Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Zhu Yi]

On Mon, 2008-10-27 at 18:02 -0700, Mirco Tischler wrote:
> Hi
> 
> I have problems connecting to wlan with my iwl4965 chip and 2.6.28-rc2 (didn't
> test -rc1). Networkmanager just times out every time.
> Only after playing around with rmmod/modprobe and killswitch I am sometimes
> able to connect. But I cannot reproduce this reliably yet.
> 
> This is what I get in dmesg (from modprobe iwlagn to connection failure):
> 
> [ 1881.884690] iwlagn: Intel(R) Wireless WiFi Link AGN driver for
> Linux,1.3.27kds
> [ 1881.884692] iwlagn: Copyright(c) 2003-2008 Intel Corporation
> [ 1881.884809] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 1881.884836] iwlagn 0000:06:00.0: setting latency timer to 64
> [ 1881.884952] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
> [ 1881.935149] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
> [ 1881.936327] phy4: Selected rate control algorithm 'iwl-agn-rs'
> [ 1885.965591] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 1885.965874] iwlagn 0000:06:00.0: irq 41 for MSI/MSI-X
> [ 1885.965974] iwlagn 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
> [ 1886.181600] Registered led device: iwl-phy4:radio
> [ 1886.181618] Registered led device: iwl-phy4:assoc
> [ 1886.181635] Registered led device: iwl-phy4:RX
> [ 1886.181654] Registered led device: iwl-phy4:TX
> [ 1886.213631] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 1887.572768] iwlagn: TX Power requested while scanning!

Looks good so far. But I failed to see what are you trying to connect?
Can you try "iwconfig wlan0 channnel <> essid <>"?

> What might be related is this early on boot:
> 
> [    0.163009] cfg80211: Calling CRDA to update world regulatory domain
> [    0.163012] cfg80211: Failed calling CRDA
> [    0.163024] cfg80211: calling CRDA failed - unable to update world
> regulatory domain, using static definition

Does your AP work on A band?

Thanks,
-yi

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 533 bytes --]

On Tue, 28 Oct 2008 09:33:37 +0800, Zhu Yi wrote:
> 
> Looks good so far. But I failed to see what are you trying to connect?
> Can you try "iwconfig wlan0 channnel <> essid <>"?
Sorry. I should have supplied that information on the first try. The network is
a standard WPA-protected G-band network at 2.437Ghz (channel 6).
That command seems to help a bit. At least I was able to connect more often
after executing it. I will observe that in detail tomorrow though.
> 
> Does your AP work on A band?
> 
> Thanks,
> -yi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Zhu Yi]

On Mon, 2008-10-27 at 18:59 -0700, Mirco Tischler wrote:
> > Looks good so far. But I failed to see what are you trying to
> connect?
> > Can you try "iwconfig wlan0 channnel <> essid <>"?
> Sorry. I should have supplied that information on the first try. The
> network is
> a standard WPA-protected G-band network at 2.437Ghz (channel 6).
> That command seems to help a bit. At least I was able to connect more
> often after executing it.

You don't need this command if wpa_supplicant works correctly. Is it a
hidden SSID AP?

Thanks,
-yi

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 218 bytes --]

On Tue, 28 Oct 2008 10:19:50 +0800, Zhu Yi wrote:
> You don't need this command if wpa_supplicant works correctly. Is it a
> hidden SSID AP?
No it isn't. Did I mention it worked well with 2.6.27?
> Thanks,
> -yi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Arjan van de Ven]

On Tue, 28 Oct 2008 09:33:37 +0800
Zhu Yi <yi.zhu@intel.com> wrote:

> On Mon, 2008-10-27 at 18:02 -0700, Mirco Tischler wrote:
> > Hi
> > 
> > I have problems connecting to wlan with my iwl4965 chip and
> > 2.6.28-rc2 (didn't test -rc1). Networkmanager just times out every
> > time. Only after playing around with rmmod/modprobe and killswitch
> > I am sometimes able to connect. But I cannot reproduce this
> > reliably yet.
> > 
> > This is what I get in dmesg (from modprobe iwlagn to connection
> > failure):
> > 
> > [ 1881.884690] iwlagn: Intel(R) Wireless WiFi Link AGN driver for
> > Linux,1.3.27kds
> > [ 1881.884692] iwlagn: Copyright(c) 2003-2008 Intel Corporation
> > [ 1881.884809] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level,
> > low) -> IRQ 18 [ 1881.884836] iwlagn 0000:06:00.0: setting latency
> > timer to 64 [ 1881.884952] iwlagn: Detected Intel Wireless WiFi
> > Link 4965AGN REV=0x4 [ 1881.935149] iwlagn: Tunable channels: 13
> > 802.11bg, 19 802.11a channels [ 1881.936327] phy4: Selected rate
> > control algorithm 'iwl-agn-rs' [ 1885.965591] iwlagn 0000:06:00.0:
> > PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1885.965874] iwlagn
> > 0000:06:00.0: irq 41 for MSI/MSI-X [ 1885.965974] iwlagn
> > 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
> > [ 1886.181600] Registered led device: iwl-phy4:radio [ 1886.181618]
> > Registered led device: iwl-phy4:assoc [ 1886.181635] Registered led
> > device: iwl-phy4:RX [ 1886.181654] Registered led device:
> > iwl-phy4:TX [ 1886.213631] ADDRCONF(NETDEV_UP): wlan0: link is not
> > ready [ 1887.572768] iwlagn: TX Power requested while scanning!
> 
> Looks good so far. But I failed to see what are you trying to connect?
> Can you try "iwconfig wlan0 channnel <> essid <>"?
> 

I had this same issue

turning on CONFIG_WIRELESS_OLD_REGULATORY fixed it for me....

-- 
Arjan van de Ven 	Intel Open Source Technology Centre
For development, discussion and tips for power savings, 
visit http://www.lesswatts.org

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Zhu Yi]

On Mon, 2008-10-27 at 22:32 -0600, Arjan van de Ven wrote:
> I had this same issue
> 
> turning on CONFIG_WIRELESS_OLD_REGULATORY fixed it for me....

Arjan,

This is a different bug. He has the wireless worked sometimes.

I think your problem relates to 5GHz channel usage. We have already a
patch queued to resolve the problem. We will have regulatory framework
reworked to better solve the problem. But I guess it will be in .29 time
frame.

Thanks,
-yi

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 2375 bytes --]

On Tue, 28 Oct 2008 13:23:34 +0800, Zhu Yi wrote:
> On Mon, 2008-10-27 at 22:32 -0600, Arjan van de Ven wrote:
> > I had this same issue
> > 
> > turning on CONFIG_WIRELESS_OLD_REGULATORY fixed it for me....
> 
> Arjan,
> 
> This is a different bug. He has the wireless worked sometimes.
> 
> I think your problem relates to 5GHz channel usage. We have already a
> patch queued to resolve the problem. We will have regulatory framework
> reworked to better solve the problem. But I guess it will be in .29 time
> frame.
> 
> Thanks,
> -yi
I tested Arjan's solution nevertheless and it seems to do the job. I can't find
the "TX Power requested" line anymore on dmesg output with that config option
enabled anymore and it connects without problems.
This is how it looks now:
[  777.680750] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux,1.3.27kds 
[  777.680753] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[  777.680878] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[  777.680908] iwlagn 0000:06:00.0: setting latency timer to 64
[  777.680977] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[  777.731255] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
[  777.732432] phy1: Selected rate control algorithm 'iwl-agn-rs'
[  781.764539] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[  781.764821] iwlagn 0000:06:00.0: irq 41 for MSI/MSI-X
[  781.764919] iwlagn 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
[  781.980719] Registered led device: iwl-phy1:radio
[  781.980764] Registered led device: iwl-phy1:assoc
[  781.980808] Registered led device: iwl-phy1:RX
[  781.980856] Registered led device: iwl-phy1:TX
[  782.014001] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  783.633713] wlan0: authenticate with AP 00:c0:a8:e5:e5:a5
[  783.635637] wlan0: authenticated
[  783.635644] wlan0: associate with AP 00:c0:a8:e5:e5:a5
[  783.642770] wlan0: RX AssocResp from 00:c0:a8:e5:e5:a5 (capab=0x431 status=0
aid=1) 
[  783.642776] wlan0: associated [  783.669684] ADDRCONF(NETDEV_CHANGE): wlan0:
link becomes ready

I tested it quickly and not very thoroughly on the wpa-eap encrypted network at
university and it showed the same behaviour: no connection without
CONFIG_WIRELESS_OLD_REGULATORY and no problems with it enabled.

Thanks
Mirco

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Johannes Berg]

[-- Attachment #1: Type: text/plain, Size: 711 bytes --]

On Tue, 2008-10-28 at 17:24 +0100, Mirco Tischler wrote:

> > This is a different bug. He has the wireless worked sometimes.
> > 
> > I think your problem relates to 5GHz channel usage. We have already a
> > patch queued to resolve the problem. We will have regulatory framework
> > reworked to better solve the problem. But I guess it will be in .29 time
> > frame.
> > 
> > Thanks,
> > -yi
> I tested Arjan's solution nevertheless and it seems to do the job. I can't find
> the "TX Power requested" line anymore on dmesg output with that config option
> enabled anymore and it connects without problems.

