LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* D-Link DFE-580TX adapter problems
@ 2007-01-07 13:39 Anders Karlsson
  2007-01-08 20:12 ` Francois Romieu
  0 siblings, 1 reply; 5+ messages in thread
From: Anders Karlsson @ 2007-01-07 13:39 UTC (permalink / raw)
  To: LKML


[-- Attachment #1.1: Type: text/plain, Size: 824 bytes --]


Hi there,

I am having problems getting a network adapter going. I should see
eth1-eth4 from this adapter, but they do not show up with 'ifconfig -a'.
'alta-diag' and 'lspci' show the four NICs, which is what confuses me. I
even added some printk's in sundance.c to find out what happens, and as
far as I can see, the NICs get enabled - so why don't they show up for
ifconfig? I've tried both 2.6.19.1 (SMP) and 2.6.20-rc3 (both UP and
SMP) in addition to the 2.6.15-27 kernel of Ubuntu 6.06.

I have attached outputs from 'alta-diag', 'dmidecode' and 'lspci -vvv'
in the hope that someone might be able to give me a hint at what is
going wrong. I have searched the LKML archive and Googled and not found
anything related. :-/

Any hints or help appreciated.


-- 
Anders Karlsson <trudheim@gmail.com>

[-- Attachment #1.2: alta-diag-a.txt --]
[-- Type: text/plain, Size: 1170 bytes --]

alta-diag.c:v2.04 2/28/2005 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Sundance Technology Alta adapter at 0x8800.
 Station address 00:05:5d:e6:3e:1d.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
Index #2: Found a Sundance Technology Alta adapter at 0x8400.
 Station address 00:05:5d:e6:3e:1e.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
Index #3: Found a Sundance Technology Alta adapter at 0x8000.
 Station address 00:05:5d:e6:3e:1f.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
Index #4: Found a Sundance Technology Alta adapter at 0x7800.
 Station address 00:05:5d:e6:3e:20.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0100: Link status changed

[-- Attachment #1.3: alta-diag-e.txt --]
[-- Type: text/plain, Size: 1946 bytes --]

alta-diag.c:v2.04 2/28/2005 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Sundance Technology Alta adapter at 0x8800.
 Station address 00:05:5d:e6:3e:1d.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
 EEPROM address length 8, 256 words.
 EEPROM Subsystem IDs, Vendor 1186 Device 1012.
  EEPROM Station address is 00:05:5d:e6:3e:1d.
  Configuration 2afc, ASIC Control c063.
  Checksum 6dc1
Index #2: Found a Sundance Technology Alta adapter at 0x8400.
 Station address 00:05:5d:e6:3e:1e.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
 EEPROM address length 8, 256 words.
 EEPROM Subsystem IDs, Vendor 1186 Device 1012.
  EEPROM Station address is 00:05:5d:e6:3e:1e.
  Configuration 2afc, ASIC Control c063.
  Checksum 954d
Index #3: Found a Sundance Technology Alta adapter at 0x8000.
 Station address 00:05:5d:e6:3e:1f.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
 EEPROM address length 8, 256 words.
 EEPROM Subsystem IDs, Vendor 1186 Device 1012.
  EEPROM Station address is 00:05:5d:e6:3e:1f.
  Configuration 2afc, ASIC Control c063.
  Checksum c2c9
Index #4: Found a Sundance Technology Alta adapter at 0x7800.
 Station address 00:05:5d:e6:3e:20.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0100: Link status changed
 EEPROM address length 8, 256 words.
 EEPROM Subsystem IDs, Vendor 1186 Device 1012.
  EEPROM Station address is 00:05:5d:e6:3e:20.
  Configuration 2afc, ASIC Control c063.
  Checksum f37d

[-- Attachment #1.4: alta-diag-m.txt --]
[-- Type: text/plain, Size: 6795 bytes --]

