LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Pascal Terjan <pterjan@mandriva.com>
To: linux-kernel <linux-kernel@vger.kernel.org>
Subject: pm_op(): pci_pm_restore+0x0/0x70 returns -16
Date: Tue, 28 Oct 2008 11:41:59 +0100	[thread overview]
Message-ID: <1225190519.8039.14.camel@plop> (raw)

Since I updated my laptop (Thikpad T40) to 2.6.27-rc5 and all new
kernels until 2.6.27.3 (was using 2.6.25 before), I get this at resume
time after hibernation :

Oct 28 10:39:18 plop kernel: pm_op(): pci_pm_restore+0x0/0x70 returns
-16
Oct 28 10:39:19 plop kernel: PM: Device 0000:00:00.0 failed to restore:
error -16

This may or may not be related to resume issues I often get.

Sometimes it still work fine, sometimes it panics but I can't get any
log, sometimes I get back to X but without USB mouse, without keyboard
and ssh not responding (sysrq still work).

 00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O
Controller (rev 03)
	Subsystem: IBM Thinkpad T40 series
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [e4] Vendor Specific Information <?>
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp


Here is the warn level log of the resume :

Oct 28 10:39:16 plop kernel: Syncing filesystems ... done.
Oct 28 10:39:18 plop kernel: Freezing user space processes ... (elapsed
0.06 seconds) done.
Oct 28 10:39:18 plop kernel: Freezing remaining freezable tasks ...
(elapsed 0.00 seconds) done.
Oct 28 10:39:18 plop kernel: Suspending console(s) (use
no_console_suspend to debug)
Oct 28 10:39:18 plop kernel: Disabling non-boot CPUs ...
Oct 28 10:39:21 plop kernel: Restarting tasks ... done.
Oct 28 10:45:26 plop kernel: Emergency Sync complete

Here is the info level :