Can we have a dmesg output with the "TX power requested" line posted
here?

johannes

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1.1: Type: text/plain, Size: 420 bytes --]

On Tue, 28 Oct 2008 19:36:34 +0100, Johannes Berg wrote:
> Can we have a dmesg output with the "TX power requested" line posted
> here?
> 
> johannes
You mean the hole output? Cause I posted the wireless part in my initial mail.

Anyway, I'll have to recreate it cause I unfortunately didn't store it and I
can't find any saved dmesg in /var/log that still contains that line. So be
patient please ;)

Mirco

[-- Attachment #1.2: dmesg --]
[-- Type: text/plain, Size: 68734 bytes --]

[    0.000000] BIOS EBDA/lowmem at: 0009f800/0009f800
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 2.6.28-rc2 (mirco@mtlp.12.dimension) (gcc version 4.3.0 20080428 (Red Hat 4.3.0-8) (GCC) ) #25 SMP PREEMPT Tue Oct 28 13:05:04 CET 2008
[    0.000000] Command line: ro root=/dev/master/root rhgb quiet
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007f670000 (usable)
[    0.000000]  BIOS-e820: 000000007f670000 - 000000007f67e000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007f67e000 - 0000000080000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] last_pfn = 0x7f670 max_arch_pfn = 0x3ffffffff
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] original variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 2GB, type WB
[    0.000000] reg 1, base: 2039MB, range: 1MB, type UC
[    0.000000] reg 2, base: 2040MB, range: 8MB, type UC
[    0.000000] total RAM coverred: 2039M
[    0.000000]  gran_size: 64K 	chunk_size: 64K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 64K 	chunk_size: 128K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 64K 	chunk_size: 256K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 64K 	chunk_size: 512K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 64K 	chunk_size: 1M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 64K 	chunk_size: 2M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 64K 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 64K 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 64K 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 64K 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 128K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 128K 	chunk_size: 256K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 128K 	chunk_size: 512K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 128K 	chunk_size: 1M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 128K 	chunk_size: 2M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 128K 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 128K 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 128K 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 128K 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 256K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 256K 	chunk_size: 512K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 256K 	chunk_size: 1M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 256K 	chunk_size: 2M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 256K 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 256K 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 256K 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 256K 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 512K 	num_reg: 8  	lose cover RAM: 3M
[    0.000000]  gran_size: 512K 	chunk_size: 1M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 512K 	chunk_size: 2M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 512K 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 512K 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 512K 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 512K 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 1M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 1M 	chunk_size: 2M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 1M 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 1M 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 1M 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 1M 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 0G
[    0.000000]  gran_size: 2M 	chunk_size: 2M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 2M 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000] *BAD*gran_size: 2M 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 2M 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 2M 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 1M
[    0.000000]  gran_size: 4M 	chunk_size: 4M 	num_reg: 8  	lose cover RAM: 3M
[    0.000000] *BAD*gran_size: 4M 	chunk_size: 8M 	num_reg: 8  	lose cover RAM: -1M
[    0.000000]  gran_size: 4M 	chunk_size: 16M 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 32M 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 64M 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 128M 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 512M 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 4M 	chunk_size: 2G 	num_reg: 3  	lose cover RAM: 3M
[    0.000000]  gran_size: 8M 	chunk_size: 8M 	num_reg: 7  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 16M 	num_reg: 7  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 32M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 64M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 128M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 256M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 8M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 16M 	num_reg: 7  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 32M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 64M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 128M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 256M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 16M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 7M
[    0.000000]  gran_size: 32M 	chunk_size: 32M 	num_reg: 6  	lose cover RAM: 23M
[    0.000000]  gran_size: 32M 	chunk_size: 64M 	num_reg: 2  	lose cover RAM: 23M
[    0.000000]  gran_size: 32M 	chunk_size: 128M 	num_reg: 2  	lose cover RAM: 23M
[    0.000000]  gran_size: 32M 	chunk_size: 256M 	num_reg: 2  	lose cover RAM: 23M
[    0.000000]  gran_size: 32M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 23M
[    0.000000]  gran_size: 32M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 23M
[    0.000000]  gran_size: 32M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 23M
[    0.000000]  gran_size: 64M 	chunk_size: 64M 	num_reg: 5  	lose cover RAM: 55M
[    0.000000]  gran_size: 64M 	chunk_size: 128M 	num_reg: 2  	lose cover RAM: 55M
[    0.000000]  gran_size: 64M 	chunk_size: 256M 	num_reg: 2  	lose cover RAM: 55M
[    0.000000]  gran_size: 64M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 55M
[    0.000000]  gran_size: 64M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 55M
[    0.000000]  gran_size: 64M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 55M
[    0.000000]  gran_size: 128M 	chunk_size: 128M 	num_reg: 4  	lose cover RAM: 119M
[    0.000000]  gran_size: 128M 	chunk_size: 256M 	num_reg: 2  	lose cover RAM: 119M
[    0.000000]  gran_size: 128M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 119M
[    0.000000]  gran_size: 128M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 119M
[    0.000000]  gran_size: 128M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 119M
[    0.000000]  gran_size: 256M 	chunk_size: 256M 	num_reg: 3  	lose cover RAM: 247M
[    0.000000]  gran_size: 256M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 247M
[    0.000000]  gran_size: 256M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 247M
[    0.000000]  gran_size: 256M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 247M
[    0.000000]  gran_size: 512M 	chunk_size: 512M 	num_reg: 2  	lose cover RAM: 503M
[    0.000000]  gran_size: 512M 	chunk_size: 1G 	num_reg: 2  	lose cover RAM: 503M
[    0.000000]  gran_size: 512M 	chunk_size: 2G 	num_reg: 2  	lose cover RAM: 503M
[    0.000000]  gran_size: 1G 	chunk_size: 1G 	num_reg: 1  	lose cover RAM: 1015M
[    0.000000]  gran_size: 1G 	chunk_size: 2G 	num_reg: 1  	lose cover RAM: 1015M
[    0.000000]  gran_size: 2G 	chunk_size: 2G 	num_reg: 0  	lose cover RAM: 2039M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000] gran_size: 64K 	chunk_size: 16M 	num_reg: 3  	lose RAM: 0G
[    0.000000] range0: 0000000000000000 - 0000000080000000
[    0.000000] Setting variable MTRR 0, base: 0GB, range: 2GB, type WB
[    0.000000] hole: 000000007f700000 - 0000000080000000
[    0.000000] Setting variable MTRR 1, base: 2039MB, range: 1MB, type UC
[    0.000000] Setting variable MTRR 2, base: 2040MB, range: 8MB, type UC
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Scanning 2 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000001000 (usable)
[    0.000000]  modified: 0000000000001000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 0000000000008000 (usable)
[    0.000000]  modified: 0000000000008000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 0000000000092800 (usable)
[    0.000000]  modified: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000d2000 - 00000000000d4000 (reserved)
[    0.000000]  modified: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000007f670000 (usable)
[    0.000000]  modified: 000000007f670000 - 000000007f67e000 (ACPI NVS)
[    0.000000]  modified: 000000007f67e000 - 0000000080000000 (reserved)
[    0.000000]  modified: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  modified: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  modified: 00000000fed14000 - 00000000fed1a000 (reserved)
[    0.000000]  modified: 00000000fed1c000 - 00000000fed90000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ff000000 - 0000000100000000 (reserved)
[    0.000000] init_memory_mapping
[    0.000000]  0000000000 - 007f600000 page 2M
[    0.000000]  007f600000 - 007f670000 page 4k
[    0.000000] kernel direct mapping tables up to 7f670000 @ 10000-14000
[    0.000000] last_map_addr: 7f670000 end: 7f670000
[    0.000000] RAMDISK: 37c7d000 - 37fef8c9
[    0.000000] ACPI: RSDP 000F7F50, 0024 (r2 PTLTD )
[    0.000000] ACPI: XSDT 7F67670D, 008C (r1 PTLTD  	 XSDT    6040000  LTP        0)
[    0.000000] ACPI: FACP 7F67CCDD, 00F4 (r3 INTEL  CRESTLNE  6040000 ALAN        1)
[    0.000000] ACPI: DSDT 7F677AD2, 5197 (r2 INTEL  CRESTLNE  6040000 INTL 20050624)
[    0.000000] ACPI: FACS 7F67DFC0, 0040
[    0.000000] ACPI: APIC 7F67CDD1, 0068 (r1 INTEL  CRESTLNE  6040000 LOHR       5A)
[    0.000000] ACPI: HPET 7F67CE39, 0038 (r1 INTEL  CRESTLNE  6040000 LOHR       5A)
[    0.000000] ACPI: MCFG 7F67CE71, 003C (r1 INTEL  CRESTLNE  6040000 LOHR       5A)
[    0.000000] ACPI: TCPA 7F67CEAD, 0032 (r1 Intel   CRESTLN  6040000          5A52)
[    0.000000] ACPI: TMOR 7F67CEDF, 0026 (r1 PTLTD            6040000 PTL         3)
[    0.000000] ACPI: ASF! 7F67CF05, 006B (r32 OEMID  OEMTBL    6040000 PTL         1)
[    0.000000] ACPI: APIC 7F67CF70, 0068 (r1 PTLTD  	 APIC    6040000  LTP        0)
[    0.000000] ACPI: BOOT 7F67CFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
[    0.000000] ACPI: SSDT 7F6777F5, 02DD (r1 SataRe SataAhci     1000 INTL 20050624)
[    0.000000] ACPI: SSDT 7F676D25, 025F (r1  PmRef  Cpu0Tst     3000 INTL 20050624)
[    0.000000] ACPI: SSDT 7F676C7F, 00A6 (r1  PmRef  Cpu1Tst     3000 INTL 20050624)
[    0.000000] ACPI: SSDT 7F676799, 04E6 (r1  PmRef    CpuPm     3000 INTL 20050624)
