LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* RFC: powerpc: remove GEMINI support?
@ 2006-11-24 23:49 Adrian Bunk
  2006-12-19  4:12 ` [2.6 patch] powerpc: remove the broken Gemini support Adrian Bunk
  0 siblings, 1 reply; 6+ messages in thread
From: Adrian Bunk @ 2006-11-24 23:49 UTC (permalink / raw)
  To: paulus, Kumar Gala; +Cc: linuxppc-dev, Roman Zippel, linux-kernel

I just saw the commit message below.

There seems to have been some although unmerged work on APUS support by 
Roman, but I didn't find any recent work on bringing the GEMINI support 
back into life.

Is this a wrong impression, or would a patch to remove it be OK?

cu
Adrian


commit e8be1c8e065691c332fd8e9bae70c7096a69c31d
Author: Kumar Gala <galak@freescale.com>
Date:   Sun Jul 31 22:34:51 2005 -0700

    [PATCH] ppc32: Mark boards that don't build as BROKEN
    
    Marked APUS and GEMINI as BROKEN since they do not build at the platform
    level.  We have requested that the maintainers of these boards/platforms
    fix them by the time 2.6.15 is released or we plan on concerning them
    unmaintained and thus removing them.
    
    Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
    Signed-off-by: Andrew Morton <akpm@osdl.org>
    Signed-off-by: Linus Torvalds <torvalds@osdl.org>

diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index 2c2da9b..f6db3b3 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -558,6 +558,7 @@ config PPC_MULTIPLATFORM
 
 config APUS
 	bool "Amiga-APUS"
+	depends on BROKEN
 	help
 	  Select APUS if configuring for a PowerUP Amiga.
 	  More information is available at:
@@ -647,6 +648,7 @@ config PAL4
 
 config GEMINI
 	bool "Synergy-Gemini"
+	depends on BROKEN
 	help
 	  Select Gemini if configuring for a Synergy Microsystems' Gemini
 	  series Single Board Computer.  More information is available at:


^ permalink raw reply	[flat|nested] 6+ messages in thread
* [2.6 patch] powerpc: remove the broken Gemini support
@ 2007-01-14  9:15 Adrian Bunk
  0 siblings, 0 replies; 6+ messages in thread
From: Adrian Bunk @ 2007-01-14  9:15 UTC (permalink / raw)
  To: paulus, Kumar Gala; +Cc: linuxppc-dev, linux-kernel

This patch removes the broken Gemini support.

Signed-off-by: Adrian Bunk <bunk@stusta.de>

---

 arch/powerpc/kernel/head_32.S              |    5 
 arch/powerpc/platforms/embedded6xx/Kconfig |    9 
 arch/ppc/Kconfig                           |    9 
 arch/ppc/boot/simple/Makefile              |    4 
 arch/ppc/boot/simple/misc.c                |   15 
 arch/ppc/configs/gemini_defconfig          |  619 ---------------------
 arch/ppc/kernel/head.S                     |   18 
 arch/ppc/platforms/Makefile                |    1 
 arch/ppc/platforms/gemini.h                |  165 -----
 arch/ppc/platforms/gemini_pci.c            |   41 -
 arch/ppc/platforms/gemini_prom.S           |   90 ---
 arch/ppc/platforms/gemini_serial.h         |   40 -
 arch/ppc/platforms/gemini_setup.c          |  577 -------------------
 arch/ppc/syslib/Makefile                   |    1 
 arch/ppc/xmon/start.c                      |    5 
 include/asm-ppc/m48t35.h                   |   77 --
 include/asm-ppc/serial.h                   |    2 
 17 files changed, 2 insertions(+), 1676 deletions(-)


--- linux-2.6.20-rc1-mm1/arch/powerpc/kernel/head_32.S.old	2006-12-19 03:57:49.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/powerpc/kernel/head_32.S	2006-12-19 03:58:30.000000000 +0100
@@ -344,12 +344,7 @@
 /* System reset */
 /* core99 pmac starts the seconary here by changing the vector, and
    putting it back to what it was (unknown_exception) when done.  */
-#if defined(CONFIG_GEMINI) && defined(CONFIG_SMP)
-	. = 0x100
-	b	__secondary_start_gemini
-#else
 	EXCEPTION(0x100, Reset, unknown_exception, EXC_XFER_STD)
-#endif
 
 /* Machine check */
 /*
--- linux-2.6.20-rc1-mm1/arch/powerpc/platforms/embedded6xx/Kconfig.old	2006-12-19 03:59:10.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/powerpc/platforms/embedded6xx/Kconfig	2006-12-19 03:59:26.000000000 +0100
@@ -104,15 +104,6 @@
 config PAL4
 	bool "SBS-Palomar4"
 
-config GEMINI
-	bool "Synergy-Gemini"
-	select PPC_INDIRECT_PCI
-	depends on BROKEN
-	help
-	  Select Gemini if configuring for a Synergy Microsystems' Gemini
-	  series Single Board Computer.  More information is available at:
-	  <http://www.synergymicro.com/PressRel/97_10_15.html>.
-
 config EST8260
 	bool "EST8260"
 	---help---
--- linux-2.6.20-rc1-mm1/arch/ppc/Kconfig.old	2006-12-19 03:59:37.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/Kconfig	2006-12-19 03:59:48.000000000 +0100
@@ -670,15 +670,6 @@
 config PAL4
 	bool "SBS-Palomar4"
 
-config GEMINI
-	bool "Synergy-Gemini"
-	depends on BROKEN
-	select PPC_INDIRECT_PCI
-	help
-	  Select Gemini if configuring for a Synergy Microsystems' Gemini
-	  series Single Board Computer.  More information is available at:
-	  <http://www.synergymicro.com/PressRel/97_10_15.html>.
-
 config EST8260
 	bool "EST8260"
 	---help---
--- linux-2.6.20-rc1-mm1/arch/ppc/boot/simple/Makefile.old	2006-12-19 03:59:58.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/boot/simple/Makefile	2006-12-19 04:00:20.000000000 +0100
@@ -116,10 +116,6 @@
      extra.o-$(CONFIG_CHESTNUT)		:= misc-chestnut.o
          end-$(CONFIG_CHESTNUT)		:= chestnut
 
-      zimage-$(CONFIG_GEMINI)		:= zImage-STRIPELF
-zimageinitrd-$(CONFIG_GEMINI)		:= zImage.initrd-STRIPELF
-         end-$(CONFIG_GEMINI)		:= gemini
-
      extra.o-$(CONFIG_KATANA)		:= misc-katana.o
          end-$(CONFIG_KATANA)		:= katana
    cacheflag-$(CONFIG_KATANA)		:= -include $(clear_L2_L3)
--- linux-2.6.20-rc1-mm1/arch/ppc/boot/simple/misc.c.old	2006-12-19 04:00:33.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/boot/simple/misc.c	2006-12-19 04:01:18.000000000 +0100
@@ -42,14 +42,11 @@
 #endif
 
 /* Will / Can the user give input?
- * Val Henson has requested that Gemini doesn't wait for the
- * user to edit the cmdline or not.
  */
 #if (defined(CONFIG_SERIAL_8250_CONSOLE) \
 	|| defined(CONFIG_VGA_CONSOLE) \
 	|| defined(CONFIG_SERIAL_MPC52xx_CONSOLE) \
-	|| defined(CONFIG_SERIAL_MPSC_CONSOLE)) \
-	&& !defined(CONFIG_GEMINI)
+	|| defined(CONFIG_SERIAL_MPSC_CONSOLE))
 #define INTERACTIVE_CONSOLE	1
 #endif
 
@@ -178,16 +175,6 @@
 
 	if (keyb_present)
 		CRT_tstc();  /* Forces keyboard to be initialized */
-#ifdef CONFIG_GEMINI
-	/*
-	 * If cmd_line is empty and cmd_preset is not, copy cmd_preset
-	 * to cmd_line.  This way we can override cmd_preset with the
-	 * command line from Smon.
-	 */
-
-	if ( (cmd_line[0] == '\0') && (cmd_preset[0] != '\0'))
-		memcpy (cmd_line, cmd_preset, sizeof(cmd_preset));
-#endif
 