alta-diag.c:v2.04 2/28/2005 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Sundance Technology Alta adapter at 0x8800.
 Station address 00:05:5d:e6:3e:1d.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
 MII PHY found at address 0, status 0x7809.
 MII PHY found at address 1, status 0x7809.
 MII PHY #0 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 MII PHY #1 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
libmii.c:v2.11 2/28/2005  Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
 MII PHY #0 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 Basic mode control register 0x1100: Auto-negotiation enabled.
 Basic mode status register 0x7809 ... 7809.
   Link status: not established.
   Capable of  100baseTx-FD 100baseTx 10baseT-FD 10baseT.
   Able to perform Auto-negotiation, negotiation not complete.
 Vendor ID is 00:08:85:--:--:--, model 35 rev. 0.
   Vendor/Part: Alta/Kendin Sundance.
 I'm advertising 01e1: 100baseTx-FD 100baseTx 10baseT-FD 10baseT
   Advertising no additional info pages.
   IEEE 802.3 CSMA/CD protocol.
 Link partner capability is 0000:.
   Negotiation did not complete.
Index #2: Found a Sundance Technology Alta adapter at 0x8400.
 Station address 00:05:5d:e6:3e:1e.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
 MII PHY found at address 0, status 0x7809.
 MII PHY found at address 1, status 0x7809.
 MII PHY #0 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 MII PHY #1 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
libmii.c:v2.11 2/28/2005  Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
 MII PHY #0 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 Basic mode control register 0x1100: Auto-negotiation enabled.
 Basic mode status register 0x7809 ... 7809.
   Link status: not established.
   Capable of  100baseTx-FD 100baseTx 10baseT-FD 10baseT.
   Able to perform Auto-negotiation, negotiation not complete.
 Vendor ID is 00:08:85:--:--:--, model 35 rev. 0.
   Vendor/Part: Alta/Kendin Sundance.
 I'm advertising 01e1: 100baseTx-FD 100baseTx 10baseT-FD 10baseT
   Advertising no additional info pages.
   IEEE 802.3 CSMA/CD protocol.
 Link partner capability is 0000:.
   Negotiation did not complete.
Index #3: Found a Sundance Technology Alta adapter at 0x8000.
 Station address 00:05:5d:e6:3e:1f.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0000: No interrupts pending.
 MII PHY found at address 0, status 0x7809.
 MII PHY found at address 1, status 0x7809.
 MII PHY #0 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 MII PHY #1 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
libmii.c:v2.11 2/28/2005  Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
 MII PHY #0 transceiver registers:
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   1100 7809 0022 1630 01e1 0000 0004 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 Basic mode control register 0x1100: Auto-negotiation enabled.
 Basic mode status register 0x7809 ... 7809.
   Link status: not established.
   Capable of  100baseTx-FD 100baseTx 10baseT-FD 10baseT.
   Able to perform Auto-negotiation, negotiation not complete.
 Vendor ID is 00:08:85:--:--:--, model 35 rev. 0.
   Vendor/Part: Alta/Kendin Sundance.
 I'm advertising 01e1: 100baseTx-FD 100baseTx 10baseT-FD 10baseT
   Advertising no additional info pages.
   IEEE 802.3 CSMA/CD protocol.
 Link partner capability is 0000:.
   Negotiation did not complete.
Index #4: Found a Sundance Technology Alta adapter at 0x7800.
 Station address 00:05:5d:e6:3e:20.
  Receive mode is 0x00: Uninitialized/disabled.
  MAC mode is 0000: half duplex.
  Tx status 00, threshold 8188.
  Interrupt status is 0100: Link status changed
 MII PHY found at address 0, status 0x782d.
 MII PHY found at address 1, status 0x782d.
 MII PHY #0 transceiver registers:
   1100 782d 0022 1630 01e1 45e1 0007 2001
   1100 782d 0022 1630 01e1 45e1 0007 2001
   1100 782d 0022 1630 01e1 45e1 0007 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 MII PHY #1 transceiver registers:
   1100 782d 0022 1630 01e1 45e1 0007 2001
   1100 782d 0022 1630 01e1 45e1 0007 2001
   1100 782d 0022 1630 01e1 45e1 0007 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
libmii.c:v2.11 2/28/2005  Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
 MII PHY #0 transceiver registers:
   1100 782d 0022 1630 01e1 45e1 0007 2001
   1100 782d 0022 1630 01e1 45e1 0007 2001
   1100 782d 0022 1630 01e1 45e1 0007 2001
   0000 0000 0000 0000 0000 0000 0000 0000.
 Basic mode control register 0x1100: Auto-negotiation enabled.
 Basic mode status register 0x782d ... 782d.
   Link status: established.
   Capable of  100baseTx-FD 100baseTx 10baseT-FD 10baseT.
   Able to perform Auto-negotiation, negotiation complete.
 Vendor ID is 00:08:85:--:--:--, model 35 rev. 0.
   Vendor/Part: Alta/Kendin Sundance.
 I'm advertising 01e1: 100baseTx-FD 100baseTx 10baseT-FD 10baseT
   Advertising no additional info pages.
   IEEE 802.3 CSMA/CD protocol.
 Link partner capability is 45e1: Flow-control 100baseTx-FD 100baseTx 10baseT-FD 10baseT.
   Negotiation  completed.

