LKML Archive on lore.kernel.org
 help / color / Atom feed
From: "Ahmed S. Darwish" <darwish.07@gmail.com>
To: Olivier Sobrie <olivier@sobrie.be>,
	Oliver Hartkopp <socketcan@hartkopp.net>,
	Wolfgang Grandegger <wg@grandegger.com>,
	Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>,
	Paul Gortmaker <paul.gortmaker@windriver.com>,
	Linux-CAN <linux-can@vger.kernel.org>,
	netdev <netdev@vger.kernel.org>,
	LKML <linux-kernel@vger.kernel.org>
Subject: [PATCH v3 4/4] can: kvaser_usb: Add support for the Usbcan-II family
Date: Mon, 5 Jan 2015 13:31:31 -0500
Message-ID: <20150105183131.GD6304@linux> (raw)
In-Reply-To: <20150105175713.GC6304@linux>

From: Ahmed S. Darwish <ahmed.darwish@valeo.com>

CAN to USB interfaces sold by the Swedish manufacturer Kvaser are
divided into two major families: 'Leaf', and 'UsbcanII'.  From an
Operating System perspective, the firmware of both families behave
in a not too drastically different fashion.

This patch adds support for the UsbcanII family of devices to the
current Kvaser Leaf-only driver.

CAN frames sending, receiving, and error handling paths has been
tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It
should also work nicely with other products in the same category.

List of new devices supported by this driver update:

         - Kvaser USBcan II HS/HS
         - Kvaser USBcan II HS/LS
         - Kvaser USBcan Rugged ("USBcan Rev B")
         - Kvaser Memorator HS/HS
         - Kvaser Memorator HS/LS
         - Scania VCI2 (if you have the Kvaser logo on top)

Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
---
 drivers/net/can/usb/Kconfig      |   8 +-
 drivers/net/can/usb/kvaser_usb.c | 618 +++++++++++++++++++++++++++++++--------
 2 files changed, 503 insertions(+), 123 deletions(-)

** V2 Changelog:
- Update Kconfig entries
- Use actual number of CAN channels (instead of max) where appropriate
- Rebase over a new set of UsbcanII-independent driver fixes

** V3 Changelog:
- Fix padding for the usbcan_msg_tx_acknowledge command
- Remove kvaser_usb->max_channels and the MAX_NET_DEVICES macro
- Rename commands to CMD_LEAF_xxx and CMD_USBCAN_xxx
- Apply checkpatch.pl suggestions ('net/' comments, multi-line strings, etc.)

diff --git a/drivers/net/can/usb/Kconfig b/drivers/net/can/usb/Kconfig
index a77db919..f6f5500 100644
--- a/drivers/net/can/usb/Kconfig
+++ b/drivers/net/can/usb/Kconfig
@@ -25,7 +25,7 @@ config CAN_KVASER_USB
 	tristate "Kvaser CAN/USB interface"
 	---help---
 	  This driver adds support for Kvaser CAN/USB devices like Kvaser
-	  Leaf Light.
+	  Leaf Light and Kvaser USBcan II.
 
 	  The driver provides support for the following devices:
 	    - Kvaser Leaf Light
@@ -46,6 +46,12 @@ config CAN_KVASER_USB
 	    - Kvaser USBcan R
 	    - Kvaser Leaf Light v2
 	    - Kvaser Mini PCI Express HS
+	    - Kvaser USBcan II HS/HS
+	    - Kvaser USBcan II HS/LS
+	    - Kvaser USBcan Rugged ("USBcan Rev B")
+	    - Kvaser Memorator HS/HS
+	    - Kvaser Memorator HS/LS
+	    - Scania VCI2 (if you have the Kvaser logo on top)
 
 	  If unsure, say N.
 
diff --git a/drivers/net/can/usb/kvaser_usb.c b/drivers/net/can/usb/kvaser_usb.c
index cc7bfc0..43b3928 100644
--- a/drivers/net/can/usb/kvaser_usb.c
+++ b/drivers/net/can/usb/kvaser_usb.c
@@ -6,10 +6,12 @@
  * Parts of this driver are based on the following:
  *  - Kvaser linux leaf driver (version 4.78)
  *  - CAN driver for esd CAN-USB/2
+ *  - Kvaser linux usbcanII driver (version 5.3)
  *
  * Copyright (C) 2002-2006 KVASER AB, Sweden. All rights reserved.
  * Copyright (C) 2010 Matthias Fuchs <matthias.fuchs@esd.eu>, esd gmbh
  * Copyright (C) 2012 Olivier Sobrie <olivier@sobrie.be>
+ * Copyright (C) 2015 Valeo Corporation
  */
 
 #include <linux/completion.h>
@@ -21,6 +23,15 @@
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
 
+/* Kvaser USB CAN dongles are divided into two major families:
+ * - Leaf: Based on Renesas M32C, running firmware labeled as 'filo'
+ * - UsbcanII: Based on Renesas M16C, running firmware labeled as 'helios'
+ */
+enum kvaser_usb_family {
+	KVASER_LEAF,
+	KVASER_USBCAN,
+};
+
 #define MAX_TX_URBS			16
 #define MAX_RX_URBS			4
 #define START_TIMEOUT			1000 /* msecs */
@@ -30,8 +41,9 @@
 #define RX_BUFFER_SIZE			3072
 #define CAN_USB_CLOCK			8000000
 #define MAX_NET_DEVICES			3
+#define MAX_USBCAN_NET_DEVICES		2
 
-/* Kvaser USB devices */
+/* Leaf USB devices */
 #define KVASER_VENDOR_ID		0x0bfd
 #define USB_LEAF_DEVEL_PRODUCT_ID	10
 #define USB_LEAF_LITE_PRODUCT_ID	11
@@ -55,6 +67,16 @@
 #define USB_CAN_R_PRODUCT_ID		39
 #define USB_LEAF_LITE_V2_PRODUCT_ID	288
 #define USB_MINI_PCIE_HS_PRODUCT_ID	289
+#define LEAF_PRODUCT_ID(id)		(id >= USB_LEAF_DEVEL_PRODUCT_ID && \
+					 id <= USB_MINI_PCIE_HS_PRODUCT_ID)
+
+/* USBCANII devices */
+#define USB_USBCAN_REVB_PRODUCT_ID	2
+#define USB_VCI2_PRODUCT_ID		3
+#define USB_USBCAN2_PRODUCT_ID		4
+#define USB_MEMORATOR_PRODUCT_ID	5
+#define USBCAN_PRODUCT_ID(id)		(id >= USB_USBCAN_REVB_PRODUCT_ID && \
+					 id <= USB_MEMORATOR_PRODUCT_ID)
 
 /* USB devices features */
 #define KVASER_HAS_SILENT_MODE		BIT(0)
@@ -73,7 +95,7 @@
 #define MSG_FLAG_TX_ACK			BIT(6)
 #define MSG_FLAG_TX_REQUEST		BIT(7)
 