[    0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[    0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-000000007f670000
[    0.000000] Bootmem setup node 0 0000000000000000-000000007f670000
[    0.000000]   NODE_DATA [0000000000012000 - 0000000000015fff]
[    0.000000]   bootmap [0000000000016000 -  0000000000025ecf] pages 10
[    0.000000] (6 early reservations) ==> bootmem [0000000000 - 007f670000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
[    0.000000]   #2 [0001000000 - 0001742a0c]    TEXT DATA BSS ==> [0001000000 - 0001742a0c]
[    0.000000]   #3 [0037c7d000 - 0037fef8c9]          RAMDISK ==> [0037c7d000 - 0037fef8c9]
[    0.000000]   #4 [000009f800 - 0000100000]    BIOS reserved ==> [000009f800 - 0000100000]
[    0.000000]   #5 [0000010000 - 0000012000]          PGTABLE ==> [0000010000 - 0000012000]
[    0.000000] found SMP MP-table at [ffff8800000f7f80] 000f7f80
[    0.000000]  [ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001a00000-ffff8800035fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00100000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000001
[    0.000000]     0: 0x00000006 -> 0x00000008
[    0.000000]     0: 0x00000010 -> 0x00000092
[    0.000000]     0: 0x00000100 -> 0x0007f670
[    0.000000] On node 0 totalpages: 521717
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 103 pages reserved
[    0.000000]   DMA zone: 3814 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 7079 pages used for memmap
[    0.000000]   DMA32 zone: 510665 pages, LIFO batch:31
[    0.000000]   Normal zone: 0 pages used for memmap
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 0000000000008000 - 0000000000010000
[    0.000000] PM: Registered nosave memory: 0000000000092000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[    0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[    0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[    0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[    0.000000] PERCPU: Allocating 53248 bytes of per cpu data
[    0.000000] per cpu data for cpu0 on node0 at 0000000001753000
[    0.000000] per cpu data for cpu1 on node0 at 0000000001760000
[    0.000000] NR_CPUS: 4, nr_cpu_ids: 2, nr_node_ids 1
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 514479
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: ro root=/dev/master/root rhgb quiet
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[    0.000000] Extended CMOS year: 2000
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2194.533 MHz processor.
[    0.000999] Console: colour VGA+ 80x25
[    0.000999] console [tty0] enabled
[    0.000999] Scanning for low memory corruption every 60 seconds
[    0.000999] Checking aperture...
[    0.000999] No AGP bridge found
[    0.000999] Calgary: detecting Calgary via BIOS EBDA area
[    0.000999] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000999] Memory: 2046892k/2087360k available (3870k kernel code, 39976k reserved, 2301k data, 480k init)
[    0.000999] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000999] hpet clockevent registered
[    0.000999] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 4389.06 BogoMIPS (lpj=2194533)
[    0.000999] Security Framework initialized
[    0.000999] SELinux:  Initializing.
[    0.000999] SELinux:  Starting in permissive mode
[    0.000999] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.001574] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.002170] Mount-cache hash table entries: 256
[    0.002330] Initializing cgroup subsys ns
[    0.002334] Initializing cgroup subsys cpuacct
[    0.002340] Initializing cgroup subsys freezer
[    0.002359] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.002360] CPU: L2 cache: 4096K
[    0.002362] CPU 0/0x0 -> Node 0
[    0.002364] CPU: Physical Processor ID: 0
[    0.002365] CPU: Processor Core ID: 0
[    0.002367] using mwait in idle threads.
[    0.002385] ACPI: Core revision 20080926
[    0.011060] Setting APIC routing to flat
[    0.011377] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.021620] CPU0: Intel(R) Core(TM)2 Duo CPU     T7500  @ 2.20GHz stepping 0a
[    0.021996] Booting processor 1 APIC 0x1 ip 0x6000
[    0.000999] Initializing CPU#1
[    0.000999] Calibrating delay using timer specific routine.. 4388.79 BogoMIPS (lpj=2194397)
[    0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.000999] CPU: L2 cache: 4096K
[    0.000999] CPU 1/0x1 -> Node 0
[    0.000999] CPU: Physical Processor ID: 0
[    0.000999] CPU: Processor Core ID: 1
[    0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[    0.093269] CPU1: Intel(R) Core(TM)2 Duo CPU     T7500  @ 2.20GHz stepping 0a
[    0.093290] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.094003] Brought up 2 CPUs
[    0.094006] Total of 2 processors activated (8777.86 BogoMIPS).
[    0.094210] net_namespace: 1344 bytes
[    0.094404] NET: Registered protocol family 16
[    0.095010] ACPI: bus type pci registered
[    0.095026] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.095026] PCI: MCFG area at e0000000 reserved in E820
[    0.109210] PCI: Using MMCONFIG at e0000000 - efffffff
[    0.109212] PCI: Using configuration type 1 for base access
[    0.113988] ACPI: EC: Look up EC in DSDT
[    0.116902] ACPI: BIOS _OSI(Linux) query ignored
[    0.116904] ACPI: DMI System Vendor: Zepto
[    0.116906] ACPI: DMI Product Name: Znote
[    0.116907] ACPI: DMI Product Version: 6024W
[    0.116908] ACPI: DMI Board Name: Znote
[    0.116909] ACPI: DMI BIOS Vendor: Phoenix Technologies LTD
[    0.116911] ACPI: DMI BIOS Date: 12/20/2007
[    0.116912] ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
[    0.116914] ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
[    0.117987] ACPI: Interpreter enabled
[    0.117987] ACPI: (supports S0 S3 S4 S5)
[    0.117987] ACPI: Using IOAPIC for interrupt routing
[    0.118999] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.122002] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.139070] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.139071] ACPI: EC: driver started in poll mode
[    0.139244] ACPI: No dock devices found.
[    0.139254] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.139359] pci 0000:00:02.0: reg 10 64bit mmio: [0xf0800000-0xf08fffff]
[    0.139366] pci 0000:00:02.0: reg 18 64bit mmio: [0xd0000000-0xdfffffff]
[    0.139370] pci 0000:00:02.0: reg 20 io port: [0x1800-0x1807]
[    0.139403] pci 0000:00:02.1: reg 10 64bit mmio: [0xf0900000-0xf09fffff]
[    0.139498] pci 0000:00:1a.0: reg 20 io port: [0x1820-0x183f]
[    0.139555] pci 0000:00:1a.1: reg 20 io port: [0x1840-0x185f]
[    0.139620] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf1104800-0xf1104bff]
[    0.139996] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.140001] pci 0000:00:1a.7: PME# disabled
[    0.140050] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf0f00000-0xf0f03fff]
[    0.140086] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.140090] pci 0000:00:1b.0: PME# disabled
[    0.140147] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.140152] pci 0000:00:1c.0: PME# disabled
[    0.140211] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.140215] pci 0000:00:1c.1: PME# disabled
[    0.140274] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.140278] pci 0000:00:1c.2: PME# disabled
[    0.140337] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.140341] pci 0000:00:1c.3: PME# disabled
[    0.140400] pci 0000:00:1d.0: reg 20 io port: [0x1860-0x187f]
[    0.140457] pci 0000:00:1d.1: reg 20 io port: [0x1880-0x189f]
[    0.140514] pci 0000:00:1d.2: reg 20 io port: [0x18a0-0x18bf]
[    0.140578] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf1104c00-0xf1104fff]
[    0.140624] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.140629] pci 0000:00:1d.7: PME# disabled
[    0.140766] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[    0.140770] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[    0.140803] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[    0.140810] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[    0.140818] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[    0.140825] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[    0.140832] pci 0000:00:1f.1: reg 20 io port: [0x1810-0x181f]
[    0.140896] pci 0000:00:1f.2: reg 10 io port: [0x1c00-0x1c07]
[    0.140903] pci 0000:00:1f.2: reg 14 io port: [0x18d4-0x18d7]
[    0.140909] pci 0000:00:1f.2: reg 18 io port: [0x18d8-0x18df]
[    0.140916] pci 0000:00:1f.2: reg 1c io port: [0x18d0-0x18d3]
[    0.140923] pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
[    0.140929] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf1104000-0xf11047ff]
[    0.140947] pci 0000:00:1f.2: PME# supported from D3hot
[    0.140950] pci 0000:00:1f.2: PME# disabled
[    0.141001] pci 0000:00:1f.3: reg 10 32bit mmio: [0x000000-0x0000ff]
[    0.141023] pci 0000:00:1f.3: reg 20 io port: [0x1c20-0x1c3f]
[    0.141257] pci 0000:02:00.0: reg 10 64bit mmio: [0xf0a00000-0xf0a0ffff]
[    0.141378] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.141389] pci 0000:02:00.0: PME# disabled
[    0.141989] pci 0000:00:1c.0: bridge io port: [0x2000-0x2fff]
[    0.141993] pci 0000:00:1c.0: bridge 32bit mmio: [0xf0a00000-0xf0afffff]
[    0.142000] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf0000000-0xf01fffff]
[    0.142052] pci 0000:00:1c.1: bridge io port: [0x3000-0x3fff]
[    0.142056] pci 0000:00:1c.1: bridge 32bit mmio: [0xf0b00000-0xf0bfffff]
[    0.142063] pci 0000:00:1c.1: bridge 64bit mmio pref: [0xf0200000-0xf03fffff]
[    0.142171] pci 0000:06:00.0: reg 10 64bit mmio: [0xf0c00000-0xf0c01fff]
[    0.142263] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[    0.142281] pci 0000:06:00.0: PME# disabled
[    0.142612] pci 0000:00:1c.2: bridge io port: [0x4000-0x4fff]
[    0.142616] pci 0000:00:1c.2: bridge 32bit mmio: [0xf0c00000-0xf0cfffff]
[    0.142623] pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf0400000-0xf05fffff]
[    0.142672] pci 0000:00:1c.3: bridge io port: [0x5000-0x5fff]
[    0.142676] pci 0000:00:1c.3: bridge 32bit mmio: [0xf0d00000-0xf0dfffff]
[    0.142683] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf0600000-0xf07fffff]
[    0.142735] pci 0000:0a:06.0: reg 10 32bit mmio: [0xf0e04000-0xf0e04fff]
[    0.142746] pci 0000:0a:06.0: supports D1 D2
[    0.142748] pci 0000:0a:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.142753] pci 0000:0a:06.0: PME# disabled
[    0.142795] pci 0000:0a:06.1: reg 10 32bit mmio: [0xf0e06000-0xf0e067ff]
[    0.142803] pci 0000:0a:06.1: reg 14 32bit mmio: [0xf0e00000-0xf0e03fff]
[    0.142845] pci 0000:0a:06.1: supports D1 D2
[    0.142846] pci 0000:0a:06.1: PME# supported from D0 D1 D2 D3hot
[    0.142851] pci 0000:0a:06.1: PME# disabled
[    0.142892] pci 0000:0a:06.2: reg 10 32bit mmio: [0xf0e05000-0xf0e05fff]
[    0.142939] pci 0000:0a:06.2: supports D1 D2
[    0.142940] pci 0000:0a:06.2: PME# supported from D0 D1 D2 D3hot
[    0.142945] pci 0000:0a:06.2: PME# disabled
[    0.142989] pci 0000:0a:06.3: reg 10 32bit mmio: [0xf0e06800-0xf0e068ff]
[    0.143036] pci 0000:0a:06.3: supports D1 D2
[    0.143037] pci 0000:0a:06.3: PME# supported from D0 D1 D2 D3hot
[    0.143042] pci 0000:0a:06.3: PME# disabled
[    0.143095] pci 0000:00:1e.0: transparent bridge
[    0.143102] pci 0000:00:1e.0: bridge 32bit mmio: [0xf0e00000-0xf0efffff]
