LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
@ 2008-04-09 20:30 Tvrtko A. Ursulin
  2008-04-13  3:11 ` Tejun Heo
  0 siblings, 1 reply; 8+ messages in thread
From: Tvrtko A. Ursulin @ 2008-04-09 20:30 UTC (permalink / raw)
  To: linux-ide, linux-kernel


Hi all,

When running smartctl to get the attributes readout libata seems to get
really confused on my system. After a timeout it recovers without apparent
ill-effect, but the reported values are complete rubbish. Unfortunately I don't
remember if this is a regression or it was always like this..

I have attached some data below, but if more is needed just shout!

Regards,

Tvrtko

root@sol:~# uname -a
Linux sol 2.6.24.3 #4 SMP PREEMPT Sat Mar 8 12:57:56 GMT 2008 x86_64 GNU/Linux

root@sol:~# smartctl -A /dev/sda
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 17018
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
255 Unknown_Attribute       0x373f   200   016   063    Pre-fail  Always   In_the_past 69269232549888
 45 Unknown_Attribute       0x4344   087   082   068    Old_age   Offline      -       61779704492097
 51 Unknown_Attribute       0x0039   000   000   057    Pre-fail  Offline  FAILING_NOW 52987850404480
 66 Unknown_Attribute       0x3231   048   068   049    Pre-fail  Offline  FAILING_NOW 55350388793431
 48 Unknown_Attribute       0x4130   065   083   048    Old_age   Offline      -       71675860037707
 32 Unknown_Attribute       0x2030   032   032   048    Old_age   Offline  FAILING_NOW 35322350018592
 32 Unknown_Attribute       0x2020   032   032   032    Old_age   Offline  FAILING_NOW 550026354720
 16 Unknown_Attribute       0x3f00   000   016   000    Old_age   Offline  FAILING_NOW 280379760114684
255 Unknown_Attribute       0x000f   000   007   015    Pre-fail  Always   FAILING_NOW 131943408599808
120 Unknown_Attribute       0x7800   000   000   000    Old_age   Offline  FAILING_NOW 0
 64 Unknown_Attribute       0xfe00   001   000   000    Old_age   Offline  In_the_past 39030002838272
104 Unknown_Attribute       0x4174   188   035   116    Old_age   Offline  In_the_past 48379254046529
225 Load_Cycle_Count        0x484e   000   085   078    Old_age   Always   FAILING_NOW 86
144 Unknown_Attribute       0x0016   000   000   022    Old_age   Always   FAILING_NOW 0



[ 7846.128079] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[ 7846.128086] ata2.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 0
[ 7846.128087]          res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 7846.128090] ata2.00: status: { DRDY }
[ 7846.128096] ata2: hard resetting link
[ 7846.735912] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7846.760523] ata2.00: configured for UDMA/133
[ 7846.760530] ata2: EH complete
[ 7846.760546] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 7846.760556] sd 1:0:0:0: [sda] Write Protect is off
[ 7846.760558] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7846.760571] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7852.748405] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[ 7852.748412] ata2.00: cmd b0/d1:01:01:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[ 7852.748413]          res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 7852.748416] ata2.00: status: { DRDY }
[ 7852.748421] ata2: hard resetting link
[ 7853.356244] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7853.378276] ata2.00: configured for UDMA/133
[ 7853.378284] ata2: EH complete
[ 7853.378416] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 7853.378519] sd 1:0:0:0: [sda] Write Protect is off
[ 7853.378521] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7853.378761] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

00:0e.0 SATA controller: nVidia Corporation Unknown device 07f4 (rev a2) (prog-if 01 [AHCI 1.0])
        Subsystem: Giga-byte Technology Unknown device b002
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 316
        Region 0: I/O ports at 09f0 [size=8]
        Region 1: I/O ports at 0bf0 [size=4]
        Region 2: I/O ports at 0970 [size=8]
        Region 3: I/O ports at 0b70 [size=4]
        Region 4: I/O ports at dc00 [size=16]
        Region 5: Memory at e5104000 (32-bit, non-prefetchable) [size=8K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [8c] #12 [0010]
        Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+
                Address: 00000000fee0100c  Data: 4181

root@sol:~# lsscsi
[1:0:0:0]    disk    ATA      WDC WD3200AAKS-0 12.0  /dev/sda
[2:0:0:0]    cd/dvd  TSSTcorp CDDVDW SH-S203N  SB01  /dev/scd0


root@sol:~# lsmod | grep -e "a[th][ac]"
ahci                   27524  8
ata_generic             6404  0
libata                152048  2 ahci,ata_generic
scsi_mod              152752  5 firewire_sbp2,sg,sr_mod,sd_mod,libata




^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-04-09 20:30 libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI Tvrtko A. Ursulin
@ 2008-04-13  3:11 ` Tejun Heo
  2008-04-13  7:34   ` Tvrtko A. Ursulin
  0 siblings, 1 reply; 8+ messages in thread
From: Tejun Heo @ 2008-04-13  3:11 UTC (permalink / raw)
  To: Tvrtko A. Ursulin; +Cc: linux-ide, linux-kernel

Tvrtko A. Ursulin wrote:
> Hi all,
> 
> When running smartctl to get the attributes readout libata seems to get
> really confused on my system. After a timeout it recovers without apparent
> ill-effect, but the reported values are complete rubbish. Unfortunately I don't
> remember if this is a regression or it was always like this..
> 
> I have attached some data below, but if more is needed just shout!
> 
> Regards,
> 
> Tvrtko
> 
> root@sol:~# uname -a
> Linux sol 2.6.24.3 #4 SMP PREEMPT Sat Mar 8 12:57:56 GMT 2008 x86_64 GNU/Linux
> 
> root@sol:~# smartctl -A /dev/sda
> smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
> Home page is http://smartmontools.sourceforge.net/
> 
> === START OF READ SMART DATA SECTION ===
> SMART Attributes Data Structure revision number: 17018
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
> 255 Unknown_Attribute       0x373f   200   016   063    Pre-fail  Always   In_the_past 69269232549888
>  45 Unknown_Attribute       0x4344   087   082   068    Old_age   Offline      -       61779704492097
>  51 Unknown_Attribute       0x0039   000   000   057    Pre-fail  Offline  FAILING_NOW 52987850404480
>  66 Unknown_Attribute       0x3231   048   068   049    Pre-fail  Offline  FAILING_NOW 55350388793431
>  48 Unknown_Attribute       0x4130   065   083   048    Old_age   Offline      -       71675860037707
>  32 Unknown_Attribute       0x2030   032   032   048    Old_age   Offline  FAILING_NOW 35322350018592
>  32 Unknown_Attribute       0x2020   032   032   032    Old_age   Offline  FAILING_NOW 550026354720
>  16 Unknown_Attribute       0x3f00   000   016   000    Old_age   Offline  FAILING_NOW 280379760114684
> 255 Unknown_Attribute       0x000f   000   007   015    Pre-fail  Always   FAILING_NOW 131943408599808
> 120 Unknown_Attribute       0x7800   000   000   000    Old_age   Offline  FAILING_NOW 0
>  64 Unknown_Attribute       0xfe00   001   000   000    Old_age   Offline  In_the_past 39030002838272
> 104 Unknown_Attribute       0x4174   188   035   116    Old_age   Offline  In_the_past 48379254046529
> 225 Load_Cycle_Count        0x484e   000   085   078    Old_age   Always   FAILING_NOW 86
> 144 Unknown_Attribute       0x0016   000   000   022    Old_age   Always   FAILING_NOW 0
> 
> 
> 
> [ 7846.128079] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> [ 7846.128086] ata2.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 0
> [ 7846.128087]          res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 7846.128090] ata2.00: status: { DRDY }
> [ 7846.128096] ata2: hard resetting link
> [ 7846.735912] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 7846.760523] ata2.00: configured for UDMA/133
> [ 7846.760530] ata2: EH complete
> [ 7846.760546] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 7846.760556] sd 1:0:0:0: [sda] Write Protect is off
> [ 7846.760558] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 7846.760571] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 7852.748405] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> [ 7852.748412] ata2.00: cmd b0/d1:01:01:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
> [ 7852.748413]          res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 7852.748416] ata2.00: status: { DRDY }
> [ 7852.748421] ata2: hard resetting link
> [ 7853.356244] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 7853.378276] ata2.00: configured for UDMA/133
> [ 7853.378284] ata2: EH complete
> [ 7853.378416] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 7853.378519] sd 1:0:0:0: [sda] Write Protect is off
> [ 7853.378521] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 7853.378761] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> 
> 00:0e.0 SATA controller: nVidia Corporation Unknown device 07f4 (rev a2) (prog-if 01 [AHCI 1.0])
>         Subsystem: Giga-byte Technology Unknown device b002
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 0 (750ns min, 250ns max)
>         Interrupt: pin A routed to IRQ 316
>         Region 0: I/O ports at 09f0 [size=8]
>         Region 1: I/O ports at 0bf0 [size=4]
>         Region 2: I/O ports at 0970 [size=8]
>         Region 3: I/O ports at 0b70 [size=4]
>         Region 4: I/O ports at dc00 [size=16]
>         Region 5: Memory at e5104000 (32-bit, non-prefetchable) [size=8K]
>         Capabilities: [44] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>         Capabilities: [8c] #12 [0010]
>         Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+
>                 Address: 00000000fee0100c  Data: 4181
> 
> root@sol:~# lsscsi
> [1:0:0:0]    disk    ATA      WDC WD3200AAKS-0 12.0  /dev/sda
> [2:0:0:0]    cd/dvd  TSSTcorp CDDVDW SH-S203N  SB01  /dev/scd0
> 
> 
> root@sol:~# lsmod | grep -e "a[th][ac]"
> ahci                   27524  8
> ata_generic             6404  0
> libata                152048  2 ahci,ata_generic
> scsi_mod              152752  5 firewire_sbp2,sg,sr_mod,sd_mod,libata

Is auto spindown configured for the drive?

-- 
tejun

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-04-13  3:11 ` Tejun Heo
@ 2008-04-13  7:34   ` Tvrtko A. Ursulin
  2008-04-15  3:10     ` Tejun Heo
  0 siblings, 1 reply; 8+ messages in thread
From: Tvrtko A. Ursulin @ 2008-04-13  7:34 UTC (permalink / raw)
  To: Tejun Heo; +Cc: linux-ide, linux-kernel

On Sunday 13 April 2008 04:11:15 Tejun Heo wrote:
> Is auto spindown configured for the drive?

I don't think so - it's a 3.5" drive with no special PM features - but how to 
tell?

