LKML Archive on lore.kernel.org help / color / mirror / Atom feed
From: Sebastian Andrzej Siewior <bigeasy@linutronix.de> To: Bryan Wu <cooloney@kernel.org> Cc: linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org, Michael Hennerich <michael.hennerich@analog.com> Subject: Re: [PATCH] USB/ISP1760: Add support for the generic platfrom device centralized driver model Date: Thu, 6 Nov 2008 18:57:05 +0100 [thread overview] Message-ID: <20081106175705.GA4687@www.tglx.de> (raw) In-Reply-To: <1225963549-9892-1-git-send-email-cooloney@kernel.org> * Bryan Wu | 2008-11-06 17:25:49 [+0800]: >From: Michael Hennerich <michael.hennerich@analog.com> > >Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> >Signed-off-by: Bryan Wu <cooloney@kernel.org> >--- > drivers/usb/host/isp1760-if.c | 98 +++++++++++++++++++++++++++++++++++++++++ > 1 files changed, 98 insertions(+), 0 deletions(-) > >diff --git a/drivers/usb/host/isp1760-if.c b/drivers/usb/host/isp1760-if.c >index af849f5..dc16698 100644 >--- a/drivers/usb/host/isp1760-if.c >+++ b/drivers/usb/host/isp1760-if.c >@@ -3,6 +3,7 @@ > * Currently there is support for > * - OpenFirmware > * - PCI >+ * - PDEV (generic platform device centralized driver model) > * > * (c) 2007 Sebastian Siewior <bigeasy@linutronix.de> > * >@@ -23,6 +24,12 @@ > #include <linux/pci.h> > #endif > >+#if !defined(CONFIG_USB_ISP1760_OF) && !defined(CONFIG_USB_ISP1760_PCI) >+#define USB_ISP1760_PDEV Usually I would prefer to make it conditional on CONFIGU_USB_ISP1760_PDEV. But since http://marc.info/?l=linux-usb&m=122563596420156&w=2 I would prefer to have unconditional. Any reason why you only enable it PDEV if you have neiher PCI nor OF? >+#include <linux/platform_device.h> >+#include <linux/usb/isp1760.h> You can't include files which are not mainline >+#endif >+ > #ifdef CONFIG_USB_ISP1760_OF > static int of_isp1760_probe(struct of_device *dev, > const struct of_device_id *match) >@@ -286,12 +293,100 @@ static struct pci_driver isp1761_pci_driver = { > }; > #endif > >+#ifdef USB_ISP1760_PDEV >+static int __devinit >+isp1760_pdev_probe(struct platform_device *pdev) >+{ Please make it static int __devinit isp1760_pdev_probe(struct platform_device *pdev) >+ struct usb_hcd *hcd; >+ struct resource *addr; >+ int irq; >+ unsigned int devflags = 0; >+ struct isp1760_platform_data *priv = pdev->dev.platform_data; >+ >+ /* basic sanity checks first. board-specific init logic should >+ * have initialized these two resources and probably board >+ * specific platform_data. we don't probe for IRQs, and do only >+ * minimal sanity checking. >+ */ >+ >+ if (usb_disabled()) >+ return -ENODEV; >+ >+ if (pdev->num_resources < 2) >+ return -ENODEV; >+ >+ addr = platform_get_resource(pdev, IORESOURCE_MEM, 0); >+ irq = platform_get_irq(pdev, 0); >+ >+ if (!addr || irq < 0) >+ return -ENODEV; >+ >+ if (priv) { >+ if (priv->is_isp1761) >+ devflags |= ISP1760_FLAG_ISP1761; >+ if (priv->port1_disable) >+ devflags |= ISP1760_FLAG_PORT1_DIS; >+ if (priv->bus_width_16) >+ devflags |= ISP1760_FLAG_BUS_WIDTH_16; >+ if (priv->port1_otg) >+ devflags |= ISP1760_FLAG_OTG_EN; >+ if (priv->analog_oc) >+ devflags |= ISP1760_FLAG_ANALOG_OC; >+ if (priv->dack_polarity_high) >+ devflags |= ISP1760_FLAG_DACK_POL_HIGH; >+ if (priv->dreq_polarity_high) >+ devflags |= ISP1760_FLAG_DREQ_POL_HIGH; >+ } >+ >+ hcd = isp1760_register(addr->start, resource_size(addr), irq, >+ IRQF_DISABLED | IRQF_SHARED | IRQF_TRIGGER_FALLING, This won't work. The chip itself is configured as level, active low. You have to make sure the chip is configured as edge as well. >+ &pdev->dev, dev_name(&pdev->dev), >+ devflags); >+ >+ if (IS_ERR(hcd)) >+ return PTR_ERR(hcd); >+ >+ return 0; >+} >+ >+static int __devexit >+isp1760_pdev_remove(struct platform_device *pdev) >+{ >+ struct usb_hcd *hcd = platform_get_drvdata(pdev); >+ >+ platform_set_drvdata(pdev, NULL); >+ >+ usb_remove_hcd(hcd); >+ iounmap(hcd->regs); >+ usb_put_hcd(hcd); >+ return 0; >+} >+ >+/* this driver is exported so sl811_cs can depend on it */ What are you telling me here? >+struct platform_driver isp1760_pdev_driver = { >+ .probe = isp1760_pdev_probe, >+ .remove = __devexit_p(isp1760_pdev_remove), >+ .driver = { >+ .name = "isp1760-hcd", >+ .owner = THIS_MODULE, >+ }, >+}; >+#endif /* USB_ISP1760_PDEV */ >+ > static int __init isp1760_init(void) > { > int ret = -ENODEV; > > init_kmem_once(); > >+#ifdef USB_ISP1760_PDEV >+ ret = platform_driver_register(&isp1760_pdev_driver); >+ if (ret) { >+ deinit_kmem_cache(); >+ return ret; >+ } >+#endif >+ > #ifdef CONFIG_USB_ISP1760_OF > ret = of_register_platform_driver(&isp1760_of_driver); > if (ret) { >@@ -325,6 +420,9 @@ static void __exit isp1760_exit(void) > #ifdef CONFIG_USB_ISP1760_PCI > pci_unregister_driver(&isp1761_pci_driver); > #endif >+#ifdef USB_ISP1760_PDEV >+ platform_driver_unregister(&isp1760_pdev_driver); >+#endif > deinit_kmem_cache(); > } > module_exit(isp1760_exit); >-- >1.5.6.3 Sebastian
next prev parent reply other threads:[~2008-11-06 17:57 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2008-11-06 9:25 [PATCH] USB/ISP1760: Add support for the generic platfrom device centralized driver model Bryan Wu 2008-11-06 17:57 ` Sebastian Andrzej Siewior [this message] 2008-11-06 19:29 ` Hennerich, Michael 2008-11-07 4:00 ` Bryan Wu
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20081106175705.GA4687@www.tglx.de \ --to=bigeasy@linutronix.de \ --cc=cooloney@kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-usb@vger.kernel.org \ --cc=michael.hennerich@analog.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).