[    0.143159] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.143578] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.143721] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.143861] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[    0.144007] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[    0.144164] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[    0.155310] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[    0.155310] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.155330] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[    0.155443] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.155549] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.155655] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.155760] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.155866] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.156044] ACPI: Power Resource [FN00] (off)
[    0.156166] SCSI subsystem initialized
[    0.156166] libata version 3.00 loaded.
[    0.156166] usbcore: registered new interface driver usbfs
[    0.156996] usbcore: registered new interface driver hub
[    0.156998] usbcore: registered new device driver usb
[    0.156998] PCI: Using ACPI for IRQ routing
[    0.164006] cfg80211: Using static regulatory domain info
[    0.164006] cfg80211: Regulatory domain: US
[    0.164006] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    0.164006] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[    0.164006] 	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.164006] 	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.164006] 	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.164006] 	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.164008] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[    0.164010] cfg80211: Calling CRDA for country: US
[    0.164026] NetLabel: Initializing
[    0.164026] NetLabel:  domain hash size = 128
[    0.164026] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.164026] NetLabel:  unlabeled traffic allowed by default
[    0.164026] PCI-GART: No AMD northbridge found.
[    0.164026] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.164029] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.178980] pnp: PnP ACPI init
[    0.178990] ACPI: bus type pnp registered
[    0.191515] pnp: PnP ACPI: found 13 devices
[    0.191517] ACPI: ACPI bus type pnp unregistered
[    0.191525] system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
[    0.191528] system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
[    0.191531] system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
[    0.191533] system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
[    0.191535] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[    0.191538] system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
[    0.191540] system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
[    0.191546] system 00:04: iomem range 0xfed00000-0xfed003ff could not be reserved
[    0.191555] system 00:06: ioport range 0x680-0x69f has been reserved
[    0.191557] system 00:06: ioport range 0x800-0x80f has been reserved
[    0.191559] system 00:06: ioport range 0x1000-0x107f has been reserved
[    0.191562] system 00:06: ioport range 0x1180-0x11bf has been reserved
[    0.191564] system 00:06: ioport range 0x1640-0x164f has been reserved
[    0.191566] system 00:06: ioport range 0xfe00-0xfe00 has been reserved
[    0.196610] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.196613] pci 0000:00:1c.0:   IO window: 0x2000-0x2fff
[    0.196619] pci 0000:00:1c.0:   MEM window: 0xf0a00000-0xf0afffff
[    0.196623] pci 0000:00:1c.0:   PREFETCH window: 0x000000f0000000-0x000000f01fffff
[    0.196630] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04
[    0.196633] pci 0000:00:1c.1:   IO window: 0x3000-0x3fff
[    0.196639] pci 0000:00:1c.1:   MEM window: 0xf0b00000-0xf0bfffff
[    0.196643] pci 0000:00:1c.1:   PREFETCH window: 0x000000f0200000-0x000000f03fffff
[    0.196650] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:06
[    0.196653] pci 0000:00:1c.2:   IO window: 0x4000-0x4fff
[    0.196658] pci 0000:00:1c.2:   MEM window: 0xf0c00000-0xf0cfffff
[    0.196663] pci 0000:00:1c.2:   PREFETCH window: 0x000000f0400000-0x000000f05fffff
[    0.196669] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:08
[    0.196672] pci 0000:00:1c.3:   IO window: 0x5000-0x5fff
[    0.196677] pci 0000:00:1c.3:   MEM window: 0xf0d00000-0xf0dfffff
[    0.196682] pci 0000:00:1c.3:   PREFETCH window: 0x000000f0600000-0x000000f07fffff
[    0.196691] pci 0000:0a:06.0: CardBus bridge, secondary bus 0000:0b
[    0.196693] pci 0000:0a:06.0:   IO window: 0x006000-0x0060ff
[    0.196697] pci 0000:0a:06.0:   IO window: 0x006400-0x0064ff
[    0.196702] pci 0000:0a:06.0:   PREFETCH window: 0x88000000-0x8bffffff
[    0.196707] pci 0000:0a:06.0:   MEM window: 0x90000000-0x93ffffff
[    0.196712] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
[    0.196715] pci 0000:00:1e.0:   IO window: 0x6000-0x6fff
[    0.196720] pci 0000:00:1e.0:   MEM window: 0xf0e00000-0xf0efffff
[    0.196724] pci 0000:00:1e.0:   PREFETCH window: 0x00000088000000-0x0000008bffffff
[    0.196739] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.196744] pci 0000:00:1c.0: setting latency timer to 64
[    0.196752] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    0.196756] pci 0000:00:1c.1: setting latency timer to 64
[    0.196765] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.196769] pci 0000:00:1c.2: setting latency timer to 64
[    0.196777] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.196781] pci 0000:00:1c.3: setting latency timer to 64
[    0.196788] pci 0000:00:1e.0: setting latency timer to 64
[    0.196796] pci 0000:0a:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.196802] bus: 00 index 0 io port: [0x00-0xffff]
[    0.196804] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
[    0.196806] bus: 02 index 0 io port: [0x2000-0x2fff]
[    0.196808] bus: 02 index 1 mmio: [0xf0a00000-0xf0afffff]
[    0.196810] bus: 02 index 2 mmio: [0xf0000000-0xf01fffff]
[    0.196811] bus: 02 index 3 mmio: [0x0-0x0]
[    0.196813] bus: 04 index 0 io port: [0x3000-0x3fff]
[    0.196815] bus: 04 index 1 mmio: [0xf0b00000-0xf0bfffff]
[    0.196816] bus: 04 index 2 mmio: [0xf0200000-0xf03fffff]
[    0.196818] bus: 04 index 3 mmio: [0x0-0x0]
[    0.196820] bus: 06 index 0 io port: [0x4000-0x4fff]
[    0.196821] bus: 06 index 1 mmio: [0xf0c00000-0xf0cfffff]
[    0.196823] bus: 06 index 2 mmio: [0xf0400000-0xf05fffff]
[    0.196825] bus: 06 index 3 mmio: [0x0-0x0]
[    0.196826] bus: 08 index 0 io port: [0x5000-0x5fff]
[    0.196828] bus: 08 index 1 mmio: [0xf0d00000-0xf0dfffff]
[    0.196830] bus: 08 index 2 mmio: [0xf0600000-0xf07fffff]
[    0.196831] bus: 08 index 3 mmio: [0x0-0x0]
[    0.196833] bus: 0a index 0 io port: [0x6000-0x6fff]
[    0.196835] bus: 0a index 1 mmio: [0xf0e00000-0xf0efffff]
[    0.196836] bus: 0a index 2 mmio: [0x88000000-0x8bffffff]
[    0.196838] bus: 0a index 3 io port: [0x00-0xffff]
[    0.196840] bus: 0a index 4 mmio: [0x000000-0xffffffffffffffff]
[    0.196842] bus: 0b index 0 io port: [0x6000-0x60ff]
[    0.196843] bus: 0b index 1 io port: [0x6400-0x64ff]
[    0.196845] bus: 0b index 2 mmio: [0x88000000-0x8bffffff]
[    0.196847] bus: 0b index 3 mmio: [0x90000000-0x93ffffff]
[    0.196856] NET: Registered protocol family 2
[    0.206385] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.207083] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[    0.208674] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.209204] TCP: Hash tables configured (established 262144 bind 65536)
[    0.209207] TCP reno registered
[    0.211397] NET: Registered protocol family 1
[    0.211524] checking if image is initramfs... it is
[    0.385695] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.449021] Freeing initrd memory: 3530k freed
[    0.450168] Simple Boot Flag at 0x36 set to 0x80
[    0.451099] audit: initializing netlink socket (disabled)
[    0.451114] type=2000 audit(1225232729.450:1): initialized
[    0.454048] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.456454] VFS: Disk quotas dquot_6.5.1
[    0.456526] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.457057] msgmni has been set to 4004
[    0.457154] SELinux:  Registering netfilter hooks
[    0.457501] alg: No test for stdrng (krng)
[    0.457596] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.457599] io scheduler noop registered
[    0.457600] io scheduler anticipatory registered
[    0.457602] io scheduler deadline registered
[    0.457702] io scheduler cfq registered (default)
[    0.457715] pci 0000:00:02.0: Boot video device
[    0.477771] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    0.477813] pcieport-driver 0000:00:1c.0: found MSI capability
[    0.477846] pcieport-driver 0000:00:1c.0: irq 47 for MSI/MSI-X
[    0.477860] pci_express 0000:00:1c.0:pcie00: allocate port service
[    0.477898] pci_express 0000:00:1c.0:pcie02: allocate port service
[    0.477932] pci_express 0000:00:1c.0:pcie03: allocate port service
[    0.478025] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[    0.478066] pcieport-driver 0000:00:1c.1: found MSI capability
[    0.478094] pcieport-driver 0000:00:1c.1: irq 46 for MSI/MSI-X
[    0.478108] pci_express 0000:00:1c.1:pcie00: allocate port service
[    0.478142] pci_express 0000:00:1c.1:pcie02: allocate port service
[    0.478174] pci_express 0000:00:1c.1:pcie03: allocate port service
[    0.478262] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[    0.478305] pcieport-driver 0000:00:1c.2: found MSI capability
[    0.478333] pcieport-driver 0000:00:1c.2: irq 45 for MSI/MSI-X
[    0.478347] pci_express 0000:00:1c.2:pcie00: allocate port service
[    0.478383] pci_express 0000:00:1c.2:pcie02: allocate port service
[    0.478417] pci_express 0000:00:1c.2:pcie03: allocate port service
[    0.478505] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[    0.478546] pcieport-driver 0000:00:1c.3: found MSI capability
[    0.478574] pcieport-driver 0000:00:1c.3: irq 44 for MSI/MSI-X
[    0.478588] pci_express 0000:00:1c.3:pcie00: allocate port service
[    0.478623] pci_express 0000:00:1c.3:pcie02: allocate port service
[    0.478655] pci_express 0000:00:1c.3:pcie03: allocate port service
[    0.478793] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.488382] ACPI: AC Adapter [ADP0] (on-line)
[    0.500274] Switched to high resolution mode on CPU 1
[    0.500952] Switched to high resolution mode on CPU 0
[    0.629204] ACPI: Battery Slot [BAT0] (battery present)
[    0.629373] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.629375] ACPI: Power Button (FF) [PWRF]
[    0.629444] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[    0.629489] ACPI: Lid Switch [LID]
[    0.629555] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[    0.629557] ACPI: Power Button (CM) [PWRB]
[    0.629681] ACPI: Transitioning device [FAN0] to D3
[    0.629721] fan PNP0C0B:00: registered as cooling_device0
[    0.629725] ACPI: Fan [FAN0] (off)
[    0.633457] ACPI: SSDT 7F6774B3, 027A (r1  PmRef  Cpu0Ist     3000 INTL 20050624)
[    0.633877] ACPI: SSDT 7F676F84, 04AA (r1  PmRef  Cpu0Cst     3001 INTL 20050624)
[    0.639376] Monitor-Mwait will be used to enter C-1 state
[    0.639378] Monitor-Mwait will be used to enter C-2 state
[    0.639381] Monitor-Mwait will be used to enter C-3 state
[    0.639420] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    0.639460] processor ACPI0007:00: registered as cooling_device1