-/* Can states */
+/* Can states (M16C CxSTRH register) */
 #define M16C_STATE_BUS_RESET		BIT(0)
 #define M16C_STATE_BUS_ERROR		BIT(4)
 #define M16C_STATE_BUS_PASSIVE		BIT(5)
@@ -98,7 +120,13 @@
 #define CMD_START_CHIP_REPLY		27
 #define CMD_STOP_CHIP			28
 #define CMD_STOP_CHIP_REPLY		29
-#define CMD_GET_CARD_INFO2		32
+#define CMD_READ_CLOCK			30
+#define CMD_READ_CLOCK_REPLY		31
+
+#define CMD_LEAF_GET_CARD_INFO2		32
+#define CMD_USBCAN_RESET_CLOCK		32
+#define CMD_USBCAN_CLOCK_OVERFLOW_EVENT	33
+
 #define CMD_GET_CARD_INFO		34
 #define CMD_GET_CARD_INFO_REPLY		35
 #define CMD_GET_SOFTWARE_INFO		38
@@ -108,8 +136,9 @@
 #define CMD_RESET_ERROR_COUNTER		49
 #define CMD_TX_ACKNOWLEDGE		50
 #define CMD_CAN_ERROR_EVENT		51
-#define CMD_USB_THROTTLE		77
-#define CMD_LOG_MESSAGE			106
+
+#define CMD_LEAF_USB_THROTTLE		77
+#define CMD_LEAF_LOG_MESSAGE		106
 
 /* error factors */
 #define M16C_EF_ACKE			BIT(0)
@@ -121,6 +150,14 @@
 #define M16C_EF_RCVE			BIT(6)
 #define M16C_EF_TRE			BIT(7)
 
+/* Only Leaf-based devices can report M16C error factors,
+ * thus define our own error status flags for USBCANII
+ */
+#define USBCAN_ERROR_STATE_NONE		0
+#define USBCAN_ERROR_STATE_TX_ERROR	BIT(0)
+#define USBCAN_ERROR_STATE_RX_ERROR	BIT(1)
+#define USBCAN_ERROR_STATE_BUSERROR	BIT(2)
+
 /* bittiming parameters */
 #define KVASER_USB_TSEG1_MIN		1
 #define KVASER_USB_TSEG1_MAX		16
@@ -137,7 +174,7 @@
 #define KVASER_CTRL_MODE_SELFRECEPTION	3
 #define KVASER_CTRL_MODE_OFF		4
 
-/* log message */
+/* Extended CAN identifier flag */
 #define KVASER_EXTENDED_FRAME		BIT(31)
 
 struct kvaser_msg_simple {
@@ -148,30 +185,55 @@ struct kvaser_msg_simple {
 struct kvaser_msg_cardinfo {
 	u8 tid;
 	u8 nchannels;
-	__le32 serial_number;
-	__le32 padding;
+	union {
+		struct {
+			__le32 serial_number;
+			__le32 padding;
+		} __packed leaf0;
+		struct {
+			__le32 serial_number_low;
+			__le32 serial_number_high;
+		} __packed usbcan0;
+	} __packed;
 	__le32 clock_resolution;
 	__le32 mfgdate;
 	u8 ean[8];
 	u8 hw_revision;
-	u8 usb_hs_mode;
-	__le16 padding2;
+	union {
+		struct {
+			u8 usb_hs_mode;
+		} __packed leaf1;
+		struct {
+			u8 padding;
+		} __packed usbcan1;
+	} __packed;
+	__le16 padding;
 } __packed;
 
 struct kvaser_msg_cardinfo2 {
 	u8 tid;
-	u8 channel;
+	u8 reserved;
 	u8 pcb_id[24];
 	__le32 oem_unlock_code;
 } __packed;
 
-struct kvaser_msg_softinfo {
+struct leaf_msg_softinfo {
 	u8 tid;
-	u8 channel;
+	u8 padding0;
 	__le32 sw_options;
 	__le32 fw_version;
 	__le16 max_outstanding_tx;
-	__le16 padding[9];
+	__le16 padding1[9];
+} __packed;
+
+struct usbcan_msg_softinfo {
+	u8 tid;
+	u8 fw_name[5];
+	__le16 max_outstanding_tx;
+	u8 padding[6];
+	__le32 fw_version;
+	__le16 checksum;
+	__le16 sw_options;
 } __packed;
 
 struct kvaser_msg_busparams {
@@ -188,36 +250,86 @@ struct kvaser_msg_tx_can {
 	u8 channel;
 	u8 tid;
 	u8 msg[14];
-	u8 padding;
-	u8 flags;
+	union {
+		struct {
+			u8 padding;
+			u8 flags;
+		} __packed leaf;
+		struct {
+			u8 flags;
+			u8 padding;
+		} __packed usbcan;
+	} __packed;
 } __packed;
 
-struct kvaser_msg_rx_can {
+struct kvaser_msg_rx_can_header {
 	u8 channel;
 	u8 flag;
+} __packed;
+
+struct leaf_msg_rx_can {
+	u8 channel;
+	u8 flag;
+
 	__le16 time[3];
 	u8 msg[14];
 } __packed;
 
-struct kvaser_msg_chip_state_event {
+struct usbcan_msg_rx_can {
+	u8 channel;
+	u8 flag;
+
+	u8 msg[14];
+	__le16 time;
+} __packed;
+
+struct leaf_msg_chip_state_event {
 	u8 tid;
 	u8 channel;
+
 	__le16 time[3];
 	u8 tx_errors_count;
 	u8 rx_errors_count;
+
+	u8 status;
+	u8 padding[3];
+} __packed;
+
+struct usbcan_msg_chip_state_event {
+	u8 tid;
+	u8 channel;
+
+	u8 tx_errors_count;
+	u8 rx_errors_count;
+	__le16 time;
+
 	u8 status;
 	u8 padding[3];
 } __packed;
 
-struct kvaser_msg_tx_acknowledge {
+struct kvaser_msg_tx_acknowledge_header {
+	u8 channel;
+	u8 tid;
+};
+
+struct leaf_msg_tx_acknowledge {
 	u8 channel;
 	u8 tid;
+
 	__le16 time[3];
 	u8 flags;
 	u8 time_offset;
 } __packed;
 
-struct kvaser_msg_error_event {
+struct usbcan_msg_tx_acknowledge {
+	u8 channel;
+	u8 tid;
+
+	__le16 time;
+	__le16 padding;
+} __packed;
+
+struct leaf_msg_error_event {
 	u8 tid;
 	u8 flags;
 	__le16 time[3];
@@ -229,6 +341,18 @@ struct kvaser_msg_error_event {
 	u8 error_factor;
 } __packed;
 
+struct usbcan_msg_error_event {
+	u8 tid;
+	u8 padding;
+	u8 tx_errors_count_ch0;
+	u8 rx_errors_count_ch0;
+	u8 tx_errors_count_ch1;
+	u8 rx_errors_count_ch1;
+	u8 status_ch0;
+	u8 status_ch1;
+	__le16 time;
+} __packed;
+
 struct kvaser_msg_ctrl_mode {
 	u8 tid;
 	u8 channel;
@@ -243,7 +367,7 @@ struct kvaser_msg_flush_queue {
 	u8 padding[3];
 } __packed;
 