Tvrtko

root@sol:~# hdparm -i /dev/sda

/dev/sda:

 Model=WDC WD3200AAKS-00VYA0                   , FwRev=12.01B02, SerialNo=     
WD-WCARW0059893
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50
 BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=?0?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

root@sol:~# sdparm -a /dev/sda
    /dev/sda: ATA       WDC WD3200AAKS-0  12.0
Read write error recovery mode page:
  AWRE        1
  ARRE        0
  TB          0
  RC          0
  EER         0
  PER         0
  DTE         0
  DCR         0
  RRC         0
  COR_S       0
  HOC         0
  DSOC        0
  WRC         0
  RTL         0
Caching (SBC) mode page:
  IC          0
  ABPF        0
  CAP         0
  DISC        0
  SIZE        0
  WCE         1
  MF          0
  RCD         0
  DRRP        0
  WRP         0
  DPTL        0
  MIPF        0
  MAPF        0
  MAPFC       0
  FSW         0
  LBCSS       0
  DRA         0
  NV_DIS      0
  NCS         0
  CSS         0
Control mode page:
  TST         0
  TMF_ONLY    0
  D_SENSE     0
  GLTSD       1
  RLEC        0
  QAM         0
  QERR        0
  RAC         0
  UA_INTLCK   0
  SWP         0
  ATO         0
  TAS         0
  AUTOLOAD    0
  BTP        -1
  ESTCT      30

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-04-13  7:34   ` Tvrtko A. Ursulin
@ 2008-04-15  3:10     ` Tejun Heo
  2008-04-15  6:21       ` Tvrtko A. Ursulin
  0 siblings, 1 reply; 8+ messages in thread
From: Tejun Heo @ 2008-04-15  3:10 UTC (permalink / raw)
  To: Tvrtko A. Ursulin; +Cc: linux-ide, linux-kernel

Tvrtko A. Ursulin wrote:
> On Sunday 13 April 2008 04:11:15 Tejun Heo wrote:
>> Is auto spindown configured for the drive?
> 
> I don't think so - it's a 3.5" drive with no special PM features - but how to 
> tell?

Hmm... Can you please post the result of "smartctl --version" and 
"smartctl -a > out 2>&1" and dmesg after the smartctl command?

Thanks.

-- 
tejun

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-04-15  3:10     ` Tejun Heo
@ 2008-04-15  6:21       ` Tvrtko A. Ursulin
  2008-05-14  5:44         ` Tejun Heo
  0 siblings, 1 reply; 8+ messages in thread
From: Tvrtko A. Ursulin @ 2008-04-15  6:21 UTC (permalink / raw)
  To: Tejun Heo; +Cc: linux-ide, linux-kernel

[-- Attachment #1: Type: text/plain, Size: 5012 bytes --]

On Tuesday 15 April 2008 04:10:57 Tejun Heo wrote:
> Tvrtko A. Ursulin wrote:
> > On Sunday 13 April 2008 04:11:15 Tejun Heo wrote:
> >> Is auto spindown configured for the drive?
> >
> > I don't think so - it's a 3.5" drive with no special PM features - but
> > how to tell?
>
> Hmm... Can you please post the result of "smartctl --version" and
> "smartctl -a > out 2>&1" and dmesg after the smartctl command?

Yep, pasted and attached below. dmesg is 67k, hope list is happy with that.

Tvrtko

root@sol:~# smartctl --version
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce 
Allen
Home page is http://smartmontools.sourceforge.net/

smartctl comes with ABSOLUTELY NO WARRANTY. This
is free software, and you are welcome to redistribute it
under the terms of the GNU General Public License Version 2.
See http://www.gnu.org for further details.

CVS version IDs of files used to build this code are:
Module: atacmdnames.cpp  revision: 1.15  date: 2006/10/22
  uses: atacmdnames.h    revision: 1.5   date: 2006/04/12
Module: atacmds.cpp      revision: 1.177 date: 2006/10/27
  uses: atacmds.h        revision: 1.83  date: 2006/08/25
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: extern.h         revision: 1.47  date: 2006/09/15
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: scsiata.h        revision: 1.2   date: 2006/07/01
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: ataprint.cpp     revision: 1.171 date: 2006/10/28
  uses: atacmdnames.h    revision: 1.5   date: 2006/04/12
  uses: atacmds.h        revision: 1.83  date: 2006/08/25
  uses: ataprint.h       revision: 1.29  date: 2006/09/17
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: extern.h         revision: 1.47  date: 2006/09/15
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: knowndrives.h    revision: 1.17  date: 2006/08/09
  uses: smartctl.h       revision: 1.24  date: 2006/07/20
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: knowndrives.cpp  revision: 1.156 date: 2006/10/30
  uses: atacmds.h        revision: 1.83  date: 2006/08/25
  uses: ataprint.h       revision: 1.29  date: 2006/09/17
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: extern.h         revision: 1.47  date: 2006/09/15
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: knowndrives.h    revision: 1.17  date: 2006/08/09
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: os_linux.cpp     revision: 1.88  date: 2006/10/25
  uses: atacmds.h        revision: 1.83  date: 2006/08/25
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: os_linux.h       revision: 1.25  date: 2006/08/25
  uses: scsicmds.h       revision: 1.63  date: 2006/11/12
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: scsicmds.cpp     revision: 1.92  date: 2006/11/12
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: extern.h         revision: 1.47  date: 2006/09/15
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: scsicmds.h       revision: 1.63  date: 2006/11/12
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: scsiprint.cpp    revision: 1.119 date: 2006/11/12
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: extern.h         revision: 1.47  date: 2006/09/15
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: scsicmds.h       revision: 1.63  date: 2006/11/12
  uses: scsiprint.h      revision: 1.20  date: 2006/04/12
  uses: smartctl.h       revision: 1.24  date: 2006/07/20
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: smartctl.cpp     revision: 1.156 date: 2006/10/09
  uses: atacmds.h        revision: 1.83  date: 2006/08/25
  uses: ataprint.h       revision: 1.29  date: 2006/09/17
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: extern.h         revision: 1.47  date: 2006/09/15
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: knowndrives.h    revision: 1.17  date: 2006/08/09
  uses: scsicmds.h       revision: 1.63  date: 2006/11/12
  uses: scsiprint.h      revision: 1.20  date: 2006/04/12
  uses: smartctl.h       revision: 1.24  date: 2006/07/20
  uses: utility.h        revision: 1.47  date: 2006/10/09
Module: utility.cpp      revision: 1.62  date: 2006/08/09
  uses: configure.in     revision: 1.122 date: 2006/12/20
  uses: int64.h          revision: 1.16  date: 2006/10/29
  uses: utility.h        revision: 1.47  date: 2006/10/09

smartmontools release 5.37 dated 2006/12/20 at 20:37:59 UTC
smartmontools build host: x86_64-unknown-linux-gnu
smartmontools build configured: 2007/09/12 22:04:20 UTC
smartctl compile dated Sep 12 2007 at 22:04:32
smartmontools configure 
arguments:  '--prefix=/usr' '--sysconfdir=/etc' '--mandir=/usr/share/man' '--with-initscriptdir=/etc/init.d' '--with-docdir=/usr/share/doc/smartmontools' 'CFLAGS=-fsigned-char -Wall -O2'



[-- Attachment #2: out --]
[-- Type: text/plain, Size: 4151 bytes --]

smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD3200AAKS-00VYA0
Serial Number:    WD-WCARW0059893
Firmware Version: 12.01B02
User Capacity:    320,072,933,376 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Tue Apr 15 07:18:40 2008 BST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled

Warning! SMART Attribute Data Structure error: invalid SMART checksum.
Warning! SMART Attribute Thresholds Structure error: invalid SMART checksum.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Total time to complete Offline 
data collection: 		 (   0) seconds.
Offline data collection
capabilities: 			 (0x00) 	Offline data collection not supported.
SMART capabilities:            (0x55c0)	Does not save SMART data before
					entering power-saving mode.
Error logging capability:        (0x90)	Error logging supported.
					General Purpose Logging supported.

SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
255 Unknown_Attribute       0x40ff   018   149   255    Pre-fail  Always   FAILING_NOW 1099503304802
255 Unknown_Attribute       0x10ff   253   034   255    Pre-fail  Always   FAILING_NOW 1099511627648
 16 Unknown_Attribute       0x0000   000   000   000    Old_age   Offline  FAILING_NOW 537001984
180 Unknown_Attribute       0x0076   129   255   118    Old_age   Always       -       255
 34 Unknown_Attribute       0xff80   255   255   128    Old_age   Offline      -       268501247
 87 Unknown_Attribute       0x0056   129   255   086    Old_age   Always       -       424013611263
255 Unknown_Attribute       0x00ff   000   000   255    Pre-fail  Always   FAILING_NOW 211106232532992
144 Unknown_Attribute       0x0076   129   255   118    Old_age   Always       -       280925807907071
255 Unknown_Attribute       0x00ff   001   016   255    Pre-fail  Always   FAILING_NOW 0
 32 Unknown_Attribute       0x0000   000   000   000    Old_age   Offline  FAILING_NOW 422166540288
255 Unknown_Attribute       0xc0ff   028   083   255    Pre-fail  Always   FAILING_NOW 1099503304787
255 Unknown_Attribute       0x10ff   253   034   255    Pre-fail  Always   FAILING_NOW 1099511627648
 16 Unknown_Attribute       0x0000   000   000   000    Old_age   Offline  FAILING_NOW 537001984
 65 Unknown_Attribute       0x0060   129   255   096    Old_age   Offline      -       255
 34 Unknown_Attribute       0xff80   255   255   128    Old_age   Offline      -       268501247
102 Unknown_Attribute       0x0062   129   255   098    Old_age   Always       -       414351491327
255 Unknown_Attribute       0x00ff   000   000   255    Pre-fail  Always   FAILING_NOW 211106232532992
144 Unknown_Attribute       0x0076   129   255   118    Old_age   Always       -       280925807907071
255 Unknown_Attribute       0x00ff   001   016   255    Pre-fail  Always   FAILING_NOW 0
 32 Unknown_Attribute       0x0000   000   000   000    Old_age   Offline  FAILING_NOW 422619164672
255 Unknown_Attribute       0xc0ff   147   084   255    Pre-fail  Always   FAILING_NOW 1099503304789

Warning! SMART ATA Error Log Structure error: invalid SMART checksum.
SMART Error Log Version: 0
No Errors Logged

Warning! SMART Self-Test Log Structure error: invalid SMART checksum.
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision number = 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


Device does not support Selective Self Tests/Logging

[-- Attachment #3: dmesg --]
[-- Type: text/plain, Size: 68952 bytes --]