[    0.639463] ACPI: Processor [CPU0] (supports 8 throttling states)
[    0.643418] ACPI: SSDT 7F67772D, 00C8 (r1  PmRef  Cpu1Ist     3000 INTL 20050624)
[    0.643738] ACPI: SSDT 7F67742E, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20050624)
[    0.649177] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[    0.649220] processor ACPI0007:01: registered as cooling_device2
[    0.649223] ACPI: Processor [CPU1] (supports 8 throttling states)
[    0.680247] thermal LNXTHERM:01: registered as thermal_zone0
[    0.710056] ACPI: Thermal Zone [TZ00] (49 C)
[    0.726136] thermal LNXTHERM:02: registered as thermal_zone1
[    0.756055] ACPI: Thermal Zone [TZ01] (0 C)
[    0.766133] thermal LNXTHERM:03: registered as thermal_zone2
[    0.786055] ACPI: Thermal Zone [TZ02] (0 C)
[    0.795576] Non-volatile memory driver v1.2
[    0.795578] Linux agpgart interface v0.103
[    0.795593] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[    0.796750] agpgart-intel 0000:00:00.0: detected 7676K stolen memory
[    0.799568] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    0.799658] [drm] Initialized drm 1.1.0 20060810
[    0.799722] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.799726] pci 0000:00:02.0: setting latency timer to 64
[    0.799872] [drm] Initialized i915 1.6.0 20080730 on minor 0
[    0.799894] intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM chipsets
[    0.799896] intelfb: Version 0.9.6
[    0.799926] intelfb: 00:02.0: Intel(R) 965GM, aperture size 256MB, stolen memory 7932kB
[    0.804665] intelfb: Non-CRT device is enabled ( LVDS port ).  Disabling mode switching.
[    0.804670] intelfb: Video mode must be programmed at boot time.
[    0.806679] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    0.808584] brd: module loaded
[    0.809275] loop: module loaded
[    0.809288] tg3.c:v3.94 (August 14, 2008)
[    0.809347] tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.809360] tg3 0000:02:00.0: setting latency timer to 64
[    0.818340] eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:a0:d1:c2:37:9a
[    0.818343] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[    0.818345] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    0.818472] Driver 'sd' needs updating - please use bus_type methods
[    0.818501] Driver 'sr' needs updating - please use bus_type methods
[    0.818581] ahci 0000:00:1f.2: version 3.0
[    0.818590] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.818624] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
[    0.818673] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[    0.818676] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck led clo pio slum part 
[    0.818680] ahci 0000:00:1f.2: setting latency timer to 64
[    0.818842] scsi0 : ahci
[    0.818963] scsi1 : ahci
[    0.819063] scsi2 : ahci
[    0.819208] ata1: SATA max UDMA/133 abar m2048@0xf1104000 port 0xf1104100 irq 43
[    0.819211] ata2: SATA max UDMA/133 abar m2048@0xf1104000 port 0xf1104180 irq 43
[    0.819214] ata3: SATA max UDMA/133 abar m2048@0xf1104000 port 0xf1104200 irq 43
[    1.124017] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.126660] ACPI Warning (nspredef-0852): \_SB_.PCI0.SATA.PRT0._GTF: Return type mismatch - found Integer, expected Buffer [20080926]
[    1.126667] ata1.00: _GTF unexpected object type 0x1
[    1.126742] ata1.00: ATA-8: SAMSUNG HM121HI, LZ100-08, max UDMA7
[    1.126744] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.129437] ata1.00: _GTF unexpected object type 0x1
[    1.129518] ata1.00: configured for UDMA/133
[    1.434014] ata2: SATA link down (SStatus 0 SControl 300)
[    1.460131] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    1.739014] ata3: SATA link down (SStatus 0 SControl 300)
[    1.739101] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM121HI  LZ10 PQ: 0 ANSI: 5
[    1.739277] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[    1.739292] sd 0:0:0:0: [sda] Write Protect is off
[    1.739294] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.739316] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.739376] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[    1.739389] sd 0:0:0:0: [sda] Write Protect is off
[    1.739391] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.739414] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.739417]  sda: sda1 sda2
[    1.762066] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.762149] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.762249] ata_piix 0000:00:1f.1: version 2.12
[    1.762256] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    1.762285] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.762342] scsi3 : ata_piix
[    1.762438] scsi4 : ata_piix
[    1.763118] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[    1.763121] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[    1.933343] ata4.00: ATAPI: TSSTcorp CDDVDW SN-S082H, SB00, max UDMA/33
[    1.955277] ata4.00: configured for UDMA/33
[    2.128023] isa bounce pool size: 16 pages
[    2.132305] scsi 3:0:0:0: CD-ROM            TSSTcorp CDDVDW SN-S082H  SB00 PQ: 0 ANSI: 5
[    2.143949] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.143951] Uniform CD-ROM driver Revision: 3.20
[    2.144083] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    2.144160] sr 3:0:0:0: Attached scsi generic sg1 type 5
[    2.144412] usbcore: registered new interface driver usblp
[    2.144415] Initializing USB Mass Storage driver...
[    2.144449] usbcore: registered new interface driver usb-storage
[    2.144451] USB Mass Storage support registered.
[    2.144487] usbcore: registered new interface driver libusual
[    2.144586] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    2.146507] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.146512] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.146561] mice: PS/2 mouse device common for all mice
[    2.156416] rtc_cmos 00:08: RTC can wake from S4
[    2.156471] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[    2.156498] rtc0: alarms up to one month, y3k, 242 bytes nvram, , hpet irqs irqs
[    2.156542] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    2.156545] ACPI: I/O resource 0000:00:1f.3 [0x1c20-0x1c3f] conflicts with ACPI region SMBI [0x1c20-0x1c2f]
[    2.156547] ACPI: Device needs an ACPI driver
[    2.156880] device-mapper: uevent: version 1.0.3
[    2.156990] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    2.157242] cpuidle: using governor ladder
[    2.157702] cpuidle: using governor menu
[    2.157754] Marking TSC unstable due to TSC halts in idle
[    2.158640] usbcore: registered new interface driver hiddev
[    2.158683] usbcore: registered new interface driver usbhid
[    2.158685] usbhid: v2.6:USB HID core driver
[    2.158742] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
[    2.159661] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    2.159697] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    2.176839] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    2.216443] ALSA device list:
[    2.216445]   #0: HDA Intel at 0xf0f00000 irq 22
[    2.216520] Netfilter messages via NETLINK v0.30.
[    2.216534] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    2.216839] ctnetlink v0.93: registering with nfnetlink.
[    2.217400] ip_tables: (C) 2000-2006 Netfilter Core Team
[    2.217422] TCP cubic registered
[    2.217423] Initializing XFRM netlink socket
[    2.217534] NET: Registered protocol family 10
[    2.218413] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    2.218461] IPv6 over IPv4 tunneling driver
[    2.219065] NET: Registered protocol family 17
[    2.219647] registered taskstats version 1
[    2.219815] rtc_cmos 00:08: setting system clock to 2008-10-28 22:25:31 UTC (1225232731)
[    2.219861] Freeing unused kernel memory: 480k freed
[    2.220036] Write protecting the kernel read-only data: 5552k
[    2.584920] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    2.617079] Clocksource tsc unstable (delta = -249629513 ns)
[    2.639421] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.639477] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.639546] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    2.639553] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    2.639727] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    2.643649] ehci_hcd 0000:00:1a.7: debug port 1
[    2.643661] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    2.643691] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf1104800
[    2.653090] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    2.653242] usb usb1: configuration #1 chosen from 1 choice
[    2.653322] hub 1-0:1.0: USB hub found
[    2.653335] hub 1-0:1.0: 4 ports detected
[    2.653557] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.653564] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.653569] usb usb1: Product: EHCI Host Controller
[    2.653573] usb usb1: Manufacturer: Linux 2.6.28-rc2 ehci_hcd
[    2.653578] usb usb1: SerialNumber: 0000:00:1a.7
[    2.653617] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.653641] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.653648] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.653763] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    2.657686] ehci_hcd 0000:00:1d.7: debug port 1
[    2.657698] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    2.657720] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf1104c00
[    2.667332] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.667467] usb usb2: configuration #1 chosen from 1 choice
[    2.667535] hub 2-0:1.0: USB hub found
[    2.667547] hub 2-0:1.0: 6 ports detected
[    2.667746] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    2.667752] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.667757] usb usb2: Product: EHCI Host Controller
[    2.667761] usb usb2: Manufacturer: Linux 2.6.28-rc2 ehci_hcd
[    2.667766] usb usb2: SerialNumber: 0000:00:1d.7
[    2.672972] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.678318] uhci_hcd: USB Universal Host Controller Interface driver
[    2.678390] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.678405] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    2.678413] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    2.678546] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    2.678600] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[    2.678772] usb usb3: configuration #1 chosen from 1 choice
[    2.678838] hub 3-0:1.0: USB hub found
[    2.678851] hub 3-0:1.0: 2 ports detected
[    2.679048] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.679054] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.679059] usb usb3: Product: UHCI Host Controller
[    2.679063] usb usb3: Manufacturer: Linux 2.6.28-rc2 uhci_hcd
[    2.679067] usb usb3: SerialNumber: 0000:00:1a.0
[    2.679107] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    2.679120] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    2.679126] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    2.679245] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    2.679303] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[    2.679467] usb usb4: configuration #1 chosen from 1 choice
[    2.679533] hub 4-0:1.0: USB hub found
[    2.679545] hub 4-0:1.0: 2 ports detected
[    2.679708] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.679714] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.679719] usb usb4: Product: UHCI Host Controller
