On Mon, Jan 15, 2007 at 10:58:29AM -0500, Alan Stern wrote:
> On Sun, 14 Jan 2007, Florin Iucha wrote:
> 
> > Jiri and Trond,
> > 
> > On Mon, Jan 15, 2007 at 01:14:09AM +0100, Jiri Kosina wrote:
> > > On Sun, 14 Jan 2007, Florin Iucha wrote:
> > > 
> > > > All the testing was done via a ssh into the workstation.  The console 
> > > > was left as booted into, with the gdm running.  The remote nfs4 
> > > > directory was mounted on "/mnt". After copying the 60+ GB and testing 
> > > > that the keyboard was still functioning, I did not reboot but stayed in 
> > > > the same kernel and pulled the latest git then started bisecting.  
> > > 
> > > Hi Florin,
> > > 
> > > thanks a lot for the testing. Just to verify - what kernel is 'the same 
> > > kernel' mentioned above? (just to isolate whether the problem is really 
> > > somewhere between 2.6.19 and 2.6.20-rc2, as you stated in previous posts, 
> > > or the situation has changed).
> > 
> > This happened with 2.6.19.  It worked last time, but I wanted to test
> > again, to make sure.  This time, it bombed, but half an hour after the 
> > transfer finished.
> > 
> > > > After recompiling, I moved over to the workstation to reboot it, but the 
> > > > keyboard was not functioning ;(
> > > 
> > > So this time the hang occured when the system was idle, not during the 
> > > transfers, right?
> > 
> > Yes it was idle.  Immediately after the transfer finished, the keyboard was
> > still functioning.  It "hang" minutes later, after the first bisected kernel
> > was compiled and installed.
> > 
> > > > I ran "lsusb" and it displayed all the devices. "dmesg" did not show
> > > > any oops, anything for that matter.  I have unplugged the keyboard and
> > > > run "lsusb" again, but it hang.  I ran "ls /mnt" and it hang as well.
> > > > Stracing "lsusb" showed it hang (entered the kernel) at opening the device
> > > > that used to be the keyboard.  Stracing "ls /mnt" showed that it
> > > > hang at "stat(/mnt)".  Both processes were in "D" state.  "ls /root"
> > > > worked without problem, so it appears that crossing mountpoints causes
> > > > some hang in the kernel.
> > > 
> > > Could you please do alt-sysrq-t (or "echo t > /proc/sysrq-trigger" via 
> > > ssh, when your keyboard is dead) to see the calltraces of the processes 
> > > which are stuck inside kernel?
> > > 
> > > You will probably get a lot of output after the sysrq, so please either 
> > > put it somewhere on the web if possible, or just extract the interesting 
> > > processes out of it (mainly the ones which are stuck).
> > 
> > Will do.
> 
> It would be nice to learn exactly why the keyboard stopped working.  Try
> using the usbmon facility (instructions in Documentation/usb/usbmon.txt)
> to see what happens when you type on the dead keyboard.  Be sure to turn
> on CONFIG_USB_DEBUG as well.  And also check /proc/interrupts; each time
> you hit a key the USB controller should get an interrupt.

Attached is the output from usbmon, unfortunately this kernel did not
have CONFIG_USB_DEBUG set.  This is kernel 2.6.20-rc5.

So, the bus sees some traffic when the keyboard is used, but gdm does
not receive any keystrokes.

florin

-- 
Bruce Schneier expects the Spanish Inquisition.
      http://geekz.co.uk/schneierfacts/fact/163