LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support
@ 2018-06-11 20:52 Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm Stefan Agner
                   ` (5 more replies)
  0 siblings, 6 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

The most notable change in this forth revision is the addition of
raw page and oob read/write accessors which support DMA. After
looking a bit closer into the U-Boot implementation of the Tegra
NAND driver I realized that in my previous attempts I enabled
SKIP_SPARE_EN which seems not to work when not using ECC modes.

A bad block scan of a 1GiB chip dropped from 3.9s to 0.2s.

The MTD kernel module tests seem to pass still:

=================================================
mtd_speedtest: MTD device: 4
mtd_speedtest: MTD device size 1068498944, eraseblock size 262144, page size 4096, count of eraseblocks 4076, pages per eraseblock 64, OOB size 224
mtd_test: scanning for bad eraseblocks
mtd_test: block 4072 is bad
mtd_test: block 4073 is bad
mtd_test: block 4074 is bad
mtd_test: block 4075 is bad
mtd_test: scanned 4076 eraseblocks, 4 are bad
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 11499 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 15251 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 9588 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 15213 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 10291 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 15416 KiB/s
mtd_speedtest: Testing erase speed
mtd_speedtest: erase speed is 128000 KiB/s
mtd_speedtest: Testing 2x multi-block erase speed
mtd_speedtest: 2x multi-block erase speed is 333364 KiB/s
mtd_speedtest: Testing 4x multi-block erase speed
mtd_speedtest: 4x multi-block erase speed is 335187 KiB/s
mtd_speedtest: Testing 8x multi-block erase speed
mtd_speedtest: 8x multi-block erase speed is 345061 KiB/s
mtd_speedtest: Testing 16x multi-block erase speed
mtd_speedtest: 16x multi-block erase speed is 344264 KiB/s
mtd_speedtest: Testing 32x multi-block erase speed
mtd_speedtest: 32x multi-block erase speed is 347941 KiB/s
mtd_speedtest: Testing 64x multi-block erase speed
mtd_speedtest: 64x multi-block erase speed is 348522 KiB/s
mtd_speedtest: finished
=================================================

==================================================
mtd_nandbiterrs: MTD device: 3
mtd_nandbiterrs: MTD device size 1048576, eraseblock=262144, page=4096, oob=224
mtd_nandbiterrs: Device uses 1 subpages of 4096 bytes
mtd_nandbiterrs: Using page=0, offset=0, eraseblock=0
mtd_nandbiterrs: incremental biterrors test
mtd_nandbiterrs: write_page
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 0 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 0/5
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 1 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 1 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 0/2
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 2 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 2 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 0/0
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 3 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 3 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 1/7
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 4 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 4 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 1/5
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 5 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 5 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 1/2
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 6 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 6 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 1/0
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 7 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 7 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 2/6
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 8 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 8 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 2/5
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 9 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 9 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 2/2
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 10 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 10 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 2/0
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 11 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 11 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 3/7
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 12 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 12 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 3/6
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 13 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 13 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 3/5
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 14 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 14 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 3/2
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 15 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 15 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 3/0
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: Read reported 16 corrected bit errors
mtd_nandbiterrs: verify_page
mtd_nandbiterrs: Successfully corrected 16 bit errors per subpage
mtd_nandbiterrs: Inserted biterror @ 4/2
mtd_nandbiterrs: rewrite page
mtd_nandbiterrs: read_page
mtd_nandbiterrs: error: read failed at 0x0
mtd_nandbiterrs: After 17 biterrors per subpage, read reported error -74
mtd_nandbiterrs: finished successfully.
==================================================

==================================================
mtd_nandbiterrs: MTD device: 3
mtd_nandbiterrs: MTD device size 1048576, eraseblock=262144, page=4096, oob=224
mtd_nandbiterrs: Device uses 1 subpages of 4096 bytes
mtd_nandbiterrs: Using page=0, offset=0, eraseblock=0
mtd_nandbiterrs: overwrite biterrors test
mtd_nandbiterrs: write_page
mtd_nandbiterrs: Read reported 1 corrected bit errors
mtd_nandbiterrs: Read reported 2 corrected bit errors
mtd_nandbiterrs: Read reported 3 corrected bit errors
mtd_nandbiterrs: Read reported 4 corrected bit errors
mtd_nandbiterrs: Read reported 5 corrected bit errors
mtd_nandbiterrs: Read reported 8 corrected bit errors
mtd_nandbiterrs: Read reported 10 corrected bit errors
mtd_nandbiterrs: Read reported 12 corrected bit errors
mtd_nandbiterrs: Read reported 14 corrected bit errors
mtd_nandbiterrs: Read reported 21 corrected bit errors
mtd_nandbiterrs: Read reported 28 corrected bit errors
mtd_nandbiterrs: Read reported 32 corrected bit errors
mtd_nandbiterrs: Read reported 40 corrected bit errors
mtd_nandbiterrs: Read reported 48 corrected bit errors
mtd_nandbiterrs: Read reported 56 corrected bit errors
mtd_nandbiterrs: Read reported 64 corrected bit errors
mtd_nandbiterrs: Read reported 72 corrected bit errors
mtd_nandbiterrs: Read reported 80 corrected bit errors
mtd_nandbiterrs: Read reported 88 corrected bit errors
mtd_nandbiterrs: Read reported 96 corrected bit errors
mtd_nandbiterrs: Read reported 104 corrected bit errors
mtd_nandbiterrs: Read reported 112 corrected bit errors
mtd_nandbiterrs: error: read failed at 0x0
mtd_nandbiterrs: Read reported error -74
mtd_nandbiterrs: Bit error histogram (2209 operations total):
mtd_nandbiterrs: Page reads with   0 corrected bit errors: 977
mtd_nandbiterrs: Page reads with   1 corrected bit errors: 92
mtd_nandbiterrs: Page reads with   2 corrected bit errors: 81
mtd_nandbiterrs: Page reads with   3 corrected bit errors: 7
mtd_nandbiterrs: Page reads with   4 corrected bit errors: 4
mtd_nandbiterrs: Page reads with   5 corrected bit errors: 3
mtd_nandbiterrs: Page reads with   6 corrected bit errors: 0
mtd_nandbiterrs: Page reads with   7 corrected bit errors: 0
mtd_nandbiterrs: Page reads with   8 corrected bit errors: 9
mtd_nandbiterrs: Page reads with   9 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  10 corrected bit errors: 42
mtd_nandbiterrs: Page reads with  11 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  12 corrected bit errors: 24
mtd_nandbiterrs: Page reads with  13 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  14 corrected bit errors: 62
mtd_nandbiterrs: Page reads with  15 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  16 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  17 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  18 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  19 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  20 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  21 corrected bit errors: 15
mtd_nandbiterrs: Page reads with  22 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  23 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  24 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  25 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  26 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  27 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  28 corrected bit errors: 75
mtd_nandbiterrs: Page reads with  29 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  30 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  31 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  32 corrected bit errors: 148
mtd_nandbiterrs: Page reads with  33 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  34 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  35 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  36 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  37 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  38 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  39 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  40 corrected bit errors: 74
mtd_nandbiterrs: Page reads with  41 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  42 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  43 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  44 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  45 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  46 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  47 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  48 corrected bit errors: 37
mtd_nandbiterrs: Page reads with  49 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  50 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  51 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  52 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  53 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  54 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  55 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  56 corrected bit errors: 93
mtd_nandbiterrs: Page reads with  57 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  58 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  59 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  60 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  61 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  62 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  63 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  64 corrected bit errors: 23
mtd_nandbiterrs: Page reads with  65 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  66 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  67 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  68 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  69 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  70 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  71 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  72 corrected bit errors: 258
mtd_nandbiterrs: Page reads with  73 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  74 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  75 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  76 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  77 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  78 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  79 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  80 corrected bit errors: 90
mtd_nandbiterrs: Page reads with  81 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  82 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  83 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  84 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  85 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  86 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  87 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  88 corrected bit errors: 14
mtd_nandbiterrs: Page reads with  89 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  90 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  91 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  92 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  93 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  94 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  95 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  96 corrected bit errors: 21
mtd_nandbiterrs: Page reads with  97 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  98 corrected bit errors: 0
mtd_nandbiterrs: Page reads with  99 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 100 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 101 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 102 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 103 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 104 corrected bit errors: 32
mtd_nandbiterrs: Page reads with 105 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 106 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 107 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 108 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 109 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 110 corrected bit errors: 0
mtd_nandbiterrs: Page reads with 111 corrected bit errors: 0
mtd_nandbiterrs: finished successfully.
==================================================