-struct kvaser_msg_log_message {
+struct leaf_msg_log_message {
 	u8 channel;
 	u8 flags;
 	__le16 time[3];
@@ -260,19 +384,50 @@ struct kvaser_msg {
 		struct kvaser_msg_simple simple;
 		struct kvaser_msg_cardinfo cardinfo;
 		struct kvaser_msg_cardinfo2 cardinfo2;
-		struct kvaser_msg_softinfo softinfo;
 		struct kvaser_msg_busparams busparams;
+
+		struct kvaser_msg_rx_can_header rx_can_header;
+		struct kvaser_msg_tx_acknowledge_header tx_acknowledge_header;
+
+		union {
+			struct leaf_msg_softinfo softinfo;
+			struct leaf_msg_rx_can rx_can;
+			struct leaf_msg_chip_state_event chip_state_event;
+			struct leaf_msg_tx_acknowledge tx_acknowledge;
+			struct leaf_msg_error_event error_event;
+			struct leaf_msg_log_message log_message;
+		} __packed leaf;
+
+		union {
+			struct usbcan_msg_softinfo softinfo;
+			struct usbcan_msg_rx_can rx_can;
+			struct usbcan_msg_chip_state_event chip_state_event;
+			struct usbcan_msg_tx_acknowledge tx_acknowledge;
+			struct usbcan_msg_error_event error_event;
+		} __packed usbcan;
+
 		struct kvaser_msg_tx_can tx_can;
-		struct kvaser_msg_rx_can rx_can;
-		struct kvaser_msg_chip_state_event chip_state_event;
-		struct kvaser_msg_tx_acknowledge tx_acknowledge;
-		struct kvaser_msg_error_event error_event;
 		struct kvaser_msg_ctrl_mode ctrl_mode;
 		struct kvaser_msg_flush_queue flush_queue;
-		struct kvaser_msg_log_message log_message;
 	} u;
 } __packed;
 
+/* Leaf/USBCAN-agnostic summary of an error event.
+ * No M16C error factors for USBCAN-based devices.
+ */
+struct kvaser_error_summary {
+	u8 channel, status, txerr, rxerr;
+	union {
+		struct {
+			u8 error_factor;
+		} leaf;
+		struct {
+			u8 other_ch_status;
+			u8 error_state;
+		} usbcan;
+	};
+};
+
 struct kvaser_usb_tx_urb_context {
 	struct kvaser_usb_net_priv *priv;
 	u32 echo_index;
@@ -288,6 +443,7 @@ struct kvaser_usb {
 
 	u32 fw_version;
 	unsigned int nchannels;
+	enum kvaser_usb_family family;
 
 	bool rxinitdone;
 	void *rxbuf[MAX_RX_URBS];
@@ -311,6 +467,7 @@ struct kvaser_usb_net_priv {
 };
 
 static const struct usb_device_id kvaser_usb_table[] = {
+	/* Leaf family IDs */
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_DEVEL_PRODUCT_ID) },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_PRODUCT_ID) },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_PRODUCT_ID),
@@ -360,6 +517,17 @@ static const struct usb_device_id kvaser_usb_table[] = {
 		.driver_info = KVASER_HAS_TXRX_ERRORS },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_V2_PRODUCT_ID) },
 	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_HS_PRODUCT_ID) },
+
+	/* USBCANII family IDs */
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN2_PRODUCT_ID),
+		.driver_info = KVASER_HAS_TXRX_ERRORS },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_REVB_PRODUCT_ID),
+		.driver_info = KVASER_HAS_TXRX_ERRORS },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_MEMORATOR_PRODUCT_ID),
+		.driver_info = KVASER_HAS_TXRX_ERRORS },
+	{ USB_DEVICE(KVASER_VENDOR_ID, USB_VCI2_PRODUCT_ID),
+		.driver_info = KVASER_HAS_TXRX_ERRORS },
+
 	{ }
 };
 MODULE_DEVICE_TABLE(usb, kvaser_usb_table);
@@ -463,7 +631,18 @@ static int kvaser_usb_get_software_info(struct kvaser_usb *dev)
 	if (err)
 		return err;
 
-	dev->fw_version = le32_to_cpu(msg.u.softinfo.fw_version);
+	switch (dev->family) {
+	case KVASER_LEAF:
+		dev->fw_version = le32_to_cpu(msg.u.leaf.softinfo.fw_version);
+		break;
+	case KVASER_USBCAN:
+		dev->fw_version = le32_to_cpu(msg.u.usbcan.softinfo.fw_version);
+		break;
+	default:
+		dev_err(dev->udev->dev.parent,
+			"Invalid device family (%d)\n", dev->family);
+		return -EINVAL;
+	}
 
 	return 0;
 }
@@ -484,6 +663,9 @@ static int kvaser_usb_get_card_info(struct kvaser_usb *dev)
 	dev->nchannels = msg.u.cardinfo.nchannels;
 	if (dev->nchannels > MAX_NET_DEVICES)
 		return -EINVAL;
+	if (dev->family == KVASER_USBCAN &&
+	    dev->nchannels > MAX_USBCAN_NET_DEVICES)
+		return -EINVAL;
 
 	return 0;
 }
@@ -496,8 +678,10 @@ static void kvaser_usb_tx_acknowledge(const struct kvaser_usb *dev,
 	struct kvaser_usb_net_priv *priv;
 	struct sk_buff *skb;
 	struct can_frame *cf;
-	u8 channel = msg->u.tx_acknowledge.channel;
-	u8 tid = msg->u.tx_acknowledge.tid;
+	u8 channel, tid;
+
+	channel = msg->u.tx_acknowledge_header.channel;
+	tid = msg->u.tx_acknowledge_header.tid;
 
 	if (channel >= dev->nchannels) {
 		dev_err(dev->udev->dev.parent,
@@ -615,37 +799,80 @@ static void kvaser_usb_unlink_tx_urbs(struct kvaser_usb_net_priv *priv)
 		priv->tx_contexts[i].echo_index = MAX_TX_URBS;
 }
 
