a1:00040000

What's this ? Is it really bad or just a warning ???

Regards,
Paul



^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
  2007-02-10 18:39     ` Paul Rolland
@ 2007-02-10 19:06       ` Alan
  2007-02-10 20:01         ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Alan @ 2007-02-10 19:06 UTC (permalink / raw)
  To: rol; +Cc: 'Robert Hancock', 'Linux Kernel Mailing List'

On Sat, 10 Feb 2007 19:39:21 +0100
"Paul Rolland" <rol@as2917.net> wrote:

> > I've been trying this, but I ended with the ICH7 not detecting anymore
> > my IDE disks... 
> > Should try again, maybe I missed something.
> 
> Done a new built, and I now have :
> 
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> hda: Maxtor 6L200P0, ATA DISK drive
> hdb: ASUS CRW-5232A3, ATAPI CD/DVD-ROM drive

You have the old driver 0n 0x1F0


> PCI: Device 0000:02:00.0 not available because of resource collisions
> ahci: probe of 0000:02:00.0 failed with error -22
> ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
> ata: 0x1F0 IDE port busy

And the new drivers trying to manage the same port

> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y

Set those to "N" and try again


^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-10 17:32   ` Paul Rolland
@ 2007-02-10 18:39     ` Paul Rolland
  2007-02-10 19:06       ` Alan
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-10 18:39 UTC (permalink / raw)
  To: rol, 'Robert Hancock'; +Cc: 'Linux Kernel Mailing List'

> I've been trying this, but I ended with the ICH7 not detecting anymore
> my IDE disks... 
> Should try again, maybe I missed something.

Done a new built, and I now have :

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: Maxtor 6L200P0, ATA DISK drive
hdb: ASUS CRW-5232A3, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
ata1: SATA max UDMA/133 cmd 0xFFFFC200000B6900 ctl 0x0 bmdma 0x0 irq 504
ata2: SATA max UDMA/133 cmd 0xFFFFC200000B6980 ctl 0x0 bmdma 0x0 irq 504
ata3: SATA max UDMA/133 cmd 0xFFFFC200000B6A00 ctl 0x0 bmdma 0x0 irq 504
ata4: SATA max UDMA/133 cmd 0xFFFFC200000B6A80 ctl 0x0 bmdma 0x0 irq 504
scsi0 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: qc timeout (cmd 0xec)
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: port failed to respond (30 secs, Status 0x80)
ata2: COMRESET failed (device not ready)
ata2: hardreset failed, retrying in 5 secs
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA 
ata2.00: ata2: dev 0 multi count 1
ata2.00: configured for UDMA/133
scsi2 : ahci
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for UDMA/133
scsi3 : ahci
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7, max UDMA/133, 976773168 sectors: LBA48 NCQ (depth 31/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      Maxtor 6L250S0   BANC PQ: 0 ANSI: 5
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access     ATA      Config  Disk     RGL1 PQ: 0 ANSI: 5
SCSI device sdb: 640 512-byte hdwr sectors (0 MB)
sdb: Write Protect is off
SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support
DPO or FUA
SCSI device sdb: 640 512-byte hdwr sectors (0 MB)
sdb: Write Protect is off
SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support
DPO or FUA
 sdb: unknown partition table
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:0:0: Direct-Access     ATA      Maxtor 6L250S0   BANC PQ: 0 ANSI: 5
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
sdc: Write Protect is off
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
sdc: Write Protect is off
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
 sdc: sdc1 sdc2
sd 2:0:0:0: Attached scsi disk sdc
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access     ATA      ST3500641AS      3.AA PQ: 0 ANSI: 5
SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
sdd: Write Protect is off
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
sdd: Write Protect is off
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
 sdd: sdd1 sdd2 sdd3
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg3 type 0
PCI: Device 0000:02:00.0 not available because of resource collisions
ahci: probe of 0000:02:00.0 failed with error -22
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
ata: 0x1F0 IDE port busy
ata: conflict with ide0
ata5: DUMMY
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
scsi4 : ata_piix
scsi5 : ata_piix
ATA: abnormal status 0x7F on port 0x177
PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 16 (level, low) -> IRQ 16
ata7: PATA max UDMA/100 cmd 0x9C00 ctl 0x9882 bmdma 0x9400 irq 16
ata8: PATA max UDMA/100 cmd 0x9800 ctl 0x9482 bmdma 0x9408 irq 16
scsi6 : pata_jmicron
ata7.00: ATAPI, max UDMA/66
ata7.00: qc timeout (cmd 0xef)
ata7.00: failed to set xfermode (err_mask=0x4)
ata7.00: limiting speed to UDMA/44
ata7: failed to recover some devices, retrying in 5 secs
ata7.00: qc timeout (cmd 0xef)
ata7.00: failed to set xfermode (err_mask=0x4)
ata7.00: limiting speed to PIO0
ata7: failed to recover some devices, retrying in 5 secs
ata7.00: qc timeout (cmd 0xef)
ata7.00: failed to set xfermode (err_mask=0x4)
ata7.00: disabled
scsi7 : pata_jmicron
ATA: abnormal status 0x7F on port 0x9807

