LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Kishon Vijay Abraham I <kishon@ti.com>
To: Ulf Hansson <ulf.hansson@linaro.org>,
	Adrian Hunter <adrian.hunter@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>, <linux-mmc@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-omap@vger.kernel.org>, <kishon@ti.com>
Subject: [PATCH v5 14/14] mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode
Date: Fri, 27 Apr 2018 17:17:23 +0530	[thread overview]
Message-ID: <20180427114723.2687-15-kishon@ti.com> (raw)
In-Reply-To: <20180427114723.2687-1-kishon@ti.com>

commit 8d20b2eae6c47b095523 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 drivers/mmc/host/sdhci-omap.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index bd5e03d177e0..f3a7c8ece4be 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -842,8 +842,15 @@ static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
 
 	state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_1_8v", caps,
 						 MMC_CAP_1_8V_DDR);
-	if (!IS_ERR(state))
+	if (!IS_ERR(state)) {
 		pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+	} else {
+		state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_3_3v",
+							 caps,
+							 MMC_CAP_3_3V_DDR);
+		if (!IS_ERR(state))
+			pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+	}
 
 	state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs", caps,
 						 MMC_CAP_SD_HIGHSPEED);
-- 
2.17.0

  parent reply	other threads:[~2018-04-27 11:48 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-04-27 11:47 [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 01/14] mmc: sdhci-omap: Fix when capabilities are obtained from SDHCI_CAPABILITIES reg Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 02/14] mmc: sdhci-omap: Remove setting ADMA capability in driver Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 03/14] mmc: sdhci-omap: Workaround for Errata i843 Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 04/14] mmc: sdhci-omap: Invoke sdhci_get_of_property to read sdhci dt properties Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 05/14] mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't support 1.8v Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 06/14] mmc: sdhci: Add quirk to disable HW timeout Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 07/14] mmc: sdhci: Factor out target_timeout calculation Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 08/14] mmc: sdhci: Program a relatively accurate SW timeout value Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 09/14] mmc: sdhci-omap: Workaround for Errata i834 Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 10/14] dt-bindings: sdhci-omap: Add K2G specific binding Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 11/14] mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 12/14] mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 13/14] dt-bindings: sdhci-omap: Add pinctrl bindings Kishon Vijay Abraham I
2018-04-27 14:26   ` Rob Herring
2018-04-27 11:47 ` Kishon Vijay Abraham I [this message]
2018-05-02 13:15 ` [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support Ulf Hansson
2018-05-02 14:55   ` Tony Lindgren
2018-05-03  8:51     ` Ulf Hansson
2018-05-03 14:12       ` Tony Lindgren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180427114723.2687-15-kishon@ti.com \
    --to=kishon@ti.com \
    --cc=adrian.hunter@intel.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=ulf.hansson@linaro.org \
    --subject='Re: [PATCH v5 14/14] mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).