-static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
-				const struct kvaser_msg *msg)
+static void kvaser_report_error_event(const struct kvaser_usb *dev,
+				      struct kvaser_error_summary *es);
+
+/* Report error to userspace iff the controller's errors counter has
+ * increased, or we're the only channel seeing the bus error state.
+ *
+ * As reported by USBCAN sheets, "the CAN controller has difficulties
+ * to tell whether an error frame arrived on channel 1 or on channel 2."
+ * Thus, error counters are compared with their earlier values to
+ * determine which channel was responsible for the error event.
+ */
+static void usbcan_report_error_if_applicable(const struct kvaser_usb *dev,
+					      struct kvaser_error_summary *es)
 {
-	struct can_frame *cf;
-	struct sk_buff *skb;
-	struct net_device_stats *stats;
 	struct kvaser_usb_net_priv *priv;
-	unsigned int new_state;
-	u8 channel, status, txerr, rxerr, error_factor;
+	int old_tx_err_count, old_rx_err_count, channel, report_error;
+
+	channel = es->channel;
+	if (channel >= dev->nchannels) {
+		dev_err(dev->udev->dev.parent,
+			"Invalid channel number (%d)\n", channel);
+		return;
+	}
+
+	priv = dev->nets[channel];
+	old_tx_err_count = priv->bec.txerr;
+	old_rx_err_count = priv->bec.rxerr;
+
+	report_error = 0;
+	if (es->txerr > old_tx_err_count) {
+		es->usbcan.error_state |= USBCAN_ERROR_STATE_TX_ERROR;
+		report_error = 1;
+	}
+	if (es->rxerr > old_rx_err_count) {
+		es->usbcan.error_state |= USBCAN_ERROR_STATE_RX_ERROR;
+		report_error = 1;
+	}
+	if ((es->status & M16C_STATE_BUS_ERROR) &&
+	    !(es->usbcan.other_ch_status & M16C_STATE_BUS_ERROR)) {
+		es->usbcan.error_state |= USBCAN_ERROR_STATE_BUSERROR;
+		report_error = 1;
+	}
+
+	if (report_error)
+		kvaser_report_error_event(dev, es);
+}
+
+/* Extract error summary from a Leaf-based device error message */
+static void leaf_extract_error_from_msg(const struct kvaser_usb *dev,
+					const struct kvaser_msg *msg)
+{
+	struct kvaser_error_summary es = { 0, };
 
 	switch (msg->id) {
 	case CMD_CAN_ERROR_EVENT:
-		channel = msg->u.error_event.channel;
-		status =  msg->u.error_event.status;
-		txerr = msg->u.error_event.tx_errors_count;
-		rxerr = msg->u.error_event.rx_errors_count;
-		error_factor = msg->u.error_event.error_factor;
+		es.channel = msg->u.leaf.error_event.channel;
+		es.status =  msg->u.leaf.error_event.status;
+		es.txerr = msg->u.leaf.error_event.tx_errors_count;
+		es.rxerr = msg->u.leaf.error_event.rx_errors_count;
+		es.leaf.error_factor = msg->u.leaf.error_event.error_factor;
 		break;
-	case CMD_LOG_MESSAGE:
-		channel = msg->u.log_message.channel;
-		status = msg->u.log_message.data[0];
-		txerr = msg->u.log_message.data[2];
-		rxerr = msg->u.log_message.data[3];
-		error_factor = msg->u.log_message.data[1];
+	case CMD_LEAF_LOG_MESSAGE:
+		es.channel = msg->u.leaf.log_message.channel;
+		es.status = msg->u.leaf.log_message.data[0];
+		es.txerr = msg->u.leaf.log_message.data[2];
+		es.rxerr = msg->u.leaf.log_message.data[3];
+		es.leaf.error_factor = msg->u.leaf.log_message.data[1];
 		break;
 	case CMD_CHIP_STATE_EVENT:
-		channel = msg->u.chip_state_event.channel;
-		status =  msg->u.chip_state_event.status;
-		txerr = msg->u.chip_state_event.tx_errors_count;
-		rxerr = msg->u.chip_state_event.rx_errors_count;
-		error_factor = 0;
+		es.channel = msg->u.leaf.chip_state_event.channel;
+		es.status =  msg->u.leaf.chip_state_event.status;
+		es.txerr = msg->u.leaf.chip_state_event.tx_errors_count;
+		es.rxerr = msg->u.leaf.chip_state_event.rx_errors_count;
+		es.leaf.error_factor = 0;
 		break;
 	default:
 		dev_err(dev->udev->dev.parent, "Invalid msg id (%d)\n",
@@ -653,16 +880,92 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 		return;
 	}
 
-	if (channel >= dev->nchannels) {
+	kvaser_report_error_event(dev, &es);
+}
+
+/* Extract error summary from a USBCANII-based device error message */
+static void usbcan_extract_error_from_msg(const struct kvaser_usb *dev,
+					  const struct kvaser_msg *msg)
+{
+	struct kvaser_error_summary es = { 0, };
+
+	switch (msg->id) {
+	/* Sometimes errors are sent as unsolicited chip state events */
+	case CMD_CHIP_STATE_EVENT:
+		es.channel = msg->u.usbcan.chip_state_event.channel;
+		es.status =  msg->u.usbcan.chip_state_event.status;
+		es.txerr = msg->u.usbcan.chip_state_event.tx_errors_count;
+		es.rxerr = msg->u.usbcan.chip_state_event.rx_errors_count;
+		usbcan_report_error_if_applicable(dev, &es);
+		break;
+
+	case CMD_CAN_ERROR_EVENT:
+		es.channel = 0;
+		es.status = msg->u.usbcan.error_event.status_ch0;
+		es.txerr = msg->u.usbcan.error_event.tx_errors_count_ch0;
+		es.rxerr = msg->u.usbcan.error_event.rx_errors_count_ch0;
+		es.usbcan.other_ch_status =
+			msg->u.usbcan.error_event.status_ch1;
+		usbcan_report_error_if_applicable(dev, &es);
+
+		/* For error events, the USBCAN firmware does not support
+		 * more than 2 channels: ch0, and ch1.
+		 */
+		if (dev->nchannels > 1) {
+			es.channel = 1;
+			es.status = msg->u.usbcan.error_event.status_ch1;
+			es.txerr =
+				msg->u.usbcan.error_event.tx_errors_count_ch1;
+			es.rxerr =
+				msg->u.usbcan.error_event.rx_errors_count_ch1;
+			es.usbcan.other_ch_status =
+				msg->u.usbcan.error_event.status_ch0;
+			usbcan_report_error_if_applicable(dev, &es);
+		}
+		break;
+
+	default:
+		dev_err(dev->udev->dev.parent, "Invalid msg id (%d)\n",
+			msg->id);
+	}
+}
+
+static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
+				const struct kvaser_msg *msg)
+{
+	switch (dev->family) {
+	case KVASER_LEAF:
+		leaf_extract_error_from_msg(dev, msg);
+		break;
+	case KVASER_USBCAN:
+		usbcan_extract_error_from_msg(dev, msg);
+		break;
+	default:
 		dev_err(dev->udev->dev.parent,
-			"Invalid channel number (%d)\n", channel);
+			"Invalid device family (%d)\n", dev->family);
 		return;
 	}
+}
 
-	priv = dev->nets[channel];
+static void kvaser_report_error_event(const struct kvaser_usb *dev,
+				      struct kvaser_error_summary *es)
+{
+	struct can_frame *cf;
+	struct sk_buff *skb;
+	struct net_device_stats *stats;
+	struct kvaser_usb_net_priv *priv;
+	unsigned int new_state;
+
+	if (es->channel >= dev->nchannels) {
+		dev_err(dev->udev->dev.parent,
+			"Invalid channel number (%d)\n", es->channel);
+		return;
+	}
+
+	priv = dev->nets[es->channel];
 	stats = &priv->netdev->stats;
 