=================================================
mtd_oobtest: MTD device: 3
mtd_oobtest: MTD device size 1048576, eraseblock size 262144, page size 4096, count of eraseblocks 4, pages per eraseblock 64, OOB size 224
mtd_test: scanning for bad eraseblocks
mtd_test: scanned 4 eraseblocks, 0 are bad
mtd_oobtest: test 1 of 5
mtd_oobtest: writing OOBs of whole device
mtd_oobtest: written up to eraseblock 0
mtd_oobtest: written 4 eraseblocks
mtd_oobtest: verifying all eraseblocks
mtd_oobtest: verified up to eraseblock 0
mtd_oobtest: verified 4 eraseblocks
mtd_oobtest: test 2 of 5
mtd_oobtest: writing OOBs of whole device
mtd_oobtest: written up to eraseblock 0
mtd_oobtest: written 4 eraseblocks
mtd_oobtest: verifying all eraseblocks
mtd_oobtest: verified up to eraseblock 0
mtd_oobtest: verified 4 eraseblocks
mtd_oobtest: test 3 of 5
mtd_oobtest: writing OOBs of whole device
mtd_oobtest: written up to eraseblock 0
mtd_oobtest: written 4 eraseblocks
mtd_oobtest: verifying all eraseblocks
mtd_oobtest: verified up to eraseblock 0
mtd_oobtest: verified 4 eraseblocks
mtd_oobtest: test 4 of 5
mtd_oobtest: attempting to start write past end of OOB
mtd_oobtest: an error is expected...
mtd_oobtest: error occurred as expected
mtd_oobtest: attempting to start read past end of OOB
mtd_oobtest: an error is expected...
mtd_oobtest: error occurred as expected
mtd_oobtest: attempting to write past end of device
mtd_oobtest: an error is expected...
mtd_oobtest: error occurred as expected
mtd_oobtest: attempting to read past end of device
mtd_oobtest: an error is expected...
mtd_oobtest: error occurred as expected
mtd_oobtest: attempting to write past end of device
mtd_oobtest: an error is expected...
mtd_oobtest: error occurred as expected
mtd_oobtest: attempting to read past end of device
mtd_oobtest: an error is expected...
mtd_oobtest: error occurred as expected
mtd_oobtest: test 5 of 5
mtd_oobtest: writing OOBs of whole device
mtd_oobtest: written up to eraseblock 0
mtd_oobtest: written up to eraseblock 0
mtd_oobtest: written 3 eraseblocks
mtd_oobtest: verifying all eraseblocks
mtd_oobtest: verified up to eraseblock 0
mtd_oobtest: verified 3 eraseblocks
mtd_oobtest: finished with 0 errors
=================================================

=================================================
mtd_readtest: MTD device: 3
mtd_readtest: MTD device size 1048576, eraseblock size 262144, page size 4096, count of eraseblocks 4, pages per eraseblock 64, OOB size 224
mtd_test: scanning for bad eraseblocks
mtd_test: scanned 4 eraseblocks, 0 are bad
mtd_readtest: testing page read
mtd_readtest: finished
=================================================

=================================================
mtd_subpagetest: MTD device: 3
mtd_subpagetest: MTD device size 1048576, eraseblock size 262144, page size 4096, subpage size 4096, count of eraseblocks 4, pages per eraseblock 64, OOB size 224
mtd_test: scanning for bad eraseblocks
mtd_test: scanned 4 eraseblocks, 0 are bad
mtd_subpagetest: writing whole device
mtd_subpagetest: written up to eraseblock 0
mtd_subpagetest: written 4 eraseblocks
mtd_subpagetest: verifying all eraseblocks
mtd_subpagetest: verified up to eraseblock 0
mtd_subpagetest: verified 4 eraseblocks
mtd_subpagetest: verifying all eraseblocks for 0xff
mtd_subpagetest: verified up to eraseblock 0
mtd_subpagetest: verified 4 eraseblocks
mtd_subpagetest: writing whole device
mtd_subpagetest: written up to eraseblock 0
mtd_subpagetest: written 4 eraseblocks
mtd_subpagetest: verifying all eraseblocks
mtd_subpagetest: verified up to eraseblock 0
mtd_subpagetest: verified 4 eraseblocks
mtd_subpagetest: verifying all eraseblocks for 0xff
mtd_subpagetest: verified up to eraseblock 0
mtd_subpagetest: verified 4 eraseblocks
mtd_subpagetest: finished with 0 errors
=================================================

=================================================
mtd_stresstest: MTD device: 3
mtd_stresstest: MTD device size 1048576, eraseblock size 262144, page size 4096, count of eraseblocks 4, pages per eraseblock 64, OOB size 224
mtd_test: scanning for bad eraseblocks
mtd_test: scanned 4 eraseblocks, 0 are bad
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_stresstest: 1024 operations done
mtd_stresstest: 2048 operations done
mtd_stresstest: 3072 operations done
mtd_stresstest: 4096 operations done
mtd_stresstest: 5120 operations done
mtd_stresstest: aborting test due to pending signal!
mtd_stresstest: error -4 occurred
=================================================

--
Stefan

Changes since v1:
- Split controller and NAND chip structure
- Add BCH support
- Allow to select algorithm and strength using device tree
- Improve HW ECC error reporting and use DEC_STATUS_BUF only
- Use SPDX license identifier
- Use per algorithm mtd_ooblayout_ops
- Use setup_data_interface callback for NAND timing configuration

Changes since v2:
- Set clock rate using assigned-clocks
- Use BIT() macro
- Fix and improve timing calculation
- Improve ECC error handling
- Store OOB layout for tag area in Tegra chip structure
- Update/fix bindings
- Use more specific variable names (replace "value")
- Introduce nand-is-boot-medium
- Choose sensible ECC strenght automatically
- Use wait_for_completion_timeout
- Print register dump on completion timeout
- Unify tegra_nand_(read|write)_page in tegra_nand_page_xfer

Changes since v3:
- Implement tegra_nand_(read|write)_raw using DMA
- Implement tegra_nand_(read|write)_oob using DMA
- Name registers according to Tegra 2 Technical Reference Manual (v02p)
- Use wait_for_completion_io_timeout to account for IO
- Get chip select id from device tree reg property
- Clear interrupts and reinit wait queues in case command/DMA times out
- Set default MTD name after nand_set_flash_node
- Move MODULE_DEVICE_TABLE after declaration of tegra_nand_of_match
- Make (rs|bch)_strength static

Lucas Stach (1):
  ARM: dts: tegra: add Tegra20 NAND flash controller node

Stefan Agner (5):
  mtd: rawnand: add Reed-Solomon error correction algorithm
  mtd: rawnand: add an option to specify NAND chip as a boot device
  mtd: rawnand: tegra: add devicetree binding
  mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  ARM: dts: tegra: enable NAND flash on Colibri T20

 .../devicetree/bindings/mtd/nand.txt          |    6 +-
 .../bindings/mtd/nvidia-tegra20-nand.txt      |   64 +
 MAINTAINERS                                   |    7 +
 arch/arm/boot/dts/tegra20-colibri-512.dtsi    |   16 +
 arch/arm/boot/dts/tegra20.dtsi                |   15 +
 drivers/mtd/nand/raw/Kconfig                  |    6 +
 drivers/mtd/nand/raw/Makefile                 |    1 +
 drivers/mtd/nand/raw/nand_base.c              |    4 +
 drivers/mtd/nand/raw/tegra_nand.c             | 1248 +++++++++++++++++
 include/linux/mtd/rawnand.h                   |    7 +
 10 files changed, 1373 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
 create mode 100644 drivers/mtd/nand/raw/tegra_nand.c

-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm
  2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
@ 2018-06-11 20:52 ` Stefan Agner
  2018-06-12 18:37   ` Rob Herring
  2018-06-11 20:52 ` [PATCH v4 2/6] mtd: rawnand: add an option to specify NAND chip as a boot device Stefan Agner
                   ` (4 subsequent siblings)
  5 siblings, 1 reply; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