[    2.679723] usb usb4: Manufacturer: Linux 2.6.28-rc2 uhci_hcd
[    2.679728] usb usb4: SerialNumber: 0000:00:1a.1
[    2.679767] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.679779] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.679786] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.679907] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[    2.679944] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[    2.680122] usb usb5: configuration #1 chosen from 1 choice
[    2.680192] hub 5-0:1.0: USB hub found
[    2.680205] hub 5-0:1.0: 2 ports detected
[    2.680383] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    2.680389] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.680394] usb usb5: Product: UHCI Host Controller
[    2.680398] usb usb5: Manufacturer: Linux 2.6.28-rc2 uhci_hcd
[    2.680402] usb usb5: SerialNumber: 0000:00:1d.0
[    2.680438] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.680450] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.680457] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.680563] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[    2.680613] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[    2.680781] usb usb6: configuration #1 chosen from 1 choice
[    2.680842] hub 6-0:1.0: USB hub found
[    2.680856] hub 6-0:1.0: 2 ports detected
[    2.681047] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.681052] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.681057] usb usb6: Product: UHCI Host Controller
[    2.681062] usb usb6: Manufacturer: Linux 2.6.28-rc2 uhci_hcd
[    2.681066] usb usb6: SerialNumber: 0000:00:1d.1
[    2.681101] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.681113] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.681120] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.681229] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[    2.681267] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[    2.681441] usb usb7: configuration #1 chosen from 1 choice
[    2.681500] hub 7-0:1.0: USB hub found
[    2.681514] hub 7-0:1.0: 2 ports detected
[    2.681696] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    2.681702] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.681706] usb usb7: Product: UHCI Host Controller
[    2.681711] usb usb7: Manufacturer: Linux 2.6.28-rc2 uhci_hcd
[    2.681715] usb usb7: SerialNumber: 0000:00:1d.2
[    2.783649] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000
[    2.816927] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input4
[    3.776829] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    7.885012] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    8.897241] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    8.961139] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   10.990087] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   12.008342] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   13.021339] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   14.082587] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   15.101436] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   16.119125] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   26.390333] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   27.414387] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   28.432079] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   29.444281] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   30.509645] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   43.657138] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   43.711625] kjournald starting.  Commit interval 5 seconds
[   43.711646] EXT3-fs: mounted filesystem with ordered data mode.
[   43.822300] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   43.855228] type=1404 audit(1225232773.135:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[   43.925988] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   44.198434] SELinux: 8192 avtab hash slots, 176373 rules.
[   44.246178] SELinux: 8192 avtab hash slots, 176373 rules.
[   44.288794] SELinux:  8 users, 12 roles, 2402 types, 117 bools, 1 sens, 1024 cats
[   44.288798] SELinux:  73 classes, 176373 rules
[   44.291584] SELinux:  Completing initialization.
[   44.291585] SELinux:  Setting up existing superblocks.
[   44.295225] SELinux: initialized (dev dm-1, type ext3), uses xattr
[   44.295296] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[   44.295308] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   44.295691] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[   44.295720] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
[   44.295733] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
[   44.295737] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[   44.295750] SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
[   44.295753] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   44.295765] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
[   44.295768] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[   44.295774] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[   44.295825] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[   44.295830] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[   44.295846] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
[   44.295849] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[   44.295930] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[   44.318020] type=1403 audit(1225232773.597:3): policy loaded auid=4294967295 ses=4294967295
[   44.842269] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   44.842292] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   45.342283] ACPI: EC: missing confirmations, switch off interrupt mode.
[   49.971369] tifm_7xx1 0000:0a:06.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   50.122863] tpm_inf_pnp 00:0a: Found TPM with ID IFX0102
[   50.122910] tpm_inf_pnp 00:0a: TPM found: config base 0x4e, data base 0x1670, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
[   50.122973] SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
[   50.329043] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[   50.329045] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[   50.329154] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   50.329167] iwlagn 0000:06:00.0: setting latency timer to 64
[   50.329230] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[   50.379421] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
[   50.379622] iwlagn 0000:06:00.0: PCI INT A disabled
[   50.380391] phy0: Selected rate control algorithm 'iwl-agn-rs'
[   50.519270] NET: Registered protocol family 23
[   50.551267] hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x023b8000
[   50.560484] ohci1394 0000:0a:06.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   50.597393] nsc-ircc 00:09: disabled
[   50.611219] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]  MMIO=[f0e06000-f0e067ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[   51.287060] device-mapper: multipath: version 1.0.5 loaded
[   53.699473] EXT3 FS on dm-1, internal journal
[   53.927201] kjournald starting.  Commit interval 5 seconds
[   53.927737] EXT3 FS on dm-3, internal journal
[   53.927748] EXT3-fs: mounted filesystem with ordered data mode.
[   53.934781] SELinux: initialized (dev dm-3, type ext3), uses xattr
[   53.995658] kjournald starting.  Commit interval 5 seconds
[   53.996190] EXT3 FS on dm-4, internal journal
[   53.996199] EXT3-fs: mounted filesystem with ordered data mode.
[   54.004514] SELinux: initialized (dev dm-4, type ext3), uses xattr
[   54.088644] kjournald starting.  Commit interval 5 seconds
[   54.089130] EXT3 FS on dm-2, internal journal
[   54.089141] EXT3-fs: mounted filesystem with ordered data mode.
[   54.097828] SELinux: initialized (dev dm-2, type ext3), uses xattr
[   54.100195] kjournald starting.  Commit interval 5 seconds
[   54.100507] EXT3 FS on sda1, internal journal
[   54.100516] EXT3-fs: mounted filesystem with ordered data mode.
[   54.117166] SELinux: initialized (dev sda1, type ext3), uses xattr
[   54.117658] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   56.237114] SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
[   90.961234] Adding 2031608k swap on /dev/mapper/master-swap.  Priority:-1 extents:1 across:2031608k
[   90.967421] SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
[   91.621098] platform microcode: firmware: requesting intel-ucode/06-0f-0a
[   91.669783] platform microcode: firmware: requesting intel-ucode/06-0f-0a
[   91.677059] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk> <peter.oruba@amd.com>
[   91.851359] microcode: CPU0 updated from revision 0x91 to 0x92, date = 2007-03-13 
[   91.852599] microcode: CPU1 updated from revision 0x91 to 0x92, date = 2007-03-13 
[   91.862496] Microcode Update Driver: v2.00 removed.
[   93.895533] RPC: Registered udp transport module.
[   93.895535] RPC: Registered tcp transport module.
[   93.897729] SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
[   96.058936] warning: `dbus-daemon' uses deprecated v2 capabilities in a way that may be insecure.
[   96.294460] fuse init (API version 7.10)
[   96.305731] SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
[  101.255971] Bluetooth: Core ver 2.13
[  101.256165] NET: Registered protocol family 31
[  101.256170] Bluetooth: HCI device and connection manager initialized
[  101.256176] Bluetooth: HCI socket layer initialized
[  101.299088] Bluetooth: L2CAP ver 2.11
[  101.299094] Bluetooth: L2CAP socket layer initialized
[  101.435849] Bluetooth: RFCOMM socket layer initialized
[  101.435869] Bluetooth: RFCOMM TTY layer initialized
[  101.435873] Bluetooth: RFCOMM ver 1.10
[  101.764617] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[  101.764623] Bluetooth: BNEP filters: protocol multicast
[  104.513132] tg3 0000:02:00.0: irq 42 for MSI/MSI-X
[  104.593985] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  104.622611] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[  104.622746] iwlagn 0000:06:00.0: restoring config space at offset 0x1 (was 0x40100102, writing 0x40100106)
[  104.622909] iwlagn 0000:06:00.0: irq 41 for MSI/MSI-X
[  104.623083] iwlagn 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
[  104.925882] Registered led device: iwl-phy0:radio
[  104.925926] Registered led device: iwl-phy0:assoc
[  104.925974] Registered led device: iwl-phy0:RX
[  104.926014] Registered led device: iwl-phy0:TX
[  104.958877] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  106.193954] tg3: eth0: Link is up at 100 Mbps, full duplex.
[  106.193961] tg3: eth0: Flow control is on for TX and on for RX.
[  106.195266] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  117.920085] eth0: no IPv6 routers present
[  158.370332] [drm:i915_get_vblank_counter] *ERROR* trying to get vblank count for disabled pipe 0
[  160.621285] SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
[  177.903994] wlan0: direct probe to AP 00:c0:a8:e5:e5:a5 try 1
[  177.907452] wlan0 direct probe responded
[  177.907456] wlan0: authenticate with AP 00:c0:a8:e5:e5:a5
[  177.909236] wlan0: authenticated
[  177.909239] wlan0: associate with AP 00:c0:a8:e5:e5:a5
[  177.916566] wlan0: RX AssocResp from 00:c0:a8:e5:e5:a5 (capab=0x431 status=0 aid=1)
[  177.916568] wlan0: associated
[  177.939913] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  188.454268] wlan0: no IPv6 routers present