[-- Attachment #1.5: dmidecode.txt --]
[-- Type: text/plain, Size: 14849 bytes --]

# dmidecode 2.7
SMBIOS 2.3 present.
54 structures occupying 1448 bytes.
Table at 0x000F38A0.

Handle 0x0000, DMI type 0, 20 bytes.
BIOS Information
	Vendor: Award Software, Inc.
	Version: ASUS A7V600 ACPI BIOS Revision 1008
	Release Date: 09/02/2004
	Address: 0xF0000
	Runtime Size: 64 kB
	ROM Size: 256 kB
	Characteristics:
		PCI is supported
		PNP is supported
		APM is supported
		BIOS is upgradeable
		BIOS shadowing is allowed
		ESCD support is available
		Boot from CD is supported
		Selectable boot is supported
		BIOS ROM is socketed
		EDD is supported
		5.25"/360 KB floppy services are supported (int 13h)
		5.25"/1.2 MB floppy services are supported (int 13h)
		3.5"/720 KB floppy services are supported (int 13h)
		3.5"/2.88 MB floppy services are supported (int 13h)
		Print screen service is supported (int 5h)
		8042 keyboard services are supported (int 9h)
		Serial services are supported (int 14h)
		Printer services are supported (int 17h)
		CGA/mono video services are supported (int 10h)
		ACPI is supported
		USB legacy is supported
		AGP is supported

Handle 0x0001, DMI type 1, 25 bytes.
System Information
	Manufacturer: System Manufacturer
	Product Name: System Name
	Version: System Version
	Serial Number: SYS-1234567890
	UUID: Not Settable
	Wake-up Type: Power Switch

Handle 0x0002, DMI type 2, 8 bytes.
Base Board Information
	Manufacturer: ASUSTeK Computer INC.
	Product Name: A7V600
	Version: REV 1.xx
	Serial Number: xxxxxxxxxxx

Handle 0x0003, DMI type 3, 17 bytes.
Chassis Information
	Manufacturer: Chassis Manufacture
	Type: Tower
	Lock: Not Present
	Version: Chassis Version
	Serial Number: Chassis Serial Number
	Asset Tag: Asset-1234567890
	Boot-up State: Safe
	Power Supply State: Safe
	Thermal State: Safe
	Security Status: Unknown
	OEM Information: 0x00000002

Handle 0x0004, DMI type 4, 32 bytes.
Processor Information
	Socket Designation: SOCKET A
	Type: Central Processor
	Family: Other
	Manufacturer: AuthenticAMD
	ID: A0 06 00 00 FF FB 83 03
	Version: AMD Sempron(TM) 3000+
	Voltage: 1.5 V
	External Clock: 166 MHz
	Max Speed: 2250 MHz
	Current Speed: 2000 MHz
	Status: Populated, Enabled
	Upgrade: Other
	L1 Cache Handle: 0x0009
	L2 Cache Handle: 0x000A
	L3 Cache Handle: Not Provided

Handle 0x0005, DMI type 5, 22 bytes.
Memory Controller Information
	Error Detecting Method: None
	Error Correcting Capabilities:
		Other
	Supported Interleave: Unknown
	Current Interleave: Unknown
	Maximum Memory Module Size: 1024 MB
	Maximum Total Memory Size: 3072 MB
	Supported Speeds:
		70 ns
		60 ns
		50 ns
	Supported Memory Types:
		ECC
		DIMM
		SDRAM
	Memory Module Voltage: 3.3 V
	Associated Memory Slots: 3
		0x0006
		0x0007
		0x0008
	Enabled Error Correcting Capabilities:
		Unknown

Handle 0x0006, DMI type 6, 12 bytes.
Memory Module Information
	Socket Designation: DIMM 1
	Bank Connections: 0 1
	Current Speed: Unknown
	Type: DIMM SDRAM
	Installed Size: 512 MB (Single-bank Connection)
	Enabled Size: 512 MB (Single-bank Connection)
	Error Status: OK