Add Reed-Solomon (RS) to the enumeration of ECC algorithms.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
---
 Documentation/devicetree/bindings/mtd/nand.txt | 2 +-
 drivers/mtd/nand/raw/nand_base.c               | 1 +
 include/linux/mtd/rawnand.h                    | 1 +
 3 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
index 8bb11d809429..eaef8c657aa5 100644
--- a/Documentation/devicetree/bindings/mtd/nand.txt
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -25,7 +25,7 @@ Optional NAND chip properties:
 		  Deprecated values:
 		  "soft_bch": use "soft" and nand-ecc-algo instead
 - nand-ecc-algo: string, algorithm of NAND ECC.
-		 Supported values are: "hamming", "bch".
+		 Valid values are: "hamming", "bch", "rs".
 - nand-bus-width : 8 or 16 bus width if not present 8
 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
 
diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index f28c3a555861..9eb5678dd6d0 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -5744,6 +5744,7 @@ static int of_get_nand_ecc_mode(struct device_node *np)
 static const char * const nand_ecc_algos[] = {
 	[NAND_ECC_HAMMING]	= "hamming",
 	[NAND_ECC_BCH]		= "bch",
+	[NAND_ECC_RS]		= "rs",
 };
 
 static int of_get_nand_ecc_algo(struct device_node *np)
diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 5dad59b31244..6a82da8c44ce 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -114,6 +114,7 @@ enum nand_ecc_algo {
 	NAND_ECC_UNKNOWN,
 	NAND_ECC_HAMMING,
 	NAND_ECC_BCH,
+	NAND_ECC_RS,
 };
 
 /*
-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 2/6] mtd: rawnand: add an option to specify NAND chip as a boot device
  2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm Stefan Agner
@ 2018-06-11 20:52 ` Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 3/6] mtd: rawnand: tegra: add devicetree binding Stefan Agner
                   ` (3 subsequent siblings)
  5 siblings, 0 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
---
 Documentation/devicetree/bindings/mtd/nand.txt | 4 ++++
 drivers/mtd/nand/raw/nand_base.c               | 3 +++
 include/linux/mtd/rawnand.h                    | 6 ++++++
 3 files changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
index eaef8c657aa5..e949c778e983 100644
--- a/Documentation/devicetree/bindings/mtd/nand.txt
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -43,6 +43,10 @@ Optional NAND chip properties:
 		     This is particularly useful when only the in-band area is
 		     used by the upper layers, and you want to make your NAND
 		     as reliable as possible.
+- nand-is-boot-medium: Whether the NAND chip is a boot medium. Drivers might use
+		       this information to select ECC algorithms supported by
+		       the boot ROM or similar restrictions.
+
 - nand-rb: shall contain the native Ready/Busy ids.
 
 The ECC strength and ECC step size properties define the correction capability
diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index 9eb5678dd6d0..c8fb7c9855e2 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -5826,6 +5826,9 @@ static int nand_dt_init(struct nand_chip *chip)
 	if (of_get_nand_bus_width(dn) == 16)
 		chip->options |= NAND_BUSWIDTH_16;
 
+	if (of_property_read_bool(dn, "nand-is-boot-medium"))
+		chip->options |= NAND_IS_BOOT_MEDIUM;
+
 	if (of_get_nand_on_flash_bbt(dn))
 		chip->bbt_options |= NAND_BBT_USE_FLASH;
 
diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 6a82da8c44ce..8e54fcf2fa94 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -212,6 +212,12 @@ enum nand_ecc_algo {
  */
 #define NAND_WAIT_TCCS		0x00200000
 
+/*
+ * Whether the NAND chip is a boot medium. Drivers might use this information
+ * to select ECC algorithms supported by the boot ROM or similar restrictions.
+ */
+#define NAND_IS_BOOT_MEDIUM	0x00400000
+
 /* Options set by nand scan */
 /* Nand scan has allocated controller struct */
 #define NAND_CONTROLLER_ALLOC	0x80000000
-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 3/6] mtd: rawnand: tegra: add devicetree binding
  2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 2/6] mtd: rawnand: add an option to specify NAND chip as a boot device Stefan Agner
@ 2018-06-11 20:52 ` Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
                   ` (2 subsequent siblings)
  5 siblings, 0 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

This adds the devicetree binding for the Tegra 2 NAND flash
controller.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/mtd/nvidia-tegra20-nand.txt      | 64 +++++++++++++++++++
 1 file changed, 64 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt

diff --git a/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
new file mode 100644
index 000000000000..1c351362f3a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
@@ -0,0 +1,64 @@
+NVIDIA Tegra NAND Flash controller
+
+Required properties:
+- compatible: Must be one of:
+  - "nvidia,tegra20-nand"
+- reg: MMIO address range
+- interrupts: interrupt output of the NFC controller
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - nand
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - nand
+
+Optional children nodes:
+Individual NAND chips are children of the NAND controller node. Currently
+only one NAND chip supported.
+
+Required children node properties:
+- reg: An integer ranging from 1 to 6 representing the CS line to use.
+
+Optional children node properties:
+- nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only
+		 "hw" is supported.
+- nand-ecc-algo: string, algorithm of NAND ECC.
+		 Supported values with "hw" ECC mode are: "rs", "bch".
+- nand-bus-width : See nand.txt
+- nand-on-flash-bbt: See nand.txt
+- nand-ecc-strength: integer representing the number of bits to correct
+		     per ECC step (always 512). Supported strength using HW ECC
+		     modes are:
+		     - RS: 4, 6, 8
+		     - BCH: 4, 8, 14, 16
+- nand-ecc-maximize: See nand.txt
+- nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM
+		       are choosen.
+- wp-gpios: GPIO specifier for the write protect pin.
+
+Optional child node of NAND chip nodes:
+Partitions: see partition.txt
+
+  Example:
+	nand-controller@70008000 {
+		compatible = "nvidia,tegra20-nand";
+		reg = <0x70008000 0x100>;
+		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
+		clock-names = "nand";
+		resets = <&tegra_car 13>;
+		reset-names = "nand";
+
+		nand@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			nand-bus-width = <8>;
+			nand-on-flash-bbt;
+			nand-ecc-algo = "bch";
+			nand-ecc-strength = <8>;
+			wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>;
+		};
+	};
-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
                   ` (2 preceding siblings ...)
  2018-06-11 20:52 ` [PATCH v4 3/6] mtd: rawnand: tegra: add devicetree binding Stefan Agner
@ 2018-06-11 20:52 ` Stefan Agner
  2018-06-11 23:08   ` kbuild test robot
                     ` (3 more replies)
  2018-06-11 20:52 ` [PATCH v4 5/6] ARM: dts: tegra: add Tegra20 NAND flash controller node Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 6/6] ARM: dts: tegra: enable NAND flash on Colibri T20 Stefan Agner
  5 siblings, 4 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

Add support for the NAND flash controller found on NVIDIA
Tegra 2 SoCs. This implementation does not make use of the
command queue feature. Regular operations/data transfers are
done in PIO mode. Page read/writes with hardware ECC make
use of the DMA for data transfer.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 MAINTAINERS                       |    7 +
 drivers/mtd/nand/raw/Kconfig      |    6 +
 drivers/mtd/nand/raw/Makefile     |    1 +
 drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
 4 files changed, 1262 insertions(+)
 create mode 100644 drivers/mtd/nand/raw/tegra_nand.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 58b9861ccf99..c2e5571c85d4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13844,6 +13844,13 @@ M:	Laxman Dewangan <ldewangan@nvidia.com>
 S:	Supported
 F:	drivers/input/keyboard/tegra-kbc.c
 
+TEGRA NAND DRIVER
+M:	Stefan Agner <stefan@agner.ch>
+M:	Lucas Stach <dev@lynxeye.de>
+S:	Maintained
+F:	Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
+F:	drivers/mtd/nand/raw/tegra_nand.c
+
 TEGRA PWM DRIVER
 M:	Thierry Reding <thierry.reding@gmail.com>
 S:	Supported
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 19a2b283fbbe..e9093f52371e 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -534,4 +534,10 @@ config MTD_NAND_MTK
 	  Enables support for NAND controller on MTK SoCs.
 	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
 