Oct 28 10:39:18 plop kernel: PM: Shrinking memory... done (92359 pages
freed)
Oct 28 10:39:18 plop kernel: PM: Freed 369436 kbytes in 12.51 seconds
(29.53 MB/s)
Oct 28 10:39:18 plop kernel: sd 0:0:0:0: [sda] Synchronizing SCSI cache
Oct 28 10:39:18 plop kernel: nsc-ircc 00:0b: disabled
Oct 28 10:39:18 plop kernel: parport_pc 00:0a: disabled
Oct 28 10:39:18 plop kernel: serial 00:09: disabled
Oct 28 10:39:18 plop kernel: eth4: Going into suspend...
Oct 28 10:39:18 plop kernel: ipw2200 0000:02:02.0: PCI INT A disabled
Oct 28 10:39:18 plop kernel: ACPI handle has no context!
Oct 28 10:39:18 plop kernel: Intel ICH Modem 0000:00:1f.6: PCI INT B
disabled
Oct 28 10:39:18 plop kernel: Intel ICH 0000:00:1f.5: PCI INT B disabled
Oct 28 10:39:18 plop kernel: ata_piix 0000:00:1f.1: PCI INT A disabled
Oct 28 10:39:18 plop kernel: ehci_hcd 0000:00:1d.7: PCI INT D disabled
Oct 28 10:39:18 plop kernel: uhci_hcd 0000:00:1d.2: PCI INT C disabled
Oct 28 10:39:18 plop kernel: uhci_hcd 0000:00:1d.1: PCI INT B disabled
Oct 28 10:39:18 plop kernel: uhci_hcd 0000:00:1d.0: PCI INT A disabled
Oct 28 10:39:18 plop kernel: ACPI: Preparing to enter system sleep state
S4
Oct 28 10:39:18 plop kernel: Extended CMOS year: 2000
Oct 28 10:39:18 plop kernel: PM: Creating hibernation image: 
Oct 28 10:39:18 plop kernel: PM: Need to copy 91604 pages
Oct 28 10:39:18 plop kernel: Intel machine check architecture supported.
Oct 28 10:39:18 plop kernel: Intel machine check reporting enabled on
CPU#0.
Oct 28 10:39:18 plop kernel: Extended CMOS year: 2000
Oct 28 10:39:18 plop kernel: ACPI: Waking up from system sleep state S4
Oct 28 10:39:18 plop kernel: ACPI: EC: non-query interrupt received,
switching to interrupt mode
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.0: power state changed
by ACPI to D0
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.0: PCI INT A ->
Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.0: setting latency
timer to 64
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.1: power state changed
by ACPI to D0
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.1: PCI INT B ->
Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.1: setting latency
timer to 64
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.2: PCI INT C ->
Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: uhci_hcd 0000:00:1d.2: setting latency
timer to 64
Oct 28 10:39:21 plop kernel: ehci_hcd 0000:00:1d.7: power state changed
by ACPI to D0
Oct 28 10:39:21 plop kernel: ehci_hcd 0000:00:1d.7: PCI INT D ->
Link[LNKH] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: ehci_hcd 0000:00:1d.7: setting latency
timer to 64
Oct 28 10:39:21 plop kernel: pci 0000:00:1e.0: restoring config space at
offset 0x6 (was 0x40080200, writing 0x40100200)
Oct 28 10:39:21 plop kernel: pci 0000:00:1e.0: setting latency timer to
64
Oct 28 10:39:21 plop kernel: ata_piix 0000:00:1f.1: restoring config
space at offset 0x1 (was 0x2800003, writing 0x2800007)
Oct 28 10:39:21 plop kernel: ata_piix 0000:00:1f.1: PCI INT A ->
Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: ata_piix 0000:00:1f.1: setting latency
timer to 64
Oct 28 10:39:21 plop kernel: Intel ICH 0000:00:1f.5: restoring config
space at offset 0x1 (was 0x2900007, writing 0x2900003)
Oct 28 10:39:21 plop kernel: Intel ICH 0000:00:1f.5: PCI INT B ->
Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: Intel ICH 0000:00:1f.5: setting latency
timer to 64
Oct 28 10:39:21 plop kernel: ata2.00: ACPI cmd ef/03:42:00:00:00:a0
filtered out
Oct 28 10:39:21 plop kernel: ata2.00: ACPI cmd ef/03:0c:00:00:00:a0
filtered out
Oct 28 10:39:21 plop kernel: ata1.00: ACPI cmd ef/02:00:00:00:00:a0
succeeded
Oct 28 10:39:21 plop kernel: ata1.00: ACPI cmd f5/00:00:00:00:00:a0
filtered out
Oct 28 10:39:21 plop kernel: ata1.00: ACPI cmd ef/03:45:00:00:00:a0
filtered out
Oct 28 10:39:21 plop kernel: ata1.00: ACPI cmd ef/03:0c:00:00:00:a0
filtered out
Oct 28 10:39:21 plop kernel: ata2.00: ACPI cmd e3/00:1f:00:00:00:a0
succeeded
Oct 28 10:39:21 plop kernel: ata2.00: ACPI cmd e3/00:02:00:00:00:a0
succeeded
Oct 28 10:39:21 plop kernel: ata1.00: configured for UDMA/100
Oct 28 10:39:21 plop kernel: ata2.00: configured for UDMA/33
Oct 28 10:39:21 plop kernel: ata1.00: configured for UDMA/100
Oct 28 10:39:21 plop kernel: ata1: EH complete
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] 156301488 512-byte
hardware sectors (80026 MB)
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] 156301488 512-byte
hardware sectors (80026 MB)
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Oct 28 10:39:21 plop kernel: Intel ICH Modem 0000:00:1f.6: PCI INT B ->
Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: Intel ICH Modem 0000:00:1f.6: setting
latency timer to 64
Oct 28 10:39:21 plop kernel: pci 0000:01:00.0: power state changed by
ACPI to D0
Oct 28 10:39:21 plop kernel: pci 0000:01:00.0: PCI INT A -> Link[LNKA]
-> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: yenta_cardbus 0000:02:00.0: restoring
config space at offset 0xf (was 0x3c0010b, writing 0x5c0010b)
Oct 28 10:39:21 plop kernel: yenta_cardbus 0000:02:00.0: restoring
config space at offset 0x3 (was 0x824008, writing 0x82a820)
Oct 28 10:39:21 plop kernel: yenta_cardbus 0000:02:00.0: restoring
config space at offset 0x1 (was 0x2100107, writing 0x2100007)
Oct 28 10:39:21 plop kernel: yenta_cardbus 0000:02:00.1: restoring
config space at offset 0xf (was 0x3c0020b, writing 0x5c0020b)
Oct 28 10:39:21 plop kernel: yenta_cardbus 0000:02:00.1: restoring
config space at offset 0x3 (was 0x824008, writing 0x82a820)
Oct 28 10:39:21 plop kernel: yenta_cardbus 0000:02:00.1: restoring
config space at offset 0x1 (was 0x2100107, writing 0x2100007)
Oct 28 10:39:21 plop kernel: eth4: Coming out of suspend...
Oct 28 10:39:21 plop kernel: ipw2200 0000:02:02.0: PCI INT A ->
Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
Oct 28 10:39:21 plop kernel: serial 00:09: activated
Oct 28 10:39:21 plop kernel: parport_pc 00:0a: activated
Oct 28 10:39:21 plop kernel: nsc-ircc 00:0b: activated
Oct 28 10:39:21 plop kernel: sd 0:0:0:0: [sda] Starting disk
Oct 28 10:39:21 plop kernel: usb 3-2: reset low speed USB device using
uhci_hcd and address 3
Oct 28 10:39:21 plop kernel: usb 3-2: device firmware changed
Oct 28 10:39:21 plop kernel: usb 3-2: USB disconnect, address 3
Oct 28 10:39:22 plop kernel: agpgart-intel 0000:00:00.0: AGP 2.0 bridge
Oct 28 10:39:22 plop kernel: agpgart-intel 0000:00:00.0: putting AGP V2
device into 4x mode
Oct 28 10:39:22 plop kernel: pci 0000:01:00.0: putting AGP V2 device
into 4x mode
Oct 28 10:39:22 plop kernel: [drm] Loading R100 Microcode
Oct 28 10:45:26 plop kernel: SysRq : Emergency Sync
Oct 28 10:45:29 plop kernel: SysRq : Keyboard mode set to system default



             reply	other threads:[~2008-10-28 10:42 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-10-28 10:41 Pascal Terjan [this message]
2008-10-28 23:18 ` Rafael J. Wysocki
2008-10-29  2:38   ` Pascal Terjan
2008-10-29 21:30     ` Rafael J. Wysocki

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1225190519.8039.14.camel@plop \
    --to=pterjan@mandriva.com \
    --cc=linux-kernel@vger.kernel.org \
    --subject='Re: pm_op(): pci_pm_restore+0x0/0x70 returns -16' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).