Handle 0x0007, DMI type 6, 12 bytes.
Memory Module Information
	Socket Designation: DIMM 2
	Bank Connections: 2 3
	Current Speed: Unknown
	Type: DIMM SDRAM
	Installed Size: 512 MB (Double-bank Connection)
	Enabled Size: 512 MB (Double-bank Connection)
	Error Status: OK

Handle 0x0008, DMI type 6, 12 bytes.
Memory Module Information
	Socket Designation: DIMM 3
	Bank Connections: 4 5
	Current Speed: Unknown
	Type: DIMM SDRAM
	Installed Size: 1024 MB (Double-bank Connection)
	Enabled Size: 1024 MB (Double-bank Connection)
	Error Status: OK

Handle 0x0009, DMI type 7, 19 bytes.
Cache Information
	Socket Designation: L1 Cache
	Configuration: Enabled, Not Socketed, Level 1
	Operational Mode: Write Back
	Location: Internal
	Installed Size: 128 KB
	Maximum Size: 128 KB
	Supported SRAM Types:
		Pipeline Burst
		Synchronous
	Installed SRAM Type: Pipeline Burst Synchronous
	Speed: Unknown
	Error Correction Type: Unknown
	System Type: Data
	Associativity: 4-way Set-associative

Handle 0x000A, DMI type 7, 19 bytes.
Cache Information
	Socket Designation: L2 Cache
	Configuration: Enabled, Not Socketed, Level 2
	Operational Mode: Write Back
	Location: Internal
	Installed Size: 512 KB
	Maximum Size: 8192 KB
	Supported SRAM Types:
		Pipeline Burst
		Synchronous
	Installed SRAM Type: Pipeline Burst Synchronous
	Speed: Unknown
	Error Correction Type: Unknown
	System Type: Data
	Associativity: 4-way Set-associative

Handle 0x000B, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: PRIMARY IDE/HDD
	Internal Connector Type: On Board IDE
	External Reference Designator: Not Specified
	External Connector Type: None
	Port Type: None

Handle 0x000C, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: SECONDARY IDE/HDD
	Internal Connector Type: On Board IDE
	External Reference Designator: Not Specified
	External Connector Type: None
	Port Type: None

Handle 0x000D, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: FLOPPY
	Internal Connector Type: On Board Floppy
	External Reference Designator: Not Specified
	External Connector Type: None
	Port Type: None

Handle 0x000E, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB1
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x000F, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB2
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0010, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB3
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0011, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB4
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0012, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB5
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0013, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB6
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0014, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB7
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0015, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: USB8
	External Connector Type: Access Bus (USB)
	Port Type: USB

Handle 0x0016, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: PS/2 Keyboard
	External Connector Type: PS/2
	Port Type: Keyboard Port

Handle 0x0017, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: PS/2 Mouse
	External Connector Type: PS/2
	Port Type: Mouse Port

Handle 0x0018, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Parallel Port
	External Connector Type: DB-25 female
	Port Type: Parallel Port ECP/EPP

Handle 0x0019, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Serial Port 1
	External Connector Type: DB-9 male
	Port Type: Serial Port 16550 Compatible

Handle 0x001A, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Serial Port 2
	External Connector Type: DB-9 male
	Port Type: Serial Port 16550 Compatible

Handle 0x001B, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Joystick Port
	External Connector Type: DB-15 female
	Port Type: Joystick Port

Handle 0x001C, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: MIDI Port
	External Connector Type: DB-15 female
	Port Type: MIDI Port

Handle 0x001D, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Line In Jack
	External Connector Type: Mini Jack (headphones)
	Port Type: Audio Port

Handle 0x001E, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Lan
	External Connector Type: RJ-45
	Port Type: Network Port

Handle 0x001F, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Serial ATA1
	External Connector Type: Other
	Port Type: None

Handle 0x0020, DMI type 8, 9 bytes.
Port Connector Information
	Internal Reference Designator: Not Specified
	Internal Connector Type: None
	External Reference Designator: Serial ATA2
	External Connector Type: Other
	Port Type: None

Handle 0x0021, DMI type 9, 13 bytes.
System Slot Information
	Designation: PCI 1
	Type: 32-bit PCI
	Current Usage: Available
	Length: Short
	ID: 1
	Characteristics:
		5.0 V is provided
		3.3 V is provided
		PME signal is supported