+config MTD_NAND_TEGRA
+	tristate "Support for NAND controller on NVIDIA Tegra"
+	depends on ARCH_TEGRA || COMPILE_TEST
+	help
+	  Enables support for NAND flash controller on NVIDIA Tegra SoC.
+
 endif # MTD_NAND
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
index 165b7ef9e9a1..d5a5f9832b88 100644
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
 obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
 obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
+obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
 
 nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
 nand-objs += nand_amd.o
diff --git a/drivers/mtd/nand/raw/tegra_nand.c b/drivers/mtd/nand/raw/tegra_nand.c
new file mode 100644
index 000000000000..dd23a5eb6af3
--- /dev/null
+++ b/drivers/mtd/nand/raw/tegra_nand.c
@@ -0,0 +1,1248 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Stefan Agner <stefan@agner.ch>
+ * Copyright (C) 2014-2015 Lucas Stach <dev@lynxeye.de>
+ * Copyright (C) 2012 Avionic Design GmbH
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+#define COMMAND					0x00
+#define   COMMAND_GO				BIT(31)
+#define   COMMAND_CLE				BIT(30)
+#define   COMMAND_ALE				BIT(29)
+#define   COMMAND_PIO				BIT(28)
+#define   COMMAND_TX				BIT(27)
+#define   COMMAND_RX				BIT(26)
+#define   COMMAND_SEC_CMD			BIT(25)
+#define   COMMAND_AFT_DAT			BIT(24)
+#define   COMMAND_TRANS_SIZE(x)			(((x - 1) & 0xf) << 20)
+#define   COMMAND_A_VALID			BIT(19)
+#define   COMMAND_B_VALID			BIT(18)
+#define   COMMAND_RD_STATUS_CHK			BIT(17)
+#define   COMMAND_RBSY_CHK			BIT(16)
+#define   COMMAND_CE(x)				BIT(8 + ((x) & 0x7))
+#define   COMMAND_CLE_SIZE(x)			(((x - 1) & 0x3) << 4)
+#define   COMMAND_ALE_SIZE(x)			(((x - 1) & 0xf) << 0)
+
+#define STATUS					0x04
+
+#define ISR					0x08
+#define   ISR_CORRFAIL_ERR			BIT(24)
+#define   ISR_UND				BIT(7)
+#define   ISR_OVR				BIT(6)
+#define   ISR_CMD_DONE				BIT(5)
+#define   ISR_ECC_ERR				BIT(4)
+
+#define IER					0x0c
+#define   IER_ERR_TRIG_VAL(x)			(((x) & 0xf) << 16)
+#define   IER_UND				BIT(7)
+#define   IER_OVR				BIT(6)
+#define   IER_CMD_DONE				BIT(5)
+#define   IER_ECC_ERR				BIT(4)
+#define   IER_GIE				BIT(0)
+
+#define CONFIG					0x10
+#define   CONFIG_HW_ECC				BIT(31)
+#define   CONFIG_ECC_SEL			BIT(30)
+#define   CONFIG_ERR_COR			BIT(29)
+#define   CONFIG_PIPE_EN			BIT(28)
+#define   CONFIG_TVAL_4				(0 << 24)
+#define   CONFIG_TVAL_6				(1 << 24)
+#define   CONFIG_TVAL_8				(2 << 24)
+#define   CONFIG_SKIP_SPARE			BIT(23)
+#define   CONFIG_BUS_WIDTH_16			BIT(21)
+#define   CONFIG_COM_BSY			BIT(20)
+#define   CONFIG_PS_256				(0 << 16)
+#define   CONFIG_PS_512				(1 << 16)
+#define   CONFIG_PS_1024			(2 << 16)
+#define   CONFIG_PS_2048			(3 << 16)
+#define   CONFIG_PS_4096			(4 << 16)
+#define   CONFIG_SKIP_SPARE_SIZE_4		(0 << 14)
+#define   CONFIG_SKIP_SPARE_SIZE_8		(1 << 14)
+#define   CONFIG_SKIP_SPARE_SIZE_12		(2 << 14)
+#define   CONFIG_SKIP_SPARE_SIZE_16		(3 << 14)
+#define   CONFIG_TAG_BYTE_SIZE(x)			((x) & 0xff)
+
+#define TIMING_1				0x14
+#define   TIMING_TRP_RESP(x)			(((x) & 0xf) << 28)
+#define   TIMING_TWB(x)				(((x) & 0xf) << 24)
+#define   TIMING_TCR_TAR_TRR(x)			(((x) & 0xf) << 20)
+#define   TIMING_TWHR(x)			(((x) & 0xf) << 16)
+#define   TIMING_TCS(x)				(((x) & 0x3) << 14)
+#define   TIMING_TWH(x)				(((x) & 0x3) << 12)
+#define   TIMING_TWP(x)				(((x) & 0xf) <<  8)
+#define   TIMING_TRH(x)				(((x) & 0x3) <<  4)
+#define   TIMING_TRP(x)				(((x) & 0xf) <<  0)
+
+#define RESP					0x18
+
+#define TIMING_2				0x1c
+#define   TIMING_TADL(x)			((x) & 0xf)
+
+#define CMD_REG1				0x20
+#define CMD_REG2				0x24
+#define ADDR_REG1				0x28
+#define ADDR_REG2				0x2c
+
+#define DMA_MST_CTRL				0x30
+#define   DMA_MST_CTRL_GO			BIT(31)
+#define   DMA_MST_CTRL_IN			(0 << 30)
+#define   DMA_MST_CTRL_OUT			BIT(30)
+#define   DMA_MST_CTRL_PERF_EN			BIT(29)
+#define   DMA_MST_CTRL_IE_DONE			BIT(28)
+#define   DMA_MST_CTRL_REUSE			BIT(27)
+#define   DMA_MST_CTRL_BURST_1			(2 << 24)
+#define   DMA_MST_CTRL_BURST_4			(3 << 24)
+#define   DMA_MST_CTRL_BURST_8			(4 << 24)
+#define   DMA_MST_CTRL_BURST_16			(5 << 24)
+#define   DMA_MST_CTRL_IS_DONE			BIT(20)
+#define   DMA_MST_CTRL_EN_A			BIT(2)
+#define   DMA_MST_CTRL_EN_B			BIT(1)
+
+#define DMA_CFG_A				0x34
+#define DMA_CFG_B				0x38
+
+#define FIFO_CTRL				0x3c
+#define   FIFO_CTRL_CLR_ALL			BIT(3)
+
+#define DATA_PTR				0x40
+#define TAG_PTR					0x44
+#define ECC_PTR					0x48
+
+#define DEC_STATUS				0x4c
+#define   DEC_STATUS_A_ECC_FAIL			BIT(1)
+#define   DEC_STATUS_ERR_COUNT_MASK		0x00ff0000
+#define   DEC_STATUS_ERR_COUNT_SHIFT		16
+
+#define HWSTATUS_CMD				0x50
+#define HWSTATUS_MASK				0x54
+#define   HWSTATUS_RDSTATUS_MASK(x)		(((x) & 0xff) << 24)
+#define   HWSTATUS_RDSTATUS_VALUE(x)		(((x) & 0xff) << 16)
+#define   HWSTATUS_RBSY_MASK(x)			(((x) & 0xff) << 8)
+#define   HWSTATUS_RBSY_VALUE(x)		(((x) & 0xff) << 0)
+
+#define BCH_CONFIG				0xcc
+#define   BCH_ENABLE				BIT(0)
+#define   BCH_TVAL_4				(0 << 4)
+#define   BCH_TVAL_8				(1 << 4)
+#define   BCH_TVAL_14				(2 << 4)
+#define   BCH_TVAL_16				(3 << 4)
+
+#define DEC_STAT_RESULT				0xd0
+#define DEC_STAT_BUF				0xd4
+#define   DEC_STAT_BUF_FAIL_SEC_FLAG_MASK	0xff000000
+#define   DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT	24
+#define   DEC_STAT_BUF_CORR_SEC_FLAG_MASK	0x00ff0000
+#define   DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT	16
+#define   DEC_STAT_BUF_MAX_CORR_CNT_MASK	0x00001f00
+#define   DEC_STAT_BUF_MAX_CORR_CNT_SHIFT	8
+
+#define OFFSET(val, off)	((val) < (off) ? 0 : (val) - (off))
+
+#define SKIP_SPARE_BYTES	4
+#define BITS_PER_STEP_RS	18
+#define BITS_PER_STEP_BCH	13
+
+#define INT_MASK		(IER_UND | IER_OVR | IER_CMD_DONE | IER_GIE)
+#define HWSTATUS_CMD_DEFAULT	NAND_STATUS_READY
+#define HWSTATUS_MASK_DEFAULT	(HWSTATUS_RDSTATUS_MASK(1) | \
+				HWSTATUS_RDSTATUS_VALUE(0) | \
+				HWSTATUS_RBSY_MASK(NAND_STATUS_READY) | \
+				HWSTATUS_RBSY_VALUE(NAND_STATUS_READY))
+
+struct tegra_nand_controller {
+	struct nand_hw_control controller;
+	struct device *dev;
+	void __iomem *regs;
+	int irq;
+	struct clk *clk;
+	struct completion command_complete;
+	struct completion dma_complete;
+	bool last_read_error;
+	int cur_cs;
+	struct nand_chip *chip;
+};
+
+struct tegra_nand_chip {
+	struct nand_chip chip;
+	struct gpio_desc *wp_gpio;
+	struct mtd_oob_region tag;
+	u32 config;
+	u32 config_ecc;
+	u32 bch_config;
+	int cs[1];
+};
+
+static inline struct tegra_nand_controller *to_tegra_ctrl(
+						struct nand_hw_control *hw_ctrl)
+{
