LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Abhishek Sahu <absahu@codeaurora.org>
To: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: David Woodhouse <dwmw2@infradead.org>,
	Brian Norris <computersforpeace@gmail.com>,
	Marek Vasut <marek.vasut@gmail.com>,
	Richard Weinberger <richard@nod.at>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-mtd@lists.infradead.org, Andy Gross <andy.gross@linaro.org>,
	Archit Taneja <architt@codeaurora.org>,
	Abhishek Sahu <absahu@codeaurora.org>
Subject: [PATCH v2 04/14] mtd: rawnand: qcom: use the ecc strength from device parameter
Date: Thu,  3 May 2018 17:50:31 +0530	[thread overview]
Message-ID: <1525350041-22995-5-git-send-email-absahu@codeaurora.org> (raw)
In-Reply-To: <1525350041-22995-1-git-send-email-absahu@codeaurora.org>

Currently the driver uses the ECC strength specified in DT.
The QPIC/EBI2 NAND supports 4 or 8-bit ECC correction. The same
kind of board can have different NAND parts so use the ECC
strength from device parameters if it is not specified in DT.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
---
* Changes from v1:

  1. Removed the custom logic and used the helper fuction.

 drivers/mtd/nand/raw/qcom_nandc.c | 31 ++++++++++++++++++++++---------
 1 file changed, 22 insertions(+), 9 deletions(-)

diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index b554fb6..a8d71ce 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -2315,13 +2315,21 @@ static int qcom_nand_ooblayout_free(struct mtd_info *mtd, int section,
 	.free = qcom_nand_ooblayout_free,
 };
 
+static int
+qcom_nandc_calc_ecc_bytes(int step_size, int strength)
+{
+	return strength == 4 ? 12 : 16;
+}
+NAND_ECC_CAPS_SINGLE(qcom_nandc_ecc_caps, qcom_nandc_calc_ecc_bytes,
+		     NANDC_STEP_SIZE, 4, 8);
+
 static int qcom_nand_host_setup(struct qcom_nand_host *host)
 {
 	struct nand_chip *chip = &host->chip;
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct nand_ecc_ctrl *ecc = &chip->ecc;
 	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
-	int cwperpage, bad_block_byte;
+	int cwperpage, bad_block_byte, ret;
 	bool wide_bus;
 	int ecc_mode = 1;
 
@@ -2334,8 +2342,20 @@ static int qcom_nand_host_setup(struct qcom_nand_host *host)
 		return -EINVAL;
 	}
 
+	cwperpage = mtd->writesize / ecc->size;
+
+	/*
+	 * Each CW has 4 available OOB bytes which will be protected with ECC
+	 * so remaining bytes can be used for ECC.
+	 */
+	ret = nand_ecc_param_setup(chip, &qcom_nandc_ecc_caps,
+				   mtd->oobsize - (cwperpage << 2));
+	if (ret) {
+		dev_err(nandc->dev, "No valid ecc settings possible\n");
+		return ret;
+	}
+
 	wide_bus = chip->options & NAND_BUSWIDTH_16 ? true : false;
-
 	if (ecc->strength >= 8) {
 		/* 8 bit ECC defaults to BCH ECC on all platforms */
 		host->bch_enabled = true;
@@ -2403,7 +2423,6 @@ static int qcom_nand_host_setup(struct qcom_nand_host *host)
 
 	mtd_set_ooblayout(mtd, &qcom_nand_ooblayout_ops);
 
-	cwperpage = mtd->writesize / ecc->size;
 	nandc->max_cwperpage = max_t(unsigned int, nandc->max_cwperpage,
 				     cwperpage);
 
@@ -2419,12 +2438,6 @@ static int qcom_nand_host_setup(struct qcom_nand_host *host)
 	 * for 8 bit ECC
 	 */
 	host->cw_size = host->cw_data + ecc->bytes;
-
-	if (ecc->bytes * (mtd->writesize / ecc->size) > mtd->oobsize) {
-		dev_err(nandc->dev, "ecc data doesn't fit in OOB area\n");
-		return -EINVAL;
-	}
-
 	bad_block_byte = mtd->writesize - host->cw_size * (cwperpage - 1) + 1;
 
 	host->cfg0 = (cwperpage - 1) << CW_PER_PAGE
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc.
is a member of Code Aurora Forum, hosted by The Linux Foundation

  parent reply	other threads:[~2018-05-03 12:21 UTC|newest]

Thread overview: 39+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-05-03 12:20 [PATCH v2 00/14] Update for QCOM NAND driver Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 01/14] mtd: rawnand: helper function for setting up ECC parameters Abhishek Sahu
2018-05-07  3:40   ` Masahiro Yamada
2018-05-07  6:01     ` Abhishek Sahu
2018-05-07  7:39     ` Boris Brezillon
2018-05-08  6:14       ` Masahiro Yamada
2018-05-08  7:21         ` Abhishek Sahu
2018-05-07  8:16   ` Boris Brezillon
2018-05-08  7:22     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 02/14] mtd: rawnand: denali: use helper function for ecc setup Abhishek Sahu
2018-05-21 14:30   ` Miquel Raynal
2018-05-22 14:09     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 03/14] dt-bindings: qcom_nandc: make nand-ecc-strength optional Abhishek Sahu
2018-05-07  8:40   ` Boris Brezillon
2018-05-21 14:32   ` Miquel Raynal
2018-05-22 14:08     ` Abhishek Sahu
2018-05-03 12:20 ` Abhishek Sahu [this message]
2018-05-07  8:28   ` [PATCH v2 04/14] mtd: rawnand: qcom: use the ecc strength from device parameter Boris Brezillon
2018-05-08  7:26     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 05/14] mtd: rawnand: qcom: wait for desc completion in all BAM channels Abhishek Sahu
2018-05-22  6:47   ` Miquel Raynal
2018-05-22 14:07     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 06/14] mtd: rawnand: qcom: erased page detection for uncorrectable errors only Abhishek Sahu
2018-05-22  7:04   ` Miquel Raynal
2018-05-22 14:10     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 07/14] mtd: rawnand: qcom: fix null pointer access for erased page detection Abhishek Sahu
2018-05-22  7:16   ` Miquel Raynal
2018-05-22 14:11     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 08/14] mtd: rawnand: qcom: parse read errors for read oob also Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 09/14] mtd: rawnand: qcom: modify write_oob to remove read codeword part Abhishek Sahu
2018-05-22 10:02   ` Miquel Raynal
2018-05-22 14:14     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 10/14] mtd: rawnand: qcom: fix return value for raw page read Abhishek Sahu
2018-05-22 12:04   ` Miquel Raynal
2018-05-22 14:15     ` Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 11/14] mtd: rawnand: qcom: minor code reorganization for bad block check Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 12/14] mtd: rawnand: qcom: check for operation errors in case of raw read Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 13/14] mtd: rawnand: qcom: helper function for " Abhishek Sahu
2018-05-03 12:20 ` [PATCH v2 14/14] mtd: rawnand: qcom: erased page bitflips detection Abhishek Sahu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1525350041-22995-5-git-send-email-absahu@codeaurora.org \
    --to=absahu@codeaurora.org \
    --cc=andy.gross@linaro.org \
    --cc=architt@codeaurora.org \
    --cc=boris.brezillon@bootlin.com \
    --cc=computersforpeace@gmail.com \
    --cc=dwmw2@infradead.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=marek.vasut@gmail.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=richard@nod.at \
    --subject='Re: [PATCH v2 04/14] mtd: rawnand: qcom: use the ecc strength from device parameter' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).