Handle 0x0022, DMI type 9, 13 bytes.
System Slot Information
	Designation: PCI 2
	Type: 32-bit PCI
	Current Usage: In Use
	Length: Short
	ID: 2
	Characteristics:
		5.0 V is provided
		3.3 V is provided
		PME signal is supported

Handle 0x0023, DMI type 9, 13 bytes.
System Slot Information
	Designation: PCI 3
	Type: 32-bit PCI
	Current Usage: In Use
	Length: Short
	ID: 3
	Characteristics:
		5.0 V is provided
		3.3 V is provided
		PME signal is supported

Handle 0x0024, DMI type 9, 13 bytes.
System Slot Information
	Designation: PCI 4
	Type: 32-bit PCI
	Current Usage: Available
	Length: Short
	ID: 4
	Characteristics:
		5.0 V is provided
		3.3 V is provided
		PME signal is supported

Handle 0x0025, DMI type 9, 13 bytes.
System Slot Information
	Designation: PCI 5
	Type: 32-bit PCI
	Current Usage: Available
	Length: Short
	ID: 5
	Characteristics:
		5.0 V is provided
		3.3 V is provided
		PME signal is supported

Handle 0x0026, DMI type 9, 13 bytes.
System Slot Information
	Designation: PCI 6
	Type: 32-bit PCI
	Current Usage: In Use
	Length: Short
	ID: 6
	Characteristics:
		5.0 V is provided
		3.3 V is provided
		PME signal is supported

Handle 0x0027, DMI type 9, 13 bytes.
System Slot Information
	Designation: AGP
	Type: 32-bit AGP 8x
	Current Usage: In Use
	Length: Short
	Characteristics:
		3.3 V is provided

Handle 0x0028, DMI type 11, 5 bytes.
OEM Strings
	String 1: 0
	String 2: 0

Handle 0x0029, DMI type 13, 22 bytes.
BIOS Language Information
	Installable Languages: 1
		en|US|iso8859-1
	Currently Installed Language: en|US|iso8859-1

Handle 0x002A, DMI type 14, 14 bytes.
Group Associations
	Name: Cpu Module
	Items: 3
		0x0004 (Processor)
		0x0009 (Cache)
		0x000A (Cache)

Handle 0x002B, DMI type 14, 29 bytes.
Group Associations
	Name: Memory Module Set
	Items: 8
		0x0029 (Physical Memory Array)
		0x002A (Memory Device)
		0x002E (Memory Device Mapped Address)
		0x002B (Memory Device)
		0x002F (Memory Device Mapped Address)
		0x002C (Memory Device)
		0x0030 (Memory Device Mapped Address)
		0x002D (Memory Array Mapped Address)

Handle 0x002C, DMI type 16, 15 bytes.
Physical Memory Array
	Location: System Board Or Motherboard
	Use: System Memory
	Error Correction Type: None
	Maximum Capacity: 3 GB
	Error Information Handle: Not Provided
	Number Of Devices: 3

Handle 0x002D, DMI type 17, 23 bytes.
Memory Device
	Array Handle: 0x002C
	Error Information Handle: No Error
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 512 MB
	Form Factor: DIMM
	Set: 1
	Locator: DDR 1
	Bank Locator: Not Specified
	Type: DRAM
	Type Detail: Synchronous
	Speed: Unknown

Handle 0x002E, DMI type 17, 23 bytes.
Memory Device
	Array Handle: 0x002C
	Error Information Handle: No Error
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 512 MB
	Form Factor: DIMM
	Set: 2
	Locator: DDR 2
	Bank Locator: Not Specified
	Type: DRAM
	Type Detail: Synchronous
	Speed: Unknown

Handle 0x002F, DMI type 17, 23 bytes.
Memory Device
	Array Handle: 0x002C
	Error Information Handle: No Error
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 1024 MB
	Form Factor: DIMM
	Set: 3
	Locator: DDR 3
	Bank Locator: Not Specified
	Type: DRAM
	Type Detail: Synchronous
	Speed: Unknown

Handle 0x0030, DMI type 19, 15 bytes.
Memory Array Mapped Address
	Starting Address: 0x00000000000
	Ending Address: 0x0003FFFFFFF
	Range Size: 1 GB
	Physical Array Handle: 0x0029
	Partition Width: 0