+	return container_of(hw_ctrl, struct tegra_nand_controller, controller);
+}
+
+static inline struct tegra_nand_chip *to_tegra_chip(struct nand_chip *chip)
+{
+	return container_of(chip, struct tegra_nand_chip, chip);
+}
+
+static int tegra_nand_ooblayout_rs_ecc(struct mtd_info *mtd, int section,
+				       struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
+					  BITS_PER_BYTE);
+
+	if (section > 0)
+		return -ERANGE;
+
+	oobregion->offset = SKIP_SPARE_BYTES;
+	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
+
+	return 0;
+}
+
+static int tegra_nand_ooblayout_rs_free(struct mtd_info *mtd, int section,
+					struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
+					  BITS_PER_BYTE);
+
+	if (section > 0)
+		return -ERANGE;
+
+	oobregion->offset = SKIP_SPARE_BYTES +
+			    round_up(bytes_per_step * chip->ecc.steps, 4);
+	oobregion->length = mtd->oobsize - oobregion->offset;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops tegra_nand_oob_rs_ops = {
+	.ecc = tegra_nand_ooblayout_rs_ecc,
+	.free = tegra_nand_ooblayout_rs_free,
+};
+
+static int tegra_nand_ooblayout_bch_ecc(struct mtd_info *mtd, int section,
+				       struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
+					  BITS_PER_BYTE);
+
+	if (section > 0)
+		return -ERANGE;
+
+	oobregion->offset = SKIP_SPARE_BYTES;
+	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
+
+	return 0;
+}
+
+static int tegra_nand_ooblayout_bch_free(struct mtd_info *mtd, int section,
+					struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
+					  BITS_PER_BYTE);
+
+	if (section > 0)
+		return -ERANGE;
+
+	oobregion->offset = SKIP_SPARE_BYTES +
+			    round_up(bytes_per_step * chip->ecc.steps, 4);
+	oobregion->length = mtd->oobsize - oobregion->offset;
+
+	return 0;
+}
+
+/*
+ * Layout with tag bytes is
+ *
+ * --------------------------------------------------------------------------
+ * | main area                       | skip bytes | tag bytes | parity | .. |
+ * --------------------------------------------------------------------------
+ *
+ * If not tag bytes are written, parity moves right after skip bytes!
+ */
+static const struct mtd_ooblayout_ops tegra_nand_oob_bch_ops = {
+	.ecc = tegra_nand_ooblayout_bch_ecc,
+	.free = tegra_nand_ooblayout_bch_free,
+};
+
+static irqreturn_t tegra_nand_irq(int irq, void *data)
+{
+	struct tegra_nand_controller *ctrl = data;
+	u32 isr, dma;
+
+	isr = readl_relaxed(ctrl->regs + ISR);
+	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
+	dev_dbg(ctrl->dev, "isr %08x\n", isr);
+
+	if (!isr && !(dma & DMA_MST_CTRL_IS_DONE))
+		return IRQ_NONE;
+
+	/*
+	 * The bit name is somewhat missleading: This is also set when
+	 * HW ECC was successful. The data sheet states:
+	 * Correctable OR Un-correctable errors occurred in the DMA transfer...
+	 */
+	if (isr & ISR_CORRFAIL_ERR)
+		ctrl->last_read_error = true;
+
+	if (isr & ISR_CMD_DONE)
+		complete(&ctrl->command_complete);
+
+	if (isr & ISR_UND)
+		dev_err(ctrl->dev, "FIFO underrun\n");
+
+	if (isr & ISR_OVR)
+		dev_err(ctrl->dev, "FIFO overrun\n");
+
+	/* handle DMA interrupts */
+	if (dma & DMA_MST_CTRL_IS_DONE) {
+		writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
+		complete(&ctrl->dma_complete);
+	}
+
+	/* clear interrupts */
+	writel_relaxed(isr, ctrl->regs + ISR);
+
+	return IRQ_HANDLED;
+}
+
+static const char * const tegra_nand_reg_names[] = {
+	"COMMAND",
+	"STATUS",
+	"ISR",
+	"IER",
+	"CONFIG",
+	"TIMING",
+	NULL,
+	"TIMING2",
+	"CMD_REG1",
+	"CMD_REG2",
+	"ADDR_REG1",
+	"ADDR_REG2",
+	"DMA_MST_CTRL",
+	"DMA_CFG_A",
+	"DMA_CFG_B",
+	"FIFO_CTRL",
+};
+
+static void tegra_nand_dump_reg(struct tegra_nand_controller *ctrl)
+{
+	u32 reg;
+	int i;
+
+	dev_err(ctrl->dev, "Tegra NAND controller register dump\n");
+	for (i = 0; i < ARRAY_SIZE(tegra_nand_reg_names); i++) {
+		const char *reg_name = tegra_nand_reg_names[i];
+
+		if (!reg_name)
+			continue;
+
+		reg = readl_relaxed(ctrl->regs + (i * 4));
+		dev_err(ctrl->dev, "%s: 0x%08x\n", reg_name, reg);
+	}
+}
+
+static void tegra_nand_controller_abort(struct tegra_nand_controller *ctrl)
+{
+	u32 isr, dma;
+
+	disable_irq(ctrl->irq);
+
+	/* Abort current command/DMA operation */
+	writel_relaxed(0, ctrl->regs + DMA_MST_CTRL);
+	writel_relaxed(0, ctrl->regs + COMMAND);
+
+	/* clear interrupts */
+	isr = readl_relaxed(ctrl->regs + ISR);
+	writel_relaxed(isr, ctrl->regs + ISR);
+	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
+	writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
+
+	reinit_completion(&ctrl->command_complete);
+	reinit_completion(&ctrl->dma_complete);
+
+	enable_irq(ctrl->irq);
+}
+
+static int tegra_nand_cmd(struct nand_chip *chip,
+			 const struct nand_subop *subop)
+{
+	const struct nand_op_instr *instr;
+	const struct nand_op_instr *instr_data_in = NULL;
+	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
+	unsigned int op_id, size = 0, offset = 0;
+	bool first_cmd = true;
+	u32 reg, cmd = 0;
+	int ret;
+
+	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
+		unsigned int naddrs, i;
+		const u8 *addrs;
+		u32 addr1 = 0, addr2 = 0;
+
+		instr = &subop->instrs[op_id];
+
+		switch (instr->type) {
+		case NAND_OP_CMD_INSTR:
+			if (first_cmd) {
+				cmd |= COMMAND_CLE;
+				writel_relaxed(instr->ctx.cmd.opcode,
+					       ctrl->regs + CMD_REG1);
+			} else {
+				cmd |= COMMAND_SEC_CMD;
+				writel_relaxed(instr->ctx.cmd.opcode,
+					       ctrl->regs + CMD_REG2);
+			}
+			first_cmd = false;
+			break;
+		case NAND_OP_ADDR_INSTR:
+			offset = nand_subop_get_addr_start_off(subop, op_id);
+			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
+			addrs = &instr->ctx.addr.addrs[offset];
+
+			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
+			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
+				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
+			naddrs -= i;
+			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
+				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
+			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
+			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
+			break;
+
+		case NAND_OP_DATA_IN_INSTR:
+			size = nand_subop_get_data_len(subop, op_id);
+			offset = nand_subop_get_data_start_off(subop, op_id);
+
+			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
+				COMMAND_RX | COMMAND_A_VALID;
+
+			instr_data_in = instr;
+			break;
+
+		case NAND_OP_DATA_OUT_INSTR:
+			size = nand_subop_get_data_len(subop, op_id);
+			offset = nand_subop_get_data_start_off(subop, op_id);
+
+			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