[    0.000000] Linux version 2.6.24.3 (tvrtko@sol) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #4 SMP PREEMPT Sat Mar 8 12:57:56 GMT 2008
[    0.000000] Command line: root=UUID=5781d9c0-be35-41cc-9eca-64e5d8fffbe4 ro quiet splash
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000077000000 (usable)
[    0.000000]  BIOS-e820: 0000000077000000 - 000000007f000000 (reserved)
[    0.000000]  BIOS-e820: 000000007f000000 - 000000007fdf0000 (usable)
[    0.000000]  BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000e2000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] Entering add_active_range(0, 0, 158) 0 entries of 256 used
[    0.000000] Entering add_active_range(0, 256, 487424) 1 entries of 256 used
[    0.000000] Entering add_active_range(0, 520192, 523760) 2 entries of 256 used
[    0.000000] end_pfn_map = 1048576
[    0.000000] DMI 2.4 present.
[    0.000000] ACPI: RSDP 000F6600, 0014 (r0 GBT   )
[    0.000000] ACPI: RSDT 7FEF3040, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
[    0.000000] ACPI: FACP 7FEF30C0, 0074 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
[    0.000000] ACPI: DSDT 7FEF3180, 52C6 (r1 GBT    GBTUACPI     1000 MSFT  100000C)
[    0.000000] ACPI: FACS 7FEF1800, 0040
[    0.000000] ACPI: HPET 7FEF85C0, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU       98)
[    0.000000] ACPI: MCFG 7FEF8640, 003C (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
[    0.000000] ACPI: APIC 7FEF84C0, 0098 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
[    0.000000] ACPI: SSDT 7FEF8CE0, 02FC (r1  PmRef    CpuPm     3000 INTL 20040311)
[    0.000000] Entering add_active_range(0, 0, 158) 0 entries of 256 used
[    0.000000] Entering add_active_range(0, 256, 487424) 1 entries of 256 used
[    0.000000] Entering add_active_range(0, 520192, 523760) 2 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   DMA32        4096 ->  1048576
[    0.000000]   Normal    1048576 ->  1048576
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0:        0 ->      158
[    0.000000]     0:      256 ->   487424
[    0.000000]     0:   520192 ->   523760
[    0.000000] On node 0 totalpages: 490894
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 1031 pages reserved
[    0.000000]   DMA zone: 2911 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 7104 pages used for memmap
[    0.000000]   DMA32 zone: 479792 pages, LIFO batch:31
[    0.000000]   Normal zone: 0 pages used for memmap
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 (Bootup-CPU)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] Processor #1
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Setting APIC routing to flat
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[    0.000000] swsusp: Registered nosave memory region: 0000000077000000 - 000000007f000000
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000)
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PERCPU: Allocating 32496 bytes of per cpu data
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 482703
[    0.000000] Kernel command line: root=UUID=5781d9c0-be35-41cc-9eca-64e5d8fffbe4 ro quiet splash
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[    0.000000] hpet clockevent registered
[    0.000000] TSC calibrated against HPET
[   16.820956] time.c: Detected 2333.332 MHz processor.
[   16.823422] Console: colour VGA+ 80x25
[   16.823425] console [tty0] enabled
[   16.824597] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[   16.825441] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[   16.825570] Checking aperture...
[   16.840754] Memory: 1922140k/2095040k available (2186k kernel code, 40844k reserved, 1139k data, 220k init)
[   16.840788] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[   16.899786] Calibrating delay using timer specific routine.. 4670.28 BogoMIPS (lpj=2335142)
[   16.899807] Security Framework initialized
[   16.899816] Capability LSM initialized
[   16.899825] Mount-cache hash table entries: 256
[   16.899934] CPU: L1 I cache: 32K, L1 D cache: 32K
[   16.899936] CPU: L2 cache: 4096K
[   16.899937] using mwait in idle threads.
[   16.899939] CPU: Physical Processor ID: 0
[   16.899940] CPU: Processor Core ID: 0
[   16.899945] CPU0: Thermal monitoring enabled (TM2)
[   16.899954] SMP alternatives: switching to UP code
[   16.900359] ACPI: Core revision 20070126
[   16.914056] Using local APIC timer interrupts.
[   16.956833] APIC timer calibration result 20833325
[   16.956835] Detected 20.833 MHz APIC timer.
[   16.956909] SMP alternatives: switching to SMP code
[   16.957202] Booting processor 1/2 APIC 0x1
[   16.968700] Initializing CPU#1
[   17.027699] Calibrating delay using timer specific routine.. 4666.63 BogoMIPS (lpj=2333319)
[   17.027704] CPU: L1 I cache: 32K, L1 D cache: 32K
[   17.027706] CPU: L2 cache: 4096K
[   17.027707] CPU: Physical Processor ID: 0
[   17.027708] CPU: Processor Core ID: 1
[   17.027713] CPU1: Thermal monitoring enabled (TM2)
[   17.028112] Intel(R) Core(TM)2 Duo CPU     E6550  @ 2.33GHz stepping 0b
[   17.028165] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   17.048145] Brought up 2 CPUs
[   17.048324] net_namespace: 120 bytes
[   17.048570] NET: Registered protocol family 16
[   17.048685] ACPI: bus type pci registered
[   17.049815] PCI: Using MMCONFIG at e0000000 - e1ffffff
[   17.050287] mtrr: your CPUs had inconsistent fixed MTRR settings
[   17.050288] mtrr: probably your BIOS does not setup all CPUs.
[   17.050289] mtrr: corrected configuration.
[   17.051277] ACPI: EC: Look up EC in DSDT
[   17.055694] ACPI: Interpreter enabled
[   17.055696] ACPI: (supports S0 S1 S4 S5)
[   17.055707] ACPI: Using IOAPIC for interrupt routing
[   17.062136] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   17.063245] PCI: Transparent bridge - 0000:00:0a.0
[   17.063381] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   17.063556] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[   17.102749] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.102871] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.102992] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 *10 11 14 15)
[   17.103111] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.103230] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.103348] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.103467] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.103587] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.103707] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.103826] ACPI: PCI Interrupt Link [LIGP] (IRQs *5 7 9 10 11 14 15)
[   17.103945] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
[   17.104064] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
[   17.104187] ACPI: PCI Interrupt Link [LU1B] (IRQs 5 7 9 10 11 14 15) *0
[   17.104306] ACPI: PCI Interrupt Link [LU2B] (IRQs 5 7 9 10 11 14 15) *0
[   17.104426] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 *15)
[   17.104545] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
[   17.104668] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.104788] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)
[   17.104910] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[   17.105032] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
[   17.105182] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[   17.105325] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[   17.105467] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
[   17.105612] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[   17.105754] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[   17.105895] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[   17.106037] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[   17.106178] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[   17.106320] ACPI: PCI Interrupt Link [AIGP] (IRQs 20 21 22 23) *0
[   17.106462] ACPI: PCI Interrupt Link [AUBA] (IRQs 20 21 22 23) *0
[   17.106607] ACPI: PCI Interrupt Link [AUB2] (IRQs 20 21 22 23) *0
[   17.106750] ACPI: PCI Interrupt Link [AU1B] (IRQs 20 21 22 23) *0
[   17.106892] ACPI: PCI Interrupt Link [AU2B] (IRQs 20 21 22 23) *0
[   17.107035] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[   17.107178] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[   17.107321] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[   17.107463] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[   17.107607] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[   17.107751] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[   17.107895] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[   17.107988] Linux Plug and Play Support v0.97 (c) Adam Belay
[   17.108007] pnp: PnP ACPI init
[   17.108014] ACPI: bus type pnp registered
[   17.111200] pnp: PnP ACPI: found 12 devices
[   17.111202] ACPI: ACPI bus type pnp unregistered
[   17.111332] PCI: Using ACPI for IRQ routing
[   17.111334] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   17.114602] PCI-GART: No AMD northbridge found.
[   17.114609] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[   17.114612] hpet0: 3 32-bit timers, 25000000 Hz
[   17.116602] Time: tsc clocksource has been installed.
[   17.118665] system 00:01: ioport range 0x1000-0x107f has been reserved
[   17.118668] system 00:01: ioport range 0x1080-0x10ff has been reserved
[   17.118670] system 00:01: ioport range 0x1400-0x147f has been reserved
[   17.118672] system 00:01: ioport range 0x1480-0x14ff has been reserved
[   17.118674] system 00:01: ioport range 0x1800-0x187f has been reserved
[   17.118676] system 00:01: ioport range 0x1880-0x18ff has been reserved
[   17.118678] system 00:01: iomem range 0x0-0x0 could not be reserved
[   17.118681] system 00:01: iomem range 0xfefe0000-0xfefe01ff has been reserved
[   17.118683] system 00:01: iomem range 0xfefe1000-0xfefe10ff has been reserved
[   17.118685] system 00:01: iomem range 0x77000000-0x7effffff could not be reserved
[   17.118690] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[   17.118692] system 00:02: ioport range 0x800-0x87f has been reserved
[   17.118694] system 00:02: ioport range 0x295-0x314 has been reserved
[   17.118696] system 00:02: ioport range 0x290-0x294 has been reserved
[   17.118698] system 00:02: ioport range 0x880-0x88f has been reserved
[   17.118705] system 00:0a: iomem range 0xe0000000-0xe1ffffff could not be reserved
[   17.118710] system 00:0b: iomem range 0xd0000-0xd3fff has been reserved
[   17.118712] system 00:0b: iomem range 0xd6800-0xd7fff has been reserved
[   17.118714] system 00:0b: iomem range 0xf0000-0xfbfff could not be reserved
[   17.118716] system 00:0b: iomem range 0xfc000-0xfffff could not be reserved
[   17.118718] system 00:0b: iomem range 0x7fef0000-0x7fefffff could not be reserved
[   17.118721] system 00:0b: iomem range 0xffff0000-0xffffffff has been reserved
[   17.118723] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
[   17.118725] system 00:0b: iomem range 0x100000-0x7feeffff could not be reserved
[   17.118727] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[   17.118729] system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[   17.119012] PCI: Bridge: 0000:00:0a.0
[   17.119013]   IO window: disabled.
[   17.119016]   MEM window: e5000000-e50fffff
[   17.119017]   PREFETCH window: disabled.
[   17.119019] PCI: Bridge: 0000:00:0b.0
[   17.119020]   IO window: 9000-9fff
[   17.119022]   MEM window: disabled.
[   17.119023]   PREFETCH window: disabled.
[   17.119024] PCI: Bridge: 0000:00:0c.0
[   17.119025]   IO window: b000-bfff
[   17.119027]   MEM window: disabled.
[   17.119028]   PREFETCH window: disabled.
[   17.119029] PCI: Bridge: 0000:00:0d.0
[   17.119031]   IO window: a000-afff
[   17.119032]   MEM window: disabled.
[   17.119033]   PREFETCH window: disabled.
[   17.119038] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   17.119043] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   17.119047] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[   17.119051] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[   17.119057] NET: Registered protocol family 2
[   17.127833] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[   17.128068] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[   17.129443] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[   17.130010] TCP: Hash tables configured (established 262144 bind 65536)
[   17.130012] TCP reno registered
[   17.132985] checking if image is initramfs... it is
[   17.380845] Switched to high resolution mode on CPU 1
[   17.381362] Switched to high resolution mode on CPU 0
[   17.498896] Freeing initrd memory: 4812k freed
[   17.503068] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   17.503072] io scheduler noop registered
[   17.503073] io scheduler anticipatory registered