Handle 0x0031, DMI type 20, 19 bytes.
Memory Device Mapped Address
	Starting Address: 0x00000000000
	Ending Address: 0x0001FFFFFFF
	Range Size: 512 MB
	Physical Device Handle: 0x002D
	Memory Array Mapped Address Handle: 0x002D
	Partition Row Position: 1

Handle 0x0032, DMI type 20, 19 bytes.
Memory Device Mapped Address
	Starting Address: 0x00020000000
	Ending Address: 0x0003FFFFFFF
	Range Size: 512 MB
	Physical Device Handle: 0x002E
	Memory Array Mapped Address Handle: 0x002D
	Partition Row Position: 2

Handle 0x0033, DMI type 20, 19 bytes.
Memory Device Mapped Address
	Starting Address: 0x00040000000
	Ending Address: 0x0007FFFFFFF
	Range Size: 1 GB
	Physical Device Handle: 0x002F
	Memory Array Mapped Address Handle: 0x002D
	Partition Row Position: 3

Handle 0x0034, DMI type 32, 11 bytes.
System Boot Information
	Status: No errors detected

Handle 0x0035, DMI type 127, 4 bytes.
End Of Table


[-- Attachment #1.6: lspci-vvv.txt --]
[-- Type: text/plain, Size: 17311 bytes --]

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
	Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at fc000000 (32-bit, prefetchable) [size=32M]
	Capabilities: [80] AGP version 3.5
		Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8,x@
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: de800000-dfdfffff
	Prefetchable memory behind bridge: e0000000-fbffffff
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:09.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] (rev 12)
	Subsystem: ASUSTeK Computer Inc. P4P800/K8V Deluxe motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16K]
	Region 1: I/O ports at b800 [size=256]
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data

0000:00:0a.0 RAID bus controller: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host Controller (rev 02)
	Subsystem: Silicon Image, Inc. Winic W-680 (Silicon Image 680 based)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x01 (4 bytes)
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at b400 [size=8]
	Region 1: I/O ports at b000 [size=4]
	Region 2: I/O ports at a800 [size=8]
	Region 3: I/O ports at a400 [size=4]
	Region 4: I/O ports at a000 [size=16]
	Region 5: Memory at dd800000 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at 88100000 [disabled] [size=512K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:00:0d.0 SCSI storage controller: LSI Logic / Symbios Logic 53C896/897 (rev 07)
	Subsystem: LSI Logic / Symbios Logic LSI21002 PCI to Dual Channel Ultra2 SCSI host adapter
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at 9800 [size=256]
	Region 1: Memory at dd000000 (64-bit, non-prefetchable) [size=1K]
	Region 3: Memory at dc800000 (64-bit, non-prefetchable) [size=8K]
	Expansion ROM at 88180000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0d.1 SCSI storage controller: LSI Logic / Symbios Logic 53C896/897 (rev 07)
	Subsystem: LSI Logic / Symbios Logic LSI21002 PCI to Dual Channel Ultra2 SCSI host adapter
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin B routed to IRQ 18
	Region 0: I/O ports at 9400 [size=256]
	Region 1: Memory at dc000000 (64-bit, non-prefetchable) [size=1K]
	Region 3: Memory at db800000 (64-bit, non-prefetchable) [size=8K]
	Expansion ROM at 88190000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0e.0 PCI bridge: Intel Corporation 21152 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x08 (32 bytes)
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
	I/O behind bridge: 00007000-00008fff
	Memory behind bridge: 88000000-880fffff
	Prefetchable memory behind bridge: 00000000dfe00000-00000000dfe00000
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+