+				COMMAND_TX | COMMAND_A_VALID;
+
+			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
+			writel_relaxed(reg, ctrl->regs + RESP);
+
+			break;
+		case NAND_OP_WAITRDY_INSTR:
+			cmd |= COMMAND_RBSY_CHK;
+			break;
+
+		}
+	}
+
+	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
+	writel_relaxed(cmd, ctrl->regs + COMMAND);
+	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
+					     msecs_to_jiffies(500));
+	if (!ret) {
+		dev_err(ctrl->dev, "COMMAND timeout\n");
+		tegra_nand_dump_reg(ctrl);
+		tegra_nand_controller_abort(ctrl);
+		return -ETIMEDOUT;
+	}
+
+	if (instr_data_in) {
+		reg = readl_relaxed(ctrl->regs + RESP);
+		memcpy(instr_data_in->ctx.data.buf.in + offset, &reg, size);
+	}
+
+	return 0;
+}
+
+static const struct nand_op_parser tegra_nand_op_parser = NAND_OP_PARSER(
+	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8),
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
+	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
+		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, 4)),
+	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8),
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, 4)),
+	);
+
+static int tegra_nand_exec_op(struct nand_chip *chip,
+			     const struct nand_operation *op,
+			     bool check_only)
+{
+	return nand_op_parser_exec_op(chip, &tegra_nand_op_parser, op,
+				      check_only);
+}
+static void tegra_nand_select_chip(struct mtd_info *mtd, int die_nr)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct tegra_nand_chip *nand = to_tegra_chip(chip);
+	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
+
+	if (die_nr < 0 || die_nr > 1) {
+		ctrl->cur_cs = -1;
+		return;
+	}
+
+	ctrl->cur_cs = nand->cs[die_nr];
+}
+
+static void tegra_nand_hw_ecc(struct tegra_nand_controller *ctrl,
+			      struct nand_chip *chip, bool enable)
+{
+	struct tegra_nand_chip *nand = to_tegra_chip(chip);
+
+	if (chip->ecc.algo == NAND_ECC_BCH && enable)
+		writel_relaxed(nand->bch_config, ctrl->regs + BCH_CONFIG);
+	else
+		writel_relaxed(0, ctrl->regs + BCH_CONFIG);
+
+	if (enable)
+		writel_relaxed(nand->config_ecc, ctrl->regs + CONFIG);
+	else
+		writel_relaxed(nand->config, ctrl->regs + CONFIG);
+}
+
+static int tegra_nand_page_xfer(struct mtd_info *mtd, struct nand_chip *chip,
+				void *buf, void *oob_buf, int oob_len, int page,
+				bool read)
+{
+	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
+	enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
+	dma_addr_t dma_addr = 0, dma_addr_oob = 0;
+	u32 addr1, cmd, dma_ctrl;
+	int ret;
+
+	if (read) {
+		writel_relaxed(NAND_CMD_READ0, ctrl->regs + CMD_REG1);
+		writel_relaxed(NAND_CMD_READSTART, ctrl->regs + CMD_REG2);
+	} else {
+		writel_relaxed(NAND_CMD_SEQIN, ctrl->regs + CMD_REG1);
+		writel_relaxed(NAND_CMD_PAGEPROG, ctrl->regs + CMD_REG2);
+	}
+	cmd = COMMAND_CLE | COMMAND_SEC_CMD;
+
+	/* Lower 16-bits are column, by default 0 */
+	addr1 = page << 16;
+
+	if (!buf)
+		addr1 |= mtd->writesize;
+	writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
+
+	if (chip->options & NAND_ROW_ADDR_3) {
+		writel_relaxed(page >> 16, ctrl->regs + ADDR_REG2);
+		cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(5);
+	} else {
+		cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(4);
+	}
+
+	if (buf) {
+		dma_addr = dma_map_single(ctrl->dev, buf, mtd->writesize, dir);
+		ret = dma_mapping_error(ctrl->dev, dma_addr);
+		if (ret) {
+			dev_err(ctrl->dev, "dma mapping error\n");
+			return -EINVAL;
+		}
+
+		writel_relaxed(mtd->writesize - 1, ctrl->regs + DMA_CFG_A);
+		writel_relaxed(dma_addr, ctrl->regs + DATA_PTR);
+	}
+
+	if (oob_buf) {
+		dma_addr_oob = dma_map_single(ctrl->dev, oob_buf, mtd->oobsize,
+					      dir);
+		ret = dma_mapping_error(ctrl->dev, dma_addr_oob);
+		if (ret) {
+			dev_err(ctrl->dev, "dma mapping error\n");
+			ret = -EINVAL;
+			goto err_unmap_dma_page;
+		}
+
+		writel_relaxed(oob_len - 1, ctrl->regs + DMA_CFG_B);
+		writel_relaxed(dma_addr_oob, ctrl->regs + TAG_PTR);
+	}
+
+	dma_ctrl = DMA_MST_CTRL_GO | DMA_MST_CTRL_PERF_EN |
+		   DMA_MST_CTRL_IE_DONE | DMA_MST_CTRL_IS_DONE |
+		   DMA_MST_CTRL_BURST_16;
+
+	if (buf)
+		dma_ctrl |= DMA_MST_CTRL_EN_A;
+	if (oob_buf)
+		dma_ctrl |= DMA_MST_CTRL_EN_B;
+
+	if (read)
+		dma_ctrl |= DMA_MST_CTRL_IN | DMA_MST_CTRL_REUSE;
+	else
+		dma_ctrl |= DMA_MST_CTRL_OUT;
+
+	writel_relaxed(dma_ctrl, ctrl->regs + DMA_MST_CTRL);
+
+	cmd |= COMMAND_GO | COMMAND_RBSY_CHK | COMMAND_TRANS_SIZE(9) |
+	       COMMAND_CE(ctrl->cur_cs);
+
+	if (buf)
+		cmd |= COMMAND_A_VALID;
+	if (oob_buf)
+		cmd |= COMMAND_B_VALID;
+
+	if (read)
+		cmd |= COMMAND_RX;
+	else
+		cmd |= COMMAND_TX | COMMAND_AFT_DAT;
+
+	writel_relaxed(cmd, ctrl->regs + COMMAND);
+
+	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
+					     msecs_to_jiffies(500));
+	if (!ret) {
+		dev_err(ctrl->dev, "COMMAND timeout\n");
+		tegra_nand_dump_reg(ctrl);
+		tegra_nand_controller_abort(ctrl);
+		ret = -ETIMEDOUT;
+		goto err_unmap_dma;
+	}
+
+	ret = wait_for_completion_io_timeout(&ctrl->dma_complete,
+					     msecs_to_jiffies(500));
+	if (!ret) {
+		dev_err(ctrl->dev, "DMA timeout\n");
+		tegra_nand_dump_reg(ctrl);
+		tegra_nand_controller_abort(ctrl);
+		ret = -ETIMEDOUT;
+		goto err_unmap_dma;
+	}
+	ret = 0;
+
+err_unmap_dma:
+	if (oob_buf)
+		dma_unmap_single(ctrl->dev, dma_addr_oob, mtd->oobsize, dir);
+err_unmap_dma_page:
+	if (buf)
+		dma_unmap_single(ctrl->dev, dma_addr, mtd->writesize, dir);
+
+	return ret;
+}
+
+static int tegra_nand_read_page_raw(struct mtd_info *mtd,
+				    struct nand_chip *chip,
+				    uint8_t *buf, int oob_required, int page)
+{
+	void *oob_buf = oob_required ? chip->oob_poi : 0;
+
+	return tegra_nand_page_xfer(mtd, chip, buf, oob_buf,
+				    mtd->oobsize, page, true);
+}
+
+static int tegra_nand_write_page_raw(struct mtd_info *mtd,
+				     struct nand_chip *chip,
+				     const uint8_t *buf, int oob_required,
+				     int page)
+{
+	void *oob_buf = oob_required ? chip->oob_poi : 0;
+
+	return tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf,
+				     mtd->oobsize, page, false);
+}
+
+static int tegra_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			       int page)
+{
+	return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi,
+				    mtd->oobsize, page, true);
+}
+
+static int tegra_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+				int page)
+{
+	return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi,
+				    mtd->oobsize, page, false);
+}
+
+static int tegra_nand_read_page_hwecc(struct mtd_info *mtd,
