LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* Decrease boot time with AHCI drives?
@ 2018-04-04  9:53 Paul Menzel
  2018-04-04  9:57 ` Paul Menzel
  2018-04-05 14:34 ` Alan Cox
  0 siblings, 2 replies; 3+ messages in thread
From: Paul Menzel @ 2018-04-04  9:53 UTC (permalink / raw)
  To: Hans de Goede, Tejun Heo; +Cc: linux-ide, linux-kernel

[-- Attachment #1: Type: text/plain, Size: 4329 bytes --]

Dear Linux folks,


I am trying to decrease the boot time of the Linux kernel so the LUKS 
passphrase dialog (in the initrd) is shown as quickly as possible. The 
devices I test with is a Lenovo X60 and ASRock E350M1 both running with 
coreboot and the GRUB payload. The goal is to do this without having to 
rebuild a Linux kernel, but only by run-time

I am currently at 1.2 seconds.

```
[    0.610437] calling  ata_init+0x0/0x2be [libata] @ 88
[    0.610548] libata version 3.00 loaded.
[    0.610570] initcall ata_init+0x0/0x2be [libata] returned 0 after 107 
usecs
[    0.612100] calling  serio_raw_drv_init+0x0/0x1000 [serio_raw] @ 89
[    0.612132] initcall serio_raw_drv_init+0x0/0x1000 [serio_raw] 
returned 0 after 25 usecs
[    0.612659] calling  ahci_pci_driver_init+0x0/0x1000 [ahci] @ 88
[    0.612715] ahci 0000:00:1f.2: version 3.0
[    0.613050] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    0.613153] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 
Gbps 0x1 impl SATA mode
[    0.613239] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo 
pmp pio slum part
[    0.613915] calling  evdev_init+0x0/0x1000 [evdev] @ 85
[    0.614178] initcall evdev_init+0x0/0x1000 [evdev] returned 0 after 
250 usecs
[    0.624366] scsi host0: ahci
[    0.630638] scsi host1: ahci
[    0.640413] scsi host2: ahci
[    0.646559] scsi host3: ahci
[    0.646752] ata1: SATA max UDMA/133 abar m1024@0xe4445000 port 
0xe4445100 irq 28
[    0.646836] ata2: DUMMY
[    0.646902] ata3: DUMMY
[    0.646964] ata4: DUMMY
[    0.647098] initcall ahci_pci_driver_init+0x0/0x1000 [ahci] returned 
0 after 33619 usecs
[    1.124129] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.124605] ata1.00: ATA-9: M4-CT256M4SSD2, 070H, max UDMA/100
[    1.124674] ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 
31/32), AA
[    1.125179] ata1.00: configured for UDMA/100
[    1.125522] scsi 0:0:0:0: Direct-Access     ATA      M4-CT256M4SSD2 
070H PQ: 0 ANSI: 5
[    1.129127] calling  init_sd+0x0/0x1000 [sd_mod] @ 84
[    1.129268] initcall init_sd+0x0/0x1000 [sd_mod] returned 0 after 129 
usecs
[    1.129444] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 
GB/238 GiB)
[    1.129550] sd 0:0:0:0: [sda] Write Protect is off
[    1.129619] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.129647] sd 0:0:0:0: [sda] Write cache: enabled, read cache: 
enabled, doesn't support DPO or FUA
[    1.130384]  sda: sda1 sda2
[    1.131009] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.213492] calling  dm_init+0x0/0x31 [dm_mod] @ 110
[    1.213535] device-mapper: uevent: version 1.0.3
[    1.213727] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) 
initialised: dm-devel@redhat.com
[    1.213829] initcall dm_init+0x0/0x31 [dm_mod] returned 0 after 312 usecs
[    1.214434] calling  dm_crypt_init+0x0/0x1000 [dm_crypt] @ 110
[    1.214442] initcall dm_crypt_init+0x0/0x1000 [dm_crypt] returned 0 
after 2 usecs
```

So, according to `initcall_debug` the method `ahci_pci_driver_init` 
takes 33 ms to execute, which is longer then a few milliseconds.

But more importantly, it takes roughly half a second to set up the 
device. I understand, that the probing is part of AHCI(?), and in this 
case the Crucial m4 SSD drive/firmware is especially slow. So, I assume 
it will be hard to improve anything in the code to decrease the time.

That said, in my case the assumption is, that the device configuration 
will not change. That means, the drive will be the same and will be 
connected to the same port all the time.

Additionally, GRUB already probed the device to read the Linux kernel 
image and initrd image.

So, is there a way to avoid doing the probing twice or at all? That 
means, either cache the settings, and load them during boot by reading 
it from the firmware flash ROM chip, possible when using coreboot, and 
passing it to the Linux kernel for example by GRUB. That would also help 
with LinuxBoot [1], where the Linux kernel is used as the payload (boot 
kernel), already setting up the drive and kexec’s another Linux kernel, 
read from the drive.

Or, GRUB passes the settings it detected to the Linux kernel.


Kind regards,

Paul


[1] https://www.linuxboot.org/


[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/pkcs7-signature, Size: 5174 bytes --]

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2018-04-05 14:34 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-04-04  9:53 Decrease boot time with AHCI drives? Paul Menzel
2018-04-04  9:57 ` Paul Menzel
2018-04-05 14:34 ` Alan Cox

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).