LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Ben Levinsky <ben.levinsky@xilinx.com>
To: ohad@wizery.com, bjorn.andersson@linaro.org,
	michal.simek@xilinx.com, jollys@xilinx.com,
	rajan.vaja@xilinx.com, robh+dt@kernel.org, mark.rutland@arm.com
Cc: linux-remoteproc@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, Jason Wu <j.wu@xilinx.com>,
	Wendy Liang <wendy.liang@xilinx.com>,
	Ed Mooring <ed.mooring@xilinx.com>
Subject: [PATCH 5/5] remoteproc: Add initial zynqmp R5 remoteproc driver
Date: Mon, 24 Feb 2020 09:52:31 -0800	[thread overview]
Message-ID: <1582566751-13118-6-git-send-email-ben.levinsky@xilinx.com> (raw)
In-Reply-To: <1582566751-13118-1-git-send-email-ben.levinsky@xilinx.com>

From: Jason Wu <j.wu@xilinx.com>

R5 is included in Xilinx Zynq UltraScale MPSoC so by adding this
remotproc driver, we can boot the R5 sub-system in different
configurations.

Signed-off-by: Jason Wu <j.wu@xilinx.com>

Acked-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Acked-by: Ben Levinsky <ben.levinsky@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Ben Levinsky <ben.levinsky@xilinx.com>
Signed-off-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ed Mooring <ed.mooring@xilinx.com>
Tested-by: Ben Levinsky <ben.levinsky@xilinx.com>
---
 drivers/remoteproc/Kconfig                |  10 +
 drivers/remoteproc/Makefile               |   1 +
 drivers/remoteproc/zynqmp_r5_remoteproc.c | 913 ++++++++++++++++++++++++++++++
 3 files changed, 924 insertions(+)
 create mode 100644 drivers/remoteproc/zynqmp_r5_remoteproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index de3862c..be14eba 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -206,6 +206,16 @@ config ST_REMOTEPROC
 	  processor framework.
 	  This can be either built-in or a loadable module.
 
+config ZYNQMP_R5_REMOTEPROC
+	tristate "ZynqMP_r5 remoteproc support"
+	depends on ARM64 && PM && ARCH_ZYNQMP
+	select RPMSG_VIRTIO
+	select MAILBOX
+	select ZYNQMP_IPI_MBOX
+	help
+	  Say y here to support ZynqMP R5 remote processors via the remote
+	  processor framework.
+
 config ST_SLIM_REMOTEPROC
 	tristate
 
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index e30a1b1..ee18d26 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -26,5 +26,6 @@ obj-$(CONFIG_QCOM_WCNSS_PIL)		+= qcom_wcnss_pil.o
 qcom_wcnss_pil-y			+= qcom_wcnss.o
 qcom_wcnss_pil-y			+= qcom_wcnss_iris.o
 obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
+obj-$(CONFIG_ZYNQMP_R5_REMOTEPROC)	+= zynqmp_r5_remoteproc.o
 obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
 obj-$(CONFIG_STM32_RPROC)		+= stm32_rproc.o
diff --git a/drivers/remoteproc/zynqmp_r5_remoteproc.c b/drivers/remoteproc/zynqmp_r5_remoteproc.c
new file mode 100644
index 0000000..a84ee8e
--- /dev/null
+++ b/drivers/remoteproc/zynqmp_r5_remoteproc.c
@@ -0,0 +1,913 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Zynq R5 Remote Processor driver
+ *
+ * Copyright (C) 2015 - 2018 Xilinx Inc.
+ * Copyright (C) 2015 Jason Wu <j.wu@xilinx.com>
+ *
+ * Based on origin OMAP and Zynq Remote Processor driver
+ *
+ * Copyright (C) 2012 Michal Simek <monstr@monstr.eu>
+ * Copyright (C) 2012 PetaLogix
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Copyright (C) 2011 Google, Inc.