-	if (status & M16C_STATE_BUS_RESET) {
+	if (es->status & M16C_STATE_BUS_RESET) {
 		kvaser_usb_unlink_tx_urbs(priv);
 		return;
 	}
@@ -675,9 +978,9 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 
 	new_state = priv->can.state;
 
-	netdev_dbg(priv->netdev, "Error status: 0x%02x\n", status);
+	netdev_dbg(priv->netdev, "Error status: 0x%02x\n", es->status);
 
-	if (status & M16C_STATE_BUS_OFF) {
+	if (es->status & M16C_STATE_BUS_OFF) {
 		cf->can_id |= CAN_ERR_BUSOFF;
 
 		priv->can.can_stats.bus_off++;
@@ -687,12 +990,12 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 		netif_carrier_off(priv->netdev);
 
 		new_state = CAN_STATE_BUS_OFF;
-	} else if (status & M16C_STATE_BUS_PASSIVE) {
+	} else if (es->status & M16C_STATE_BUS_PASSIVE) {
 		if (priv->can.state != CAN_STATE_ERROR_PASSIVE) {
 			cf->can_id |= CAN_ERR_CRTL;
 
-			if (txerr || rxerr)
-				cf->data[1] = (txerr > rxerr)
+			if (es->txerr || es->rxerr)
+				cf->data[1] = (es->txerr > es->rxerr)
 						? CAN_ERR_CRTL_TX_PASSIVE
 						: CAN_ERR_CRTL_RX_PASSIVE;
 			else
@@ -703,13 +1006,11 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 		}
 
 		new_state = CAN_STATE_ERROR_PASSIVE;
-	}
-
-	if (status == M16C_STATE_BUS_ERROR) {
+	} else if (es->status & M16C_STATE_BUS_ERROR) {
 		if ((priv->can.state < CAN_STATE_ERROR_WARNING) &&
-		    ((txerr >= 96) || (rxerr >= 96))) {
+		    ((es->txerr >= 96) || (es->rxerr >= 96))) {
 			cf->can_id |= CAN_ERR_CRTL;
-			cf->data[1] = (txerr > rxerr)
+			cf->data[1] = (es->txerr > es->rxerr)
 					? CAN_ERR_CRTL_TX_WARNING
 					: CAN_ERR_CRTL_RX_WARNING;
 
@@ -723,7 +1024,7 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 		}
 	}
 
-	if (!status) {
+	if (!es->status) {
 		cf->can_id |= CAN_ERR_PROT;
 		cf->data[2] = CAN_ERR_PROT_ACTIVE;
 
@@ -739,34 +1040,52 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 		priv->can.can_stats.restarts++;
 	}
 
-	if (error_factor) {
-		priv->can.can_stats.bus_error++;
-		stats->rx_errors++;
-
-		cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT;
-
-		if (error_factor & M16C_EF_ACKE)
-			cf->data[3] |= (CAN_ERR_PROT_LOC_ACK);
-		if (error_factor & M16C_EF_CRCE)
-			cf->data[3] |= (CAN_ERR_PROT_LOC_CRC_SEQ |
-					CAN_ERR_PROT_LOC_CRC_DEL);
-		if (error_factor & M16C_EF_FORME)
-			cf->data[2] |= CAN_ERR_PROT_FORM;
-		if (error_factor & M16C_EF_STFE)
-			cf->data[2] |= CAN_ERR_PROT_STUFF;
-		if (error_factor & M16C_EF_BITE0)
-			cf->data[2] |= CAN_ERR_PROT_BIT0;
-		if (error_factor & M16C_EF_BITE1)
-			cf->data[2] |= CAN_ERR_PROT_BIT1;
-		if (error_factor & M16C_EF_TRE)
-			cf->data[2] |= CAN_ERR_PROT_TX;
+	switch (dev->family) {
+	case KVASER_LEAF:
+		if (es->leaf.error_factor) {
+			priv->can.can_stats.bus_error++;
+			stats->rx_errors++;
+
+			cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT;
+
+			if (es->leaf.error_factor & M16C_EF_ACKE)
+				cf->data[3] |= (CAN_ERR_PROT_LOC_ACK);
+			if (es->leaf.error_factor & M16C_EF_CRCE)
+				cf->data[3] |= (CAN_ERR_PROT_LOC_CRC_SEQ |
+						CAN_ERR_PROT_LOC_CRC_DEL);
+			if (es->leaf.error_factor & M16C_EF_FORME)
+				cf->data[2] |= CAN_ERR_PROT_FORM;
+			if (es->leaf.error_factor & M16C_EF_STFE)
+				cf->data[2] |= CAN_ERR_PROT_STUFF;
+			if (es->leaf.error_factor & M16C_EF_BITE0)
+				cf->data[2] |= CAN_ERR_PROT_BIT0;
+			if (es->leaf.error_factor & M16C_EF_BITE1)
+				cf->data[2] |= CAN_ERR_PROT_BIT1;
+			if (es->leaf.error_factor & M16C_EF_TRE)
+				cf->data[2] |= CAN_ERR_PROT_TX;
+		}
+		break;
+	case KVASER_USBCAN:
+		if (es->usbcan.error_state & USBCAN_ERROR_STATE_TX_ERROR)
+			stats->tx_errors++;
+		if (es->usbcan.error_state & USBCAN_ERROR_STATE_RX_ERROR)
+			stats->rx_errors++;
+		if (es->usbcan.error_state & USBCAN_ERROR_STATE_BUSERROR) {
+			priv->can.can_stats.bus_error++;
+			cf->can_id |= CAN_ERR_BUSERROR;
+		}
+		break;
+	default:
+		dev_err(dev->udev->dev.parent,
+			"Invalid device family (%d)\n", dev->family);
+		goto err;
 	}
 
-	cf->data[6] = txerr;
-	cf->data[7] = rxerr;
+	cf->data[6] = es->txerr;
+	cf->data[7] = es->rxerr;
 
-	priv->bec.txerr = txerr;
-	priv->bec.rxerr = rxerr;
+	priv->bec.txerr = es->txerr;
+	priv->bec.rxerr = es->rxerr;
 
 	priv->can.state = new_state;
 
@@ -774,6 +1093,11 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev,
 
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
+
+	return;
+
+err:
+	dev_kfree_skb(skb);
 }
 
 static void kvaser_usb_rx_can_err(const struct kvaser_usb_net_priv *priv,
@@ -783,16 +1107,16 @@ static void kvaser_usb_rx_can_err(const struct kvaser_usb_net_priv *priv,
 	struct sk_buff *skb;
 	struct net_device_stats *stats = &priv->netdev->stats;
 
