LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd
@ 2007-02-17 13:13 Prakash Punnoor
  2007-02-17 15:05 ` Prakash Punnoor
  0 siblings, 1 reply; 4+ messages in thread
From: Prakash Punnoor @ 2007-02-17 13:13 UTC (permalink / raw)
  To: Alan; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 3270 bytes --]

Hi,

I tried a cat /dev/sdb1 >/dev/null from a Sandisk Extreme III CF card 
connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf 
2.6.20 on x86_64. For a few seconds it worked but then it dropped to pio4:

ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: (BMDMA stat 0x65)
ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb 0x0 data 65536 in
         res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
ata3: soft resetting port
ata3.00: simplex DMA is claimed by other device, disabling DMA
ata3.00: configured for PIO4
ata3: EH complete
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA


While boot I get:
sata_nv 0000:00:0e.0: version 3.2
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 22 (level, low) -> 
IRQ 22
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 22
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 22
scsi0 : sata_nv
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 1
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x977
scsi 0:0:0:0: Direct-Access     ATA      Maxtor 7V300F0   VA11 PQ: 0 ANSI: 5
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
pata_amd 0000:00:0d.0: version 0.2.7
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ata3: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF400 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF408 irq 15
scsi2 : pata_amd
ata3.00: CFA, max MWDMA2, 2001888 sectors: LBA
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for MWDMA2
scsi3 : pata_amd
ata4: port disabled. ignoring.
ata4: reset failed, giving up
scsi 2:0:0:0: Direct-Access     ATA      SanDisk SDCFX-10 HDX  PQ: 0 ANSI: 5
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
 sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg1 type 0

-- 
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V

[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd
  2007-02-17 13:13 exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd Prakash Punnoor
@ 2007-02-17 15:05 ` Prakash Punnoor
  2007-02-18 15:44   ` Prakash Punnoor
  0 siblings, 1 reply; 4+ messages in thread
From: Prakash Punnoor @ 2007-02-17 15:05 UTC (permalink / raw)
  To: Alan; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 3661 bytes --]

Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
> Hi,
>
> I tried a cat /dev/sdb1 >/dev/null from a Sandisk Extreme III CF card
> connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf
> 2.6.20 on x86_64. For a few seconds it worked but then it dropped to pio4:
>
> ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata3.00: (BMDMA stat 0x65)
> ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb 0x0 data 65536
> in res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask 0x2 (HSM violation) ata3:
> soft resetting port
> ata3.00: simplex DMA is claimed by other device, disabling DMA
> ata3.00: configured for PIO4
> ata3: EH complete
> SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
>
>
> While boot I get:
> sata_nv 0000:00:0e.0: version 3.2
> ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
> ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 22 (level, low)
> -> IRQ 22
> PCI: Setting latency timer of device 0000:00:0e.0 to 64
> ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 22
> ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 22
> scsi0 : sata_nv
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32)
> ata1.00: ata1: dev 0 multi count 1
> ata1.00: configured for UDMA/133
> scsi1 : sata_nv
> ata2: SATA link down (SStatus 0 SControl 300)
> ATA: abnormal status 0x7F on port 0x977
> scsi 0:0:0:0: Direct-Access     ATA      Maxtor 7V300F0   VA11 PQ: 0 ANSI:
> 5 SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
> SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
>  sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3
> sd 0:0:0:0: Attached scsi disk sda
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> pata_amd 0000:00:0d.0: version 0.2.7
> PCI: Setting latency timer of device 0000:00:0d.0 to 64
> ata3: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF400 irq 14
> ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF408 irq 15
> scsi2 : pata_amd
> ata3.00: CFA, max MWDMA2, 2001888 sectors: LBA
> ata3.00: ata3: dev 0 multi count 0
> ata3.00: configured for MWDMA2
> scsi3 : pata_amd
> ata4: port disabled. ignoring.
> ata4: reset failed, giving up
> scsi 2:0:0:0: Direct-Access     ATA      SanDisk SDCFX-10 HDX  PQ: 0 ANSI:
> 5 SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
> SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support
> DPO or FUA
>  sdb: sdb1
> sd 2:0:0:0: Attached scsi removable disk sdb
> sd 2:0:0:0: Attached scsi generic sg1 type 0

The ide driver worked better - for a short time and then this happens:

hda: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: DMA disabled

Any idea?