+				      struct nand_chip *chip,
+				      uint8_t *buf, int oob_required, int page)
+{
+	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
+	struct tegra_nand_chip *nand = to_tegra_chip(chip);
+	void *oob_buf = oob_required ? chip->oob_poi : 0;
+	u32 dec_stat, max_corr_cnt;
+	unsigned long fail_sec_flag;
+	int ret;
+
+	tegra_nand_hw_ecc(ctrl, chip, true);
+	ret = tegra_nand_page_xfer(mtd, chip, buf, oob_buf, nand->tag.length,
+				   page, true);
+	tegra_nand_hw_ecc(ctrl, chip, false);
+	if (ret)
+		return ret;
+
+	/* No correctable or un-correctable errors, page must have 0 bitflips */
+	if (!ctrl->last_read_error)
+		return 0;
+
+	/*
+	 * Correctable or un-correctable errors occurred. Use DEC_STAT_BUF
+	 * which contains information for all ECC selections.
+	 *
+	 * Note that since we do not use Command Queues DEC_RESULT does not
+	 * state the number of pages we can read from the DEC_STAT_BUF. But
+	 * since CORRFAIL_ERR did occur during page read we do have a valid
+	 * result in DEC_STAT_BUF.
+	 */
+	ctrl->last_read_error = false;
+	dec_stat = readl_relaxed(ctrl->regs + DEC_STAT_BUF);
+
+	fail_sec_flag = (dec_stat & DEC_STAT_BUF_FAIL_SEC_FLAG_MASK) >>
+			DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT;
+
+	max_corr_cnt = (dec_stat & DEC_STAT_BUF_MAX_CORR_CNT_MASK) >>
+		       DEC_STAT_BUF_MAX_CORR_CNT_SHIFT;
+
+	if (fail_sec_flag) {
+		int bit, max_bitflips = 0;
+
+		/*
+		 * Check if all sectors in a page failed. If only some failed
+		 * its definitly not an erased page and we can return error
+		 * stats right away.
+		 *
+		 * E.g. controller might return fail_sec_flag with 0x4, which
+		 * would mean only the third sector failed to correct.
+		 */
+		if (fail_sec_flag ^ GENMASK(chip->ecc.steps - 1, 0)) {
+			mtd->ecc_stats.failed += hweight8(fail_sec_flag);
+			return max_corr_cnt;
+		}
+
+		/*
+		 * All sectors failed to correct, but the ECC isn't smart
+		 * enough to figure out if a page is really completely erased.
+		 * We check the read data here to figure out if it's a
+		 * legitimate ECC error or only an erased page.
+		 */
+		for_each_set_bit(bit, &fail_sec_flag, chip->ecc.steps) {
+			u8 *data = buf + (chip->ecc.size * bit);
+
+			ret = nand_check_erased_ecc_chunk(data, chip->ecc.size,
+							  NULL, 0,
+							  NULL, 0,
+							  chip->ecc.strength);
+			if (ret < 0)
+				mtd->ecc_stats.failed++;
+			else
+				max_bitflips = max(ret, max_bitflips);
+		}
+
+		return max_t(unsigned int, max_corr_cnt, max_bitflips);
+	} else {
+		int corr_sec_flag;
+
+		corr_sec_flag = (dec_stat & DEC_STAT_BUF_CORR_SEC_FLAG_MASK) >>
+				DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT;
+
+		/*
+		 * The value returned in the register is the maximum of
+		 * bitflips encountered in any of the ECC regions. As there is
+		 * no way to get the number of bitflips in a specific regions
+		 * we are not able to deliver correct stats but instead
+		 * overestimate the number of corrected bitflips by assuming
+		 * that all regions where errors have been corrected
+		 * encountered the maximum number of bitflips.
+		 */
+		mtd->ecc_stats.corrected += max_corr_cnt * hweight8(corr_sec_flag);
+
+		return max_corr_cnt;
+	}
+
+}
+
+static int tegra_nand_write_page_hwecc(struct mtd_info *mtd,
+				       struct nand_chip *chip,
+				       const uint8_t *buf, int oob_required,
+				       int page)
+{
+	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
+	struct tegra_nand_chip *nand = to_tegra_chip(chip);
+	void *oob_buf = oob_required ? chip->oob_poi : 0;
+	int ret;
+
+	tegra_nand_hw_ecc(ctrl, chip, true);
+	ret = tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf,
+				   nand->tag.length, page, false);
+	tegra_nand_hw_ecc(ctrl, chip, false);
+
+	return ret;
+}
+
+static void tegra_nand_setup_timing(struct tegra_nand_controller *ctrl,
+				    const struct nand_sdr_timings *timings)
+{
+	/*
+	 * The period (and all other timings in this function) is in ps,
+	 * so need to take care here to avoid integer overflows.
+	 */
+	unsigned int rate = clk_get_rate(ctrl->clk) / 1000000;
+	unsigned int period = DIV_ROUND_UP(1000000, rate);
+	u32 val, reg = 0;
+
+	val = DIV_ROUND_UP(max3(timings->tAR_min, timings->tRR_min,
+				timings->tRC_min), period);
+	reg |= TIMING_TCR_TAR_TRR(OFFSET(val, 3));
+
+	val = DIV_ROUND_UP(max(max(timings->tCS_min, timings->tCH_min),
+			       max(timings->tALS_min, timings->tALH_min)),
+			   period);
+	reg |= TIMING_TCS(OFFSET(val, 2));
+
+	val = DIV_ROUND_UP(max(timings->tRP_min, timings->tREA_max) + 6000,
+			   period);
+	reg |= TIMING_TRP(OFFSET(val, 1)) | TIMING_TRP_RESP(OFFSET(val, 1));
+
+	reg |= TIMING_TWB(OFFSET(DIV_ROUND_UP(timings->tWB_max, period), 1));
+	reg |= TIMING_TWHR(OFFSET(DIV_ROUND_UP(timings->tWHR_min, period), 1));
+	reg |= TIMING_TWH(OFFSET(DIV_ROUND_UP(timings->tWH_min, period), 1));
+	reg |= TIMING_TWP(OFFSET(DIV_ROUND_UP(timings->tWP_min, period), 1));
+	reg |= TIMING_TRH(OFFSET(DIV_ROUND_UP(timings->tREH_min, period), 1));
+
+	writel_relaxed(reg, ctrl->regs + TIMING_1);
+
+	val = DIV_ROUND_UP(timings->tADL_min, period);
+	reg = TIMING_TADL(OFFSET(val, 3));
+
+	writel_relaxed(reg, ctrl->regs + TIMING_2);
+}
+
+static int tegra_nand_setup_data_interface(struct mtd_info *mtd, int csline,
+					const struct nand_data_interface *conf)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
+	const struct nand_sdr_timings *timings;
+
+	timings = nand_get_sdr_timings(conf);
+	if (IS_ERR(timings))
+		return PTR_ERR(timings);
+
+	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+		return 0;
+
+	tegra_nand_setup_timing(ctrl, timings);
+
+	return 0;
+}
+
+static const int rs_strength_bootable[] = { 4 };
+static const int rs_strength[] = { 4, 6, 8 };
+static const int bch_strength_bootable[] = { 8, 16 };
+static const int bch_strength[] = { 4, 8, 14, 16 };
+
+static int tegra_nand_get_strength(struct nand_chip *chip, const int *strength,
+				   int strength_len, int oobsize)
+{
+	bool maximize = chip->ecc.options & NAND_ECC_MAXIMIZE;
+	int i;
+
+	/*
+	 * Loop through available strengths. Backwards in case we try to
+	 * maximize the BCH strength.
+	 */
+	for (i = 0; i < strength_len; i++) {
+		int strength_sel, bytes_per_step, bytes_per_page;
+
+		if (maximize) {
+			strength_sel = strength[strength_len - i - 1];
+		} else {
+			strength_sel = strength[i];
+
+			if (strength_sel < chip->ecc_strength_ds)
+				continue;
+		}
+
+		bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * strength_sel,
+					      BITS_PER_BYTE);
+		bytes_per_page = round_up(bytes_per_step * chip->ecc.steps, 4);