-	if (msg->u.rx_can.flag & (MSG_FLAG_ERROR_FRAME |
+	if (msg->u.rx_can_header.flag & (MSG_FLAG_ERROR_FRAME |
 					 MSG_FLAG_NERR)) {
 		netdev_err(priv->netdev, "Unknow error (flags: 0x%02x)\n",
-			   msg->u.rx_can.flag);
+			   msg->u.rx_can_header.flag);
 
 		stats->rx_errors++;
 		return;
 	}
 
-	if (msg->u.rx_can.flag & MSG_FLAG_OVERRUN) {
+	if (msg->u.rx_can_header.flag & MSG_FLAG_OVERRUN) {
 		skb = alloc_can_err_skb(priv->netdev, &cf);
 		if (!skb) {
 			stats->rx_dropped++;
@@ -819,7 +1143,8 @@ static void kvaser_usb_rx_can_msg(const struct kvaser_usb *dev,
 	struct can_frame *cf;
 	struct sk_buff *skb;
 	struct net_device_stats *stats;
-	u8 channel = msg->u.rx_can.channel;
+	u8 channel = msg->u.rx_can_header.channel;
+	const u8 *rx_msg;
 
 	if (channel >= dev->nchannels) {
 		dev_err(dev->udev->dev.parent,
@@ -830,19 +1155,32 @@ static void kvaser_usb_rx_can_msg(const struct kvaser_usb *dev,
 	priv = dev->nets[channel];
 	stats = &priv->netdev->stats;
 
-	if ((msg->u.rx_can.flag & MSG_FLAG_ERROR_FRAME) &&
-	    (msg->id == CMD_LOG_MESSAGE)) {
+	if ((msg->u.rx_can_header.flag & MSG_FLAG_ERROR_FRAME) &&
+	    (dev->family == KVASER_LEAF && msg->id == CMD_LEAF_LOG_MESSAGE)) {
 		kvaser_usb_rx_error(dev, msg);
 		return;
-	} else if (msg->u.rx_can.flag & (MSG_FLAG_ERROR_FRAME |
-					 MSG_FLAG_NERR |
-					 MSG_FLAG_OVERRUN)) {
+	} else if (msg->u.rx_can_header.flag & (MSG_FLAG_ERROR_FRAME |
+						MSG_FLAG_NERR |
+						MSG_FLAG_OVERRUN)) {
 		kvaser_usb_rx_can_err(priv, msg);
 		return;
-	} else if (msg->u.rx_can.flag & ~MSG_FLAG_REMOTE_FRAME) {
+	} else if (msg->u.rx_can_header.flag & ~MSG_FLAG_REMOTE_FRAME) {
 		netdev_warn(priv->netdev,
 			    "Unhandled frame (flags: 0x%02x)",
-			    msg->u.rx_can.flag);
+			    msg->u.rx_can_header.flag);
+		return;
+	}
+
+	switch (dev->family) {
+	case KVASER_LEAF:
+		rx_msg = msg->u.leaf.rx_can.msg;
+		break;
+	case KVASER_USBCAN:
+		rx_msg = msg->u.usbcan.rx_can.msg;
+		break;
+	default:
+		dev_err(dev->udev->dev.parent,
+			"Invalid device family (%d)\n", dev->family);
 		return;
 	}
 
@@ -852,38 +1190,37 @@ static void kvaser_usb_rx_can_msg(const struct kvaser_usb *dev,
 		return;
 	}
 
-	if (msg->id == CMD_LOG_MESSAGE) {
-		cf->can_id = le32_to_cpu(msg->u.log_message.id);
+	if (dev->family == KVASER_LEAF && msg->id == CMD_LEAF_LOG_MESSAGE) {
+		cf->can_id = le32_to_cpu(msg->u.leaf.log_message.id);
 		if (cf->can_id & KVASER_EXTENDED_FRAME)
 			cf->can_id &= CAN_EFF_MASK | CAN_EFF_FLAG;
 		else
 			cf->can_id &= CAN_SFF_MASK;
 
-		cf->can_dlc = get_can_dlc(msg->u.log_message.dlc);
+		cf->can_dlc = get_can_dlc(msg->u.leaf.log_message.dlc);
 
-		if (msg->u.log_message.flags & MSG_FLAG_REMOTE_FRAME)
+		if (msg->u.leaf.log_message.flags & MSG_FLAG_REMOTE_FRAME)
 			cf->can_id |= CAN_RTR_FLAG;
 		else
-			memcpy(cf->data, &msg->u.log_message.data,
+			memcpy(cf->data, &msg->u.leaf.log_message.data,
 			       cf->can_dlc);
 	} else {
-		cf->can_id = ((msg->u.rx_can.msg[0] & 0x1f) << 6) |
-			     (msg->u.rx_can.msg[1] & 0x3f);
+		cf->can_id = ((rx_msg[0] & 0x1f) << 6) | (rx_msg[1] & 0x3f);
 
 		if (msg->id == CMD_RX_EXT_MESSAGE) {
 			cf->can_id <<= 18;
-			cf->can_id |= ((msg->u.rx_can.msg[2] & 0x0f) << 14) |
-				      ((msg->u.rx_can.msg[3] & 0xff) << 6) |
-				      (msg->u.rx_can.msg[4] & 0x3f);
+			cf->can_id |= ((rx_msg[2] & 0x0f) << 14) |
+				      ((rx_msg[3] & 0xff) << 6) |
+				      (rx_msg[4] & 0x3f);
 			cf->can_id |= CAN_EFF_FLAG;
 		}
 
-		cf->can_dlc = get_can_dlc(msg->u.rx_can.msg[5]);
+		cf->can_dlc = get_can_dlc(rx_msg[5]);
 
-		if (msg->u.rx_can.flag & MSG_FLAG_REMOTE_FRAME)
+		if (msg->u.rx_can_header.flag & MSG_FLAG_REMOTE_FRAME)
 			cf->can_id |= CAN_RTR_FLAG;
 		else
-			memcpy(cf->data, &msg->u.rx_can.msg[6],
+			memcpy(cf->data, &rx_msg[6],
 			       cf->can_dlc);
 	}
 
@@ -947,7 +1284,12 @@ static void kvaser_usb_handle_message(const struct kvaser_usb *dev,
 
 	case CMD_RX_STD_MESSAGE:
 	case CMD_RX_EXT_MESSAGE:
-	case CMD_LOG_MESSAGE:
+		kvaser_usb_rx_can_msg(dev, msg);
+		break;
+
+	case CMD_LEAF_LOG_MESSAGE:
+		if (dev->family != KVASER_LEAF)
+			goto warn;
 		kvaser_usb_rx_can_msg(dev, msg);
 		break;
 
@@ -960,8 +1302,14 @@ static void kvaser_usb_handle_message(const struct kvaser_usb *dev,
 		kvaser_usb_tx_acknowledge(dev, msg);
 		break;
 
+	/* Ignored messages */
+	case CMD_USBCAN_CLOCK_OVERFLOW_EVENT:
+		if (dev->family != KVASER_USBCAN)
+			goto warn;
+		break;
+
 	default:
-		dev_warn(dev->udev->dev.parent,
+warn:		dev_warn(dev->udev->dev.parent,
 			 "Unhandled message (%d)\n", msg->id);
 		break;
 	}
@@ -1181,7 +1529,7 @@ static void kvaser_usb_unlink_all_urbs(struct kvaser_usb *dev)
 				  dev->rxbuf[i],
 				  dev->rxbuf_dma[i]);
 
