LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* [PATCH v2] ARM: dts: am437x-sk-evm: add wilink8 support
@ 2018-05-06  7:58 Eyal Reizer
  2018-05-15 18:32 ` Tony Lindgren
  0 siblings, 1 reply; 2+ messages in thread
From: Eyal Reizer @ 2018-05-06  7:58 UTC (permalink / raw)
  To: bcousson, tony, robh+dt, mark.rutland, linux-omap, devicetree,
	linux-kernel, nsekhar
  Cc: Eyal Reizer

enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control

Signed-off-by: Eyal Reizer <eyalr@ti.com>
---
Changes since V1:
 - Fix wlcore node number to @2
 - Capialaize ARM in subject line.

 arch/arm/boot/dts/am437x-sk-evm.dts | 115 ++++++++++++++++++++++++++++++++++++
 1 file changed, 115 insertions(+)

diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts
index 16d9db0..afffdb1 100644
--- a/arch/arm/boot/dts/am437x-sk-evm.dts
+++ b/arch/arm/boot/dts/am437x-sk-evm.dts
@@ -15,6 +15,7 @@
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "TI AM437x SK EVM";
@@ -158,6 +159,22 @@
 			};
 		};
 	};
+
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		/*
+		 * WL_EN is not SDIO standard compliant. It is an out of band
+		 * signal and hard to be dealt with in a standard way by the
+		 * SDIO core driver.
+		 * So modelling the WL_EN line as a regulator was a natural
+		 * choice as the MMC core already deals with MMC supplies.
+		 */
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &am43xx_pinmux {
@@ -424,6 +441,62 @@
 			AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
 		>;
 	};
+
+	mmc3_pins_default: pinmux_mmc3_pins_default {
+		pinctrl-single,pins = <
+			AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD21) cam1_data2.mmc2_clk */
+			AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE22) cam1_data3.mmc2_cmd */
+			AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD22) cam1_data4.mmc2_dat0 */
+			AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE23) cam1_data5.mmc2_dat1 */
+			AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD23) cam1_data6.mmc2_dat2 */
+			AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE24) cam1_data7.mmc2_dat3 */
+		>;
+	};
+
+	mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+		pinctrl-single,pins = <
+			AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD21) cam1_data2.mmc2_clk */
+			AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE22) cam1_data3.mmc2_cmd */
+			AM4372_IOPAD(0x9f8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD22) cam1_data4.mmc2_dat0 */
+			AM4372_IOPAD(0x9fc, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE23) cam1_data5.mmc2_dat1 */
+			AM4372_IOPAD(0xa00, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD23) cam1_data6.mmc2_dat2 */
+			AM4372_IOPAD(0xa04, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE24) cam1_data7.mmc2_dat3 */
+		>;
+	};
+
+	wlan_pins_default: pinmux_wlan_pins_default {
+		pinctrl-single,pins = <
+			AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* cam1_data8.gpio4_8 WL_EN */
+			AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* cam1_wen.gpio4_13 WL_IRQ */
+		>;
+	};
+
+	wlan_pins_sleep: pinmux_wlan_pins_sleep {
+		pinctrl-single,pins = <
+			AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* cam1_data8.gpio4_8 WL_EN */
+			AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* cam1_wen.gpio4_13 WL_IRQ */
+		>;
+	};
+
+	uart1_bt_pins_default: pinmux_uart1_bt_pins_default {
+		pinctrl-single,pins = <
+			AM4372_IOPAD(0x980, PIN_INPUT | MUX_MODE0)		/* uart1_rxd.uart1_rxd */
+			AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
+			AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_ctsn.uart1_ctsn */
+			AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
+			AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* cam1_data9.gpio4_7 BT_EN */
+		>;
+	};
+
+	uart1_bt_pins_sleep: pinmux_uart1_bt_pins_sleep {
+		pinctrl-single,pins = <
+			AM4372_IOPAD(0x980, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart1_rxd.uart1_rxd */
+			AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart1_txd.uart1_txd */
+			AM4372_IOPAD(0x978, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart1_ctsn.uart1_ctsn */
+			AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart1_rtsn.uart1_rtsn */
+			AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* cam1_data9.gpio4_7 BT_EN */
+		>;
+	};
 };
 
 &i2c0 {
@@ -606,6 +679,10 @@
 	status = "okay";
 };
 
+&gpio4 {
+	status = "okay";
+};
+
 &gpio5 {
 	status = "okay";
 };
@@ -620,6 +697,44 @@
 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 };
 
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&uart1_bt_pins_default>;
+	pinctrl-1 = <&uart1_bt_pins_sleep>;
+};
+
+&mmc3 {
+	status = "okay";
+	/*
+	 * these are on the crossbar and are outlined in the
+	 * xbar-event-map element
+	 */
+	dmas = <&edma_xbar 30 0 1>,
+		<&edma_xbar 31 0 2>;
+	dma-names = "tx", "rx";
+	vmmc-supply = <&vmmcwl_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mmc3_pins_default>;
+	pinctrl-1 = <&mmc3_pins_sleep>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,non-removable;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&wlan_pins_default>;
+		pinctrl-1 = <&wlan_pins_sleep>;
+		reg = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
 &usb2_phy1 {
 	status = "okay";
 };
-- 
2.7.4

^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: [PATCH v2] ARM: dts: am437x-sk-evm: add wilink8 support
  2018-05-06  7:58 [PATCH v2] ARM: dts: am437x-sk-evm: add wilink8 support Eyal Reizer
@ 2018-05-15 18:32 ` Tony Lindgren
  0 siblings, 0 replies; 2+ messages in thread
From: Tony Lindgren @ 2018-05-15 18:32 UTC (permalink / raw)
  To: Eyal Reizer
  Cc: bcousson, robh+dt, mark.rutland, linux-omap, devicetree,
	linux-kernel, nsekhar, Eyal Reizer

* Eyal Reizer <eyalreizer@gmail.com> [180506 01:00]:
> enable mmc3 used for wlan and uart1 used for bluetooth
> configure the gpios used for wlan and bluetooth controls
> add fixed voltage regulator used for wlan power control

Applying into omap-for-v4.18/dt thanks.

Tony

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2018-05-15 18:32 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-05-06  7:58 [PATCH v2] ARM: dts: am437x-sk-evm: add wilink8 support Eyal Reizer
2018-05-15 18:32 ` Tony Lindgren

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).