[   17.503075] io scheduler deadline registered
[   17.503140] io scheduler cfq registered (default)
[   17.520284] Boot video device is 0000:00:10.0
[   17.520397] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   17.520409] assign_interrupt_mode Found MSI capability
[   17.520420] Allocate Port Service[0000:00:0b.0:pcie00]
[   17.520445] Allocate Port Service[0000:00:0b.0:pcie03]
[   17.520480] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[   17.520491] assign_interrupt_mode Found MSI capability
[   17.520499] Allocate Port Service[0000:00:0c.0:pcie00]
[   17.520522] Allocate Port Service[0000:00:0c.0:pcie03]
[   17.520557] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[   17.520567] assign_interrupt_mode Found MSI capability
[   17.520576] Allocate Port Service[0000:00:0d.0:pcie00]
[   17.520599] Allocate Port Service[0000:00:0d.0:pcie03]
[   17.522164] Real Time Clock Driver v1.12ac
[   17.522286] hpet_resources: 0xfeff0000 is busy
[   17.522307] Linux agpgart interface v0.102
[   17.522309] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   17.522403] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   17.522717] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   17.523188] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   17.523272] PNP: No PS/2 controller found. Probing ports directly.
[   17.523591] serio: i8042 KBD port at 0x60,0x64 irq 1
[   17.523594] serio: i8042 AUX port at 0x60,0x64 irq 12
[   17.523661] mice: PS/2 mouse device common for all mice
[   17.523691] cpuidle: using governor ladder
[   17.523693] cpuidle: using governor menu
[   17.523745] TCP cubic registered
[   17.523782] NET: Registered protocol family 1
[   17.523871] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[   17.523877] Freeing unused kernel memory: 220k freed
[   18.634348] fuse init (API version 7.9)
[   18.639655] ACPI: SSDT 7FEF86C0, 022A (r1  PmRef  Cpu0Ist     3000 INTL 20040311)
[   18.639897] ACPI: SSDT 7FEF8B80, 0152 (r1  PmRef  Cpu1Ist     3000 INTL 20040311)
[   18.640037] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   18.640045] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   18.790788] usbcore: registered new interface driver usbfs
[   18.790808] usbcore: registered new interface driver hub
[   18.791177] usbcore: registered new device driver usb
[   18.792065] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.792355] ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 23
[   18.792362] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 23
[   18.793664] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   18.793669] ohci_hcd 0000:00:04.0: OHCI Host Controller
[   18.793766] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
[   18.793780] ohci_hcd 0000:00:04.0: irq 23, io mem 0xe5108000
[   18.821728] SCSI subsystem initialized
[   18.837738] libata version 3.00 loaded.
[   18.846547] usb usb1: configuration #1 chosen from 1 choice
[   18.846565] hub 1-0:1.0: USB hub found
[   18.846570] hub 1-0:1.0: 10 ports detected
[   18.947629] ACPI: PCI Interrupt Link [AUB2] enabled at IRQ 22
[   18.947635] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [AUB2] -> GSI 22 (level, low) -> IRQ 22
[   18.948717] PCI: Setting latency timer of device 0000:00:04.1 to 64
[   18.948721] ehci_hcd 0000:00:04.1: EHCI Host Controller
[   18.948764] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[   18.948788] ehci_hcd 0000:00:04.1: debug port 1
[   18.948790] PCI: cache line size of 32 is not supported by device 0000:00:04.1
[   18.948800] ehci_hcd 0000:00:04.1: irq 22, io mem 0xe5107000
[   18.954250] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   18.954338] usb usb2: configuration #1 chosen from 1 choice
[   18.954357] hub 2-0:1.0: USB hub found
[   18.954362] hub 2-0:1.0: 10 ports detected
[   19.055568] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[   19.055573] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
[   19.111977] firewire_ohci: Added fw-ohci device 0000:01:07.0, OHCI version 1.10
[   19.112013] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[   19.112301] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
[   19.112306] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
[   19.112310] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   19.493288] usb 1-2: new low speed USB device using ohci_hcd and address 2
[   19.611111] firewire_core: created new fw device fw0 (0 config rom retries, S400)
[   19.624655] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1a:4d:59:db:59
[   19.624658] forcedeth 0000:00:0f.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[   19.626547] ahci 0000:00:0e.0: version 3.0
[   19.626791] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
[   19.626795] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 20 (level, low) -> IRQ 20
[   19.628233] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   19.628238] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   19.684889] usb 1-2: configuration #1 chosen from 1 choice
[   19.695856] usbcore: registered new interface driver hiddev
[   19.702000] input: BTC USB Multimedia Cordless Kit   as /class/input/input0
[   19.706904] input: USB HID v1.00 Keyboard [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   19.720252] input: BTC USB Multimedia Cordless Kit   as /class/input/input1
[   19.725902] input,hiddev96: USB HID v1.00 Mouse [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   19.725911] usbcore: registered new interface driver usbhid
[   19.725913] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   20.626248] ahci 0000:00:0e.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[   20.626252] ahci 0000:00:0e.0: flags: 64bit sntf led clo pmp pio 
[   20.626254] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   20.626509] scsi0 : ahci
[   20.626630] scsi1 : ahci
[   20.626723] scsi2 : ahci
[   20.626814] scsi3 : ahci
[   20.626877] ata1: SATA max UDMA/133 abar m8192@0xe5104000 port 0xe5104100 irq 316
[   20.626879] ata2: SATA max UDMA/133 abar m8192@0xe5104000 port 0xe5104180 irq 316
[   20.626880] ata3: SATA max UDMA/133 abar m8192@0xe5104000 port 0xe5104200 irq 316
[   20.626882] ata4: SATA max UDMA/133 abar m8192@0xe5104000 port 0xe5104280 irq 316
[   20.930694] ata1: SATA link down (SStatus 0 SControl 300)
[   21.538595] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   21.555434] ata2.00: ATA-8: WDC WD3200AAKS-00VYA0, 12.01B02, max UDMA/133
[   21.555437] ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
[   21.556174] ata2.00: configured for UDMA/133
[   22.163469] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   22.164555] ata3.00: ATAPI: TSSTcorp CDDVDW SH-S203N, SB01, max UDMA/100, ATAPI AN
[   22.316045] ata3.00: configured for UDMA/100
[   22.619646] ata4: SATA link down (SStatus 0 SControl 300)
[   22.619728] scsi 1:0:0:0: Direct-Access     ATA      WDC WD3200AAKS-0 12.0 PQ: 0 ANSI: 5
[   22.620347] scsi 2:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S203N  SB01 PQ: 0 ANSI: 5
[   22.620424] NFORCE-MCP73: IDE controller (0x10de:0x056c rev 0xa1) at  PCI slot 0000:00:08.0
[   22.620444] NFORCE-MCP73: not 100% native mode: will probe irqs later
[   22.620449] NFORCE-MCP73: 0000:00:08.0 (rev a1) UDMA133 controller
[   22.620453]     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[   22.620458] NFORCE-MCP73: IDE port disabled
[   22.620461] Probing IDE interface ide0...
[   22.625484] Driver 'sd' needs updating - please use bus_type methods
[   22.625529] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   22.625537] sd 1:0:0:0: [sda] Write Protect is off
[   22.625539] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   22.625550] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.625580] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   22.625586] sd 1:0:0:0: [sda] Write Protect is off
[   22.625588] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   22.625599] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.625601]  sda: sda1 sda2 sda3 sda4 <<4>Driver 'sr' needs updating - please use bus_type methods
[   22.633148]  sda5 sda6 sda7 sda8 sda9 >
[   22.659350] sd 1:0:0:0: [sda] Attached SCSI disk
[   22.661687] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   22.661701] sr 2:0:0:0: Attached scsi generic sg1 type 5
[   22.665172] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   22.665174] Uniform CD-ROM driver Revision: 3.20
[   22.665204] sr 2:0:0:0: Attached scsi CD-ROM sr0
[   22.992032] Attempting manual resume
[   22.992034] swsusp: Resume From Partition 8:2
[   22.992035] PM: Checking swsusp image.
[   22.992146] PM: Resume from disk failed.
[   22.995770] JFS: nTxBlock = 8192, nTxLock = 65536
[   27.244643] input: Power Button (FF) as /class/input/input2
[   27.257283] ACPI: Power Button (FF) [PWRF]
[   27.257319] input: Power Button (CM) as /class/input/input3
[   27.273257] ACPI: Power Button (CM) [PWRB]
[   27.812316] nvidia: module license 'NVIDIA' taints kernel.
[   27.842200] input: PC Speaker as /class/input/input4
[   27.980345] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[   27.980349] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 23
[   27.981263] PCI: Setting latency timer of device 0000:00:09.0 to 64
[   28.112692] ACPI: PCI Interrupt Link [AIGP] enabled at IRQ 22
[   28.112695] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [AIGP] -> GSI 22 (level, low) -> IRQ 22
[   28.112701] PCI: Setting latency timer of device 0000:00:10.0 to 64
[   28.112841] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  169.12  Thu Feb 14 17:51:09 PST 2008
[   29.130156] it87: Found IT8718F chip at 0x290, revision 4
[   29.130167] it87: in3 is VCC (+5V)
[   29.134510] coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
[   29.134541] coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
[   29.181796] Adding 2000084k swap on /dev/sda2.  Priority:-1 extents:1 across:2000084k
[   29.643543] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[   30.271222] kjournald starting.  Commit interval 5 seconds
[   30.279044] EXT3 FS on sda1, internal journal
[   30.279048] EXT3-fs: mounted filesystem with ordered data mode.
[   31.709918] No dock devices found.
[   34.487709] NET: Registered protocol family 10
[   34.487889] lo: Disabled Privacy Extensions
[   42.687068] Bluetooth: Core ver 2.11
[   42.687265] NET: Registered protocol family 31
[   42.687268] Bluetooth: HCI device and connection manager initialized
[   42.687270] Bluetooth: HCI socket layer initialized
[   42.694447] Bluetooth: L2CAP ver 2.9
[   42.694452] Bluetooth: L2CAP socket layer initialized
[   42.697192] Bluetooth: RFCOMM socket layer initialized
[   42.697205] Bluetooth: RFCOMM TTY layer initialized
[   42.697206] Bluetooth: RFCOMM ver 1.8
[   43.081739] [4864]: VMCI: Driver initialized.
[   43.081763] [4864]: Module vmmon: registered with major=10 minor=165
[   43.081772] [4864]: Module vmmon: initialized
[   43.165373] /dev/vmnet: open called by PID 4887 (vmnet-bridge)
[   43.165379] /dev/vmnet: hub 0 does not exist, allocating memory.
[   43.165387] /dev/vmnet: port on hub 0 successfully opened
[   43.165398] bridge-eth0: enabling the bridge
[   43.165401] bridge-eth0: up
[   43.165402] bridge-eth0: already up
[   43.165403] bridge-eth0: attached
[   43.190584] /dev/vmnet: open called by PID 4893 (vmnet-netifup)
[   43.190591] /dev/vmnet: hub 1 does not exist, allocating memory.
[   43.190599] /dev/vmnet: port on hub 1 successfully opened
[   43.202172] /dev/vmnet: open called by PID 4909 (vmnet-netifup)
[   43.202256] /dev/vmnet: hub 8 does not exist, allocating memory.
[   43.202331] /dev/vmnet: port on hub 8 successfully opened
[   43.243718] /dev/vmnet: open called by PID 4917 (vmnet-natd)
[   43.243728] /dev/vmnet: port on hub 8 successfully opened
[   43.343152] /dev/vmnet: open called by PID 4924 (vmnet-dhcpd)
[   43.343160] /dev/vmnet: port on hub 8 successfully opened
[   43.362568] /dev/vmnet: open called by PID 4925 (vmnet-dhcpd)
[   43.362574] /dev/vmnet: port on hub 1 successfully opened
[   46.943492] NET: Registered protocol family 17
[   53.601567] vmnet1: no IPv6 routers present
[   53.763505] vmnet8: no IPv6 routers present
[   61.686093] eth0: no IPv6 routers present
[17030.737907]  CIFS VFS: cifs_mount failed w/return code = -13
[17065.594524]  CIFS VFS: cifs_mount failed w/return code = -13
[17118.163561]  CIFS VFS: cifs_mount failed w/return code = -13
[17131.624947]  CIFS VFS: cifs_mount failed w/return code = -13
[17153.254275]  CIFS VFS: cifs_mount failed w/return code = -13
[17179.473085]  CIFS VFS: cifs_mount failed w/return code = -13
[17216.154587]  CIFS VFS: cifs_mount failed w/return code = -13
[26924.992029] bridge-eth0: disabling the bridge
[26924.997939] bridge-eth0: down
[26925.183366] ACPI: PCI interrupt for device 0000:00:0f.0 disabled
[26926.732844] PM: suspend-to-disk mode set to 'shutdown'