-	for (i = 0; i < MAX_NET_DEVICES; i++) {
+	for (i = 0; i < dev->nchannels; i++) {
 		struct kvaser_usb_net_priv *priv = dev->nets[i];
 
 		if (priv)
@@ -1289,6 +1637,7 @@ static netdev_tx_t kvaser_usb_start_xmit(struct sk_buff *skb,
 	struct kvaser_msg *msg;
 	int i, err;
 	int ret = NETDEV_TX_OK;
+	uint8_t *msg_tx_can_flags;
 
 	if (can_dropped_invalid_skb(netdev, skb))
 		return NETDEV_TX_OK;
@@ -1310,9 +1659,23 @@ static netdev_tx_t kvaser_usb_start_xmit(struct sk_buff *skb,
 
 	msg = buf;
 	msg->len = MSG_HEADER_LEN + sizeof(struct kvaser_msg_tx_can);
-	msg->u.tx_can.flags = 0;
 	msg->u.tx_can.channel = priv->channel;
 
+	switch (dev->family) {
+	case KVASER_LEAF:
+		msg_tx_can_flags = &msg->u.tx_can.leaf.flags;
+		break;
+	case KVASER_USBCAN:
+		msg_tx_can_flags = &msg->u.tx_can.usbcan.flags;
+		break;
+	default:
+		dev_err(dev->udev->dev.parent,
+			"Invalid device family (%d)\n", dev->family);
+		goto releasebuf;
+	}
+
+	*msg_tx_can_flags = 0;
+
 	if (cf->can_id & CAN_EFF_FLAG) {
 		msg->id = CMD_TX_EXT_MESSAGE;
 		msg->u.tx_can.msg[0] = (cf->can_id >> 24) & 0x1f;
@@ -1330,7 +1693,7 @@ static netdev_tx_t kvaser_usb_start_xmit(struct sk_buff *skb,
 	memcpy(&msg->u.tx_can.msg[6], cf->data, cf->can_dlc);
 
 	if (cf->can_id & CAN_RTR_FLAG)
-		msg->u.tx_can.flags |= MSG_FLAG_REMOTE_FRAME;
+		*msg_tx_can_flags |= MSG_FLAG_REMOTE_FRAME;
 
 	for (i = 0; i < ARRAY_SIZE(priv->tx_contexts); i++) {
 		if (priv->tx_contexts[i].echo_index == MAX_TX_URBS) {
@@ -1599,6 +1962,17 @@ static int kvaser_usb_probe(struct usb_interface *intf,
 	if (!dev)
 		return -ENOMEM;
 
+	if (LEAF_PRODUCT_ID(id->idProduct)) {
+		dev->family = KVASER_LEAF;
+	} else if (USBCAN_PRODUCT_ID(id->idProduct)) {
+		dev->family = KVASER_USBCAN;
+	} else {
+		dev_err(&intf->dev,
+			"Product ID (%d) does not belong to any known Kvaser USB family",
+			id->idProduct);
+		return -ENODEV;
+	}
+
 	err = kvaser_usb_get_endpoints(intf, &dev->bulk_in, &dev->bulk_out);
 	if (err) {
 		dev_err(&intf->dev, "Cannot get usb endpoint(s)");



