LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Shawn Lin <shawn.lin@rock-chips.com>
To: Doug Anderson <dianders@chromium.org>
Cc: shawn.lin@rock-chips.com, Jaehoon Chung <jh80.chung@samsung.com>,
	Ulf Hansson <ulf.hansson@linaro.org>,
	Alim Akhtar <alim.akhtar@samsung.com>,
	Sonny Rao <sonnyrao@chromium.org>,
	Heiko Stuebner <heiko@sntech.de>,
	Alexandru Stan <amstan@chromium.org>,
	"open list:ARM/Rockchip SoC..."
	<linux-rockchip@lists.infradead.org>,
	"linux-arm-kernel@lists.infradead.org" 
	<linux-arm-kernel@lists.infradead.org>,
	"linux-mmc@vger.kernel.org" <linux-mmc@vger.kernel.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH] mmc: dw_mmc: Consider HLE errors to be data and command errors
Date: Thu, 19 May 2016 19:31:53 +0800	[thread overview]
Message-ID: <10b3dc0e-aebf-664b-b36b-c54692cd9983@rock-chips.com> (raw)
In-Reply-To: <CAD=FV=UoT2GRYWJWXEn_ccvKGgC+PzQM_BCtLHAa7jxzbaQ9SA@mail.gmail.com>

Hi,

On 2016/5/19 1:37, Doug Anderson wrote:
> Hi,
>
> On Wed, May 18, 2016 at 2:14 AM, Shawn Lin <shawn.lin@rock-chips.com> wrote:
>> Hi
>>
>>
>> On 2016-5-18 12:12, Doug Anderson wrote:
>>>
>>> Hi,
>>>
>>> On Tue, May 17, 2016 at 6:59 PM, Shawn Lin
>>> <shawn.lin@kernel-upstream.org> wrote:
>>>>
>>>> Could you try this patch to see if you can still find HLE?
>>>>
>>>> @@ -2356,12 +2356,22 @@ static void dw_mci_cmd_interrupt(struct dw_mci
>>>> *host, u32 status)
>>>>   static void dw_mci_handle_cd(struct dw_mci *host)
>>>>   {
>>>>          int i;
>>>> +       int present;
>>>>
>>>>          for (i = 0; i < host->num_slots; i++) {
>>>>                  struct dw_mci_slot *slot = host->slot[i];
>>>>
>>>>                  if (!slot)
>>>>                          continue;
>>>>
>>>> +               present = !(mci_readl(slot->host, CDETECT) & (1 <<
>>>> slot->id));
>>>> +               if (present)
>>>> +                       set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
>>>> +               else
>>>> +                       clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
>>>
>>>
>>> No, because we don't use the builtin card detect on veyron.  ;)
>>>
>>> We use GPIO card detect because we didn't like the way JTAG and SD
>>> interacted.  Also on rk3288 the builtin card detect line had the wrong
>>> voltage domain (you couldn't detect a card when the IO lines were
>>> powered off).  The builtin card detect line is always driven low on
>>> veyron.
>>
>>
>> Okay, I see.
>>
>>>
>>>
>>> I'm nearly certain that the root cause of my HLE errors is actually
>>> related to the same problem addressed by the commit 7c5209c315ea
>>> ("mmc: core: Increase delay for voltage to stabilize from 3.3V to
>>> 1.8V").  I think that on minnie we're still on the hairy edge and
>>> sometimes the line doesn't transition fast enough.
>>
>>
>> Things are not so simple from your details.
>>
>> I was not enabling SD3.0 support, then I also found HLE sometimes.
>> So it seems commit 7c5209c315ea does not contibute to this phenomenon.
>
> Just to clarify, in my case commit 7c5209c315ea didn't make the
> problem worse, but made it better.  Just not better enough.  ;)
>
>
>> The scenario looks like:
>> remove sd-card -> mmc_sd_detect -> send status(CMD13) ->power_off ->
>> set_ios -> setup_bus -> disabled clk , then HLE irq storm coming
>>
>> From the code of dw_mci_prepare_command:
>> SDMMC_CMD_PRV_DAT_WAIT will not be used for CMD13, so we don't
>> wait_busy here, then cmd code is loding into queue of dw_mmc but
>> still failing send out because it's in busy?
>>
>> With my patch, things go well:
>> remove sd-card -> clear bit of DW_MMC_CARD_PRESENT  -> send
>> status(CMD13) return directly -> power_off -> set_ios -> setup_bus ->
>> disable clk
>>
>> So why should we allow inquiry of card status if we sure the card is
>> removed? I mean no any further cmds should be delivered.
>
> Quite honestly just dealing with the HLE error (my patch or
> equivalent) might be a sane solution for the problem you describe.