-- 
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V

[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd
  2007-02-17 15:05 ` Prakash Punnoor
@ 2007-02-18 15:44   ` Prakash Punnoor
  2007-02-19  9:48     ` Prakash Punnoor
  0 siblings, 1 reply; 4+ messages in thread
From: Prakash Punnoor @ 2007-02-18 15:44 UTC (permalink / raw)
  To: Alan; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 2341 bytes --]

Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
> Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
> > Hi,
> >
> > I tried a cat /dev/sdb1 >/dev/null from a Sandisk Extreme III CF card
> > connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf
> > 2.6.20 on x86_64. For a few seconds it worked but then it dropped to
> > pio4:
> >
> > ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> > ata3.00: (BMDMA stat 0x65)
> > ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb 0x0 data 65536
> > in res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > ata3: soft resetting port
> > ata3.00: simplex DMA is claimed by other device, disabling DMA
> > ata3.00: configured for PIO4
> > ata3: EH complete
> > SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
> > sdb: Write Protect is off
> > sdb: Mode Sense: 00 3a 00 00
> > SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
> > support DPO or FUA
> >
[...]
>
> The ide driver worked better - for a short time and then this happens:
>
> hda: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
> ide: failed opcode was: unknown
> hda: DMA disabled

I connected the cf to ide adapter to an ide to sata adapter and using this 
combination on sata_nv makes no troubkes whatsoever. So what goues wrong with 
pata_amd/amd ide driver? BTW, I found specs for the cf card on the sandisk 
website. Perhaps someone wants to check whether the amd drivers deal 
corretcly with the true ide mode implemented in the cf card?

http://www.sandisk.com/Assets/File/OEM/Manuals/ProdManCFlashv11.0.pdf


scsi 1:0:0:0: Direct-Access     ATA      SanDisk SDCFX-10 HDX  PQ: 0 ANSI: 5
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
 sdb: sdb1
sd 1:0:0:0: Attached scsi removable disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0


-- 
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V

[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd
  2007-02-18 15:44   ` Prakash Punnoor
@ 2007-02-19  9:48     ` Prakash Punnoor
  0 siblings, 0 replies; 4+ messages in thread
From: Prakash Punnoor @ 2007-02-19  9:48 UTC (permalink / raw)
  To: Alan; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 2060 bytes --]

Am Sonntag 18 Februar 2007 schrieb Prakash Punnoor:
> Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
> > Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
> > > Hi,
> > >
> > > I tried a cat /dev/sdb1 >/dev/null from a Sandisk Extreme III CF card
> > > connected via cf to IDE adapteer to onboard ide of nforce c51. I am
> > > usinf 2.6.20 on x86_64. For a few seconds it worked but then it dropped
> > > to pio4:
> > >
> > > ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> > > ata3.00: (BMDMA stat 0x65)
> > > ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb 0x0 data
> > > 65536 in res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask 0x2 (HSM
> > > violation) ata3: soft resetting port
> > > ata3.00: simplex DMA is claimed by other device, disabling DMA
> > > ata3.00: configured for PIO4
> > > ata3: EH complete
> > > SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
> > > sdb: Write Protect is off
> > > sdb: Mode Sense: 00 3a 00 00
> > > SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
> > > support DPO or FUA
>
> [...]
>
> > The ide driver worked better - for a short time and then this happens:
> >
> > hda: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
> > ide: failed opcode was: unknown
> > hda: DMA disabled
>
> I connected the cf to ide adapter to an ide to sata adapter and using this
> combination on sata_nv makes no troubkes whatsoever. So what goues wrong
> with pata_amd/amd ide driver? BTW, I found specs for the cf card on the
> sandisk website. Perhaps someone wants to check whether the amd drivers
> deal corretcly with the true ide mode implemented in the cf card?
>
> http://www.sandisk.com/Assets/File/OEM/Manuals/ProdManCFlashv11.0.pdf

For what it's worth: I tried the cd-ide adapter with the sandisk cf on another 
machine with ide uli/ali driver and here I don't have any problems as well. 
So everything points to amd driver...

-- 
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V

[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2007-02-19  9:48 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-02-17 13:13 exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd Prakash Punnoor
2007-02-17 15:05 ` Prakash Punnoor
2007-02-18 15:44   ` Prakash Punnoor
2007-02-19  9:48     ` Prakash Punnoor

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).