+ */
+
+#include <linux/atomic.h>
+#include <linux/cpu.h>
+#include <linux/dma-mapping.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/genalloc.h>
+#include <linux/idr.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/mailbox_client.h>
+#include <linux/mailbox/zynqmp-ipi-message.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/pfn.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
+#include <linux/sysfs.h>
+
+#include "remoteproc_internal.h"
+
+#define MAX_RPROCS	2 /* Support up to 2 RPU */
+#define MAX_MEM_PNODES	4 /* Max power nodes for one RPU memory instance */
+
+/* PM proc states */
+#define PM_PROC_STATE_ACTIVE 1U
+
+/* IPI buffer MAX length */
+#define IPI_BUF_LEN_MAX	32U
+/* RX mailbox client buffer max length */
+#define RX_MBOX_CLIENT_BUF_MAX	(IPI_BUF_LEN_MAX + \
+				 sizeof(struct zynqmp_ipi_message))
+
+#define PM_HIVEC_MASK 0xF0000000
+
+#define TCM_BASE_ADDR  0xFFE00000
+#define TCM_LOW_BITMASK 0x000FFFFF
+#define TCM_BANK1_BITMASK 0x80000
+#define TCM_BANK1_HIGHBIT_BITMASK 0x90000
+
+static bool autoboot __read_mostly;
+
+static const struct zynqmp_eemi_ops *eemi_ops;
+
+/**
+ * struct zynqmp_r5_mem - zynqmp rpu memory data
+ * @pnode_id: TCM power domain ids
+ * @res: memory resource
+ * @node: list node
+ */
+struct zynqmp_r5_mem {
+	u32 pnode_id[MAX_MEM_PNODES];
+	struct resource res;
+	struct list_head node;
+};
+
+/**
+ * struct zynqmp_r5_pdata - zynqmp rpu remote processor private data
+ * @dev: device of RPU instance
+ * @rproc: rproc handle
+ * @parent: RPU slot platform data
+ * @pnode_id: RPU CPU power domain id
+ * @mems: memory resources
+ * @is_r5_mode_set: indicate if r5 operation mode is set
+ * @tx_mc: tx mailbox client
+ * @rx_mc: rx mailbox client
+ * @tx_chan: tx mailbox channel
+ * @rx_chan: rx mailbox channel
+ * @workqueue: workqueue for the RPU remoteproc
+ * @tx_mc_skbs: socket buffers for tx mailbox client
+ * @rx_mc_buf: rx mailbox client buffer to save the rx message
+ */
+struct zynqmp_r5_pdata {
+	struct device dev;
+	struct rproc *rproc;
+	struct zynqmp_rpu_domain_pdata *parent;
+	u32 pnode_id;
+	struct list_head mems;
+	bool is_r5_mode_set;
+	struct mbox_client tx_mc;
+	struct mbox_client rx_mc;
+	struct mbox_chan *tx_chan;
+	struct mbox_chan *rx_chan;
+	struct work_struct workqueue;
+	struct sk_buff_head tx_mc_skbs;
+	unsigned char rx_mc_buf[RX_MBOX_CLIENT_BUF_MAX];
+};
+
+/**
+ * struct zynqmp_rpu_domain_pdata - zynqmp rpu platform data
+ * @rpus: table of RPUs
+ * @rpu_mode: RPU core configuration
+ */
+struct zynqmp_rpu_domain_pdata {
+	struct zynqmp_r5_pdata rpus[MAX_RPROCS];
+	enum rpu_oper_mode rpu_mode;
+};
+
+/*
+ * r5_set_mode - set RPU operation mode
+ * @pdata: Remote processor private data
+ *
+ * set RPU operation mode
+ *
+ * Return: 0 for success, negative value for failure
+ */
+static int r5_set_mode(struct zynqmp_r5_pdata *pdata)
+{
+	u32 val[PAYLOAD_ARG_CNT] = {0}, expect;
+	struct zynqmp_rpu_domain_pdata *parent;
+	struct device *dev = &pdata->dev;
+	int ret;
+
+	if (pdata->is_r5_mode_set)
+		return 0;
+	parent = pdata->parent;
+	expect = (u32)parent->rpu_mode;
+	ret = eemi_ops->ioctl(pdata->pnode_id, IOCTL_GET_RPU_OPER_MODE,
+			  0, 0, val);
+	if (ret < 0) {
+		dev_err(dev, "failed to get RPU oper mode.\n");
+		return ret;
+	}
+	if (val[0] == expect) {
+		dev_dbg(dev, "RPU mode matches: %x\n", val[0]);
+	} else {
+		ret = eemi_ops->ioctl(pdata->pnode_id,
+				  IOCTL_SET_RPU_OPER_MODE,
+				  expect, 0, val);
+		if (ret < 0) {
+			dev_err(dev,
+				"failed to set RPU oper mode.\n");
+			return ret;
+		}
+	}
+	if (expect == (u32)PM_RPU_MODE_LOCKSTEP)
+		expect = (u32)PM_RPU_TCM_COMB;
+	else
+		expect = (u32)PM_RPU_TCM_SPLIT;
+	ret = eemi_ops->ioctl(pdata->pnode_id, IOCTL_TCM_COMB_CONFIG,
+			  expect, 0, val);
+	if (ret < 0) {
+		dev_err(dev, "failed to config TCM to %x.\n",
+			expect);
+		return ret;
+	}
+	pdata->is_r5_mode_set = true;
+	return 0;
+}
+
+/**
+ * r5_is_running - check if r5 is running
+ * @pdata: Remote processor private data
+ *
+ * check if R5 is running
+ *
+ * Return: true if r5 is running, false otherwise
+ */
+static bool r5_is_running(struct zynqmp_r5_pdata *pdata)