 	/* Display standard Linux/PPC boot prompt for kernel args */
 	puts("\nLinux/PPC load: ");
--- linux-2.6.20-rc1-mm1/arch/ppc/kernel/head.S.old	2006-12-19 04:01:36.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/kernel/head.S	2006-12-19 04:01:56.000000000 +0100
@@ -310,12 +310,7 @@
 /* System reset */
 /* core99 pmac starts the seconary here by changing the vector, and
    putting it back to what it was (unknown_exception) when done.  */
-#if defined(CONFIG_GEMINI) && defined(CONFIG_SMP)
-	. = 0x100
-	b	__secondary_start_gemini
-#else
 	EXCEPTION(0x100, Reset, unknown_exception, EXC_XFER_STD)
-#endif
 
 /* Machine check */
 	. = 0x200
@@ -897,19 +892,6 @@
 #endif /* CONFIG_APUS */
 
 #ifdef CONFIG_SMP
-#ifdef CONFIG_GEMINI
-	.globl	__secondary_start_gemini
-__secondary_start_gemini:
-        mfspr   r4,SPRN_HID0
-        ori     r4,r4,HID0_ICFI
-        li      r3,0
-        ori     r3,r3,HID0_ICE
-        andc    r4,r4,r3
-        mtspr   SPRN_HID0,r4
-        sync
-        b       __secondary_start
-#endif /* CONFIG_GEMINI */
-
 	.globl	__secondary_start_pmac_0
 __secondary_start_pmac_0:
 	/* NB the entries for cpus 0, 1, 2 must each occupy 8 bytes. */
--- linux-2.6.20-rc1-mm1/arch/ppc/platforms/Makefile.old	2006-12-19 04:02:16.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/platforms/Makefile	2006-12-19 04:02:25.000000000 +0100
@@ -13,7 +13,6 @@
 obj-$(CONFIG_CPCI690)		+= cpci690.o
 obj-$(CONFIG_EV64260)		+= ev64260.o
 obj-$(CONFIG_CHESTNUT)		+= chestnut.o
-obj-$(CONFIG_GEMINI)		+= gemini_pci.o gemini_setup.o gemini_prom.o
 obj-$(CONFIG_LOPEC)		+= lopec.o
 obj-$(CONFIG_KATANA)		+= katana.o
 obj-$(CONFIG_HDPU)		+= hdpu.o
--- linux-2.6.20-rc1-mm1/arch/ppc/syslib/Makefile.old	2006-12-19 04:05:24.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/syslib/Makefile	2006-12-19 04:05:37.000000000 +0100
@@ -45,7 +45,6 @@
 obj-$(CONFIG_EV64260)		+= todc_time.o pci_auto.o
 obj-$(CONFIG_EV64360)		+= todc_time.o
 obj-$(CONFIG_CHESTNUT)		+= mv64360_pic.o pci_auto.o
-obj-$(CONFIG_GEMINI)		+= open_pic.o
 obj-$(CONFIG_GT64260)		+= gt64260_pic.o
 obj-$(CONFIG_LOPEC)		+= pci_auto.o todc_time.o
 obj-$(CONFIG_HDPU)		+= pci_auto.o
--- linux-2.6.20-rc1-mm1/arch/ppc/xmon/start.c.old	2006-12-19 04:05:49.000000000 +0100
+++ linux-2.6.20-rc1-mm1/arch/ppc/xmon/start.c	2006-12-19 04:05:59.000000000 +0100
@@ -58,10 +58,7 @@
 void
 xmon_map_scc(void)
 {
-#if defined(CONFIG_GEMINI)
-	/* should already be mapped by the kernel boot */
-	sccd = (volatile unsigned char *) 0xffeffb08;
-#elif defined(CONFIG_405GP)
+#if defined(CONFIG_405GP)
 	sccd = (volatile unsigned char *)0xef600300;
 #elif defined(CONFIG_440EP)
 	sccd = (volatile unsigned char *) ioremap(PPC440EP_UART0_ADDR, 8);
--- linux-2.6.20-rc1-mm1/include/asm-ppc/serial.h.old	2006-12-19 04:06:20.000000000 +0100
+++ linux-2.6.20-rc1-mm1/include/asm-ppc/serial.h	2006-12-19 04:06:28.000000000 +0100
@@ -11,8 +11,6 @@
 #include <platforms/ev64260.h>
 #elif defined(CONFIG_CHESTNUT)
 #include <platforms/chestnut.h>
-#elif defined(CONFIG_GEMINI)
-#include <platforms/gemini_serial.h>
 #elif defined(CONFIG_POWERPMC250)
 #include <platforms/powerpmc250.h>
 #elif defined(CONFIG_LOPEC)
--- linux-2.6.20-rc1-mm1/arch/ppc/platforms/gemini.h	2006-11-29 22:57:37.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,165 +0,0 @@
-/*
- *  Onboard registers and descriptions for Synergy Microsystems'
- *  "Gemini" boards.
- *
- */
-#ifdef __KERNEL__
-#ifndef __PPC_GEMINI_H
-#define __PPC_GEMINI_H
-
-/*  Registers  */
-
-#define GEMINI_SERIAL_B     (0xffeffb00)
-#define GEMINI_SERIAL_A     (0xffeffb08)
-#define GEMINI_USWITCH      (0xffeffd00)
-#define GEMINI_BREV         (0xffeffe00)
-#define GEMINI_BECO         (0xffeffe08)
-#define GEMINI_FEAT         (0xffeffe10)
-#define GEMINI_BSTAT        (0xffeffe18)
-#define GEMINI_CPUSTAT      (0xffeffe20)
-#define GEMINI_L2CFG        (0xffeffe30)
-#define GEMINI_MEMCFG       (0xffeffe38)
-#define GEMINI_FLROM        (0xffeffe40)
-#define GEMINI_P0PCI        (0xffeffe48)
-#define GEMINI_FLWIN        (0xffeffe50)
-#define GEMINI_P0INTMASK    (0xffeffe60)
-#define GEMINI_P0INTAP      (0xffeffe68)
-#define GEMINI_PCIERR       (0xffeffe70)
-#define GEMINI_LEDBASE      (0xffeffe80)
-#define GEMINI_RTC          (0xffe9fff8)
-#define GEMINI_LEDS         8
-#define GEMINI_SWITCHES     8
-
-
-/* Flash ROM bit definitions */
-#define GEMINI_FLS_WEN      (1<<0)
-#define GEMINI_FLS_JMP      (1<<6)
-#define GEMINI_FLS_BOOT     (1<<7)
-
-/* Memory bit definitions */
-#define GEMINI_MEM_TYPE_MASK 0xc0
-#define GEMINI_MEM_SIZE_MASK 0x38
-#define GEMINI_MEM_BANK_MASK 0x07
-
-/* L2 cache bit definitions */
-#define GEMINI_L2_SIZE_MASK  0xc0
-#define GEMINI_L2_RATIO_MASK 0x03
-
-/* Timebase register bit definitons */
-#define GEMINI_TIMEB0_EN     (1<<0)
-#define GEMINI_TIMEB1_EN     (1<<1)
-#define GEMINI_TIMEB2_EN     (1<<2)
-#define GEMINI_TIMEB3_EN     (1<<3)
-
-/* CPU status bit definitions */
-#define GEMINI_CPU_ID_MASK   0x03
-#define GEMINI_CPU_COUNT_MASK 0x0c
-#define GEMINI_CPU0_HALTED   (1<<4)
-#define GEMINI_CPU1_HALTED   (1<<5)
-#define GEMINI_CPU2_HALTED   (1<<6)
-#define GEMINI_CPU3_HALTED   (1<<7)
-
-/* Board status bit definitions */
-#define GEMINI_BRD_FAIL      (1<<0)   /* FAIL led is lit */
-#define GEMINI_BRD_BUS_MASK  0x0c     /* PowerPC bus speed */
-
-/* Board family/feature bit descriptions */
-#define GEMINI_FEAT_HAS_FLASH (1<<0)
-#define GEMINI_FEAT_HAS_ETH   (1<<1)
-#define GEMINI_FEAT_HAS_SCSI  (1<<2)
-#define GEMINI_FEAT_HAS_P0    (1<<3)
-#define GEMINI_FEAT_FAM_MASK  0xf0
-
-/* Mod/ECO bit definitions */
-#define GEMINI_ECO_LEVEL_MASK 0x0f
-#define GEMINI_MOD_MASK       0xf0
-
-/* Type/revision bit definitions */
-#define GEMINI_REV_MASK       0x0f
-#define GEMINI_TYPE_MASK      0xf0
-
-/* User switch definitions */
-#define GEMINI_SWITCH_VERBOSE    1     /* adds "debug" to boot cmd line */
-#define GEMINI_SWITCH_SINGLE_USER 7    /* boots into "single-user" mode */
-
-#define SGS_RTC_CONTROL  0
-#define SGS_RTC_SECONDS  1
-#define SGS_RTC_MINUTES  2
-#define SGS_RTC_HOURS    3
-#define SGS_RTC_DAY      4
