LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Marcin Ziemianowicz <marcin@ziemianowicz.com>
To: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>,
	Nicolas Ferre <nicolas.ferre@microchip.com>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3] clk: at91: PLL recalc_rate() now using cached MUL+DIV values
Date: Sun, 29 Apr 2018 11:25:12 -0400	[thread overview]
Message-ID: <20180429152512.GB742@hak8or> (raw)
In-Reply-To: <20180429151935.21df0784@bbrezillon>

On Sun, Apr 29, 2018 at 03:19:35PM +0200, Boris Brezillon wrote:
> On Sun, 29 Apr 2018 15:17:10 +0200
> Boris Brezillon <boris.brezillon@bootlin.com> wrote:
> 
> > Hi Marcin,
> > 
> > On Fri, 27 Apr 2018 13:56:09 -0400
> > Marcin Ziemianowicz <marcin@ziemianowicz.com> wrote:
> > 
> > > Stephen Boyd <sboyd@kernel.org>,
> > > linux-clk@vger.kernel.org,
> > > linux-arm-kernel@lists.infradead.org,
> > > linux-kernel@vger.kernel.org
> > > Bcc: 
> > > Subject: [PATCH v3] clk: at91: PLL recalc_rate() now using cached MUL and DIV
> > >  values
> > > Reply-To:  
> > 
> > Hm, I don't know how you prepared and sent your patch, but you shouldn't
> > have these fields in the body of your email. Please use git format-patch
> > to prepare the patch and then git send-email to send it.
> >  
> > > 
> > > When a USB device is connected to the USB host port on the SAM9N12 then
> > > you get "-62" error which seems to indicate USB replies from the device
> > > are timing out. Based on a logic sniffer, I saw the USB bus was running
> > > at half speed.
> > > 
> > > The PLL code uses cached MUL and DIV values which get set in set_rate()
> > > and applied in prepare(), but the recalc_rate() function instead
> > > queries the hardware instead of using these cached values. Therefore,
> > > if recalc_rate() is called between a set_rate() and prepare(), the
> > > wrong frequency is calculated and later the USB clock divider for the
> > > SAM9N12 SOC will be configured for an incorrect clock.
> > > 
> > > In my case, the PLL hardware was set to 96 Mhz before the OHCI
> > > driver loads, and therefore the usb clock divider was being set
> > > to /2 even though the OHCI driver set the PLL to 48 Mhz.
> > > 
> > > As an alternative explanation, I noticed this was fixed in the past:
> > > http://lists.infradead.org/pipermail/linux-arm-kernel/2014-September/283502.html
> > > but was later changed back via a large patch (maybe by mistake?):
> > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=1bdf02326b71eae7e9b4b335b881856aaf9d1af6  
> > 
> > Yep, probably by mistake. I started this rework long before it has been
> > submitted to the ML, so I probably messed something up when rebasing.
> > 
> > Also, prefer commit IDs to links to the ML archive. The above would
> > sentence would give:
> > 
> > "
> > As an alternative explanation, I noticed this was fixed in the past by
> > 87e2ed338f1b ("clk: at91: fix recalc_rate implementation of PLL
> > driver") but the bug was later re-introduced by 1bdf02326b71 ("clk:
> > at91: make use of syscon/regmap internally").
> > "
> > 
> > 
> > The following comment and the changelog should be placed after the
> > '---' line, so that it's not part of the commit message.
> > 
> > > Thank you for bearing with me about this Boris.
> > > 
> > > Changes since V2:
> > >   Removed all logging/debug messages I added  
> > >   > Comment by Boris Brezillon about my fix being wrong addressed    
> > > Changes since V1:
> > >   Added patch set cover letter
> > >   Shortened lines which were over >80 characters long  
> > >   > Comment by Greg Kroah-Hartman about "from" field in email addressed
> > >   > Comment by Alan Stern about redundant debug lines addressed    
> > >   
> > 
> > You should add Fixes and Cc-stable tags so that the fix is backported
> > to stable branches:
> > 
> > Fixes: 1bdf02326b71 ("clk: at91: make use of syscon/regmap internally)
> > Cc: <stable@vger.kernel.org>
> > 
> > > Signed-off-by: Marcin Ziemianowicz <marcin@ziemianowicz.com>
> > > ---
> > >  drivers/clk/at91/clk-pll.c | 13 +------------
> > >  1 file changed, 1 insertion(+), 12 deletions(-)
> > > 
> > > diff --git a/drivers/clk/at91/clk-pll.c b/drivers/clk/at91/clk-pll.c
> > > index 7d3223fc..cc6e0364 100644
> > > --- a/drivers/clk/at91/clk-pll.c
> > > +++ b/drivers/clk/at91/clk-pll.c
> > > @@ -132,19 +132,8 @@ static unsigned long clk_pll_recalc_rate(struct clk_hw *hw,
> > >  					 unsigned long parent_rate)
> > >  {
> > >  	struct clk_pll *pll = to_clk_pll(hw);
> > > -	unsigned int pllr;
> > > -	u16 mul;
> > > -	u8 div;
> > > -
> > > -	regmap_read(pll->regmap, PLL_REG(pll->id), &pllr);
> > > -
> > > -	div = PLL_DIV(pllr);
> > > -	mul = PLL_MUL(pllr, pll->layout);
> > > -
> > > -	if (!div || !mul)
> > > -		return 0;
> > >  
> > > -	return (parent_rate / div) * (mul + 1);
> > > +	return return (parent_rate / pll->div) * (pll->mul + 1);
> 
> Oops, one too many return as reported by kbuild test robot.

That's what I get for bug fixing in a buildroot generated kernel
directory and then copying it over to a new git clone'd kernel directory
by hand. I will fix this in addition to all the problems you raised in
the earlier email. Thank you again!

> 
> > 
> > The fix looks good. Let me know if you struggle with git
> > format-patch/send-email and I'll try to help you (or send the patch for
> > you if you don't care learning the process, but I think it's better if
> > you learn how to submit patches).
> > 
> > Thanks,
> > 
> > Boris
> > 
> > >  }
> > >  
> > >  static long clk_pll_get_best_div_mul(struct clk_pll *pll, unsigned long rate,  
> > 
> 

  reply	other threads:[~2018-04-29 15:25 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-04-27 17:56 Marcin Ziemianowicz
2018-04-29 10:59 ` kbuild test robot
2018-04-29 13:17 ` Boris Brezillon
2018-04-29 13:19   ` Boris Brezillon
2018-04-29 15:25     ` Marcin Ziemianowicz [this message]
2018-04-29 15:22   ` Marcin Ziemianowicz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180429152512.GB742@hak8or \
    --to=marcin@ziemianowicz.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=boris.brezillon@bootlin.com \
    --cc=boris.brezillon@free-electrons.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mturquette@baylibre.com \
    --cc=nicolas.ferre@microchip.com \
    --cc=sboyd@kernel.org \
    --subject='Re: [PATCH v3] clk: at91: PLL recalc_rate() now using cached MUL+DIV values' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).