[26926.732990] swsusp: Marking nosave pages: 000000000009e000 - 0000000000100000
[26926.732995] swsusp: Marking nosave pages: 0000000077000000 - 000000007f000000
[26926.733716] swsusp: Basic memory bitmaps created
[26926.733717] Syncing filesystems ... done.
[26926.762925] Freezing user space processes ... (elapsed 0.00 seconds) done.
[26926.763241] Freezing remaining freezable tasks ... (elapsed 1.59 seconds) done.
[26928.358493] Shrinking memory...  \b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\b|\bdone (253770 pages freed)
[26930.721021] Freed 1015080 kbytes in 2.36 seconds (430.11 MB/s)
[26930.721023] Suspending console(s)
[26930.921337] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[26930.923012] ACPI handle has no context!
[26930.923241] serial 00:08: disabled
[26930.923277] ACPI handle has no context!
[26930.933325] NVRM: RmPowerManagement: 3
[26931.125955] ACPI: PCI interrupt for device 0000:00:09.0 disabled
[26931.137023] ACPI: PCI interrupt for device 0000:00:04.1 disabled
[26931.147924] ACPI: PCI interrupt for device 0000:00:04.0 disabled
[26931.159324] Disabling non-boot CPUs ...
[26931.264679] CPU 1 is now offline
[26931.264682] SMP alternatives: switching to UP code
[26931.265774] CPU1 is down
[26931.265914] swsusp: critical section: 
[26931.303274] swsusp: Need to copy 120439 pages
[26931.303276] swsusp: Normal pages needed: 120439 + 1024 + 38, available pages: 370448
[   29.894092] Enabling non-boot CPUs ...
[   29.896483] SMP alternatives: switching to SMP code
[   29.897234] Booting processor 1/2 APIC 0x1
[   29.907581] Initializing CPU#1
[   29.967281] Calibrating delay using timer specific routine.. 4666.93 BogoMIPS (lpj=2333466)
[   29.967286] CPU: L1 I cache: 32K, L1 D cache: 32K
[   29.967288] CPU: L2 cache: 4096K
[   29.967290] CPU: Physical Processor ID: 0
[   29.967290] CPU: Processor Core ID: 1
[   29.967687] Intel(R) Core(TM)2 Duo CPU     E6550  @ 2.33GHz stepping 0b
[   29.967729] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   29.987961] CPU1 is up
[   29.988711] Switched to high resolution mode on CPU 1
[   29.999272] PCI: Enabling device 0000:00:04.0 (0000 -> 0002)
[   29.999276] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 23
[   29.999280] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   29.999285] PM: Writing back config space on device 0000:00:04.0 at offset f (was 1030100, writing 103010b)
[   29.999291] PM: Writing back config space on device 0000:00:04.0 at offset 4 (was 0, writing e5108000)
[   29.999295] PM: Writing back config space on device 0000:00:04.0 at offset 1 (was b00006, writing b00007)
[   30.010216] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [AUB2] -> GSI 22 (level, low) -> IRQ 22
[   30.010219] PCI: Setting latency timer of device 0000:00:04.1 to 64
[   30.010234] usb usb2: root hub lost power or was reset
[   30.010241] ehci_hcd 0000:00:04.1: debug port 1
[   30.010243] PCI: cache line size of 32 is not supported by device 0000:00:04.1
[   30.021244] PM: Writing back config space on device 0000:00:09.0 at offset 1 (was b00006, writing b00002)
[   30.021251] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 23
[   30.021255] PCI: Setting latency timer of device 0000:00:09.0 to 64
[   30.021274] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   30.021286] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   30.021299] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[   30.021310] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[   30.021319] PM: Writing back config space on device 0000:00:0e.0 at offset 1 (was b00403, writing b00407)
[   30.021329] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   30.021348] PM: Writing back config space on device 0000:00:0f.0 at offset 1 (was b00007, writing b00003)
[   30.021366] NVRM: RmPowerManagement: 5
[   30.166955] PM: Writing back config space on device 0000:01:07.0 at offset f (was 4020100, writing 402010a)
[   30.166966] PM: Writing back config space on device 0000:01:07.0 at offset 5 (was 0, writing e5000000)
[   30.166970] PM: Writing back config space on device 0000:01:07.0 at offset 4 (was 0, writing e5004000)
[   30.166973] PM: Writing back config space on device 0000:01:07.0 at offset 3 (was 0, writing 2008)
[   30.166977] PM: Writing back config space on device 0000:01:07.0 at offset 1 (was 2100000, writing 2100006)
[   30.224505] serial 00:08: activated
[   30.276707] usb usb1: root hub lost power or was reset
[   30.325606] ata1: SATA link down (SStatus 0 SControl 300)
[   30.325616] ata4: SATA link down (SStatus 0 SControl 300)
[   30.527227] sd 1:0:0:0: [sda] Starting disk
[   30.629024] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   30.629052] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   30.637718] ata2.00: configured for UDMA/133
[   30.641379] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   30.641389] sd 1:0:0:0: [sda] Write Protect is off
[   30.641391] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   30.641405] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   30.641453] PM: Image restored successfully.
[   30.673355] Restarting tasks ... <6>usb 1-2: USB disconnect, address 2
[   30.674179] done.
[   30.675193] swsusp: Basic memory bitmaps freed
[   30.932285] ata3.00: configured for UDMA/100
[   31.206916] usb 1-2: new low speed USB device using ohci_hcd and address 3
[   31.398590] usb 1-2: configuration #1 chosen from 1 choice
[   31.412711] input: BTC USB Multimedia Cordless Kit   as /class/input/input5
[   31.419523] input: USB HID v1.00 Keyboard [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   31.432992] input: BTC USB Multimedia Cordless Kit   as /class/input/input6
[   31.442602] input,hiddev96: USB HID v1.00 Mouse [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   34.856002] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[   34.856026] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
[   34.856031] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   35.367877] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1a:4d:59:db:59
[   35.367883] forcedeth 0000:00:0f.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[   35.579445] eth0: no link during initialization.
[   35.583296] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   35.583299] bridge-eth0: enabling the bridge
[   35.583302] bridge-eth0: up
[   36.542758] eth0: link up.
[   36.545859] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   38.064439] input: Power Button (FF) as /class/input/input7
[   38.071816] ACPI: Power Button (FF) [PWRF]
[   38.071859] input: Power Button (CM) as /class/input/input8
[   38.083678] ACPI: Power Button (CM) [PWRB]
[   55.662103] eth0: no IPv6 routers present
[  376.174004]  CIFS VFS: No response for cmd 50 mid 31713
[ 7786.218334] npviewer.bin[24121]: segfault at 1 rip f7a7baf7 rsp ffe3bf44 error 4
[24893.254516] npviewer.bin[29513]: segfault at f77c85de rip f7aaa0ed rsp ffb90540 error 7
[24893.254519] npviewer.bin[29530]: segfault at f77c85de rip f7aaa0ed rsp f5b70d80 error 7
[25078.778898] npviewer.bin[29705]: segfault at f77c8599 rip f7aaa0ed rsp f5b70d80 error 7
[25078.778902] npviewer.bin[29688]: segfault at f77c8599 rip f7aaa0ed rsp ffa003b0 error 7
[25478.360380] npviewer.bin[30026]: segfault at f77505c9 rip f7a51745 rsp f52f7cc0 error 7
[25478.360383] npviewer.bin[29991]: segfault at f77505c9 rip f7a51745 rsp ff89c180 error 7
[27243.199530] sr0: CDROM not ready yet.
[27245.238219] sr0: CDROM not ready yet.
[27247.255134] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27248.256161] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27249.256204] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27250.256268] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27251.256385] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27252.256483] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27253.256531] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27254.256633] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27255.256725] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27256.256822] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27257.256873] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27258.256958] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27259.257047] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27260.257133] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27261.257244] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27262.257314] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27263.257382] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27264.257498] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27265.257582] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27266.257640] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27267.257755] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27268.257843] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27269.257895] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27270.258008] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27271.258101] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27272.258152] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27273.258251] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27274.258347] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27275.258413] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27276.258520] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27277.258618] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27278.258668] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27279.258971] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27280.157397] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27280.258904] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27281.258931] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27282.259034] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27283.259094] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27284.259180] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27285.259307] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27286.259386] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27287.259480] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27288.259525] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27289.259612] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27290.259940] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27291.259821] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27292.259898] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27293.296230] sr0: CDROM not ready yet.
[27295.334928] sr0: CDROM not ready yet.
[27297.373590] sr0: CDROM not ready yet.
[27299.412293] sr0: CDROM not ready yet.
[27301.450981] sr0: CDROM not ready yet.
[27304.623771] end_request: I/O error, dev sr0, sector 0
[27304.623776] Buffer I/O error on device sr0, logical block 0
[27304.623780] Buffer I/O error on device sr0, logical block 1
[27304.623783] Buffer I/O error on device sr0, logical block 2
[27304.623785] Buffer I/O error on device sr0, logical block 3
[27304.623787] Buffer I/O error on device sr0, logical block 4
[27304.623790] Buffer I/O error on device sr0, logical block 5
[27304.623792] Buffer I/O error on device sr0, logical block 6
[27304.623795] Buffer I/O error on device sr0, logical block 7
[27304.625137] end_request: I/O error, dev sr0, sector 0
[27304.625140] Buffer I/O error on device sr0, logical block 0
[27304.626513] end_request: I/O error, dev sr0, sector 4
[27304.626516] Buffer I/O error on device sr0, logical block 1
[27304.627883] end_request: I/O error, dev sr0, sector 0
[27304.629261] end_request: I/O error, dev sr0, sector 4
[27304.630634] end_request: I/O error, dev sr0, sector 0
[27304.632012] end_request: I/O error, dev sr0, sector 4
[27304.633384] end_request: I/O error, dev sr0, sector 0
[27304.634763] end_request: I/O error, dev sr0, sector 4
[27304.636136] end_request: I/O error, dev sr0, sector 0
[27304.638103] end_request: I/O error, dev sr0, sector 4
[27304.639478] end_request: I/O error, dev sr0, sector 0
[27304.640856] end_request: I/O error, dev sr0, sector 4
[27304.642230] end_request: I/O error, dev sr0, sector 0
[27304.643610] end_request: I/O error, dev sr0, sector 4
[27304.644983] end_request: I/O error, dev sr0, sector 0
[27304.646362] end_request: I/O error, dev sr0, sector 4
[27304.647736] end_request: I/O error, dev sr0, sector 0
[27304.649115] end_request: I/O error, dev sr0, sector 4
[27304.650489] end_request: I/O error, dev sr0, sector 0
[27304.651866] end_request: I/O error, dev sr0, sector 4
[27304.653242] end_request: I/O error, dev sr0, sector 0
[27304.654621] end_request: I/O error, dev sr0, sector 4
[27304.655994] end_request: I/O error, dev sr0, sector 0
[27304.657373] end_request: I/O error, dev sr0, sector 4