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Johannes Berg]

[-- Attachment #1: Type: text/plain, Size: 351 bytes --]

On Tue, 2008-10-28 at 23:58 +0100, Mirco Tischler wrote:
> On Tue, 28 Oct 2008 19:36:34 +0100, Johannes Berg wrote:
> > Can we have a dmesg output with the "TX power requested" line posted
> > here?

> You mean the hole output? Cause I posted the wireless part in my initial mail.

Sorry, I got confused, the initial mail is fine.

johannes

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 1686 bytes --]

In between I found out that suspend and hibernation are broken too. I would
open a new thread but in the "Suspend to RAM regression in 2.6.28-rc2
(bisected)" thread that handled a similar problem iwlwifi was blamed, at least
in the mails I read. So maybe this is related here too.

The machine suspends and hibernates fine, but doesn't wake up anymore correctly.
On hibernation I end up with a black screen and only the mouse which I can
still move. But anything else is locked up. I can't switch to virtual console
with ctrl+alt+f? nor can I restart the xserver. I can't even connect on
network. The only thing I can do is move the mouse on a black screen or push
the power button.

On suspend it is a little better. After wakeup I see the frames of the windows
but not the content, and the gnome panel. And again I can move the mouse but I
can't interact with anything. At least I can connect over network using ssh.
But processes like compiz don't respond to kill -9 PID and when I try to kill
Xorg the machine completely locks up.

Another thing that I just noticed is very slow boot. From startup of udev until
short before X starts the boot lasts minutes. What I noticed is that there are
long phases of no hard disk activity. And I don't really  have the heart to
write this but I have the impression that keyboard activity (i.e. pressing
random keys) causes the harddisk to read again and the hole boot to go on.

Sorry for this long subjective description of symptoms only without any
kernel messages or anything but that's all I can deliver at the moment. Maybe
tomorrow I find more than only half an hour to dig into this.

Thanks again

Mirco

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Zhu Yi]

[-- Attachment #1: Type: text/plain, Size: 468 bytes --]

On Wed, 2008-10-29 at 00:24 +0800, Mirco Tischler wrote:
> 
> I tested it quickly and not very thoroughly on the wpa-eap encrypted
> network at
> university and it showed the same behaviour: no connection without
> CONFIG_WIRELESS_OLD_REGULATORY and no problems with it enabled.

Interesting. The only difference between without and with
CONFIG_WIRELESS_OLD_REGULATORY is the txpower is lower and you can only
do passive scan. Can you try attached patch?