+{
+	u32 status, requirements, usage;
+	struct device *dev = &pdata->dev;
+
+	if (eemi_ops->get_node_status(pdata->pnode_id,
+				      &status, &requirements, &usage)) {
+		dev_err(dev, "Failed to get RPU node %d status.\n",
+			pdata->pnode_id);
+		return false;
+	} else if (status != PM_PROC_STATE_ACTIVE) {
+		dev_dbg(dev, "RPU is not running.\n");
+		return false;
+	}
+
+	dev_dbg(dev, "RPU is running.\n");
+	return true;
+}
+
+/*
+ * ZynqMP R5 remoteproc memory release function
+ */
+static int zynqmp_r5_mem_release(struct rproc *rproc,
+				 struct rproc_mem_entry *mem)
+{
+	struct zynqmp_r5_mem *priv;
+	int i, ret;
+	struct device *dev = &rproc->dev;
+
+	priv = mem->priv;
+	if (!priv)
+		return 0;
+	for (i = 0; i < MAX_MEM_PNODES; i++) {
+		if (priv->pnode_id[i]) {
+			dev_dbg(dev, "%s, pnode %d\n",
+				__func__, priv->pnode_id[i]);
+			ret = eemi_ops->release_node(priv->pnode_id[i]);
+			if (ret < 0) {
+				dev_err(dev,
+					"failed to release power node: %u\n",
+					priv->pnode_id[i]);
+				return ret;
+			}
+		} else {
+			break;
+		}
+	}
+	return 0;
+}
+
+/*
+ * ZynqMP R5 remoteproc operations
+ */
+static int zynqmp_r5_rproc_start(struct rproc *rproc)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_pdata *local = rproc->priv;
+	enum rpu_boot_mem bootmem;
+	int ret;
+
+	/* Set up R5 */
+	ret = r5_set_mode(local);
+	if (ret) {
+		dev_err(dev, "failed to set R5 operation mode.\n");
+		return ret;
+	}
+	if ((rproc->bootaddr & PM_HIVEC_MASK) == PM_HIVEC_MASK)
+		bootmem = PM_RPU_BOOTMEM_HIVEC;
+	else
+		bootmem = PM_RPU_BOOTMEM_LOVEC;
+	dev_info(dev, "RPU boot from %s.",
+		 bootmem == PM_RPU_BOOTMEM_HIVEC ? "OCM" : "TCM");
+
+	ret = eemi_ops->request_wakeup(local->pnode_id, 1, bootmem,
+				       ZYNQMP_PM_REQUEST_ACK_NO);
+	if (ret < 0) {
+		dev_err(dev, "failed to boot R5.\n");
+		return ret;
+	}
+	return 0;
+}
+
+static int zynqmp_r5_rproc_stop(struct rproc *rproc)
+{
+	struct zynqmp_r5_pdata *local = rproc->priv;
+	int ret;
+
+	ret = eemi_ops->force_powerdown(local->pnode_id,
+					ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+	if (ret < 0) {
+		dev_err(&local->dev, "failed to shutdown R5.\n");
+		return ret;
+	}
+	local->is_r5_mode_set = false;
+	return 0;
+}
+
+
+static int zynqmp_r5_parse_fw(struct rproc *rproc, const struct firmware *fw)
+{
+	struct zynqmp_r5_pdata *pdata = rproc->priv;
+	struct zynqmp_r5_mem *zynqmp_mem;
+	struct device *dev = &pdata->dev;
+	struct device_node *np = dev->of_node;
+	int num_mems;
+	int ret, i, dma_pool_index = 0;
+	struct reserved_mem *rmem;
+	struct rproc_mem_entry *mem;
+	struct device_node *child;
+	struct resource rsc;
+
+	num_mems = of_count_phandle_with_args(np, "memory-region", NULL);
+	if (num_mems <= 0)
+		return 0;
+	for (i = 0; i < num_mems; i++) {
+		struct device_node *node;
+		int ret;
+
+		node = of_parse_phandle(np, "memory-region", i);
+		rmem = of_reserved_mem_lookup(node);
+		if (!rmem) {
+			dev_err(dev, "unable to acquire memory-region\n");
+			return -EINVAL;
+		}
+		if (strstr(node->name, "vdev") &&
+			strstr(node->name, "buffer")) {
+			int id;
+			char name[16];
+
+			id = node->name[8] - 48;
+			snprintf(name, sizeof(name), "vdev%dbuffer", id);
+			/* Register DMA region */
+			mem = rproc_mem_entry_init(dev, NULL,
+						   (dma_addr_t)rmem->base,
+						   rmem->size, rmem->base,
+						   NULL, NULL,
+						   name);
+			if (!mem) {
+				dev_err(dev, "unable to initialize memory-region %s\n",
+						name);
+				return -EINVAL;
+			}
+
+			rproc_add_carveout(rproc, mem);
+			continue;
+		} else {
+			mem = rproc_of_resm_mem_entry_init(dev, i,
+							rmem->size,
+							rmem->base,
+							node->name);
+			if (!mem) {
+				dev_err(dev, "unable to initialize memory-region %s\n",
+						node->name);
+				return -EINVAL;
+			}
+
+			mem->va = devm_ioremap_wc(dev, rmem->base, rmem->size);
+			if (!mem->va) {
+				dev_err(dev, "unable to map va for %s\n",
+						node->name);
+				return -EINVAL;
+			}
+
+			rproc_add_carveout(rproc, mem);
+		}
+		if (!mem)
+			return -ENOMEM;
+
+
+		/*
+		 * It is non-DMA memory, used for firmware loading.