0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V Deluxe/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at 6800 [size=8]
	Region 1: I/O ports at 6400 [size=4]
	Region 2: I/O ports at 6000 [size=8]
	Region 3: I/O ports at 5800 [size=4]
	Region 4: I/O ports at 5400 [size=16]
	Region 5: I/O ports at 5000 [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin A routed to IRQ 17
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
	Region 4: I/O ports at 4800 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 19
	Region 4: I/O ports at 4400 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 19
	Region 4: I/O ports at 4000 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at 3800 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at 3400 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin C routed to IRQ 19
	Region 0: Memory at db000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
	Subsystem: ASUSTeK Computer Inc. A7V600/K8V Deluxe motherboard (ADI AD1980 codec [SoundMAX])
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin C routed to IRQ 22
	Region 0: I/O ports at e000 [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin C routed to IRQ 22
	Region 0: I/O ports at e500 [size=256]
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (rev 01) (prog-if 00 [VGA])
	Subsystem: PC Partner Limited: Unknown device 7c26
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at d800 [size=256]
	Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at effe0000 [disabled] [size=128K]
	Capabilities: [58] AGP version 3.0
		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (Secondary) (rev 01)
	Subsystem: PC Partner Limited: Unknown device 7c27
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
	Region 1: Memory at de800000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:04.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12)
	Subsystem: D-Link System Inc DFE-580TX
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at 8800 [size=128]
	Expansion ROM at dfe00000 [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:02:05.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12)
	Subsystem: D-Link System Inc DFE-580TX
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 20
	Region 0: I/O ports at 8400 [size=128]
	Expansion ROM at dfe10000 [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:02:06.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12)
	Subsystem: D-Link System Inc DFE-580TX
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at 8000 [size=128]
	Expansion ROM at dfe20000 [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:02:07.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12)
	Subsystem: D-Link System Inc DFE-580TX
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at 7800 [size=128]
	Expansion ROM at dfe30000 [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-


[-- Attachment #1.7: ver_linux.txt --]
[-- Type: text/plain, Size: 2173 bytes --]

If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
 
Linux lenin 2.6.20-rc3 #0 SMP Wed Jan 3 13:51:02 GMT 2007 i686 GNU/Linux
 
Gnu C                  4.0.3
Gnu make               3.81beta4
binutils               2.16.91
util-linux             2.12r
mount                  2.12r
module-init-tools      3.2.2
e2fsprogs              1.38
jfsutils               1.1.8
reiserfsprogs          3.6.19
reiser4progs           1.0.5
xfsprogs               2.7.7
pcmciautils            012
pcmcia-cs              3.2.8
quota-tools            3.13.
PPP                    2.4.4b1
nfs-utils              1.0.7
Linux C Library        2.3.6
Dynamic linker (ldd)   2.3.6
Procps                 3.2.6
Net-tools              1.60
Console-tools          0.2.3
Sh-utils               5.93
udev                   079
wireless-tools         28
Modules Loaded         nls_cp437 isofs udf radeon drm radeonfb i2c_algo_bit fb_ddc fbcon tileblit font bitblit softcursor binfmt_misc rfcomm l2cap pktcdvd nfsd exportfs lockd sunrpc autofs4 capability commoncap cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_ondemand freq_table cpufreq_conservative video sbs i2c_ec dock button battery container ac asus_acpi backlight ipv6 quota_v2 snd_seq_dummy snd_seq_oss snd_seq_midi snd_seq_midi_event snd_seq ipt_MASQUERADE ipt_REJECT ipt_LOG xt_tcpudp xt_state xt_multiport iptable_filter iptable_nat nf_nat ip_tables x_tables nf_conntrack_ipv4 nf_conntrack nfnetlink hci_usb bluetooth usblp snd_via82xx_modem snd_pcm_oss snd_mixer_oss snd_via82xx gameport snd_ac97_codec ac97_bus snd_mpu401_uart snd_rawmidi snd_seq_device snd_pcm snd_timer serio_raw sundance mii snd floppy soundcore snd_page_alloc sk98lin pata_sil680 ata_generic pata_via shpchp pci_hotplug skge via_agp agpgart sg evdev it87 hwmon_vid eeprom i2c_isa i2c_viapro i2c_core softdog psmouse parport_pc lp parport ext3 jbd mbcache dm_mirror ide_generic ehci_hcd uhci_hcd usbcore generic sd_mod sata_via sym53c8xx scsi_transport_spi ide_cd cdrom ide_disk thermal processor fan raid1 md_mod dm_mod via82cxxx siimage

[-- Attachment #2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 3838 bytes --]

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: D-Link DFE-580TX adapter problems
  2007-01-07 13:39 D-Link DFE-580TX adapter problems Anders Karlsson
@ 2007-01-08 20:12 ` Francois Romieu
  2007-01-08 23:01   ` Anders Karlsson
  0 siblings, 1 reply; 5+ messages in thread
From: Francois Romieu @ 2007-01-08 20:12 UTC (permalink / raw)
  To: Anders Karlsson; +Cc: LKML

Anders Karlsson <trudheim@gmail.com> :
[...]

No message from the sundance driver in dmesg ?