Thanks,
-yi

[-- Attachment #2: iwlwifi-oldreg-debug.patch --]
[-- Type: text/x-patch, Size: 888 bytes --]

diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c
index 0953a9c..8123156 100644
--- a/drivers/net/wireless/iwlwifi/iwl-4965.c
+++ b/drivers/net/wireless/iwlwifi/iwl-4965.c
@@ -1523,6 +1523,7 @@ static int iwl4965_send_tx_power(struct iwl_priv *priv)
 		 * the stack trace to find out who is calling this during
 		 * a scan. */
 		IWL_WARNING("TX Power requested while scanning!\n");
+		dump_stack();
 		return -EAGAIN;
 	}
 
diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index 5dab72d..7ffa736 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -71,9 +71,7 @@ static const struct ieee80211_regdomain world_regdom = {
 	.n_reg_rules = 1,
 	.alpha2 =  "00",
 	.reg_rules = {
-		REG_RULE(2412-10, 2462+10, 40, 6, 20,
-			NL80211_RRF_PASSIVE_SCAN |
-			NL80211_RRF_NO_IBSS),
+		REG_RULE(2412-10, 2462+10, 40, 6, 27, 0),
 	}
 };
 

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 3013 bytes --]

On Wed, 29 Oct 2008 14:18:04 +0800, Zhu Yi wrote:
> Can you try attached patch?
> 
> Thanks,
> -yi
I did. Didn't solve the problems but here's the output:
[  880.195147] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux,1.3.27kds 
[  880.195150] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[  880.195300] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[  880.195327] iwlagn 0000:06:00.0: setting latency timer to 64
[  880.195444] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[  880.245264] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
[  880.247969] phy3: Selected rate control algorithm 'iwl-agn-rs'
[  884.274477] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[  884.275247] iwlagn 0000:06:00.0: irq 41 for MSI/MSI-X
[  884.275361] iwlagn 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
[  884.489886] Registered led device: iwl-phy3:radio
[  884.489933] Registered led device: iwl-phy3:assoc
[  884.489973] Registered led device: iwl-phy3:RX
[  884.490012] Registered led device: iwl-phy3:TX
[  884.526082] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  884.784601] iwlagn: TX Power requested while scanning!
[  884.784611] Pid: 9839, comm: iwlagn/1 Not tainted 2.6.28-rc2-oldreg-debug #27
[  884.784617] Call Trace:
[  884.784632]  [<ffffffff8101a374>] ? native_smp_send_reschedule+0x4d/0x4f
[  884.784658]  [<ffffffffa01c1082>] iwl4965_send_tx_power+0x5a/0xf2f [iwlagn]
[  884.784668]  [<ffffffff813c065c>] ? _spin_unlock_irqrestore+0x31/0x3c
[  884.784677]  [<ffffffff8103341f>] ? try_to_wake_up+0x222/0x234
[  884.784685]  [<ffffffff8103343e>] ? default_wake_function+0xd/0xf
[  884.784693]  [<ffffffff8104ace2>] ? autoremove_wake_function+0x11/0x38
[  884.784703]  [<ffffffff8102aee1>] ? __wake_up_common+0x46/0x76
[  884.784710]  [<ffffffff813c065c>] ? _spin_unlock_irqrestore+0x31/0x3c
[  884.784717]  [<ffffffff8102c04f>] ? __wake_up+0x43/0x4f
[  884.784725]  [<ffffffff81047dff>] ? queue_work+0x59/0x68
[  884.784735]  [<ffffffff81395eab>] ?ieee80211_mlme_notify_scan_completed+0xc7/0xd9 
[  884.784743]  [<ffffffff81393708>] ? ieee80211_scan_completed+0x2e8/0x32c
[  884.784770]  [<ffffffffa00d5425>] ? iwl_rx_queue_restock+0xc6/0x143 [iwlcore]
[  884.784790]  [<ffffffffa00cf290>] iwl_set_tx_power+0x6b/0x71 [iwlcore]
[  884.784812]  [<ffffffffa00de3f6>] iwl_bg_scan_completed+0xbc/0xcd [iwlcore]
[  884.784834]  [<ffffffffa00de33a>] ? iwl_bg_scan_completed+0x0/0xcd [iwlcore]
[  884.784842]  [<ffffffff81047298>] run_workqueue+0x95/0x138
[  884.784849]  [<ffffffff81047430>] worker_thread+0xf5/0x109 
[  884.784856]  [<ffffffff8104acd1>] ? autoremove_wake_function+0x0/0x38
[  884.784864]  [<ffffffff8104733b>] ? worker_thread+0x0/0x109
[  884.784871]  [<ffffffff8104a956>] kthread+0x49/0x76 
[  884.784879]  [<ffffffff8100d129>] child_rip+0xa/0x11 
[  884.784886]  [<ffffffff8104a90d>] ? kthread+0x0/0x76 
[  884.784892]  [<ffffffff8100d11f>] ? child_rip+0x0/0x11

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[reinette chatre]

On Thu, 2008-10-30 at 10:24 -0700, Mirco Tischler wrote:
> On Wed, 29 Oct 2008 14:18:04 +0800, Zhu Yi wrote:
> > Can you try attached patch?
> > 
> > Thanks,
> > -yi
> I did. Didn't solve the problems but here's the output:

That helped us to obtain more information. Could you please try commit
9685e33a2c919c1e95cb7072988fc1e0f0bad3d9 ?

Reproduced here for convenience:

commit 9685e33a2c919c1e95cb7072988fc1e0f0bad3d9
Author: Mohamed Abbas <mohamed.abbas@intel.com>
Date:   Thu Oct 23 23:48:54 2008 -0700

    iwlwifi: clear scanning bits upon failure
    
    In iwl_bg_request_scan function, if we could not send a
    scan command it will go to done.
    In done it does the right thing to call mac80211 with
    scan complete, but the problem is STATUS_SCAN_HW is still
    set causing any future scan to fail. Fix by clearing the scanning status
    bits if scan fails.
    
    Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
    Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
    Signed-off-by: John W. Linville <linville@tuxdriver.com>

diff --git a/drivers/net/wireless/iwlwifi/iwl-scan.c b/drivers/net/wireless/iwlwifi/iwl-scan.c
index 3379b41..b0abf89 100644
--- a/drivers/net/wireless/iwlwifi/iwl-scan.c
+++ b/drivers/net/wireless/iwlwifi/iwl-scan.c
@@ -834,6 +834,13 @@ static void iwl_bg_request_scan(struct work_struct *data)
 	return;
 
  done:
+	/* Cannot perform scan. Make sure we clear scanning
+	* bits from status so next scan request can be performed.
+	* If we don't clear scanning status bit here all next scan
+	* will fail
+	*/
+	clear_bit(STATUS_SCAN_HW, &priv->status);
+	clear_bit(STATUS_SCANNING, &priv->status);
 	/* inform mac80211 scan aborted */
 	queue_work(priv->workqueue, &priv->scan_completed);
 	mutex_unlock(&priv->mutex);

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 235 bytes --]

On Thu, 30 Oct 2008 10:55:38 -0700, reinette chatre wrote:
> 
> That helped us to obtain more information. Could you please try commit
> 9685e33a2c919c1e95cb7072988fc1e0f0bad3d9 ?
> 
Solves the problem for me.

Thanks

Mirco

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]

Re: [2.6.28-rc2]: iwl4965 doesn't connect / cfg80211 failure

[Mirco Tischler]

[-- Attachment #1: Type: text/plain, Size: 1923 bytes --]

On Tue, 28 Oct 2008 02:02:12 +0100, Mirco Tischler wrote:
> Hi
> 
> I have problems connecting to wlan with my iwl4965 chip and 2.6.28-rc2 (didn't
> test -rc1). Networkmanager just times out every time.
> Only after playing around with rmmod/modprobe and killswitch I am sometimes
> able to connect. But I cannot reproduce this reliably yet.
> 
> This is what I get in dmesg (from modprobe iwlagn to connection failure):
> 
> [ 1881.884690] iwlagn: Intel(R) Wireless WiFi Link AGN driver for
> Linux,1.3.27kds
> [ 1881.884692] iwlagn: Copyright(c) 2003-2008 Intel Corporation
> [ 1881.884809] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 1881.884836] iwlagn 0000:06:00.0: setting latency timer to 64
> [ 1881.884952] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
> [ 1881.935149] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
> [ 1881.936327] phy4: Selected rate control algorithm 'iwl-agn-rs'
> [ 1885.965591] iwlagn 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 1885.965874] iwlagn 0000:06:00.0: irq 41 for MSI/MSI-X
> [ 1885.965974] iwlagn 0000:06:00.0: firmware: requesting iwlwifi-4965-2.ucode
> [ 1886.181600] Registered led device: iwl-phy4:radio
> [ 1886.181618] Registered led device: iwl-phy4:assoc
> [ 1886.181635] Registered led device: iwl-phy4:RX
> [ 1886.181654] Registered led device: iwl-phy4:TX
> [ 1886.213631] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 1887.572768] iwlagn: TX Power requested while scanning!
> 
> What might be related is this early on boot:
> 
> [    0.163009] cfg80211: Calling CRDA to update world regulatory domain
> [    0.163012] cfg80211: Failed calling CRDA
> [    0.163024] cfg80211: calling CRDA failed - unable to update world
> regulatory domain, using static definition
> 
> Need any further info?
> 
> thanks
> 
> Mirco
Resubmit because of broken email header.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 197 bytes --]