+		 * It will be added to the R5 remoteproc mappings later.
+		 */
+		zynqmp_mem = devm_kzalloc(dev, sizeof(*zynqmp_mem), GFP_KERNEL);
+		if (!zynqmp_mem)
+			return -ENOMEM;
+		ret = of_address_to_resource(node, 0, &zynqmp_mem->res);
+		if (ret) {
+			dev_err(dev, "unable to resolve memory region.\n");
+			return ret;
+		}
+		list_add_tail(&zynqmp_mem->node, &pdata->mems);
+		dev_dbg(dev, "%s, non-dma mem %s\n",
+			__func__, of_node_full_name(node));
+	}
+
+	/* map TCM memories */
+	for_each_available_child_of_node(np, child) {
+		ret = of_address_to_resource(child, 0, &rsc);
+		struct property *prop;
+		const __be32 *cur;
+		u32 pnode_id;
+		void *va;
+		dma_addr_t dma;
+		resource_size_t size;
+
+		i = 0;
+		of_property_for_each_u32(child, "pnode-id", prop, cur,
+								pnode_id) {
+			ret = eemi_ops->request_node(pnode_id,
+						ZYNQMP_PM_CAPABILITY_ACCESS, 0,
+						ZYNQMP_PM_REQUEST_ACK_BLOCKING);
+			if (ret < 0) {
+				dev_err(dev, "failed to request power node: %u\n",
+						pnode_id);
+				return ret;
+			}
+			ret = r5_set_mode(pdata);
+			if (ret < 0) {
+				dev_err(dev, "failed to set R5 operation mode.\n");
+				return ret;
+			}
+		}
+		size = resource_size(&rsc);
+
+		va = devm_ioremap_wc(dev, rsc.start, size);
+		if (!va) {
+			dev_err(dev, "unable to map va for TCM\n");
+			return -EINVAL;
+		}
+
+		/* zero out tcm base address */
+		if (rsc.start & TCM_BASE_ADDR) {
+			rsc.start &= TCM_LOW_BITMASK; /*wipe low bits */
+		/* handle tcm banks 1 a and b (0xffe9000 and oxffeb0000) */
+				if (rsc.start & TCM_BANK1_BITMASK)
+	/* wipe high bits as RPU only sees relative addr from 0x0 to 0x20000 */
+					rsc.start -= TCM_BANK1_HIGHBIT_BITMASK;
+		}
+
+		dma = (dma_addr_t)rsc.start;
+		mem = rproc_mem_entry_init(dev, va, dma, (int)size, rsc.start,
+						 NULL, zynqmp_r5_mem_release,
+						 rsc.name);
+		if (!mem)
+			return NULL;
+		rproc_add_carveout(rproc, mem);
+	}
+
+	ret = rproc_elf_load_rsc_table(rproc, fw);
+	if (ret == -EINVAL)
+		ret = 0;
+	return ret;
+}
+
+/* kick a firmware */
+static void zynqmp_r5_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct device *dev = rproc->dev.parent;
+	struct zynqmp_r5_pdata *local = rproc->priv;
+
+	dev_dbg(dev, "KICK Firmware to start send messages vqid %d\n", vqid);
+
+	if (vqid < 0) {
+		/* If vqid is negative, does not pass the vqid to
+		 * mailbox. As vqid is supposed to be 0 or possive.
+		 * It also gives a way to just kick instead but
+		 * not use the IPI buffer. It is better to provide
+		 * a proper way to pass the short message, which will
+		 * need to sync to upstream first, for now,
+		 * use negative vqid to assume no message will be
+		 * passed with IPI buffer, but just raise interrupt.
+		 * This will be faster as it doesn't need to copy the
+		 * message to the IPI buffer.