-- 
Ueimor

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: D-Link DFE-580TX adapter problems
  2007-01-08 20:12 ` Francois Romieu
@ 2007-01-08 23:01   ` Anders Karlsson
  2007-01-09 23:09     ` Francois Romieu
  0 siblings, 1 reply; 5+ messages in thread
From: Anders Karlsson @ 2007-01-08 23:01 UTC (permalink / raw)
  To: Francois Romieu; +Cc: LKML

[-- Attachment #1: Type: text/plain, Size: 849 bytes --]

On Mon, 2007-01-08 at 21:12 +0100, Francois Romieu wrote:
> Anders Karlsson <trudheim@gmail.com> :
> [...]
> 
> No message from the sundance driver in dmesg ?

 # rmmod sundance mii
 # modprobe sundance
 # dmesg | tail
[138689.114754] sundance.c:v1.2 11-Sep-2006  Written by Donald Becker
[138689.114757]   http://www.scyld.com/network/sundance.html
 #

That is all that turns up (I stripped out the iptables messages that was
not relevant to the driver) at the end of the dmesg output. I have
checked the driver against the lspci output, the driver has the correct
PCI ID's in there, so this driver *should* work. In the past, it *has*
worked, but that was on a older kernel (2.6.8 or thereabouts).

If there are patches or tweaks to the driver, I am willing and able to
test them.

-- 
Anders Karlsson <trudheim@gmail.com>

[-- Attachment #2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 3838 bytes --]

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: D-Link DFE-580TX adapter problems
  2007-01-08 23:01   ` Anders Karlsson
@ 2007-01-09 23:09     ` Francois Romieu
  2007-01-10 22:45       ` Anders Karlsson
  0 siblings, 1 reply; 5+ messages in thread
From: Francois Romieu @ 2007-01-09 23:09 UTC (permalink / raw)
  To: Anders Karlsson; +Cc: LKML

[-- Attachment #1: Type: text/plain, Size: 452 bytes --]

Anders Karlsson <trudheim@gmail.com> :
[...]
> PCI ID's in there, so this driver *should* work. In the past, it *has*
> worked, but that was on a older kernel (2.6.8 or thereabouts).

No datapoint beyond 2.6.12 ? It would make thinks easier (for you :o} ).

> If there are patches or tweaks to the driver, I am willing and able to
> test them.

Compressed patch attached. Apply with patch -R and see if it behaves
differently. No warranty.

-- 
Ueimor

[-- Attachment #2: sundance.patch.gz --]
[-- Type: application/x-gzip, Size: 1593 bytes --]

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: D-Link DFE-580TX adapter problems
  2007-01-09 23:09     ` Francois Romieu
@ 2007-01-10 22:45       ` Anders Karlsson
  0 siblings, 0 replies; 5+ messages in thread
From: Anders Karlsson @ 2007-01-10 22:45 UTC (permalink / raw)
  To: Francois Romieu; +Cc: LKML

[-- Attachment #1: Type: text/plain, Size: 1117 bytes --]

On Wed, 2007-01-10 at 00:09 +0100, Francois Romieu wrote:
> Anders Karlsson <trudheim@gmail.com> :
> [...]
> > PCI ID's in there, so this driver *should* work. In the past, it *has*
> > worked, but that was on a older kernel (2.6.8 or thereabouts).
> 
> No datapoint beyond 2.6.12 ? It would make thinks easier (for you :o} ).

Unfortunately the adapter has been sitting idle in an antistat bag for
some time, and last time I used it was with a Debian Sarge install. I
can try some older Ubuntu LiveCD's (will take some time to download
though) and try and get a point in time where it works.

> > If there are patches or tweaks to the driver, I am willing and able to
> > test them.
> 
> Compressed patch attached. Apply with patch -R and see if it behaves
> differently. No warranty.

Many thanks for the patch. Applied to 2.6.20-rc4, built as K7-SMP, but
unfortunately it behaves no different compared to stock 2.6.20-rc4. If
you have any other ideas, I am game for some testing. Meanwhile, I'll
grab some LiveCD's to get data-points.

Cheers!

-- 
Anders Karlsson <trudheim@gmail.com>

[-- Attachment #2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 3838 bytes --]

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2007-01-10 22:46 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-01-07 13:39 D-Link DFE-580TX adapter problems Anders Karlsson
2007-01-08 20:12 ` Francois Romieu
2007-01-08 23:01   ` Anders Karlsson
2007-01-09 23:09     ` Francois Romieu
2007-01-10 22:45       ` Anders Karlsson

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).