So, the Jmicron stuff is still not working... It starts with the :
PCI: Device 0000:02:00.0 not available because of resource collisions
ahci: probe of 0000:02:00.0 failed with error -22

and then it fails to detect any kind of devices I have...

.config contains :
#
# ATA/ATAPI/MFM/RLL support
# 
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

# 
# Please see Documentation/ide.txt for help/info on IDE drives
# 
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y 
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_IDE_TASK_IOCTL=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
# CONFIG_BLK_DEV_IDEPCI is not set
# CONFIG_IDE_ARM is not set
# CONFIG_BLK_DEV_IDEDMA is not set
# CONFIG_IDEDMA_AUTO is not set
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set 
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
# 
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
...
(SCSI is set for USB devices I'm using).
...
#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
#
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SVW is not set
CONFIG_ATA_PIIX=y
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
CONFIG_SATA_INTEL_COMBINED=y
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD64X is not set 
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
CONFIG_PATA_JMICRON=y
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set

Robert, based on what you wrote, I have a few questions :
 - Should I activate CONFIG_SATA_SIL and/or CONFIG_SATA_SIL24 for the
   ata2 timeout,
 - If I set CONFIG_IDE=n, this will remove support for :
   . Floppy,
   . Scsi -> USB keys.
   or am I missing something ?

Regards,
Paul


^ permalink raw reply	[flat|nested] 18+ messages in thread

* RE: AHCI - remove probing of ata2
  2007-02-10 17:20 ` AHCI - remove probing of ata2 Robert Hancock
@ 2007-02-10 17:32   ` Paul Rolland
  2007-02-10 18:39     ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Paul Rolland @ 2007-02-10 17:32 UTC (permalink / raw)
  To: 'Robert Hancock'; +Cc: 'Linux Kernel Mailing List'

Hello,

> There is something connected, I believe what's actually there on this 
> board on that port is the SiI4723 chip which is connected to 
> two other 
> SATA ports. For whatever reason it gets detected as a drive, 
> and it also 
> seems to be not responding until we do a few resets..

That's correct, there is this controller, used by Asus for their EZ-Backup
feature. But I'm not using it, there is no disk connected on the associated
ports, and it's disabled in the BIOS.

> My advice on recent kernels is just set CONFIG_IDE=n and enable 
> PATA_JMICRON if you want JMicron support, unless you really 
> want to use the crusty old IDE layer..

No real preferences... except for a working machine, which is not what
I have for now...

I've been trying this, but I ended with the ICH7 not detecting anymore
my IDE disks... 
Should try again, maybe I missed something.