+		 *
+		 * It will ignore the return, as failure is due to
+		 * there already kicks in the mailbox queue.
+		 */
+		(void)mbox_send_message(local->tx_chan, NULL);
+	} else {
+		struct sk_buff *skb;
+		unsigned int skb_len;
+		struct zynqmp_ipi_message *mb_msg;
+		int ret;
+
+		skb_len = (unsigned int)(sizeof(vqid) + sizeof(mb_msg));
+		skb = alloc_skb(skb_len, GFP_ATOMIC);
+		if (!skb) {
+			dev_err(dev,
+				"Failed to allocate skb to kick remote.\n");
+			return;
+		}
+		mb_msg = (struct zynqmp_ipi_message *)skb_put(skb, skb_len);
+		mb_msg->len = sizeof(vqid);
+		memcpy(mb_msg->data, &vqid, sizeof(vqid));
+		skb_queue_tail(&local->tx_mc_skbs, skb);
+		ret = mbox_send_message(local->tx_chan, mb_msg);
+		if (ret < 0) {
+			dev_warn(dev, "Failed to kick remote.\n");
+			skb_dequeue_tail(&local->tx_mc_skbs);
+			kfree_skb(skb);
+		}
+	}
+}
+
+static struct rproc_ops zynqmp_r5_rproc_ops = {
+	.start		= zynqmp_r5_rproc_start,
+	.stop		= zynqmp_r5_rproc_stop,
+	.load		= rproc_elf_load_segments,
+	.parse_fw	= zynqmp_r5_parse_fw,
+	.find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
+	.sanity_check	= rproc_elf_sanity_check,
+	.get_boot_addr	= rproc_elf_get_boot_addr,
+	.kick		= zynqmp_r5_rproc_kick,
+};
+
+/* zynqmp_r5_mem_probe() - probes RPU TCM memory device
+ * @pdata: pointer to the RPU remoteproc private data
+ * @node: pointer to the memory node
+ *
+ * Function to retrieve memories resources for RPU TCM memory device.
+ */
+static int zynqmp_r5_mem_probe(struct zynqmp_r5_pdata *pdata,
+			       struct device_node *node)
+{
+	struct device *dev;
+	struct zynqmp_r5_mem *mem;
+	int ret;
+
+	dev = &pdata->dev;
+	mem = devm_kzalloc(dev, sizeof(*mem), GFP_KERNEL);
+	if (!mem)
+		return -ENOMEM;
+	ret = of_address_to_resource(node, 0, &mem->res);
+	if (ret < 0) {
+		dev_err(dev, "failed to get resource of memory %s",
+			of_node_full_name(node));
+		return -EINVAL;
+	}
+
+	/* Get the power domain id */
+	if (of_find_property(node, "pnode-id", NULL)) {
+		struct property *prop;
+		const __be32 *cur;
+		u32 val;
+		int i = 0;
+
+		of_property_for_each_u32(node, "pnode-id", prop, cur, val)
+			mem->pnode_id[i++] = val;
+	}
+	list_add_tail(&mem->node, &pdata->mems);
+	return 0;
+}
+
+/**
+ * zynqmp_r5_release() - ZynqMP R5 device release function
+ * @dev: pointer to the device struct of ZynqMP R5
+ *
+ * Function to release ZynqMP R5 device.
+ */
+static void zynqmp_r5_release(struct device *dev)
+{
+	struct zynqmp_r5_pdata *pdata;
+	struct rproc *rproc;
+	struct sk_buff *skb;
+
+	pdata = dev_get_drvdata(dev);
+	rproc = pdata->rproc;
+	if (rproc) {
+		rproc_del(rproc);
+		rproc_free(rproc);
+	}
+	if (pdata->tx_chan)
+		mbox_free_channel(pdata->tx_chan);
+	if (pdata->rx_chan)
+		mbox_free_channel(pdata->rx_chan);
+	/* Discard all SKBs */
+	while (!skb_queue_empty(&pdata->tx_mc_skbs)) {
+		skb = skb_dequeue(&pdata->tx_mc_skbs);
+		kfree_skb(skb);
+	}
+
+	put_device(dev->parent);
+}
+
+/**
+ * event_notified_idr_cb() - event notified idr callback
+ * @id: idr id
+ * @ptr: pointer to idr private data
+ * @data: data passed to idr_for_each callback
+ *
+ * Pass notification to remtoeproc virtio
+ *
+ * Return: 0. having return is to satisfy the idr_for_each() function
+ *          pointer input argument requirement.
+ **/
+static int event_notified_idr_cb(int id, void *ptr, void *data)
+{
+	struct rproc *rproc = data;
+
+	(void)rproc_vq_interrupt(rproc, id);
+	return 0;
+}
+
+/**
+ * handle_event_notified() - remoteproc notification work funciton
+ * @work: pointer to the work structure
+ *
+ * It checks each registered remoteproc notify IDs.