[27304.659338] end_request: I/O error, dev sr0, sector 0
[27304.660715] end_request: I/O error, dev sr0, sector 4
[27304.662091] end_request: I/O error, dev sr0, sector 0
[27304.663468] end_request: I/O error, dev sr0, sector 4
[27304.664844] end_request: I/O error, dev sr0, sector 0
[27304.666220] end_request: I/O error, dev sr0, sector 4
[27304.667597] end_request: I/O error, dev sr0, sector 0
[27304.668973] end_request: I/O error, dev sr0, sector 4
[27304.670350] end_request: I/O error, dev sr0, sector 0
[27304.671727] end_request: I/O error, dev sr0, sector 4
[27304.673103] end_request: I/O error, dev sr0, sector 0
[27304.674479] end_request: I/O error, dev sr0, sector 4
[27304.675855] end_request: I/O error, dev sr0, sector 0
[27304.677232] end_request: I/O error, dev sr0, sector 4
[27304.678608] end_request: I/O error, dev sr0, sector 0
[27304.680574] end_request: I/O error, dev sr0, sector 4
[27304.681948] end_request: I/O error, dev sr0, sector 0
[27304.683327] end_request: I/O error, dev sr0, sector 4
[27304.684701] end_request: I/O error, dev sr0, sector 0
[27304.686080] end_request: I/O error, dev sr0, sector 4
[27304.687455] end_request: I/O error, dev sr0, sector 0
[27304.688832] end_request: I/O error, dev sr0, sector 4
[27304.690206] end_request: I/O error, dev sr0, sector 0
[27304.691586] end_request: I/O error, dev sr0, sector 4
[27304.692959] end_request: I/O error, dev sr0, sector 0
[27304.694338] end_request: I/O error, dev sr0, sector 4
[27304.695712] end_request: I/O error, dev sr0, sector 0
[27304.697091] end_request: I/O error, dev sr0, sector 4
[27304.698465] end_request: I/O error, dev sr0, sector 0
[27304.699844] end_request: I/O error, dev sr0, sector 4
[27304.827167] end_request: I/O error, dev sr0, sector 0
[27304.829133] end_request: I/O error, dev sr0, sector 4
[27304.830507] end_request: I/O error, dev sr0, sector 0
[27304.831886] end_request: I/O error, dev sr0, sector 4
[27633.478052] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[27633.478061] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[27633.478062]          cdb 1b 00 00 00 02 00 00 00  00 00 00 00 00 00 00 00
[27633.478063]          res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[27633.478066] ata3.00: status: { DRDY }
[27633.478073] ata3: hard resetting link
[27634.088877] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[27634.480533] ata3.00: configured for UDMA/100
[27634.480543] ata3: EH complete
[27662.800986] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[27672.782175] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[55128.897815] bridge-eth0: disabling the bridge
[55128.900941] bridge-eth0: down
[55128.996792] ACPI: PCI interrupt for device 0000:00:0f.0 disabled
[55130.517763] PM: suspend-to-disk mode set to 'shutdown'
[55130.517916] swsusp: Marking nosave pages: 000000000009e000 - 0000000000100000
[55130.517921] swsusp: Marking nosave pages: 0000000077000000 - 000000007f000000
[55130.518639] swsusp: Basic memory bitmaps created
[55130.518641] Syncing filesystems ... done.
[55130.540753] Freezing user space processes ... (elapsed 0.00 seconds) done.
[55130.541101] Freezing remaining freezable tasks ... (elapsed 6.93 seconds) done.
[55137.459562] Shrinking memory...  \b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\bdone (191473 pages freed)
[55139.814898] Freed 765892 kbytes in 2.35 seconds (325.91 MB/s)
[55139.814900] Suspending console(s)
[55140.016416] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[55140.016604] ACPI handle has no context!
[55140.016827] serial 00:08: disabled
[55140.016864] ACPI handle has no context!
[55140.027404] NVRM: RmPowerManagement: 3
[55140.220036] ACPI: PCI interrupt for device 0000:00:09.0 disabled
[55140.231095] ACPI: PCI interrupt for device 0000:00:04.1 disabled
[55140.242005] ACPI: PCI interrupt for device 0000:00:04.0 disabled
[55140.253405] Disabling non-boot CPUs ...
[55140.358760] CPU 1 is now offline
[55140.358763] SMP alternatives: switching to UP code
[55140.359889] CPU1 is down
[55140.360028] swsusp: critical section: 
[55140.399385] swsusp: Need to copy 124487 pages
[55140.399388] swsusp: Normal pages needed: 124487 + 1024 + 38, available pages: 366397
[   29.948252] Enabling non-boot CPUs ...
[   29.950611] SMP alternatives: switching to SMP code
[   29.951364] Booting processor 1/2 APIC 0x1
[   29.961711] Initializing CPU#1
[   30.021410] Calibrating delay using timer specific routine.. 4666.90 BogoMIPS (lpj=2333450)
[   30.021415] CPU: L1 I cache: 32K, L1 D cache: 32K
[   30.021417] CPU: L2 cache: 4096K
[   30.021418] CPU: Physical Processor ID: 0
[   30.021419] CPU: Processor Core ID: 1
[   30.021816] Intel(R) Core(TM)2 Duo CPU     E6550  @ 2.33GHz stepping 0b
[   30.021856] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   30.042093] CPU1 is up
[   30.042837] Switched to high resolution mode on CPU 1
[   30.053386] PCI: Enabling device 0000:00:04.0 (0000 -> 0002)
[   30.053390] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 23
[   30.053394] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   30.053398] PM: Writing back config space on device 0000:00:04.0 at offset f (was 1030100, writing 103010b)
[   30.053405] PM: Writing back config space on device 0000:00:04.0 at offset 4 (was 0, writing e5108000)
[   30.053408] PM: Writing back config space on device 0000:00:04.0 at offset 1 (was b00006, writing b00007)
[   30.064379] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [AUB2] -> GSI 22 (level, low) -> IRQ 22
[   30.064383] PCI: Setting latency timer of device 0000:00:04.1 to 64
[   30.064398] usb usb2: root hub lost power or was reset
[   30.064405] ehci_hcd 0000:00:04.1: debug port 1
[   30.064407] PCI: cache line size of 32 is not supported by device 0000:00:04.1
[   30.075381] PM: Writing back config space on device 0000:00:09.0 at offset 1 (was b00006, writing b00002)
[   30.075389] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 23
[   30.075393] PCI: Setting latency timer of device 0000:00:09.0 to 64
[   30.075412] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   30.075424] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   30.075436] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[   30.075448] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[   30.075457] PM: Writing back config space on device 0000:00:0e.0 at offset 1 (was b00403, writing b00407)
[   30.075466] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   30.075486] PM: Writing back config space on device 0000:00:0f.0 at offset 1 (was b00007, writing b00003)
[   30.075504] NVRM: RmPowerManagement: 5
[   30.221078] PM: Writing back config space on device 0000:01:07.0 at offset f (was 4020100, writing 402010a)
[   30.221090] PM: Writing back config space on device 0000:01:07.0 at offset 5 (was 0, writing e5000000)
[   30.221093] PM: Writing back config space on device 0000:01:07.0 at offset 4 (was 0, writing e5004000)
[   30.221096] PM: Writing back config space on device 0000:01:07.0 at offset 3 (was 0, writing 2008)
[   30.221101] PM: Writing back config space on device 0000:01:07.0 at offset 1 (was 2100000, writing 2100006)
[   30.278639] serial 00:08: activated
[   30.330833] usb usb1: root hub lost power or was reset
[   30.379734] ata4: SATA link down (SStatus 0 SControl 300)
[   30.379745] ata1: SATA link down (SStatus 0 SControl 300)
[   30.582345] sd 1:0:0:0: [sda] Starting disk
[   30.683149] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   30.683165] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   30.689050] ata2.00: configured for UDMA/133
[   30.692716] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   30.692726] sd 1:0:0:0: [sda] Write Protect is off
[   30.692728] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   30.692742] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   30.692796] PM: Image restored successfully.
[   30.726394] Restarting tasks ... <6>usb 1-2: USB disconnect, address 3
[   30.734505] done.
[   30.736236] swsusp: Basic memory bitmaps freed
[   30.986425] ata3.00: configured for UDMA/100
[   31.267285] usb 1-2: new low speed USB device using ohci_hcd and address 4
[   31.458759] usb 1-2: configuration #1 chosen from 1 choice
[   31.472803] input: BTC USB Multimedia Cordless Kit   as /class/input/input9
[   31.489635] input: USB HID v1.00 Keyboard [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   31.503044] input: BTC USB Multimedia Cordless Kit   as /class/input/input10
[   31.526826] input,hiddev96: USB HID v1.00 Mouse [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   32.472201] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[   32.472225] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
[   32.472229] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   32.984647] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1a:4d:59:db:59
[   32.984652] forcedeth 0000:00:0f.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[   33.016838] eth0: no link during initialization.
[   33.020688] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   33.020691] bridge-eth0: enabling the bridge
[   33.020695] bridge-eth0: up
[   34.347099] eth0: link up.
[   34.350984] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.524674] input: Power Button (FF) as /class/input/input11
[   34.536793] ACPI: Power Button (FF) [PWRF]
[   34.536835] input: Power Button (CM) as /class/input/input12
[   34.548780] ACPI: Power Button (CM) [PWRB]
[   53.026629] eth0: no IPv6 routers present
[  220.887434]  CIFS VFS: No response for cmd 50 mid 50128
[ 1646.490993] bridge-eth0: disabling the bridge
[ 1646.496328] bridge-eth0: down
[ 1646.590560] ACPI: PCI interrupt for device 0000:00:0f.0 disabled
[ 1648.079695] PM: suspend-to-disk mode set to 'shutdown'
[ 1648.079831] swsusp: Marking nosave pages: 000000000009e000 - 0000000000100000
[ 1648.079835] swsusp: Marking nosave pages: 0000000077000000 - 000000007f000000
[ 1648.080556] swsusp: Basic memory bitmaps created
[ 1648.080557] Syncing filesystems ... done.
[ 1648.102787] Freezing user space processes ... (elapsed 0.00 seconds) done.
[ 1648.103104] Freezing remaining freezable tasks ... (elapsed 7.72 seconds) done.
[ 1655.809473] Shrinking memory...  \b-\b\\b|\b/\b-\b\\b|\b/\bdone (112983 pages freed)
[ 1657.182523] Freed 451932 kbytes in 1.37 seconds (329.87 MB/s)
[ 1657.182525] Suspending console(s)
[ 1657.384459] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[ 1657.384646] ACPI handle has no context!
[ 1657.384869] serial 00:08: disabled
[ 1657.384905] ACPI handle has no context!
[ 1657.395447] NVRM: RmPowerManagement: 3
[ 1657.588079] ACPI: PCI interrupt for device 0000:00:09.0 disabled
[ 1657.599137] ACPI: PCI interrupt for device 0000:00:04.1 disabled
[ 1657.610048] ACPI: PCI interrupt for device 0000:00:04.0 disabled
[ 1657.621449] Disabling non-boot CPUs ...
[ 1657.726803] CPU 1 is now offline
[ 1657.726806] SMP alternatives: switching to UP code
[ 1657.727888] CPU1 is down
[ 1657.728027] swsusp: critical section: 
[ 1657.766803] swsusp: Need to copy 108235 pages
[ 1657.766805] swsusp: Normal pages needed: 108235 + 1024 + 38, available pages: 382652
[   29.914763] Enabling non-boot CPUs ...
[   29.917152] SMP alternatives: switching to SMP code
[   29.917906] Booting processor 1/2 APIC 0x1
[   29.928253] Initializing CPU#1
[   29.987958] Calibrating delay using timer specific routine.. 4666.90 BogoMIPS (lpj=2333454)
[   29.987963] CPU: L1 I cache: 32K, L1 D cache: 32K
[   29.987964] CPU: L2 cache: 4096K
[   29.987966] CPU: Physical Processor ID: 0
[   29.987967] CPU: Processor Core ID: 1
[   29.988364] Intel(R) Core(TM)2 Duo CPU     E6550  @ 2.33GHz stepping 0b
[   29.988401] checking TSC synchronization [CPU#0 -> CPU#1]:
[   30.008365] Measured 124887420 cycles TSC warp between CPUs, turning off TSC clock.
[   30.008367] Marking TSC unstable due to check_tsc_sync_source failed
[   30.008373] Time: hpet clocksource has been installed.
[   30.008640] CPU1 is up
[   30.009386] Switched to high resolution mode on CPU 1
[   30.019937] PCI: Enabling device 0000:00:04.0 (0000 -> 0002)
[   30.019940] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 23
[   30.019945] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   30.019949] PM: Writing back config space on device 0000:00:04.0 at offset f (was 1030100, writing 103010b)
[   30.019956] PM: Writing back config space on device 0000:00:04.0 at offset 4 (was 0, writing e5108000)
[   30.019959] PM: Writing back config space on device 0000:00:04.0 at offset 1 (was b00006, writing b00007)
[   30.030930] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [AUB2] -> GSI 22 (level, low) -> IRQ 22
[   30.030934] PCI: Setting latency timer of device 0000:00:04.1 to 64
[   30.030949] usb usb2: root hub lost power or was reset
[   30.030955] ehci_hcd 0000:00:04.1: debug port 1