Regards,
Paul


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: AHCI - remove probing of ata2
       [not found] <fa.R5BFxVmVJj5OnAPGQI7410dt/fA@ifi.uio.no>
@ 2007-02-10 17:20 ` Robert Hancock
  2007-02-10 17:32   ` Paul Rolland
  0 siblings, 1 reply; 18+ messages in thread
From: Robert Hancock @ 2007-02-10 17:20 UTC (permalink / raw)
  To: rol; +Cc: 'Linux Kernel Mailing List'

Paul Rolland wrote:
> Hello,
> 
> I'm using an Asus P5W DH motherboard, with an Intel ICH7 controler, and a 
> Jmicron JMB363.
> 
> On the Intel, I've connected an IDE HDD and a CD-RW, no problem.
> On the SATA side, i've connected 3 SATA disks, but at boot time, the kernel
> detects 4 ports, and goes on timeout on ata2 :
> 
> ..
> ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
> ata1: SATA max UDMA/133 cmd 0xFFFFC200000BC900 ctl 0x0 bmdma 0x0 irq 505
> ata2: SATA max UDMA/133 cmd 0xFFFFC200000BC980 ctl 0x0 bmdma 0x0 irq 505
> ata3: SATA max UDMA/133 cmd 0xFFFFC200000BCA00 ctl 0x0 bmdma 0x0 irq 505
> ata4: SATA max UDMA/133 cmd 0xFFFFC200000BCA80 ctl 0x0 bmdma 0x0 irq 505
> scsi0 : ahci
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
> ata1.00: ata1: dev 0 multi count 0
> ata1.00: configured for UDMA/133
> scsi1 : ahci
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: qc timeout (cmd 0xec)
> ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
> ata2: port is slow to respond, please be patient (Status 0x80)
> ata2: port failed to respond (30 secs, Status 0x80)
> ata2: COMRESET failed (device not ready)
> ata2: hardreset failed, retrying in 5 secs
> ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA 
> ata2.00: ata2: dev 0 multi count 1
> ata2.00: configured for UDMA/133
> scsi2 : ahci
> ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 31/32)
> ata3.00: ata3: dev 0 multi count 0
> ata3.00: configured for UDMA/133
> ..
> 
> Is there a way to exclude ata2 from probing ? Nothing is connected, and there
> is no associated port on the motherboard...

There is something connected, I believe what's actually there on this 
board on that port is the SiI4723 chip which is connected to two other 
SATA ports. For whatever reason it gets detected as a drive, and it also 
seems to be not responding until we do a few resets..

http://www.siliconimage.com/products/product.aspx?id=64

> 
> 
> The second problem is the Jmicron controler. It can act as IDE, SATA, ...
> but I've configured it as IDE in the BIOS, and connected a DRD-RW on.
> Problem is that IDE driver detects it, as containing ide2 and ide3, and
> when probing for the DVD, I've got a lot of timeout on the command.
> .. But, I'm lost in all the JMICRON configuration possibilities in the 
> kernel :
>  - it is detected by the IDE driver,
>  - it can be activated in ATA/ATAPI/MFM/RLL
>  - it can be activated in Serial ATA (prod) and Parallel ATA (experimental)
> 
> What should I select ?

My advice on recent kernels is just set CONFIG_IDE=n and enable 
PATA_JMICRON if you want JMicron support, unless you really want to use 
the crusty old IDE layer..

-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/


^ permalink raw reply	[flat|nested] 18+ messages in thread

end of thread, other threads:[~2007-04-01 14:25 UTC | newest]

Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-02-10 14:24 AHCI - remove probing of ata2 Paul Rolland
2007-02-10 17:22 ` AHCI - remove probing of ata2 + Jmicron JMB363 ATA mode failing Paul Rolland
     [not found] <fa.R5BFxVmVJj5OnAPGQI7410dt/fA@ifi.uio.no>
2007-02-10 17:20 ` AHCI - remove probing of ata2 Robert Hancock
2007-02-10 17:32   ` Paul Rolland
2007-02-10 18:39     ` Paul Rolland
2007-02-10 19:06       ` Alan
2007-02-10 20:01         ` Paul Rolland
2007-02-10 20:36           ` Alan
2007-02-10 21:59             ` Paul Rolland
2007-02-11 10:17               ` Paul Rolland
2007-02-12  0:53                 ` Tejun Heo
2007-02-12 11:19                   ` Paul Rolland
2007-02-13  7:33                     ` Paul Rolland
2007-02-13 20:20                       ` Tejun Heo
2007-02-14  0:56 Greg Trounson
2007-02-14 17:47 ` Bill Davidsen
2007-02-14 21:43   ` Greg Trounson
2007-04-01 14:19 ` Håkan Lindqvist

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).