-#define SGS_RTC_DAY_OF_MONTH 5
-#define SGS_RTC_MONTH    6
-#define SGS_RTC_YEAR     7
-
-#define SGS_RTC_SET  0x80
-#define SGS_RTC_IS_STOPPED 0x80
-
-#define GRACKLE_CONFIG_ADDR_ADDR  (0xfec00000)
-#define GRACKLE_CONFIG_DATA_ADDR  (0xfee00000)
-
-#define GEMINI_BOOT_INIT  (0xfff00100)
-
-#ifndef __ASSEMBLY__
-
-static inline void grackle_write( unsigned long addr, unsigned long data )
-{
-  __asm__ __volatile__(
-  " stwbrx %1, 0, %0\n \
-    sync\n \
-    stwbrx %3, 0, %2\n \
-    sync "
-  : /* no output */
-  : "r" (GRACKLE_CONFIG_ADDR_ADDR), "r" (addr),
-    "r" (GRACKLE_CONFIG_DATA_ADDR), "r" (data));
-}
-
-static inline unsigned long grackle_read( unsigned long addr )
-{
-  unsigned long val;
-
-  __asm__ __volatile__(
-  " stwbrx %1, 0, %2\n \
-    sync\n \
-    lwbrx %0, 0, %3\n \
-    sync "
-  : "=r" (val)
-  : "r" (addr), "r" (GRACKLE_CONFIG_ADDR_ADDR),
-    "r" (GRACKLE_CONFIG_DATA_ADDR));
-
-  return val;
-}
-
-static inline void gemini_led_on( int led )
-{
-  if (led >= 0 && led < GEMINI_LEDS)
-    *(unsigned char *)(GEMINI_LEDBASE + (led<<3)) = 1;
-}
-
-static inline void gemini_led_off(int led)
-{
-  if (led >= 0 && led < GEMINI_LEDS)
-    *(unsigned char *)(GEMINI_LEDBASE + (led<<3)) = 0;
-}
-
-static inline int gemini_led_val(int led)
-{
-  int val = 0;
-  if (led >= 0 && led < GEMINI_LEDS)
-    val = *(unsigned char *)(GEMINI_LEDBASE + (led<<3));
-  return (val & 0x1);
-}
-
-/* returns processor id from the board */
-static inline int gemini_processor(void)
-{
-  unsigned char cpu = *(unsigned char *)(GEMINI_CPUSTAT);
-  return (int) ((cpu == 0) ? 4 : (cpu & GEMINI_CPU_ID_MASK));
-}
-
-
-extern void _gemini_reboot(void);
-extern void gemini_prom_init(void);
-extern void gemini_init_l2(void);
-#endif /* __ASSEMBLY__ */
-#endif
-#endif /* __KERNEL__ */
--- linux-2.6.20-rc1-mm1/arch/ppc/platforms/gemini_pci.c	2006-11-29 22:57:37.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,41 +0,0 @@
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/slab.h>
-
-#include <asm/machdep.h>
-#include <platforms/gemini.h>
-#include <asm/byteorder.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/pci-bridge.h>
-
-void __init gemini_pcibios_fixup(void)
-{
-	int i;
-	struct pci_dev *dev = NULL;
-	
-	for_each_pci_dev(dev) {
-		for(i = 0; i < 6; i++) {
-			if (dev->resource[i].flags & IORESOURCE_IO) {
-				dev->resource[i].start |= (0xfe << 24);
-				dev->resource[i].end |= (0xfe << 24);
-			}
-		}
-	}
-}
-
-
-/* The "bootloader" for Synergy boards does none of this for us, so we need to
-   lay it all out ourselves... --Dan */
-void __init gemini_find_bridges(void)
-{
-	struct pci_controller* hose;
-	
-	ppc_md.pcibios_fixup = gemini_pcibios_fixup;
-
-	hose = pcibios_alloc_controller();
-	if (!hose)
-		return;
-	setup_indirect_pci(hose, 0xfec00000, 0xfee00000);
-}
--- linux-2.6.20-rc1-mm1/arch/ppc/platforms/gemini_prom.S	2006-11-29 22:57:37.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,90 +0,0 @@
-/*
- *  Not really prom support code (yet), but sort of anti-prom code.  The current
- *  bootloader does a number of things it shouldn't and doesn't do things that it
- *  should.  The stuff in here is mainly a hodge-podge collection of setup code
- *  to get the board up and running.
- *    ---Dan
- */
-
-#include <asm/reg.h>
-#include <asm/page.h>
-#include <platforms/gemini.h>
-#include <asm/ppc_asm.h>
-
-/*
- *  On 750's the MMU is on when Linux is booted, so we need to clear out the
- *  bootloader's BAT settings, make sure we're in supervisor state (gotcha!),
- *  and turn off the MMU.
- *
- */
-
-_GLOBAL(gemini_prom_init)
-#ifdef CONFIG_SMP
-	/* Since the MMU's on, get stuff in rom space that we'll need */
-	lis	r4,GEMINI_CPUSTAT@h
-	ori	r4,r4,GEMINI_CPUSTAT@l
-	lbz	r5,0(r4)
-	andi.	r5,r5,3
-	mr	r24,r5		/* cpu # used later on */
-#endif
-	mfmsr	r4
-	li	r3,MSR_PR	/* ensure supervisor! */
-	ori	r3,r3,MSR_IR|MSR_DR
-	andc	r4,r4,r3
-	mtmsr	r4
-	isync
-#if 0
-	/* zero out the bats now that the MMU is off */
-prom_no_mmu:	
-	li	r3,0
-        mtspr   SPRN_IBAT0U,r3
-        mtspr   SPRN_IBAT0L,r3
-        mtspr   SPRN_IBAT1U,r3
-        mtspr   SPRN_IBAT1L,r3
-        mtspr   SPRN_IBAT2U,r3
-        mtspr   SPRN_IBAT2L,r3
-        mtspr   SPRN_IBAT3U,r3
-        mtspr   SPRN_IBAT3L,r3
-
-        mtspr   SPRN_DBAT0U,r3
-        mtspr   SPRN_DBAT0L,r3
-        mtspr   SPRN_DBAT1U,r3
-        mtspr   SPRN_DBAT1L,r3
-        mtspr   SPRN_DBAT2U,r3
-	mtspr   SPRN_DBAT2L,r3
-        mtspr   SPRN_DBAT3U,r3
-        mtspr   SPRN_DBAT3L,r3
-#endif
-
-	/* the bootloader (as far as I'm currently aware) doesn't mess with page
-	   tables, but since we're already here, might as well zap these, too */
-	li	r4,0
-	mtspr	SPRN_SDR1,r4
-
-	li	r4,16
-	mtctr	r4
-	li	r3,0
-	li	r4,0
-3:	mtsrin	r3,r4
-	addi	r3,r3,1
-	bdnz	3b
-
-#ifdef CONFIG_SMP
-	/* The 750 book (and Mot/IBM support) says that this will "assist" snooping
-	   when in SMP.  Not sure yet whether this should stay or leave... */
-	mfspr	r4,SPRN_HID0
-	ori	r4,r4,HID0_ABE
-	mtspr	SPRN_HID0,r4
-	sync
-#endif /* CONFIG_SMP */
-	blr
-
-/*  apparently, SMon doesn't pay attention to HID0[SRST].  Disable the MMU and
-    branch to 0xfff00100 */
-_GLOBAL(_gemini_reboot)
-	lis	r5,GEMINI_BOOT_INIT@h
-	ori	r5,r5,GEMINI_BOOT_INIT@l
-	li	r6,MSR_IP
-	mtspr	SPRN_SRR0,r5
-	mtspr	SPRN_SRR1,r6
-	rfi
--- linux-2.6.20-rc1-mm1/arch/ppc/platforms/gemini_serial.h	2006-11-29 22:57:37.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,40 +0,0 @@
-#ifdef __KERNEL__
-#ifndef __ASMPPC_GEMINI_SERIAL_H
-#define __ASMPPC_GEMINI_SERIAL_H
-
-#include <platforms/gemini.h>
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define RS_TABLE_SIZE  64
-#else
-#define RS_TABLE_SIZE  4
-#endif
-
-/* Rate for the 24.576 Mhz clock for the onboard serial chip */
-#define BASE_BAUD  (24576000 / 16)
-
-#ifdef CONFIG_SERIAL_DETECT_IRQ
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_SKIP_TEST|ASYNC_AUTO_IRQ)
-#define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_AUTO_IRQ)
-#else
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_SKIP_TEST)