[   30.030958] PCI: cache line size of 32 is not supported by device 0000:00:04.1
[   30.041931] PM: Writing back config space on device 0000:00:09.0 at offset 1 (was b00006, writing b00002)
[   30.041939] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 23
[   30.041943] PCI: Setting latency timer of device 0000:00:09.0 to 64
[   30.041962] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   30.041974] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   30.041987] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[   30.041999] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[   30.042008] PM: Writing back config space on device 0000:00:0e.0 at offset 1 (was b00403, writing b00407)
[   30.042017] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   30.042036] PM: Writing back config space on device 0000:00:0f.0 at offset 1 (was b00007, writing b00003)
[   30.042053] NVRM: RmPowerManagement: 5
[   30.188630] PM: Writing back config space on device 0000:01:07.0 at offset f (was 4020100, writing 402010a)
[   30.188641] PM: Writing back config space on device 0000:01:07.0 at offset 5 (was 0, writing e5000000)
[   30.188645] PM: Writing back config space on device 0000:01:07.0 at offset 4 (was 0, writing e5004000)
[   30.188648] PM: Writing back config space on device 0000:01:07.0 at offset 3 (was 0, writing 2008)
[   30.188652] PM: Writing back config space on device 0000:01:07.0 at offset 1 (was 2100000, writing 2100006)
[   30.246177] serial 00:08: activated
[   30.298368] usb usb1: root hub lost power or was reset
[   30.346268] ata1: SATA link down (SStatus 0 SControl 300)
[   30.346278] ata4: SATA link down (SStatus 0 SControl 300)
[   30.548877] sd 1:0:0:0: [sda] Starting disk
[   30.649680] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   30.649696] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   30.655668] ata2.00: configured for UDMA/133
[   30.659333] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   30.659343] sd 1:0:0:0: [sda] Write Protect is off
[   30.659345] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   30.659359] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   30.659412] PM: Image restored successfully.
[   30.690677] Restarting tasks ... <6>usb 1-2: USB disconnect, address 4
[   30.704037] done.
[   30.705800] swsusp: Basic memory bitmaps freed
[   30.952962] ata3.00: configured for UDMA/100
[   31.235561] usb 1-2: new low speed USB device using ohci_hcd and address 5
[   31.427288] usb 1-2: configuration #1 chosen from 1 choice
[   31.441373] input: BTC USB Multimedia Cordless Kit   as /class/input/input13
[   31.454178] input: USB HID v1.00 Keyboard [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   31.467652] input: BTC USB Multimedia Cordless Kit   as /class/input/input14
[   31.479133] input,hiddev96: USB HID v1.00 Mouse [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   33.523894] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[   33.523915] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
[   33.523920] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   34.036115] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1a:4d:59:db:59
[   34.036119] forcedeth 0000:00:0f.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[   34.069201] eth0: no link during initialization.
[   34.073098] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.073101] bridge-eth0: enabling the bridge
[   34.073105] bridge-eth0: up
[   35.094431] input: Power Button (FF) as /class/input/input15
[   35.107176] ACPI: Power Button (FF) [PWRF]
[   35.107220] input: Power Button (CM) as /class/input/input16
[   35.121716] ACPI: Power Button (CM) [PWRB]
[   35.419744] eth0: link up.
[   35.423325] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   50.564818] eth0: no IPv6 routers present
[  427.856088] printk: 56 messages suppressed.
[  427.856093] npviewer.bin[13266]: segfault at 34 rip f7b59950 rsp f5b67cb0 error 4
[ 5443.257675]  CIFS VFS: No response for cmd 50 mid 50170
[ 6515.010138] npviewer.bin[15888]: segfault at 44 rip 44 rsp fffd2bec error 14
[ 6696.476933] npviewer.bin[15998]: segfault at 18 rip f7aa511c rsp ffc2fdc0 error 4
[ 6722.940424] npviewer.bin[16077]: segfault at 30 rip f7a9b6fe rsp f5b437d0 error 4
[16391.542469] bridge-eth0: disabling the bridge
[16391.547739] bridge-eth0: down
[16391.630627] ACPI: PCI interrupt for device 0000:00:0f.0 disabled
[16393.062824] PM: suspend-to-disk mode set to 'shutdown'
[16393.062970] swsusp: Marking nosave pages: 000000000009e000 - 0000000000100000
[16393.062974] swsusp: Marking nosave pages: 0000000077000000 - 000000007f000000
[16393.063691] swsusp: Basic memory bitmaps created
[16393.063692] Syncing filesystems ... done.
[16393.100603] Freezing user space processes ... (elapsed 0.00 seconds) done.
[16393.100958] Freezing remaining freezable tasks ... (elapsed 2.88 seconds) done.
[16395.976265] Shrinking memory...  \b-\b\\b|\b/\b-\b\\b|\b/\bdone (106375 pages freed)
[16397.160402] Freed 425500 kbytes in 1.18 seconds (360.59 MB/s)
[16397.160404] Suspending console(s)
[16397.162312] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[16397.162515] ACPI handle has no context!
[16397.162712] serial 00:08: disabled
[16397.162758] ACPI handle has no context!
[16397.173754] NVRM: RmPowerManagement: 3
[16397.367366] ACPI: PCI interrupt for device 0000:00:09.0 disabled
[16397.378423] ACPI: PCI interrupt for device 0000:00:04.1 disabled
[16397.389333] ACPI: PCI interrupt for device 0000:00:04.0 disabled
[16397.400733] Disabling non-boot CPUs ...
[16397.506099] CPU 1 is now offline
[16397.506102] SMP alternatives: switching to UP code
[16397.507182] CPU1 is down
[16397.507323] swsusp: critical section: 
[16397.545704] swsusp: Need to copy 124847 pages
[16397.545707] swsusp: Normal pages needed: 124847 + 1024 + 38, available pages: 366040
[   30.132788] Enabling non-boot CPUs ...
[   30.135168] SMP alternatives: switching to SMP code
[   30.135921] Booting processor 1/2 APIC 0x1
[   30.146266] Initializing CPU#1
[   30.205966] Calibrating delay using timer specific routine.. 4666.91 BogoMIPS (lpj=2333456)
[   30.205971] CPU: L1 I cache: 32K, L1 D cache: 32K
[   30.205972] CPU: L2 cache: 4096K
[   30.205974] CPU: Physical Processor ID: 0
[   30.205975] CPU: Processor Core ID: 1
[   30.206372] Intel(R) Core(TM)2 Duo CPU     E6550  @ 2.33GHz stepping 0b
[   30.206651] CPU1 is up
[   30.207393] Switched to high resolution mode on CPU 1
[   30.217967] PCI: Enabling device 0000:00:04.0 (0000 -> 0002)
[   30.217971] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 23
[   30.217976] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   30.217980] PM: Writing back config space on device 0000:00:04.0 at offset f (was 1030100, writing 103010b)
[   30.217987] PM: Writing back config space on device 0000:00:04.0 at offset 4 (was 0, writing e5108000)
[   30.217990] PM: Writing back config space on device 0000:00:04.0 at offset 1 (was b00006, writing b00007)
[   30.228940] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [AUB2] -> GSI 22 (level, low) -> IRQ 22
[   30.228944] PCI: Setting latency timer of device 0000:00:04.1 to 64
[   30.228959] usb usb2: root hub lost power or was reset
[   30.228966] ehci_hcd 0000:00:04.1: debug port 1
[   30.228968] PCI: cache line size of 32 is not supported by device 0000:00:04.1
[   30.239979] PM: Writing back config space on device 0000:00:09.0 at offset 1 (was b00006, writing b00002)
[   30.239987] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 23
[   30.239991] PCI: Setting latency timer of device 0000:00:09.0 to 64
[   30.240010] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   30.240022] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   30.240035] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[   30.240047] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[   30.240056] PM: Writing back config space on device 0000:00:0e.0 at offset 1 (was b00403, writing b00407)
[   30.240066] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   30.240085] PM: Writing back config space on device 0000:00:0f.0 at offset 1 (was b00007, writing b00003)
[   30.240107] NVRM: RmPowerManagement: 5
[   30.383657] PM: Writing back config space on device 0000:01:07.0 at offset f (was 4020100, writing 402010a)
[   30.383668] PM: Writing back config space on device 0000:01:07.0 at offset 5 (was 0, writing e5000000)
[   30.383672] PM: Writing back config space on device 0000:01:07.0 at offset 4 (was 0, writing e5004000)
[   30.383675] PM: Writing back config space on device 0000:01:07.0 at offset 3 (was 0, writing 2008)
[   30.383679] PM: Writing back config space on device 0000:01:07.0 at offset 1 (was 2100000, writing 2100006)
[   30.441236] serial 00:08: activated
[   30.493430] usb usb1: root hub lost power or was reset
[   30.544332] ata1: SATA link down (SStatus 0 SControl 300)
[   30.544342] ata4: SATA link down (SStatus 0 SControl 300)
[   30.743949] sd 1:0:0:0: [sda] Starting disk
[   30.847753] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   30.847781] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   30.861239] ata2.00: configured for UDMA/133
[   30.864865] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   30.864875] sd 1:0:0:0: [sda] Write Protect is off
[   30.864877] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   30.864890] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   30.864928] PM: Image restored successfully.
[   30.895764] Restarting tasks ... <6>usb 1-2: USB disconnect, address 5
[   30.910113] done.
[   30.911828] swsusp: Basic memory bitmaps freed
[   31.151023] ata3.00: configured for UDMA/100
[   31.442611] usb 1-2: new low speed USB device using ohci_hcd and address 6
[   31.634295] usb 1-2: configuration #1 chosen from 1 choice
[   31.648402] input: BTC USB Multimedia Cordless Kit   as /class/input/input17
[   31.657215] input: USB HID v1.00 Keyboard [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   31.670699] input: BTC USB Multimedia Cordless Kit   as /class/input/input18
[   31.682189] input,hiddev96: USB HID v1.00 Mouse [BTC USB Multimedia Cordless Kit  ] on usb-0000:00:04.0-2
[   32.380567] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[   32.380594] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
[   32.380599] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   32.892756] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1a:4d:59:db:59
[   32.892760] forcedeth 0000:00:0f.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[   32.924801] eth0: no link during initialization.
[   32.928727] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   32.928730] bridge-eth0: enabling the bridge
[   32.928734] bridge-eth0: up
[   34.266185] eth0: link up.
[   34.270076] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.271522] input: Power Button (FF) as /class/input/input19
[   34.284207] ACPI: Power Button (FF) [PWRF]
[   34.284251] input: Power Button (CM) as /class/input/input20
[   34.294420] ACPI: Power Button (CM) [PWRB]
[   49.247535] eth0: no IPv6 routers present
[  373.235997]  CIFS VFS: No response for cmd 50 mid 54293
[  500.725653] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[  500.725660] ata2.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 0
[  500.725661]          res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[  500.725664] ata2.00: status: { DRDY }
[  500.725670] ata2: hard resetting link
[  501.333485] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  501.342713] ata2.00: configured for UDMA/133
[  501.342721] ata2: EH complete
[  501.342866] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[  501.342982] sd 1:0:0:0: [sda] Write Protect is off
[  501.342985] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  501.343181] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  507.331011] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[  507.331019] ata2.00: cmd b0/d1:01:01:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[  507.331021]          res 40/00:01:b4:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[  507.331023] ata2.00: status: { DRDY }
[  507.331029] ata2: hard resetting link
[  507.938846] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  507.952183] ata2.00: configured for UDMA/133
[  507.952191] ata2: EH complete
[  507.952423] sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[  507.952511] sd 1:0:0:0: [sda] Write Protect is off
[  507.952514] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  507.952750] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-04-15  6:21       ` Tvrtko A. Ursulin
@ 2008-05-14  5:44         ` Tejun Heo
  2008-05-14  6:58           ` Tvrtko A. Ursulin
  0 siblings, 1 reply; 8+ messages in thread
From: Tejun Heo @ 2008-05-14  5:44 UTC (permalink / raw)
  To: Tvrtko A. Ursulin; +Cc: linux-ide, linux-kernel, Bruce Allen

