[PATCH V3 1/4] ARM: dts: imx6sx-sabreauto: add PMIC support

[PATCH V3 1/4] ARM: dts: imx6sx-sabreauto: add PMIC support

[Anson Huang]

Add pfuze100 support on i.MX6SX Sabre Auto board.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
no changes since V2.
 arch/arm/boot/dts/imx6sx-sabreauto.dts | 117 +++++++++++++++++++++++++++++++++
 1 file changed, 117 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
index 57d1ea0..2caca934 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -74,6 +74,14 @@
 
 &iomuxc {
 	imx6x-sabreauto {
+
+		pinctrl_i2c2_1: i2c2grp-1 {
+			fsl,pins = <
+				MX6SX_PAD_GPIO1_IO03__I2C2_SDA          0x4001b8b1
+				MX6SX_PAD_GPIO1_IO02__I2C2_SCL          0x4001b8b1
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
@@ -148,3 +156,112 @@
 		};
 	};
 };
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2_1>;
+	status = "okay";
+
+	pmic: pfuze100@08 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
-- 
2.7.4

[PATCH V3 2/4] ARM: dts: imx6sx-sabreauto: add max7322 IO expander support

[Anson Huang]

Add MAX7322 IO expander support.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
no changes since V2.
 arch/arm/boot/dts/imx6sx-sabreauto.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
index 2caca934..d59084f 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -163,6 +163,13 @@
 	pinctrl-0 = <&pinctrl_i2c2_1>;
 	status = "okay";
 
+	max7322: gpio@68 {
+		compatible = "maxim,max7322";
+		reg = <0x68>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	pmic: pfuze100@08 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
-- 
2.7.4

[PATCH V3 3/4] ARM: dts: imx6sx-sabreauto: add IO expander max7310 support

[Anson Huang]

i.MX6SX Sabre Auto board has two max7310 IO expander
on I2C3 bus, add support for them.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
no changes since V2.
 arch/arm/boot/dts/imx6sx-sabreauto.dts | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
index d59084f..812f40b 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -82,6 +82,13 @@
 			>;
 		};
 
+		pinctrl_i2c3_2: i2c3grp-2 {
+			fsl,pins = <
+				MX6SX_PAD_KEY_ROW4__I2C3_SDA            0x4001b8b1
+				MX6SX_PAD_KEY_COL4__I2C3_SCL            0x4001b8b1
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
@@ -272,3 +279,24 @@
 		};
 	};
 };
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_2>;
+	status = "okay";
+
+	max7310_a: gpio@30 {
+		compatible = "maxim,max7310";
+		reg = <0x30>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	max7310_b: gpio@32 {
+		compatible = "maxim,max7310";
+		reg = <0x32>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
-- 
2.7.4

[PATCH V3 4/4] ARM: dts: imx6sx-sabreauto: add wdog external reset support

[Anson Huang]

i.MX6SX Sabre Auto board has GPIO1_IO13 pin can be
MUXed as WDOG output to reset PMIC, add this function
support.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
no changes since V2.
 arch/arm/boot/dts/imx6sx-sabreauto.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
index 812f40b..abe9054 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -161,6 +161,12 @@
 				MX6SX_PAD_KEY_COL1__GPIO2_IO_11		0x17059
 			>;
 		};
+
+		pinctrl_wdog: wdoggrp {
+			fsl,pins = <
+				MX6SX_PAD_GPIO1_IO13__WDOG1_WDOG_ANY 0x30b0
+			>;
+		};
 	};
 };
 
@@ -300,3 +306,9 @@
 		#gpio-cells = <2>;
 	};
 };
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
-- 
2.7.4