-#define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF)
-#endif
-
-#define STD_SERIAL_PORT_DEFNS \
-        { 0, BASE_BAUD, GEMINI_SERIAL_A, 15, STD_COM_FLAGS }, /* ttyS0 */ \
-        { 0, BASE_BAUD, GEMINI_SERIAL_B, 14, STD_COM_FLAGS }, /* ttyS1 */ \
-
-#ifdef CONFIG_GEMINI_PU32
-#define PU32_SERIAL_PORT_DEFNS \
-        { 0, BASE_BAUD, NULL, 0, STD_COM_FLAGS },
-#else
-#define PU32_SERIAL_PORT_DEFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
-        STD_SERIAL_PORT_DEFNS \
-        PU32_SERIAL_PORT_DEFNS
-
-#endif
-#endif /* __KERNEL__ */
--- linux-2.6.20-rc1-mm1/arch/ppc/platforms/gemini_setup.c	2006-11-29 22:57:37.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,577 +0,0 @@
-/*
- *  Copyright (C) 1995 Linus Torvalds
- *  Adapted from 'alpha' version by Gary Thomas
- *  Modified by Cort Dougan (cort@cs.nmt.edu)
- *  Synergy Microsystems board support by Dan Cox (dan@synergymicro.com)
- *
- */
-
-#include <linux/stddef.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/reboot.h>
-#include <linux/pci.h>
-#include <linux/time.h>
-#include <linux/kdev_t.h>
-#include <linux/types.h>
-#include <linux/major.h>
-#include <linux/initrd.h>
-#include <linux/console.h>
-#include <linux/seq_file.h>
-#include <linux/root_dev.h>
-#include <linux/bcd.h>
-
-#include <asm/system.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <asm/dma.h>
-#include <asm/io.h>
-#include <asm/m48t35.h>
-#include <platforms/gemini.h>
-#include <asm/time.h>
-#include <asm/open_pic.h>
-#include <asm/bootinfo.h>
-#include <asm/machdep.h>
-
-void gemini_find_bridges(void);
-static int gemini_get_clock_speed(void);
-extern void gemini_pcibios_fixup(void);
-
-static char *gemini_board_families[] = {
-  "VGM", "VSS", "KGM", "VGR", "VCM", "VCS", "KCM", "VCR"
-};
-static int gemini_board_count = sizeof(gemini_board_families) /
-                                 sizeof(gemini_board_families[0]);
-
-static unsigned int cpu_7xx[16] = {
-	0, 15, 14, 0, 0, 13, 5, 9, 6, 11, 8, 10, 16, 12, 7, 0
-};
-static unsigned int cpu_6xx[16] = {
-	0, 0, 14, 0, 0, 13, 5, 9, 6, 11, 8, 10, 0, 12, 7, 0
-};
-
-/*
- * prom_init is the Gemini version of prom.c:prom_init.  We only need
- * the BSS clearing code, so I copied that out of prom.c.  This is a
- * lot simpler than hacking prom.c so it will build with Gemini. -VAL
- */
-
-#define PTRRELOC(x)	((typeof(x))((unsigned long)(x) + offset))
-
-unsigned long
-prom_init(void)
-{
-	unsigned long offset = reloc_offset();
-	unsigned long phys;
-	extern char __bss_start, _end;
-
-	/* First zero the BSS -- use memset, some arches don't have
-	 * caches on yet */
-	memset_io(PTRRELOC(&__bss_start),0 , &_end - &__bss_start);
-
- 	/* Default */
- 	phys = offset + KERNELBASE;
-
-	gemini_prom_init();
-
-	return phys;
-}
-
-int
-gemini_show_cpuinfo(struct seq_file *m)
-{
-	unsigned char reg, rev;
-	char *family;
-	unsigned int type;
-
-	reg = readb(GEMINI_FEAT);
-	family = gemini_board_families[((reg>>4) & 0xf)];
-	if (((reg>>4) & 0xf) > gemini_board_count)
-		printk(KERN_ERR "cpuinfo(): unable to determine board family\n");
-
-	reg = readb(GEMINI_BREV);
-	type = (reg>>4) & 0xf;
-	rev = reg & 0xf;
-
-	reg = readb(GEMINI_BECO);
-
-	seq_printf(m, "machine\t\t: Gemini %s%d, rev %c, eco %d\n",
-		   family, type, (rev + 'A'), (reg & 0xf));
-
-	seq_printf(m, "board\t\t: Gemini %s", family);
-	if (type > 9)
-		seq_printf(m, "%c", (type - 10) + 'A');
-	else
-		seq_printf(m, "%d", type);
-
-	seq_printf(m, ", rev %c, eco %d\n", (rev + 'A'), (reg & 0xf));
-
-	seq_printf(m, "clock\t\t: %dMhz\n", gemini_get_clock_speed());
-
-	return 0;
-}
-
-static u_char gemini_openpic_initsenses[] = {
-	1,
-	1,
-	1,
-	1,
-	0,
-	0,
-	1, /* remainder are level-triggered */
-};
-
-#define GEMINI_MPIC_ADDR (0xfcfc0000)
-#define GEMINI_MPIC_PCI_CFG (0x80005800)
-
-void __init gemini_openpic_init(void)
-{
-
-	OpenPIC_Addr = (volatile struct OpenPIC *)
-		grackle_read(GEMINI_MPIC_PCI_CFG + 0x10);
-	OpenPIC_InitSenses = gemini_openpic_initsenses;
-	OpenPIC_NumInitSenses = sizeof( gemini_openpic_initsenses );
-
-	ioremap( GEMINI_MPIC_ADDR, OPENPIC_SIZE);
-}
-
-
-extern unsigned long loops_per_jiffy;
-extern int root_mountflags;
-extern char cmd_line[];
-
-void
-gemini_heartbeat(void)
-{
-	static unsigned long led = GEMINI_LEDBASE+(4*8);
-	static char direction = 8;
-
-
-	/* We only want to do this on 1 CPU */
-	if (smp_processor_id())
-		return;
-	*(char *)led = 0;
-	if ( (led + direction) > (GEMINI_LEDBASE+(7*8)) ||
-	     (led + direction) < (GEMINI_LEDBASE+(4*8)) )
-		direction *= -1;
-	led += direction;
-	*(char *)led = 0xff;
-	ppc_md.heartbeat_count = ppc_md.heartbeat_reset;
-}
-
-void __init gemini_setup_arch(void)
-{
-	extern char cmd_line[];
-
-
-	loops_per_jiffy = 50000000/HZ;
-
-#ifdef CONFIG_BLK_DEV_INITRD
-	/* bootable off CDROM */
-	if (initrd_start)
-		ROOT_DEV = Root_SR0;
-	else
-#endif
-		ROOT_DEV = Root_SDA1;
-
-	/* nothing but serial consoles... */
-	sprintf(cmd_line, "%s console=ttyS0", cmd_line);
-
-	printk("Boot arguments: %s\n", cmd_line);
-
-	ppc_md.heartbeat = gemini_heartbeat;
-	ppc_md.heartbeat_reset = HZ/8;
-	ppc_md.heartbeat_count = 1;
-
-	/* Lookup PCI hosts */
-	gemini_find_bridges();
-	/* take special pains to map the MPIC, since it isn't mapped yet */
-	gemini_openpic_init();
-	/* start the L2 */
-	gemini_init_l2();
-}
-
-
-int
-gemini_get_clock_speed(void)
-{
-	unsigned long hid1, pvr;
-	int clock;
-
-	pvr = mfspr(SPRN_PVR);
-	hid1 = (mfspr(SPRN_HID1) >> 28) & 0xf;
-	if (PVR_VER(pvr) == 8 ||
-	    PVR_VER(pvr) == 12)
-		hid1 = cpu_7xx[hid1];
-	else
-		hid1 = cpu_6xx[hid1];
-
-	switch((readb(GEMINI_BSTAT) & 0xc) >> 2) {
-
-	case 0:
-	default:
-		clock = (hid1*100)/3;
-		break;
-
-	case 1:
-		clock = (hid1*125)/3;
-		break;
-
-	case 2:
-		clock = (hid1*50);
-		break;
-	}
-
-	return clock;
-}
-
-void __init gemini_init_l2(void)
-{
-        unsigned char reg, brev, fam, creg;
-        unsigned long cache;
-        unsigned long pvr;
-
-        reg = readb(GEMINI_L2CFG);
-        brev = readb(GEMINI_BREV);
-        fam = readb(GEMINI_FEAT);
-        pvr = mfspr(SPRN_PVR);
-
-        switch(PVR_VER(pvr)) {
-