Tvrtko A. Ursulin wrote:
> On Tuesday 15 April 2008 04:10:57 Tejun Heo wrote:
>> Tvrtko A. Ursulin wrote:
>>> On Sunday 13 April 2008 04:11:15 Tejun Heo wrote:
>>>> Is auto spindown configured for the drive?
>>> I don't think so - it's a 3.5" drive with no special PM features - but
>>> how to tell?
>> Hmm... Can you please post the result of "smartctl --version" and
>> "smartctl -a > out 2>&1" and dmesg after the smartctl command?
> 
> Yep, pasted and attached below. dmesg is 67k, hope list is happy with that.

Thanks for the data.  Nothing really stands out tho.  It looks like the 
drive just doesn't like SMART commands 0xda and 0xd1.  0xda being a 
mandatory non-data command, it failing due to driver problem is unlikely.

Can you please post the result of "hdparm -I /dev/sda" and "lspci -nn"?

Bruce, WDC WD3200AAKS-00VYA0, 12.01B02 is timing out SMART commands 0xda 
and 0xd1 and the reported data seems all wrong.  Does it ring a bell? 
The original thread can be read from the following URL.

   http://thread.gmane.org/gmane.linux.ide/30459

Thanks.

-- 
tejun

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-05-14  5:44         ` Tejun Heo
@ 2008-05-14  6:58           ` Tvrtko A. Ursulin
  2008-05-14  7:29             ` Tejun Heo
  0 siblings, 1 reply; 8+ messages in thread
From: Tvrtko A. Ursulin @ 2008-05-14  6:58 UTC (permalink / raw)
  To: Tejun Heo; +Cc: linux-ide, linux-kernel, Bruce Allen

On Wednesday 14 May 2008 06:44:12 Tejun Heo wrote:
> Tvrtko A. Ursulin wrote:
> > On Tuesday 15 April 2008 04:10:57 Tejun Heo wrote:
> >> Tvrtko A. Ursulin wrote:
> >>> On Sunday 13 April 2008 04:11:15 Tejun Heo wrote:
> >>>> Is auto spindown configured for the drive?
> >>>
> >>> I don't think so - it's a 3.5" drive with no special PM features - but
> >>> how to tell?
> >>
> >> Hmm... Can you please post the result of "smartctl --version" and
> >> "smartctl -a > out 2>&1" and dmesg after the smartctl command?
> >
> > Yep, pasted and attached below. dmesg is 67k, hope list is happy with
> > that.
>
> Thanks for the data.  Nothing really stands out tho.  It looks like the
> drive just doesn't like SMART commands 0xda and 0xd1.  0xda being a
> mandatory non-data command, it failing due to driver problem is unlikely.
>
> Can you please post the result of "hdparm -I /dev/sda" and "lspci -nn"?

Of course:

root@sol:~# hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media
        Model Number:       WDC WD3200AAKS-00VYA0
        Serial Number:      WD-WCARW0059893
        Firmware Revision:  12.01B02
Standards:
        Supported: 8 7 6 5
        Likely used: 8
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors:  625142448
        device size with M = 1024*1024:      305245 MBytes
        device size with M = 1000*1000:      320072 MBytes (320 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 32
        Standby timer values: spec'd by Standard, with device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 0
        Recommended acoustic management value: 128, current value: 254
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
                SMART feature set
                Security Mode feature set
           *    Power Management feature set
           *    Write cache
           *    Look-ahead
           *    Host Protected Area feature set
           *    WRITE_BUFFER command
           *    READ_BUFFER command
           *    NOP cmd
           *    DOWNLOAD_MICROCODE
                Power-Up In Standby feature set
           *    SET_FEATURES required to spinup after power up
                SET_MAX security extension
                Automatic Acoustic Management feature set
           *    48-bit Address feature set
           *    Device Configuration Overlay feature set
           *    Mandatory FLUSH_CACHE
           *    FLUSH_CACHE_EXT
           *    SMART error logging
           *    SMART self-test
           *    General Purpose Logging feature set
           *    64-bit World wide name
           *    Segmented DOWNLOAD_MICROCODE
           *    SATA-I signaling speed (1.5Gb/s)
           *    SATA-II signaling speed (3.0Gb/s)
           *    Native Command Queueing (NCQ)
           *    Host-initiated interface power management
           *    Phy event counters
                DMA Setup Auto-Activate optimization
           *    Software settings preservation
           *    SMART Command Transport (SCT) feature set
           *    SCT Long Sector Access (AC1)
           *    SCT LBA Segment Access (AC2)
           *    SCT Error Recovery Control (AC3)
           *    SCT Features Control (AC4)
           *    SCT Data Tables (AC5)
                unknown 206[12] (vendor specific)
                unknown 206[13] (vendor specific)
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
                supported: enhanced erase
        88min for SECURITY ERASE UNIT. 88min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50014ee1485655
        NAA             : 5
        IEEE OUI        : 14ee
        Unique ID       : 1485655
Checksum: correct
root@sol:~# lspci -nn
00:00.0 Host bridge [0600]: nVidia Corporation Unknown device [10de:07c1] (rev a2)
00:00.1 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07cb] (rev a2)
00:01.0 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07cd] (rev a1)
00:01.1 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07ce] (rev a1)
00:01.2 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07cf] (rev a1)
00:01.3 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07d0] (rev a1)
00:01.4 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07d1] (rev a1)
00:01.5 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07d2] (rev a1)
00:01.6 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07d3] (rev a1)
00:02.0 RAM memory [0500]: nVidia Corporation nForce 630i memory controller [10de:07d6] (rev a1)
00:03.0 ISA bridge [0601]: nVidia Corporation Unknown device [10de:07d7] (rev a2)
00:03.1 SMBus [0c05]: nVidia Corporation Unknown device [10de:07d8] (rev a1)
00:03.2 RAM memory [0500]: nVidia Corporation Unknown device [10de:07d9] (rev a1)
00:03.4 RAM memory [0500]: nVidia Corporation Unknown device [10de:07c8] (rev a1)
00:04.0 USB Controller [0c03]: nVidia Corporation GeForce 7100/nForce 630i [10de:07fe] (rev a1)
00:04.1 USB Controller [0c03]: nVidia Corporation GeForce 7100/nForce 630i [10de:056a] (rev a1)
00:08.0 IDE interface [0101]: nVidia Corporation Unknown device [10de:056c] (rev a1)
00:09.0 Audio device [0403]: nVidia Corporation MCP73 High Definition Audio [10de:07fc] (rev a1)
00:0a.0 PCI bridge [0604]: nVidia Corporation Unknown device [10de:056d] (rev a1)
00:0b.0 PCI bridge [0604]: nVidia Corporation Unknown device [10de:056e] (rev a1)
00:0c.0 PCI bridge [0604]: nVidia Corporation Unknown device [10de:056f] (rev a1)
00:0d.0 PCI bridge [0604]: nVidia Corporation Unknown device [10de:056f] (rev a1)
00:0e.0 SATA controller [0106]: nVidia Corporation GeForce 7100/nForce 630i [10de:07f4] (rev a2)
00:0f.0 Ethernet controller [0200]: nVidia Corporation MCP73 Ethernet [10de:07dc] (rev a2)
00:10.0 VGA compatible controller [0300]: nVidia Corporation GeForce 7100/nForce 630i [10de:07e1] (rev a2)
01:07.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024]

Tvrtko


^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI
  2008-05-14  6:58           ` Tvrtko A. Ursulin
@ 2008-05-14  7:29             ` Tejun Heo
  0 siblings, 0 replies; 8+ messages in thread
From: Tejun Heo @ 2008-05-14  7:29 UTC (permalink / raw)
  To: Tvrtko A. Ursulin; +Cc: linux-ide, linux-kernel, Bruce Allen

Tvrtko A. Ursulin wrote:
> On Wednesday 14 May 2008 06:44:12 Tejun Heo wrote:
>> Tvrtko A. Ursulin wrote:
>>> On Tuesday 15 April 2008 04:10:57 Tejun Heo wrote:
>>>> Tvrtko A. Ursulin wrote:
>>>>> On Sunday 13 April 2008 04:11:15 Tejun Heo wrote:
>>>>>> Is auto spindown configured for the drive?
>>>>> I don't think so - it's a 3.5" drive with no special PM features - but
>>>>> how to tell?
>>>> Hmm... Can you please post the result of "smartctl --version" and
>>>> "smartctl -a > out 2>&1" and dmesg after the smartctl command?
>>> Yep, pasted and attached below. dmesg is 67k, hope list is happy with
>>> that.
>> Thanks for the data.  Nothing really stands out tho.  It looks like the
>> drive just doesn't like SMART commands 0xda and 0xd1.  0xda being a
>> mandatory non-data command, it failing due to driver problem is unlikely.
>>
>> Can you please post the result of "hdparm -I /dev/sda" and "lspci -nn"?
> 
> Of course:
> 
> root@sol:~# hdparm -I /dev/sda
> 
> /dev/sda:
> 
> ATA device, with non-removable media
>         Model Number:       WDC WD3200AAKS-00VYA0
>         Serial Number:      WD-WCARW0059893
>         Firmware Revision:  12.01B02

> 00:0e.0 SATA controller [0106]: nVidia Corporation GeForce 7100/nForce 630i [10de:07f4] (rev a2)

Hmmm.. WD3200 w/ nv ahci.  WD3200 having trouble with smart commands is 
unlikely.  Is it possible for you try different drive on the controller 
and see whether smartctl works on it?

Thanks.

-- 
tejun

^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2008-05-14  7:29 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-04-09 20:30 libata errors with smartctl on 2.6.24, WD3200AAKS and nVidia AHCI Tvrtko A. Ursulin
2008-04-13  3:11 ` Tejun Heo
2008-04-13  7:34   ` Tvrtko A. Ursulin
2008-04-15  3:10     ` Tejun Heo
2008-04-15  6:21       ` Tvrtko A. Ursulin
2008-05-14  5:44         ` Tejun Heo
2008-05-14  6:58           ` Tvrtko A. Ursulin
2008-05-14  7:29             ` Tejun Heo

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).