+ */
+static void handle_event_notified(struct work_struct *work)
+{
+	struct rproc *rproc;
+	struct zynqmp_r5_pdata *local;
+
+	local = container_of(work, struct zynqmp_r5_pdata, workqueue);
+
+	(void)mbox_send_message(local->rx_chan, NULL);
+	rproc = local->rproc;
+
+	/*
+	 * We only use IPI for interrupt. The firmware side may or may
+	 * not write the notifyid when it trigger IPI.
+	 * And thus, we scan through all the registered notifyids.
+	 */
+	idr_for_each(&rproc->notifyids, event_notified_idr_cb, rproc);
+}
+
+/**
+ * zynqmp_r5_mb_rx_cb() - Receive channel mailbox callback
+ * @cl: mailbox client
+ * @mssg: message pointer
+ *
+ * It will schedule the R5 notification work.
+ */
+static void zynqmp_r5_mb_rx_cb(struct mbox_client *cl, void *mssg)
+{
+	struct zynqmp_r5_pdata *local;
+
+	local = container_of(cl, struct zynqmp_r5_pdata, rx_mc);
+	if (mssg) {
+		struct zynqmp_ipi_message *ipi_msg, *buf_msg;
+		size_t len;
+
+		ipi_msg = (struct zynqmp_ipi_message *)mssg;
+		buf_msg = (struct zynqmp_ipi_message *)local->rx_mc_buf;
+		len = (ipi_msg->len >= IPI_BUF_LEN_MAX) ?
+		      IPI_BUF_LEN_MAX : ipi_msg->len;
+		buf_msg->len = len;
+		memcpy(buf_msg->data, ipi_msg->data, len);
+	}
+	schedule_work(&local->workqueue);
+}
+
+/**
+ * zynqmp_r5_mb_tx_done() - Request has been sent to the remote
+ * @cl: mailbox client
+ * @mssg: pointer to the message which has been sent
+ * @r: status of last TX - OK or error
+ *
+ * It will be called by the mailbox framework when the last TX has done.
+ */
+static void zynqmp_r5_mb_tx_done(struct mbox_client *cl, void *mssg, int r)
+{
+	struct zynqmp_r5_pdata *local;
+	struct sk_buff *skb;
+
+	if (!mssg)
+		return;
+	local = container_of(cl, struct zynqmp_r5_pdata, tx_mc);
+	skb = skb_dequeue(&local->tx_mc_skbs);
+	kfree_skb(skb);
+}
+
+/**
+ * zynqmp_r5_setup_mbox() - Setup mailboxes
+ *
+ * @pdata: pointer to the ZynqMP R5 processor platform data
+ * @node: pointer of the device node
+ *
+ * Function to setup mailboxes to talk to RPU.
+ *
+ * Return: 0 for success, negative value for failure.
+ */
+static int zynqmp_r5_setup_mbox(struct zynqmp_r5_pdata *pdata)
+{
+	struct device *dev = &pdata->dev;
+	struct mbox_client *mclient;
+
+	/* Setup TX mailbox channel client */
+	mclient = &pdata->tx_mc;
+	mclient->dev = dev;
+	mclient->rx_callback = NULL;
+	mclient->tx_block = false;
+	mclient->knows_txdone = false;
+	mclient->tx_done = zynqmp_r5_mb_tx_done;
+
+	/* Setup TX mailbox channel client */
+	mclient = &pdata->rx_mc;
+	mclient->dev = dev;
+	mclient->rx_callback = zynqmp_r5_mb_rx_cb;
+	mclient->tx_block = false;
+	mclient->knows_txdone = false;
+
+	INIT_WORK(&pdata->workqueue, handle_event_notified);
+
+	/* Request TX and RX channels */
+	pdata->tx_chan = mbox_request_channel_byname(&pdata->tx_mc, "tx");
+	if (IS_ERR(pdata->tx_chan)) {
+		dev_err(dev, "failed to request mbox tx channel.\n");
+		pdata->tx_chan = NULL;
+		return -EINVAL;
+	}
+	pdata->rx_chan = mbox_request_channel_byname(&pdata->rx_mc, "rx");
+	if (IS_ERR(pdata->rx_chan)) {
+		dev_err(dev, "failed to request mbox rx channel.\n");
+		pdata->rx_chan = NULL;
+		return -EINVAL;
+	}
+	skb_queue_head_init(&pdata->tx_mc_skbs);
+	return 0;
+}
+
+/**
+ * zynqmp_r5_probe() - Probes ZynqMP R5 processor device node
+ * @pdata: pointer to the ZynqMP R5 processor platform data
+ * @pdev: parent RPU domain platform device
+ * @node: pointer of the device node
+ *
+ * Function to retrieve the information of the ZynqMP R5 device node.