-        case 8:
-                if (reg & 0xc0)
-                        cache = (((reg >> 6) & 0x3) << 28);
-                else
-                        cache = 0x3 << 28;
-
-#ifdef CONFIG_SMP
-                /* Pre-3.0 processor revs had snooping errata.  Leave
-                   their L2's disabled with SMP. -- Dan */
-                if (PVR_CFG(pvr) < 3) {
-                        printk("Pre-3.0 750; L2 left disabled!\n");
-                        return;
-                }
-#endif /* CONFIG_SMP */
-
-                /* Special case: VGM5-B's came before L2 ratios were set on
-                   the board.  Processor speed shouldn't be too high, so
-                   set L2 ratio to 1:1.5.  */
-                if ((brev == 0x51) && ((fam & 0xa0) >> 4) == 0)
-                        reg |= 1;
-
-                /* determine best cache ratio based upon what the board
-                   tells us (which sometimes _may_ not be true) and
-                   the processor speed. */
-                else {
-                        if (gemini_get_clock_speed() > 250)
-                                reg = 2;
-                }
-                break;
-        case 12:
-	{
-		static unsigned long l2_size_val = 0;
-
-		if (!l2_size_val)
-			l2_size_val = _get_L2CR();
-		cache = l2_size_val;
-                break;
-	}
-        case 4:
-        case 9:
-                creg = readb(GEMINI_CPUSTAT);
-                if (((creg & 0xc) >> 2) != 1)
-                        printk("Dual-604 boards don't support the use of L2\n");
-                else
-                        writeb(1, GEMINI_L2CFG);
-                return;
-        default:
-                printk("Unknown processor; L2 left disabled\n");
-                return;
-        }
-
-        cache |= ((1<<reg) << 25);
-        cache |= (L2CR_L2RAM_MASK|L2CR_L2CTL|L2CR_L2DO);
-        _set_L2CR(0);
-        _set_L2CR(cache | L2CR_L2E);
-
-}
-
-void
-gemini_restart(char *cmd)
-{
-	local_irq_disable();
-	/* make a clean restart, not via the MPIC */
-	_gemini_reboot();
-	for(;;);
-}
-
-void
-gemini_power_off(void)
-{
-	for(;;);
-}
-
-void
-gemini_halt(void)
-{
-	gemini_restart(NULL);
-}
-
-void __init gemini_init_IRQ(void)
-{
-	/* gemini has no 8259 */
-	openpic_init(1, 0, 0, -1);
-}
-
-#define gemini_rtc_read(x)       (readb(GEMINI_RTC+(x)))
-#define gemini_rtc_write(val,x)  (writeb((val),(GEMINI_RTC+(x))))
-
-/* ensure that the RTC is up and running */
-long __init gemini_time_init(void)
-{
-	unsigned char reg;
-
-	reg = gemini_rtc_read(M48T35_RTC_CONTROL);
-
-	if ( reg & M48T35_RTC_STOPPED ) {
-		printk(KERN_INFO "M48T35 real-time-clock was stopped. Now starting...\n");
-		gemini_rtc_write((reg & ~(M48T35_RTC_STOPPED)), M48T35_RTC_CONTROL);
-		gemini_rtc_write((reg | M48T35_RTC_SET), M48T35_RTC_CONTROL);
-	}
-	return 0;
-}
-
-#undef DEBUG_RTC
-
-unsigned long
-gemini_get_rtc_time(void)
-{
-	unsigned int year, mon, day, hour, min, sec;
-	unsigned char reg;
-
-	reg = gemini_rtc_read(M48T35_RTC_CONTROL);
-	gemini_rtc_write((reg|M48T35_RTC_READ), M48T35_RTC_CONTROL);
-#ifdef DEBUG_RTC
-	printk("get rtc: reg = %x\n", reg);
-#endif
-
-	do {
-		sec = gemini_rtc_read(M48T35_RTC_SECONDS);
-		min = gemini_rtc_read(M48T35_RTC_MINUTES);
-		hour = gemini_rtc_read(M48T35_RTC_HOURS);
-		day = gemini_rtc_read(M48T35_RTC_DOM);
-		mon = gemini_rtc_read(M48T35_RTC_MONTH);
-		year = gemini_rtc_read(M48T35_RTC_YEAR);
-	} while( sec != gemini_rtc_read(M48T35_RTC_SECONDS));
-#ifdef DEBUG_RTC
-	printk("get rtc: sec=%x, min=%x, hour=%x, day=%x, mon=%x, year=%x\n",
-	       sec, min, hour, day, mon, year);
-#endif
-
-	gemini_rtc_write(reg, M48T35_RTC_CONTROL);
-
-	BCD_TO_BIN(sec);
-	BCD_TO_BIN(min);
-	BCD_TO_BIN(hour);
-	BCD_TO_BIN(day);
-	BCD_TO_BIN(mon);
-	BCD_TO_BIN(year);
-
-	if ((year += 1900) < 1970)
-		year += 100;
-#ifdef DEBUG_RTC
-	printk("get rtc: sec=%x, min=%x, hour=%x, day=%x, mon=%x, year=%x\n",
-	       sec, min, hour, day, mon, year);
-#endif
-
-	return mktime( year, mon, day, hour, min, sec );
-}
-
-
-int
-gemini_set_rtc_time( unsigned long now )
-{
-	unsigned char reg;
-	struct rtc_time tm;
-
-	to_tm( now, &tm );
-
-	reg = gemini_rtc_read(M48T35_RTC_CONTROL);
-#ifdef DEBUG_RTC
-	printk("set rtc: reg = %x\n", reg);
-#endif
-
-	gemini_rtc_write((reg|M48T35_RTC_SET), M48T35_RTC_CONTROL);
-#ifdef DEBUG_RTC
-	printk("set rtc: tm vals - sec=%x, min=%x, hour=%x, mon=%x, mday=%x, year=%x\n",
-	       tm.tm_sec, tm.tm_min, tm.tm_hour, tm.tm_mon, tm.tm_mday, tm.tm_year);
-#endif
-
-	tm.tm_year -= 1900;
-	BIN_TO_BCD(tm.tm_sec);
-	BIN_TO_BCD(tm.tm_min);
-	BIN_TO_BCD(tm.tm_hour);
-	BIN_TO_BCD(tm.tm_mon);
-	BIN_TO_BCD(tm.tm_mday);
-	BIN_TO_BCD(tm.tm_year);
-#ifdef DEBUG_RTC
-	printk("set rtc: tm vals - sec=%x, min=%x, hour=%x, mon=%x, mday=%x, year=%x\n",
-	       tm.tm_sec, tm.tm_min, tm.tm_hour, tm.tm_mon, tm.tm_mday, tm.tm_year);
-#endif
-
-	gemini_rtc_write(tm.tm_sec, M48T35_RTC_SECONDS);
-	gemini_rtc_write(tm.tm_min, M48T35_RTC_MINUTES);
-	gemini_rtc_write(tm.tm_hour, M48T35_RTC_HOURS);
-	gemini_rtc_write(tm.tm_mday, M48T35_RTC_DOM);
-	gemini_rtc_write(tm.tm_mon, M48T35_RTC_MONTH);
-	gemini_rtc_write(tm.tm_year, M48T35_RTC_YEAR);
-
-	/* done writing */
-	gemini_rtc_write(reg, M48T35_RTC_CONTROL);
-
-	return 0;
-}
-
-/*  use the RTC to determine the decrementer count */
-void __init gemini_calibrate_decr(void)
-{
-	int freq, divisor;
-	unsigned char reg;
-
-	/* determine processor bus speed */
-	reg = readb(GEMINI_BSTAT);
-
-	switch(((reg & 0x0c)>>2)&0x3) {
-	case 0:
-	default:
-		freq = 66667;
-		break;
-	case 1:
-		freq = 83000;
-		break;
-	case 2:
-		freq = 100000;
-		break;
-	}
-
-	freq *= 1000;
-	divisor = 4;
-	tb_ticks_per_jiffy = freq / HZ / divisor;
-	tb_to_us = mulhwu_scale_factor(freq/divisor, 1000000);
-}
-
-unsigned long __init gemini_find_end_of_memory(void)
-{
-	unsigned long total;
-	unsigned char reg;
-
-	reg = readb(GEMINI_MEMCFG);
-	total = ((1<<((reg & 0x7) - 1)) *
-		 (8<<((reg >> 3) & 0x7)));
-	total *= (1024*1024);
-	return total;
-}
-
-static void __init
-gemini_map_io(void)
-{
-	io_block_mapping(0xf0000000, 0xf0000000, 0x10000000, _PAGE_IO);