Yes, your patch looks good to me, so it should be merged firstly. :)
Then let's push it a bit further more that when HLEs are coming,
somethings must be wrong(currently I don't see a obvious clue from
the code itself although, I'm prone to think it belongs to the
software issue).


>
> dw_mmc needs to be able to work with an external card detect GPIO.
> It's been part of the dw_mmc driver for a long time and is (in fact)
> in use upstream at least by rk3288-veyron.  Any solution that only
> works for internal card detect is not enough.  Just handling the HLE
> error to deal with the interrupt storm and then letting Linux remove
> the card (because of the card detect interrupt) seems totally OK to
> me.
>

Sure, some of rockchip Socs use gpio for CD because they don't
have a internal CD, such as RK3036, right?

> Note: I'd be very curious if your problems get better if you disable

Not at all.

> the "grf_force_jtag" bit in the GRF.  If you're using the builtin card
> detect and you use the boot default of "grf_force_jtag" then your pins
> will be unmuxed behind your back when the card is ejected.  This could
> be causing the dw_mmc controller to get confused.

Right, grf_force_jtag is also not a friend of mine. :)
So I had disabled this function before I was debugging it.

>
>
>> And another question: should we wait busy for cmd13?
>
> I don't think so.  As I understand it CMD13 uses only the CMD line for
> communication and it should be appropriate to send this when the bus
> is "busy" (which means that the DATA lines are low).

Ahh... take back my question.. I was just considering a wired situation
that pins are unmuxed on the background(cmd line as well) when cmd13 is
delivering....


>
> Also: it seems odd that the HLE IRQ storm didn't come right after the
> CMD 13 in your description above.  Are you sure it was the CMD 13 that
> caused the HLEs, or could it has been something else?

Actually no. Any cmds be issued can trigger HLEs, I think, after sd card 
is removed When I hacked mmc_sd_detecd to send other cmds intead
of cmd13.

 From dw_mmc databook v270a(7.2.3 Clock Programming) we can see:
The DWC_mobile_storage loads each of these registers only when the
start_cmd bit and the Update_clk_regs_only bit in the CMD register are
set. When a command is successfully loaded, the DWC_mobile_storage
clears this bit, unless the DWC_mobile_storage already has another
command in the queue, at which point it gives an HLE (Hardware Locked
Error); for details on HLEs, refer to “Error Handling” on page 233.
Software should look for the start_cmd and the Update_clk_regs_only
bits, and should also set the wait_prvdata_complete bit to ensure that
clock parameters do not change during data transfer.

Maybe the cmd is trying to load(or somethings wrong with the
controller?) when we disable the clk? That may explain my observation
that HLEs came after disabling clk.


>
>
> -Doug
>
>
>


-- 
Best Regards
Shawn Lin

  parent reply	other threads:[~2016-05-19 11:32 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-03-10 15:48 Doug Anderson
2015-03-13 11:30 ` Jaehoon Chung
2015-03-13 20:27   ` Doug Anderson
2015-03-16  5:56     ` Jaehoon Chung
2015-03-30  0:55       ` Jaehoon Chung
2015-03-30 15:47         ` Doug Anderson
2016-05-18  0:47           ` Doug Anderson
2016-05-18  1:59             ` Shawn Lin
2016-05-18  4:12               ` Doug Anderson
2016-05-18  9:14                 ` Shawn Lin
2016-05-18 17:37                   ` Doug Anderson
2016-05-18 18:01                     ` Heiko Stuebner
2016-05-19 11:31                     ` Shawn Lin [this message]
2016-05-19 13:07                       ` Jaehoon Chung
2016-05-26  2:23                         ` Shawn Lin
2016-05-26  3:59                           ` Jaehoon Chung
2016-05-26  4:07                             ` Shawn Lin
2016-05-18  2:08             ` Jaehoon Chung
2016-05-18  4:13               ` Doug Anderson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=10b3dc0e-aebf-664b-b36b-c54692cd9983@rock-chips.com \
    --to=shawn.lin@rock-chips.com \
    --cc=alim.akhtar@samsung.com \
    --cc=amstan@chromium.org \
    --cc=dianders@chromium.org \
    --cc=heiko@sntech.de \
    --cc=jh80.chung@samsung.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=sonnyrao@chromium.org \
    --cc=ulf.hansson@linaro.org \
    --subject='Re: [PATCH] mmc: dw_mmc: Consider HLE errors to be data and command errors' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).