+ *
+ * Return: 0 for success, negative value for failure.
+ */
+static int zynqmp_r5_probe(struct zynqmp_r5_pdata *pdata,
+			   struct platform_device *pdev,
+			   struct device_node *node)
+{
+	struct device *dev = &pdata->dev;
+	struct rproc *rproc;
+	struct device_node *nc;
+	int ret;
+
+	/* Create device for ZynqMP R5 device */
+	dev->parent = &pdev->dev;
+	dev->release = zynqmp_r5_release;
+	dev->of_node = node;
+	dev_set_name(dev, "%s", of_node_full_name(node));
+	dev_set_drvdata(dev, pdata);
+	ret = device_register(dev);
+	if (ret) {
+		dev_err(dev, "failed to register device.\n");
+		return ret;
+	}
+	get_device(&pdev->dev);
+
+	/* Allocate remoteproc instance */
+	rproc = rproc_alloc(dev, dev_name(dev), &zynqmp_r5_rproc_ops, NULL, 0);
+	if (!rproc) {
+		dev_err(dev, "rproc allocation failed.\n");
+		ret = -ENOMEM;
+		goto error;
+	}
+	rproc->auto_boot = autoboot;
+	pdata->rproc = rproc;
+	rproc->priv = pdata;
+
+	/*
+	 * The device has not been spawned from a device tree, so
+	 * arch_setup_dma_ops has not been not called, thus leaving
+	 * the device with dummy DMA ops.
+	 * Fix this by inheriting the parent's DMA ops and mask.
+	 */
+	rproc->dev.dma_mask = pdev->dev.dma_mask;
+	set_dma_ops(&rproc->dev, get_dma_ops(&pdev->dev));
+
+	/* Probe R5 memory devices */
+	INIT_LIST_HEAD(&pdata->mems);
+	for_each_available_child_of_node(node, nc) {
+		ret = zynqmp_r5_mem_probe(pdata, nc);
+		if (ret) {
+			dev_err(dev, "failed to probe memory %s.\n",
+				of_node_full_name(nc));
+			goto error;
+		}
+	}
+
+	/* Set up DMA mask */
+	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_warn(dev, "dma_set_coherent_mask failed: %d\n", ret);
+		/* If DMA is not configured yet, try to configure it. */
+		ret = of_dma_configure(dev, node, true);
+		if (ret) {
+			dev_err(dev, "failed to configure DMA.\n");
+			goto error;
+		}
+	}
+
+	/* Get R5 power domain node */
+	ret = of_property_read_u32(node, "pnode-id", &pdata->pnode_id);
+	if (ret) {
+		dev_err(dev, "failed to get power node id.\n");
+		goto error;
+	}
+
+	/* Check if R5 is running */
+	if (r5_is_running(pdata)) {
+		atomic_inc(&rproc->power);
+		rproc->state = RPROC_RUNNING;
+	}
+
+	if (!of_get_property(dev->of_node, "mboxes", NULL)) {
+		dev_info(dev, "no mailboxes.\n");
+	} else {
+		ret = zynqmp_r5_setup_mbox(pdata);
+		if (ret < 0)
+			goto error;
+	}
+
+	/* Add R5 remoteproc */
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err(dev, "rproc registration failed\n");
+		goto error;
+	}
+
+	return 0;
+error:
+	if (pdata->rproc)
+		rproc_free(pdata->rproc);
+	pdata->rproc = NULL;
+	device_unregister(dev);
+	put_device(&pdev->dev);
+	return ret;
+}
+
+static int zynqmp_r5_remoteproc_probe(struct platform_device *pdev)
+{
+	const unsigned char *prop;
+	int ret = 0, i;
+	struct zynqmp_rpu_domain_pdata *local;
+	struct device *dev = &pdev->dev;
+	struct device_node *nc;
+
+	eemi_ops = zynqmp_pm_get_eemi_ops();
+	if (IS_ERR(eemi_ops))
+		return PTR_ERR(eemi_ops);
+
+	local = devm_kzalloc(dev, sizeof(*local), GFP_KERNEL);
+	if (!local)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, local);
+
+	prop = of_get_property(dev->of_node, "core_conf", NULL);
+	if (!prop) {
+		dev_err(&pdev->dev, "core_conf is not used.\n");
+		return -EINVAL;
+	}
+
+	dev_info(dev, "RPU core_conf: %s\n", prop);
+	if (!strcmp(prop, "split")) {
+		local->rpu_mode = PM_RPU_MODE_SPLIT;
+	} else if (!strcmp(prop, "lockstep")) {
+		local->rpu_mode = PM_RPU_MODE_LOCKSTEP;
+	} else {
+		dev_err(dev,
+			"Invalid core_conf mode provided - %s , %d\n",