-	io_block_mapping(0x80000000, 0x80000000, 0x10000000, _PAGE_IO);
-}
-
-#ifdef CONFIG_SMP
-static int
-smp_gemini_probe(void)
-{
-	int i, nr;
-
-        nr = (readb(GEMINI_CPUSTAT) & GEMINI_CPU_COUNT_MASK) >> 2;
-	if (nr == 0)
-		nr = 4;
-
-	if (nr > 1) {
-		openpic_request_IPIs();
-		for (i = 1; i < nr; ++i)
-			smp_hw_index[i] = i;
-	}
-
-	return nr;
-}
-
-static void
-smp_gemini_kick_cpu(int nr)
-{
-	openpic_reset_processor_phys(1 << nr);
-	openpic_reset_processor_phys(0);
-}
-
-static void
-smp_gemini_setup_cpu(int cpu_nr)
-{
-	if (OpenPIC_Addr)
-		do_openpic_setup_cpu();
-	if (cpu_nr > 0)
-		gemini_init_l2();
-}
-
-static struct smp_ops_t gemini_smp_ops = {
-	smp_openpic_message_pass,
-	smp_gemini_probe,
-	smp_gemini_kick_cpu,
-	smp_gemini_setup_cpu,
-	.give_timebase = smp_generic_give_timebase,
-	.take_timebase = smp_generic_take_timebase,
-};
-#endif /* CONFIG_SMP */
-
-void __init platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
-			  unsigned long r6, unsigned long r7)
-{
-	int i;
-
-	/* Restore BATs for now */
-	mtspr(SPRN_DBAT3U, 0xf0001fff);
-	mtspr(SPRN_DBAT3L, 0xf000002a);
-
-	parse_bootinfo(find_bootinfo());
-
-	for(i = 0; i < GEMINI_LEDS; i++)
-		gemini_led_off(i);
-
-	ISA_DMA_THRESHOLD = 0;
-	DMA_MODE_READ = 0;
-	DMA_MODE_WRITE = 0;
-
-#ifdef CONFIG_BLK_DEV_INITRD
-	if ( r4 )
-	{
-		initrd_start = r4 + KERNELBASE;
-		initrd_end = r5 + KERNELBASE;
-	}
-#endif
-
-	ppc_md.setup_arch = gemini_setup_arch;
-	ppc_md.show_cpuinfo = gemini_show_cpuinfo;
-	ppc_md.init_IRQ = gemini_init_IRQ;
-	ppc_md.get_irq = openpic_get_irq;
-	ppc_md.init = NULL;
-
-	ppc_md.restart = gemini_restart;
-	ppc_md.power_off = gemini_power_off;
-	ppc_md.halt = gemini_halt;
-
-	ppc_md.time_init = gemini_time_init;
-	ppc_md.set_rtc_time = gemini_set_rtc_time;
-	ppc_md.get_rtc_time = gemini_get_rtc_time;
-	ppc_md.calibrate_decr = gemini_calibrate_decr;
-
-	ppc_md.find_end_of_memory = gemini_find_end_of_memory;
-	ppc_md.setup_io_mappings = gemini_map_io;
-
-	ppc_md.pcibios_fixup_bus = gemini_pcibios_fixup;
-
-#ifdef CONFIG_SMP
-	smp_ops = &gemini_smp_ops;
-#endif /* CONFIG_SMP */
-}
--- linux-2.6.20-rc1-mm1/arch/ppc/configs/gemini_defconfig	2006-11-29 22:57:37.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,618 +0,0 @@
-#
-# Automatically generated make config: don't edit
-#
-CONFIG_MMU=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_HAVE_DEC_LOCK=y
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-
-#
-# General setup
-#
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-# CONFIG_BSD_PROCESS_ACCT is not set
-CONFIG_SYSCTL=y
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_EMBEDDED is not set
-CONFIG_FUTEX=y
-CONFIG_EPOLL=y
-
-#
-# Loadable module support
-#
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_MODULE_FORCE_UNLOAD is not set
-CONFIG_OBSOLETE_MODPARM=y
-# CONFIG_MODVERSIONS is not set
-CONFIG_KMOD=y
-
-#
-# Platform support
-#
-CONFIG_PPC=y
-CONFIG_PPC32=y
-CONFIG_6xx=y
-# CONFIG_40x is not set
-# CONFIG_POWER3 is not set
-# CONFIG_8xx is not set
-
-#
-# IBM 4xx options
-#
-# CONFIG_8260 is not set
-CONFIG_GENERIC_ISA_DMA=y
-CONFIG_PPC_STD_MMU=y
-# CONFIG_PPC_MULTIPLATFORM is not set
-# CONFIG_APUS is not set
-# CONFIG_WILLOW_2 is not set
-# CONFIG_PCORE is not set
-# CONFIG_POWERPMC250 is not set
-# CONFIG_EV64260 is not set
-# CONFIG_SPRUCE is not set
-# CONFIG_LOPEC is not set
-# CONFIG_MCPN765 is not set
-# CONFIG_MVME5100 is not set
-# CONFIG_PPLUS is not set
-# CONFIG_PRPMC750 is not set
-# CONFIG_PRPMC800 is not set
-# CONFIG_SANDPOINT is not set
-# CONFIG_ADIR is not set
-# CONFIG_K2 is not set
-# CONFIG_PAL4 is not set
-CONFIG_GEMINI=y
-# CONFIG_SMP is not set
-# CONFIG_PREEMPT is not set
-CONFIG_ALTIVEC=y
-CONFIG_TAU=y
-# CONFIG_TAU_INT is not set
-# CONFIG_TAU_AVERAGE is not set
-# CONFIG_CPU_FREQ is not set
-
-#
-# General setup
-#
-# CONFIG_HIGHMEM is not set
-CONFIG_PCI=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_KCORE_ELF=y
-CONFIG_BINFMT_ELF=y
-CONFIG_KERNEL_ELF=y
-# CONFIG_BINFMT_MISC is not set
-CONFIG_PCI_LEGACY_PROC=y
-CONFIG_PCI_NAMES=y
-# CONFIG_HOTPLUG is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-# CONFIG_PPC601_SYNC_FIX is not set
-# CONFIG_CMDLINE_BOOL is not set
-
-#
-# Advanced setup
-#
-# CONFIG_ADVANCED_OPTIONS is not set
-
-#
-# Default settings for advanced configuration options are used
-#
-CONFIG_HIGHMEM_START=0xfe000000
-CONFIG_LOWMEM_SIZE=0x30000000
-CONFIG_KERNEL_START=0xc0000000
-CONFIG_TASK_SIZE=0x80000000
-CONFIG_BOOT_LOAD=0x00800000
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNP is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_DEV_FD is not set
-# CONFIG_BLK_CPQ_DA is not set
-# CONFIG_BLK_CPQ_CISS_DA is not set
-# CONFIG_BLK_DEV_DAC960 is not set
-# CONFIG_BLK_DEV_UMEM is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_INITRD=y
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# ATA/IDE/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI support
-#
-CONFIG_SCSI=y
-
-#
-# SCSI support type (disk, tape, CD-ROM)
-#
-CONFIG_BLK_DEV_SD=y
-# CONFIG_CHR_DEV_ST is not set
-# CONFIG_CHR_DEV_OSST is not set
-CONFIG_BLK_DEV_SR=y
-CONFIG_BLK_DEV_SR_VENDOR=y
-CONFIG_CHR_DEV_SG=y
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
-# CONFIG_SCSI_MULTI_LUN is not set
-# CONFIG_SCSI_REPORT_LUNS is not set
-CONFIG_SCSI_CONSTANTS=y
-# CONFIG_SCSI_LOGGING is not set
-
-#
-# SCSI low-level drivers
-#
-# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
-# CONFIG_SCSI_ACARD is not set
-# CONFIG_SCSI_AACRAID is not set
-# CONFIG_SCSI_AIC7XXX is not set
-# CONFIG_SCSI_AIC7XXX_OLD is not set
-# CONFIG_SCSI_AIC79XX is not set
-# CONFIG_SCSI_DPT_I2O is not set
-# CONFIG_SCSI_ADVANSYS is not set
-# CONFIG_SCSI_IN2000 is not set
-# CONFIG_SCSI_AM53C974 is not set
-# CONFIG_SCSI_MEGARAID is not set
-# CONFIG_SCSI_BUSLOGIC is not set
-# CONFIG_SCSI_CPQFCTS is not set
-# CONFIG_SCSI_DMX3191D is not set
-# CONFIG_SCSI_EATA is not set
-# CONFIG_SCSI_EATA_PIO is not set
-# CONFIG_SCSI_FUTURE_DOMAIN is not set
-# CONFIG_SCSI_GDTH is not set
-# CONFIG_SCSI_GENERIC_NCR5380 is not set
-# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
-# CONFIG_SCSI_INITIO is not set
-# CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_NCR53C7xx is not set
-CONFIG_SCSI_SYM53C8XX_2=y
-CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
-CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
-CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
-# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
-# CONFIG_SCSI_PCI2000 is not set
-# CONFIG_SCSI_PCI2220I is not set
-# CONFIG_SCSI_QLOGIC_ISP is not set
-# CONFIG_SCSI_QLOGIC_FC is not set
-# CONFIG_SCSI_QLOGIC_1280 is not set
-# CONFIG_SCSI_DC395x is not set
-# CONFIG_SCSI_DC390T is not set
-# CONFIG_SCSI_U14_34F is not set
-# CONFIG_SCSI_NSP32 is not set
-# CONFIG_SCSI_DEBUG is not set
-
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support (EXPERIMENTAL)
-#
-# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
-# CONFIG_I2O is not set
-
-#
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-# CONFIG_NETLINK_DEV is not set
-CONFIG_NETFILTER=y
-# CONFIG_NETFILTER_DEBUG is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-# CONFIG_IP_PNP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_INET_ECN is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-
-#
-# IP: Netfilter Configuration
-#
-# CONFIG_IP_NF_CONNTRACK is not set
-# CONFIG_IP_NF_QUEUE is not set
-# CONFIG_IP_NF_IPTABLES is not set
-# CONFIG_IP_NF_ARPTABLES is not set
-# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
-# CONFIG_IP_NF_COMPAT_IPFWADM is not set
-# CONFIG_IPV6 is not set
-# CONFIG_XFRM_USER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-CONFIG_IPV6_SCTP__=y
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_LLC is not set
-# CONFIG_DECNET is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_HW_FLOWCONTROL is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-CONFIG_NETDEVICES=y
-
-#
-# ARCnet devices
-#
-# CONFIG_ARCNET is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_ETHERTAP is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
-# CONFIG_OAKNET is not set
-# CONFIG_HAPPYMEAL is not set
-# CONFIG_SUNGEM is not set
-# CONFIG_NET_VENDOR_3COM is not set
-
-#
-# Tulip family network device support
-#
-# CONFIG_NET_TULIP is not set
-# CONFIG_HP100 is not set
-# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-# CONFIG_ACENIC is not set
-# CONFIG_DL2K is not set
-# CONFIG_E1000 is not set
-# CONFIG_NS83820 is not set
-# CONFIG_HAMACHI is not set
-# CONFIG_YELLOWFIN is not set
-# CONFIG_R8169 is not set
-# CONFIG_SK98LIN is not set
-# CONFIG_TIGON3 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
-# CONFIG_IXGB is not set
-# CONFIG_FDDI is not set
-# CONFIG_HIPPI is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Token Ring devices (depends on LLC=y)
-#
-# CONFIG_NET_FC is not set
-# CONFIG_RCPCI is not set
-# CONFIG_SHAPER is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-
-#
-# Amateur Radio support
-#
-# CONFIG_HAMRADIO is not set
-
-#
-# IrDA (infrared) support
-#
-# CONFIG_IRDA is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN_BOOL is not set
-
-#
-# Graphics support
-#
-# CONFIG_FB is not set
-
-#
-# Old CD-ROM drivers (not SCSI, not IDE)
-#
-# CONFIG_CD_NO_IDESCSI is not set
-
-#
-# Input device support
-#
-# CONFIG_INPUT is not set
-
-#
-# Userland interfaces
-#
-
-#
-# Input I/O drivers
-#
-# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
-# CONFIG_SERIO is not set
-
-#
-# Input Device Drivers
-#
-
-#
-# Macintosh device drivers
-#
-
-#
-# Character devices
-#
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_SERIAL_8250_EXTENDED is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-CONFIG_UNIX98_PTY_COUNT=256
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# I2C Hardware Sensors Mainboard support
-#
-
-#
-# I2C Hardware Sensors Chip support
-#
-# CONFIG_I2C_SENSOR is not set
-
-#
-# Mice
-#
-# CONFIG_BUSMOUSE is not set
-# CONFIG_QIC02_TAPE is not set
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_NVRAM is not set
-CONFIG_GEN_RTC=y
-# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
-# CONFIG_FTAPE is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_HANGCHECK_TIMER is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_JBD is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-# CONFIG_XFS_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_QUOTA is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-CONFIG_ISO9660_FS=y
-# CONFIG_JOLIET is not set
-# CONFIG_ZISOFS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_FAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_DEVFS_FS=y
-# CONFIG_DEVFS_MOUNT is not set
-# CONFIG_DEVFS_DEBUG is not set
-CONFIG_DEVPTS_FS=y
-# CONFIG_DEVPTS_FS_XATTR is not set
-CONFIG_TMPFS=y
-CONFIG_RAMFS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-CONFIG_NFSD=y
-# CONFIG_NFSD_V3 is not set
-# CONFIG_NFSD_TCP is not set
-CONFIG_LOCKD=y
-CONFIG_EXPORTFS=y
-CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_GSS is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_INTERMEZZO_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_ACORN_PARTITION is not set
-# CONFIG_OSF_PARTITION is not set
-# CONFIG_AMIGA_PARTITION is not set
-# CONFIG_ATARI_PARTITION is not set
-# CONFIG_MAC_PARTITION is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_BSD_DISKLABEL is not set
-# CONFIG_MINIX_SUBPARTITION is not set
-CONFIG_SOLARIS_X86_PARTITION=y
-# CONFIG_UNIXWARE_DISKLABEL is not set
-# CONFIG_LDM_PARTITION is not set
-# CONFIG_NEC98_PARTITION is not set
-# CONFIG_SGI_PARTITION is not set
-# CONFIG_ULTRIX_PARTITION is not set
-# CONFIG_SUN_PARTITION is not set
-# CONFIG_EFI_PARTITION is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# USB support
-#
-# CONFIG_USB is not set
-# CONFIG_USB_GADGET is not set
-
-#
-# Bluetooth support
-#
-# CONFIG_BT is not set
-
-#
-# Library routines
-#
-# CONFIG_CRC32 is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_KALLSYMS is not set
-
-#
-# Security options
-#
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-# CONFIG_CRYPTO is not set