  reply index

Thread overview: 95+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-12-23 15:46 [PATCH] can: kvaser_usb: Don't free packets when tight on URBs Ahmed S. Darwish
2014-12-23 15:53 ` [PATCH] can: kvaser_usb: Add support for the Usbcan-II family Ahmed S. Darwish
2014-12-24 12:36   ` Olivier Sobrie
2014-12-24 15:04     ` Ahmed S. Darwish
2014-12-28 21:51       ` Olivier Sobrie
2014-12-30 15:33         ` Ahmed S. Darwish
2014-12-31 12:13           ` Olivier Sobrie
2014-12-24 12:31 ` [PATCH] can: kvaser_usb: Don't free packets when tight on URBs Olivier Sobrie
2014-12-24 15:52   ` Ahmed S. Darwish
2014-12-24 23:56 ` [PATCH v2 1/4] " Ahmed S. Darwish
2014-12-24 23:59   ` [PATCH v2 2/4] can: kvaser_usb: Reset all URB tx contexts upon channel close Ahmed S. Darwish
2014-12-25  0:02     ` [PATCH v2 3/4] can: kvaser_usb: Don't send a RESET_CHIP for non-existing channels Ahmed S. Darwish
2014-12-25  0:04       ` [PATCH v2 4/4] can: kvaser_usb: Add support for the Usbcan-II family Ahmed S. Darwish
2014-12-28 21:54       ` [PATCH v2 3/4] can: kvaser_usb: Don't send a RESET_CHIP for non-existing channels Olivier Sobrie
2014-12-25  2:50   ` [PATCH v2 1/4] can: kvaser_usb: Don't free packets when tight on URBs Greg KH
2014-12-25  9:38     ` Ahmed S. Darwish
2014-12-28 21:52   ` Olivier Sobrie
2015-01-01 21:59 ` [PATCH] " Stephen Hemminger
2015-01-03 14:34   ` Ahmed S. Darwish
2015-01-05 17:49 ` [PATCH v3 1/4] " Ahmed S. Darwish
2015-01-05 17:52   ` [PATCH v3 2/4] can: kvaser_usb: Reset all URB tx contexts upon channel close Ahmed S. Darwish
2015-01-05 17:57     ` [PATCH v3 3/4] can: kvaser_usb: Don't send a RESET_CHIP for non-existing channels Ahmed S. Darwish
2015-01-05 18:31       ` Ahmed S. Darwish [this message]
2015-01-08 11:53         ` [PATCH v3 4/4] can: kvaser_usb: Add support for the Usbcan-II family Marc Kleine-Budde
2015-01-08 15:19           ` Ahmed S. Darwish
2015-01-12 11:51             ` Marc Kleine-Budde
2015-01-12 12:26               ` Ahmed S. Darwish
2015-01-12 12:34                 ` Marc Kleine-Budde
2015-01-09  3:06           ` Ahmed S. Darwish
2015-01-09 14:05             ` Marc Kleine-Budde
2015-01-08  9:59   ` [PATCH v3 1/4] can: kvaser_usb: Don't free packets when tight on URBs Marc Kleine-Budde
2015-01-11 20:05 ` [PATCH v4 00/04] can: Introduce support for Kvaser USBCAN-II devices Ahmed S. Darwish
2015-01-11 20:11   ` [PATCH v4 01/04] can: kvaser_usb: Don't dereference skb after a netif_rx() devices Ahmed S. Darwish
2015-01-11 20:15     ` [PATCH v4 2/4] can: kvaser_usb: Update error counters before exiting on OOM Ahmed S. Darwish
2015-01-11 20:36       ` [PATCH v4 3/4] can: kvaser_usb: Add support for the Usbcan-II family Ahmed S. Darwish
2015-01-11 20:45         ` [PATCH v4 4/4] can: kvaser_usb: Retry first bulk transfer on -ETIMEDOUT Ahmed S. Darwish
2015-01-11 20:51           ` Marc Kleine-Budde
2015-01-12 10:14             ` Ahmed S. Darwish
2015-01-12 10:25               ` Marc Kleine-Budde
2015-01-12 13:33               ` Olivier Sobrie
2015-01-12 13:50                 ` Ahmed S. Darwish
2015-01-12 11:20         ` [PATCH v4 3/4] can: kvaser_usb: Add support for the Usbcan-II family Ahmed S. Darwish
2015-01-12 11:43         ` Marc Kleine-Budde
2015-01-12 12:07           ` Ahmed S. Darwish
2015-01-12 12:36             ` Ahmed S. Darwish
2015-01-12 13:53         ` Olivier Sobrie
2015-01-18 20:12           ` Ahmed S. Darwish
2015-01-18 20:13             ` Marc Kleine-Budde
2015-01-12 11:09       ` [PATCH v4 2/4] can: kvaser_usb: Update error counters before exiting on OOM Marc Kleine-Budde
2015-01-12 20:36         ` Ahmed S. Darwish
2015-01-16 14:39           ` Marc Kleine-Budde
2015-01-11 20:49     ` [PATCH v4 01/04] can: kvaser_usb: Don't dereference skb after a netif_rx() Ahmed S. Darwish
2015-01-12 11:05       ` Marc Kleine-Budde
2015-01-20 21:44 ` [PATCH v5 1/5] can: kvaser_usb: Update net interface state before exiting on OOM Ahmed S. Darwish
2015-01-20 21:45   ` [PATCH v5 2/5] can: kvaser_usb: Consolidate and unify state change handling Ahmed S. Darwish
2015-01-20 21:47     ` [PATCH v5 3/5] can: kvaser_usb: Fix state handling upon BUS_ERROR events Ahmed S. Darwish
2015-01-20 21:48       ` [PATCH v5 4/5] can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT Ahmed S. Darwish
2015-01-20 21:50         ` [PATCH v5 5/5] can: kvaser_usb: Add support for the USBcan-II family Ahmed S. Darwish
2015-01-21 12:24         ` [PATCH v5 4/5] can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT Sergei Shtylyov
2015-01-25 11:59           ` Ahmed S. Darwish
2015-01-21 10:33     ` [PATCH v5 2/5] can: kvaser_usb: Consolidate and unify state change handling Andri Yngvason
2015-01-21 10:44       ` Marc Kleine-Budde
2015-01-21 11:00         ` Andri Yngvason
2015-01-21 11:53       ` Wolfgang Grandegger
2015-01-21 14:43         ` Ahmed S. Darwish
2015-01-21 15:00           ` Andri Yngvason
2015-01-21 15:36             ` Ahmed S. Darwish
2015-01-21 16:13               ` Wolfgang Grandegger
2015-01-23  6:07                 ` Ahmed S. Darwish
2015-01-23 10:32                   ` Andri Yngvason
2015-01-25  2:43                     ` Ahmed S. Darwish
2015-01-26 10:21                       ` Andri Yngvason
2015-01-21 16:37               ` Andri Yngvason
2015-01-21 16:20     ` Andri Yngvason
2015-01-21 22:59       ` Marc Kleine-Budde
2015-01-22 10:14         ` Andri Yngvason
2015-01-25  2:49           ` Ahmed S. Darwish
2015-01-25  3:21       ` Ahmed S. Darwish
2015-01-26  5:17 ` [PATCH v6 0/7] can: kvaser_usb: Leaf bugfixes and USBCan-II support Ahmed S. Darwish
2015-01-26  5:20   ` [PATCH v6 1/7] can: kvaser_usb: Do not sleep in atomic context Ahmed S. Darwish
2015-01-26  5:22     ` [PATCH v6 2/7] can: kvaser_usb: Send correct context to URB completion Ahmed S. Darwish
2015-01-26  5:24       ` [PATCH v6 3/7] can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT Ahmed S. Darwish
2015-01-26  5:25         ` [PATCH v6 4/7] can: kvaser_usb: Fix state handling upon BUS_ERROR events Ahmed S. Darwish
2015-01-26  5:27           ` [PATCH v6 5/7] can: kvaser_usb: Update interface state before exiting on OOM Ahmed S. Darwish
2015-01-26  5:29             ` [PATCH v6 6/7] can: kvaser_usb: Consolidate and unify state change handling Ahmed S. Darwish
2015-01-26  5:33               ` [PATCH v6 7/7] can: kvaser_usb: Add support for the USBcan-II family Ahmed S. Darwish
2015-01-26 10:34                 ` Andri Yngvason
2015-01-26 10:26               ` [PATCH v6 6/7] can: kvaser_usb: Consolidate and unify state change handling Andri Yngvason
2015-01-26 10:28             ` [PATCH v6 5/7] can: kvaser_usb: Update interface state before exiting on OOM Andri Yngvason
2015-01-26 10:50               ` Marc Kleine-Budde
2015-01-26 10:52                 ` Andri Yngvason
2015-01-26 10:53                   ` Marc Kleine-Budde
2015-01-26  9:55   ` [PATCH v6 0/7] can: kvaser_usb: Leaf bugfixes and USBCan-II support Marc Kleine-Budde
2015-01-26 10:07   ` Marc Kleine-Budde
2015-01-26 10:56     ` Marc Kleine-Budde

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20150105183131.GD6304@linux \
    --to=darwish.07@gmail.com \
    --cc=davem@davemloft.net \
    --cc=linux-can@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mkl@pengutronix.de \
    --cc=netdev@vger.kernel.org \
    --cc=olivier@sobrie.be \
    --cc=paul.gortmaker@windriver.com \
    --cc=socketcan@hartkopp.net \
    --cc=wg@grandegger.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

LKML Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lkml.kernel.org/lkml/0 lkml/git/0.git
	git clone --mirror https://lkml.kernel.org/lkml/1 lkml/git/1.git
	git clone --mirror https://lkml.kernel.org/lkml/2 lkml/git/2.git
	git clone --mirror https://lkml.kernel.org/lkml/3 lkml/git/3.git
	git clone --mirror https://lkml.kernel.org/lkml/4 lkml/git/4.git
	git clone --mirror https://lkml.kernel.org/lkml/5 lkml/git/5.git
	git clone --mirror https://lkml.kernel.org/lkml/6 lkml/git/6.git
	git clone --mirror https://lkml.kernel.org/lkml/7 lkml/git/7.git
	git clone --mirror https://lkml.kernel.org/lkml/8 lkml/git/8.git
	git clone --mirror https://lkml.kernel.org/lkml/9 lkml/git/9.git
	git clone --mirror https://lkml.kernel.org/lkml/10 lkml/git/10.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 lkml lkml/ https://lkml.kernel.org/lkml \
		linux-kernel@vger.kernel.org
	public-inbox-index lkml

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git