LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
To: "Mark Brown" <broonie@kernel.org>,
"Michal Simek" <michal.simek@xilinx.com>,
"Sören Brinkmann" <soren.brinkmann@xilinx.com>,
linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Subject: [PATCH 09/18] spi/xilinx: Do not inhibit transmission in polling mode
Date: Fri, 23 Jan 2015 17:08:41 +0100 [thread overview]
Message-ID: <1422029330-10971-10-git-send-email-ricardo.ribalda@gmail.com> (raw)
In-Reply-To: <1422029330-10971-1-git-send-email-ricardo.ribalda@gmail.com>
When no irq is used, there is no need to inhibit the transmission for
every transaction. This inhibition was implemented to avoid a race
condition with the irq handler.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
---
drivers/spi/spi-xilinx.c | 25 +++++++++++++++----------
1 file changed, 15 insertions(+), 10 deletions(-)
diff --git a/drivers/spi/spi-xilinx.c b/drivers/spi/spi-xilinx.c
index 8a28cab..a70cb91 100644
--- a/drivers/spi/spi-xilinx.c
+++ b/drivers/spi/spi-xilinx.c
@@ -163,6 +163,7 @@ static void xspi_rx32(struct xilinx_spi *xspi)
static void xspi_init_hw(struct xilinx_spi *xspi)
{
void __iomem *regs_base = xspi->regs;
+ u32 inhibit;
/* Reset the SPI device */
xspi->write_fn(XIPIF_V123B_RESET_MASK,
@@ -173,16 +174,19 @@ static void xspi_init_hw(struct xilinx_spi *xspi)
xspi->write_fn(XSPI_INTR_TX_EMPTY,
regs_base + XIPIF_V123B_IIER_OFFSET);
/* Enable the global IPIF interrupt */
- if (xspi->irq >= 0)
+ if (xspi->irq >= 0) {
xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
regs_base + XIPIF_V123B_DGIER_OFFSET);
- else
+ inhibit = XSPI_CR_TRANS_INHIBIT;
+ } else {
xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
+ inhibit = 0;
+ }
/* Deselect the slave on the SPI bus */
xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
/* Disable the transmitter, enable Manual Slave Select Assertion,
* put SPI controller into master mode, and enable it */
- xspi->write_fn(XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT |
+ xspi->write_fn(inhibit | XSPI_CR_MANUAL_SSELECT |
XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET |
XSPI_CR_RXFIFO_RESET, regs_base + XSPI_CR_OFFSET);
}
@@ -252,7 +256,7 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
reinit_completion(&xspi->done);
while (xspi->remaining_bytes) {
- u16 cr;
+ u16 cr = 0;
int n_words;
n_words = (xspi->remaining_bytes * 8) / xspi->bits_per_word;
@@ -263,13 +267,13 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
/* Start the transfer by not inhibiting the transmitter any
* longer
*/
- cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) &
- ~XSPI_CR_TRANS_INHIBIT;
- xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
- if (xspi->irq >= 0)
+ if (xspi->irq >= 0) {
+ cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) &
+ ~XSPI_CR_TRANS_INHIBIT;
+ xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
wait_for_completion(&xspi->done);
- else
+ } else
while (!(xspi->read_fn(xspi->regs + XSPI_SR_OFFSET) &
XSPI_SR_TX_EMPTY_MASK))
;
@@ -279,7 +283,8 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
* transmitter while the Isr refills the transmit register/FIFO,
* or make sure it is stopped if we're done.
*/
- xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
+ if (xspi->irq >= 0)
+ xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
xspi->regs + XSPI_CR_OFFSET);
/* Read out all the data from the Rx FIFO */
--
2.1.4
next prev parent reply other threads:[~2015-01-23 16:12 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-23 16:08 [PATCH 00/18] spi/xilinx: Speed-up Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 01/18] spi/xilinx: Support for spi mode LSB_FIRST Ricardo Ribalda Delgado
2015-01-26 19:23 ` Mark Brown
2015-01-23 16:08 ` [PATCH 02/18] spi/xilinx: Support for spi mode LOOP Ricardo Ribalda Delgado
2015-01-26 19:23 ` Mark Brown
2015-01-23 16:08 ` [PATCH 03/18] spi/xilinx: Simplify data read from the Rx FIFO Ricardo Ribalda Delgado
2015-01-27 17:25 ` Mark Brown
2015-01-23 16:08 ` [PATCH 04/18] spi-xilinx: Simplify spi_fill_tx_fifo Ricardo Ribalda Delgado
2015-01-26 23:54 ` Mark Brown
2015-01-23 16:08 ` [PATCH 05/18] spi/xilinx: Leave the IRQ always enabled Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 06/18] spi/xilinx: Code cleanup Ricardo Ribalda Delgado
2015-01-27 0:05 ` Mark Brown
2015-01-23 16:08 ` [PATCH 07/18] spi/xilinx: Use cached value of register Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 08/18] spi/xilinx: Support cores with no interrupt Ricardo Ribalda Delgado
2015-01-27 0:04 ` Mark Brown
2015-01-27 19:05 ` Ricardo Ribalda Delgado
2015-01-27 19:49 ` Mark Brown
2015-01-27 19:56 ` Ricardo Ribalda Delgado
2015-01-23 16:08 ` Ricardo Ribalda Delgado [this message]
2015-01-23 16:08 ` [PATCH 10/18] spi/xilinx: Support for spi mode CS_HIGH Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 11/18] spi/xilinx: Remove rx_fn and tx_fn pointer Ricardo Ribalda Delgado
2015-01-27 0:09 ` Mark Brown
2015-01-27 10:00 ` Ricardo Ribalda Delgado
2015-01-27 15:42 ` Joe Perches
2015-01-27 19:07 ` Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 12/18] spi/xilinx: Make spi_tx and spi_rx simmetric Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 13/18] spi/xilinx: Convert remainding_bytes in remaining words Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 14/18] spi/xilinx: Convert bits_per_word in bytes_per_word Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 15/18] spi/xilinx: Remove iowrite/ioread wrappers Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 16/18] spi/xilinx: Reset core before buffer_size detection Ricardo Ribalda Delgado
2015-01-27 0:11 ` Mark Brown
2015-01-23 16:08 ` [PATCH 17/18] spi/xilinx: Remove remaining_words driver data variable Ricardo Ribalda Delgado
2015-01-23 16:08 ` [PATCH 18/18] spi/xilinx: Check number of slaves range Ricardo Ribalda Delgado
2015-01-27 0:14 ` [PATCH 00/18] spi/xilinx: Speed-up Mark Brown
2015-01-27 10:17 ` Ricardo Ribalda Delgado
2015-01-27 11:59 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1422029330-10971-10-git-send-email-ricardo.ribalda@gmail.com \
--to=ricardo.ribalda@gmail.com \
--cc=broonie@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=michal.simek@xilinx.com \
--cc=soren.brinkmann@xilinx.com \
--subject='Re: [PATCH 09/18] spi/xilinx: Do not inhibit transmission in polling mode' \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).