--- linux-2.6.20-rc4-mm1/include/asm-ppc/m48t35.h	2007-01-12 07:51:09.000000000 +0100
+++ /dev/null	2006-09-19 00:45:31.000000000 +0200
@@ -1,77 +0,0 @@
-/*
- *  Registers for the SGS-Thomson M48T35 Timekeeper RAM chip
- *  and
- *  Registers for the SGS-Thomson M48T37 Timekeeper RAM chip
- *  The 37 is the 35 plus alarm and century thus the offsets
- *  are shifted by the extra registers.
- */
-
-#ifndef __PPC_M48T35_H
-#define __PPC_M48T35_H
-
-/* RTC offsets */
-#define M48T35_RTC_FLAGS	(-8)	/* the negative regs are really T37 only */
-#define M48T35_RTC_CENTURY	(-7)
-#define M48T35_RTC_AL_SEC	(-6)
-#define M48T35_RTC_AL_MIN	(-5)
-#define M48T35_RTC_AL_HRS	(-4)
-#define M48T35_RTC_AL_DOM	(-3)
-#define M48T35_RTC_INTERRUPT	(-2)
-#define M48T35_RTC_WATCHDOG	(-1)
-#define M48T35_RTC_CONTROL	0	/* T35 starts here */
-#define M48T35_RTC_SECONDS	1
-#define M48T35_RTC_MINUTES	2
-#define M48T35_RTC_HOURS	3
-#define M48T35_RTC_DAY		4
-#define M48T35_RTC_DOM		5
-#define M48T35_RTC_MONTH	6
-#define M48T35_RTC_YEAR		7
-
-/* this way help us know which bits go with which regs */
-#define M48T35_RTC_FLAGS_BL           0x10
-#define M48T35_RTC_FLAGS_AF           0x40
-#define M48T35_RTC_FLAGS_WDF          0x80
-
-#define M48T35_RTC_INTERRUPT_AFE       0x80
-#define M48T35_RTC_INTERRUPT_ABE       0x20
-#define M48T35_RTC_INTERRUPT_ALL       (M48T35_RTC_INTERRUPT_AFE|M48T35_RTC_INTERRUPT_ABE)
-
-#define M48T35_RTC_WATCHDOG_RB         0x03
-#define M48T35_RTC_WATCHDOG_BMB        0x7c
-#define M48T35_RTC_WATCHDOG_WDS        0x80
-#define M48T35_RTC_WATCHDOG_ALL        (M48T35_RTC_WATCHDOG_RB|M48T35_RTC_WATCHDOG_BMB|M48T35_RTC_W)
-
-#define M48T35_RTC_CONTROL_WRITE       0x80
-#define M48T35_RTC_CONTROL_READ        0x40
-#define M48T35_RTC_CONTROL_CAL_SIGN    0x20
-#define M48T35_RTC_CONTROL_CAL_VALUE   0x1f
-#define M48T35_RTC_CONTROL_LOCKED      (M48T35_RTC_WRITE|M48T35_RTC_READ)
-#define M48T35_RTC_CONTROL_CALIBRATION (M48T35_RTC_CONTROL_CAL_SIGN|M48T35_RTC_CONTROL_CAL_VALUE)
-
-#define M48T35_RTC_SECONDS_SEC_1       0x0f
-#define M48T35_RTC_SECONDS_SEC_10      0x70
-#define M48T35_RTC_SECONDS_ST          0x80
-#define M48T35_RTC_SECONDS_SEC_ALL     (M48T35_RTC_SECONDS_SEC_1|M48T35_RTC_SECONDS_SEC_10)
-
-#define M48T35_RTC_MINUTES_MIN_1       0x0f
-#define M48T35_RTC_MINUTES_MIN_10      0x70
-#define M48T35_RTC_MINUTES_MIN_ALL     (M48T35_RTC_MINUTES_MIN_1|M48T35_RTC_MINUTES_MIN_10)
-
-#define M48T35_RTC_HOURS_HRS_1         0x0f
-#define M48T35_RTC_HOURS_HRS_10        0x30
-#define M48T35_RTC_HOURS_HRS_ALL       (M48T35_RTC_HOURS_HRS_1|M48T35_RTC_HOURS_HRS_10)
-
-#define M48T35_RTC_DAY_DAY_1           0x03
-#define M48T35_RTC_DAY_FT              0x40
-
-#define M48T35_RTC_ALARM_OFF           0x00
-#define M48T35_RTC_WATCHDOG_OFF        0x00
-
-
-/* legacy */
-#define M48T35_RTC_SET      0x80
-#define M48T35_RTC_STOPPED  0x80
-#define M48T35_RTC_READ     0x40
-
-
-#endif


^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2007-01-14  9:15 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-11-24 23:49 RFC: powerpc: remove GEMINI support? Adrian Bunk
2006-12-19  4:12 ` [2.6 patch] powerpc: remove the broken Gemini support Adrian Bunk
2006-12-19 16:13   ` Kumar Gala
2006-12-19 17:28     ` Roman Zippel
2006-12-20  5:27       ` Paul Mackerras
2007-01-14  9:15 Adrian Bunk

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).