+			prop, (int)local->rpu_mode);
+		return -EINVAL;
+	}
+
+	i = 0;
+	for_each_available_child_of_node(dev->of_node, nc) {
+		if (i > 1) {
+			dev_err(dev, "Max number allowed RPUs described is 2.\n");
+			return -EINVAL;
+		}
+		local->rpus[i].parent = local;
+		ret = zynqmp_r5_probe(&local->rpus[i], pdev, nc);
+		if (ret) {
+			dev_err(dev, "failed to probe rpu %s.\n",
+				of_node_full_name(nc));
+			return ret;
+		}
+		i++;
+	}
+
+	return 0;
+}
+
+static int zynqmp_r5_remoteproc_remove(struct platform_device *pdev)
+{
+	struct zynqmp_rpu_domain_pdata *local = platform_get_drvdata(pdev);
+	int i;
+
+	for (i = 0; i < MAX_RPROCS; i++) {
+		struct zynqmp_r5_pdata *rpu = &local->rpus[i];
+		struct rproc *rproc;
+
+		rproc = rpu->rproc;
+		if (rproc) {
+			rproc_del(rproc);
+			rproc_free(rproc);
+			rpu->rproc = NULL;
+		}
+		if (rpu->tx_chan) {
+			mbox_free_channel(rpu->tx_chan);
+			rpu->tx_chan = NULL;
+		}
+		if (rpu->rx_chan) {
+			mbox_free_channel(rpu->rx_chan);
+			rpu->rx_chan = NULL;
+		}
+
+		device_unregister(&rpu->dev);
+	}
+
+	return 0;
+}
+
+/* Match table for OF platform binding */
+static const struct of_device_id zynqmp_r5_remoteproc_match[] = {
+	{ .compatible = "xlnx,zynqmp-r5-remoteproc-1.0", },
+	{ /* end of list */ },
+};
+MODULE_DEVICE_TABLE(of, zynqmp_r5_remoteproc_match);
+
+static struct platform_driver zynqmp_r5_remoteproc_driver = {
+	.probe = zynqmp_r5_remoteproc_probe,
+	.remove = zynqmp_r5_remoteproc_remove,
+	.driver = {
+		.name = "zynqmp_r5_remoteproc",
+		.of_match_table = zynqmp_r5_remoteproc_match,
+	},
+};
+module_platform_driver(zynqmp_r5_remoteproc_driver);
+
+module_param_named(autoboot,  autoboot, bool, 0444);
+MODULE_PARM_DESC(autoboot,
+		 "enable | disable autoboot. (default: true)");
+
+MODULE_AUTHOR("Jason Wu <j.wu@xilinx.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("ZynqMP R5 remote processor control driver");
-- 
2.7.4


  parent reply	other threads:[~2020-02-24 17:52 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-24 17:52 [PATCH 0/5] remoteproc: Add zynqmp_r5 driver Ben Levinsky
2020-02-24 17:52 ` [PATCH 1/5] firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration Ben Levinsky
2020-03-12  7:32   ` Michal Simek
2020-02-24 17:52 ` [PATCH 2/5] firmware: xilinx: Add shutdown/wakeup APIs Ben Levinsky
2020-03-12  7:34   ` Michal Simek
2020-02-24 17:52 ` [PATCH 3/5] firmware: xilinx: Add zynqmp_get_node_status API Ben Levinsky
2020-03-11 16:26   ` Mathieu Poirier
2020-02-24 17:52 ` [PATCH 4/5] dt-bindings: remoteproc: Add documentation for ZynqMP R5 rproc bindings Ben Levinsky
2020-03-02 20:27   ` Rob Herring
2020-03-11 16:55   ` Mathieu Poirier
2020-02-24 17:52 ` Ben Levinsky [this message]
2020-03-05 23:12   ` [PATCH 5/5] remoteproc: Add initial zynqmp R5 remoteproc driver Michael Auchter
2020-03-11 17:38   ` Mathieu Poirier

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1582566751-13118-6-git-send-email-ben.levinsky@xilinx.com \
    --to=ben.levinsky@xilinx.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=ed.mooring@xilinx.com \
    --cc=j.wu@xilinx.com \
    --cc=jollys@xilinx.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-remoteproc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=michal.simek@xilinx.com \
    --cc=ohad@wizery.com \
    --cc=rajan.vaja@xilinx.com \
    --cc=robh+dt@kernel.org \
    --cc=wendy.liang@xilinx.com \
    --subject='Re: [PATCH 5/5] remoteproc: Add initial zynqmp R5 remoteproc driver' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).