+
+		/* Check whether strength fits OOB */
+		if (bytes_per_page < (oobsize - SKIP_SPARE_BYTES))
+			return strength_sel;
+	}
+
+	return -EINVAL;
+}
+
+static int tegra_nand_select_strength(struct nand_chip *chip, int oobsize)
+{
+	const int *strength;
+	int strength_len;
+
+	switch (chip->ecc.algo) {
+	case NAND_ECC_RS:
+		if (chip->options & NAND_IS_BOOT_MEDIUM) {
+			strength = rs_strength_bootable;
+			strength_len = ARRAY_SIZE(rs_strength_bootable);
+		} else {
+			strength = rs_strength;
+			strength_len = ARRAY_SIZE(rs_strength);
+		}
+		break;
+	case NAND_ECC_BCH:
+		if (chip->options & NAND_IS_BOOT_MEDIUM) {
+			strength = bch_strength_bootable;
+			strength_len = ARRAY_SIZE(bch_strength_bootable);
+		} else {
+			strength = bch_strength;
+			strength_len = ARRAY_SIZE(bch_strength);
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return tegra_nand_get_strength(chip, strength, strength_len, oobsize);
+}
+
+static int tegra_nand_chips_init(struct device *dev,
+				 struct tegra_nand_controller *ctrl)
+{
+	struct device_node *np = dev->of_node;
+	struct device_node *np_nand;
+	int nsels, nchips = of_get_child_count(np);
+	struct tegra_nand_chip *nand;
+	struct mtd_info *mtd;
+	struct nand_chip *chip;
+	int bits_per_step;
+	int ret;
+	u32 cs;
+
+	if (nchips != 1) {
+		dev_err(dev, "Currently only one NAND chip supported\n");
+		return -EINVAL;
+	}
+
+	np_nand = of_get_next_child(np, NULL);
+
+	nsels = of_property_count_elems_of_size(np_nand, "reg", sizeof(u32));
+	if (nsels != 1) {
+		dev_err(dev, "Missing/invalid reg property\n");
+		return -EINVAL;
+	}
+
+	/* Retrieve CS id, currently only single die NAND supported */
+	ret = of_property_read_u32(np_nand, "reg", &cs);
+	if (ret) {
+		dev_err(dev, "could not retrieve reg property: %d\n", ret);
+		return ret;
+	}
+
+	nand = devm_kzalloc(dev, sizeof(*nand), GFP_KERNEL);
+	if (!nand)
+		return -ENOMEM;
+
+	nand->cs[0] = cs;
+
+	nand->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_LOW);
+
+	if (IS_ERR(nand->wp_gpio)) {
+		ret = PTR_ERR(nand->wp_gpio);
+		dev_err(dev, "Failed to request WP GPIO: %d\n", ret);
+		return ret;
+	}
+
+	chip = &nand->chip;
+	chip->controller = &ctrl->controller;
+
+	mtd = nand_to_mtd(chip);
+
+	mtd->dev.parent = dev;
+	mtd->owner = THIS_MODULE;
+
+	nand_set_flash_node(chip, np_nand);
+
+	if (!mtd->name)
+		mtd->name = "tegra_nand";
+
+	chip->options = NAND_NO_SUBPAGE_WRITE | NAND_USE_BOUNCE_BUFFER;
+	chip->exec_op = tegra_nand_exec_op;
+	chip->select_chip = tegra_nand_select_chip;
+	chip->setup_data_interface = tegra_nand_setup_data_interface;
+
+	ret = nand_scan_ident(mtd, 1, NULL);
+	if (ret)
+		return ret;
+
+	if (chip->bbt_options & NAND_BBT_USE_FLASH)
+		chip->bbt_options |= NAND_BBT_NO_OOB;
+
+	chip->ecc.mode = NAND_ECC_HW;
+	chip->ecc.size = 512;
+	chip->ecc.steps = mtd->writesize / chip->ecc.size;
+	if (chip->ecc_step_ds != 512) {
+		dev_err(dev, "Unsupported step size %d\n", chip->ecc_step_ds);
+		return -EINVAL;
+	}
+
+	chip->ecc.read_page = tegra_nand_read_page_hwecc;
+	chip->ecc.write_page = tegra_nand_write_page_hwecc;
+	chip->ecc.read_page_raw = tegra_nand_read_page_raw;
+	chip->ecc.write_page_raw = tegra_nand_write_page_raw;
+	chip->ecc.read_oob = tegra_nand_read_oob;
+	chip->ecc.write_oob = tegra_nand_write_oob;
+
+	if (chip->options & NAND_BUSWIDTH_16)
+		nand->config |= CONFIG_BUS_WIDTH_16;
+
+	if (chip->ecc.algo == NAND_ECC_UNKNOWN) {
+		if (mtd->writesize < 2048)
+			chip->ecc.algo = NAND_ECC_RS;
+		else
+			chip->ecc.algo = NAND_ECC_BCH;
+	}
+
+	if (chip->ecc.algo == NAND_ECC_BCH && mtd->writesize < 2048) {
+		dev_err(dev, "BCH supportes 2K or 4K page size only\n");
+		return -EINVAL;
+	}
+
+	if (!chip->ecc.strength) {
+		ret = tegra_nand_select_strength(chip, mtd->oobsize);
+		if (ret < 0) {
+			dev_err(dev, "No valid strenght found, minimum %d\n",
+				chip->ecc_strength_ds);
+			return ret;
+		}
+
+		chip->ecc.strength = ret;
+	}
+
+	nand->config_ecc = CONFIG_PIPE_EN | CONFIG_SKIP_SPARE |
+			   CONFIG_SKIP_SPARE_SIZE_4;
+
+	switch (chip->ecc.algo) {
+	case NAND_ECC_RS:
+		bits_per_step = BITS_PER_STEP_RS * chip->ecc.strength;
+		mtd_set_ooblayout(mtd, &tegra_nand_oob_rs_ops);
+		nand->config_ecc |= CONFIG_HW_ECC | CONFIG_ECC_SEL |
+				    CONFIG_ERR_COR;
+		switch (chip->ecc.strength) {
+		case 4:
+			nand->config_ecc |= CONFIG_TVAL_4;
+			break;
+		case 6:
+			nand->config_ecc |= CONFIG_TVAL_6;
+			break;
+		case 8:
+			nand->config_ecc |= CONFIG_TVAL_8;
+			break;
+		default:
+			dev_err(dev, "ECC strength %d not supported\n",
+				chip->ecc.strength);
+			return -EINVAL;
+		}
+		break;
+	case NAND_ECC_BCH:
+		bits_per_step = BITS_PER_STEP_BCH * chip->ecc.strength;
+		mtd_set_ooblayout(mtd, &tegra_nand_oob_bch_ops);
+		nand->bch_config = BCH_ENABLE;
+		switch (chip->ecc.strength) {
+		case 4:
+			nand->bch_config |= BCH_TVAL_4;
+			break;
+		case 8:
+			nand->bch_config |= BCH_TVAL_8;
+			break;
+		case 14:
+			nand->bch_config |= BCH_TVAL_14;
+			break;
+		case 16:
+			nand->bch_config |= BCH_TVAL_16;
+			break;
+		default:
+			dev_err(dev, "ECC strength %d not supported\n",
+				chip->ecc.strength);
+			return -EINVAL;
+		}
+		break;
+	default:
+		dev_err(dev, "ECC algorithm not supported\n");
+		return -EINVAL;
+	}
+
+	dev_info(dev, "Using %s with strength %d per 512 byte step\n",
+			chip->ecc.algo == NAND_ECC_BCH ? "BCH" : "RS",
+			chip->ecc.strength);
+
+	chip->ecc.bytes = DIV_ROUND_UP(bits_per_step, BITS_PER_BYTE);
+
+	switch (mtd->writesize) {
+	case 256:
+		nand->config |= CONFIG_PS_256;
+		break;
+	case 512:
+		nand->config |= CONFIG_PS_512;
+		break;
+	case 1024:
+		nand->config |= CONFIG_PS_1024;
+		break;
+	case 2048:
+		nand->config |= CONFIG_PS_2048;
+		break;
+	case 4096:
+		nand->config |= CONFIG_PS_4096;
+		break;
+	default:
+		dev_err(dev, "Unsupported writesize %d\n", mtd->writesize);
+		return -ENODEV;
+	}
+
+	/* Store complete configuration in config_ecc */
+	nand->config_ecc |= nand->config;
+
+	/* Non-HW ECC read/writes complete OOB */
+	nand->config |= CONFIG_TAG_BYTE_SIZE(mtd->oobsize - 1);
+	writel_relaxed(nand->config, ctrl->regs + CONFIG);
+
+	ret = nand_scan_tail(mtd);
+	if (ret)
+		return ret;
+
+	/* Store tag layout when using HW ECC */
+	mtd_ooblayout_free(mtd, 0, &nand->tag);
+	nand->config_ecc |= CONFIG_TAG_BYTE_SIZE(nand->tag.length - 1);
+
+	ret = mtd_device_register(mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "Failed to register mtd device: %d\n", ret);
+		nand_cleanup(chip);
+		return ret;
+	}
+
+	ctrl->chip = chip;
+
+	return 0;
+}
+
+static int tegra_nand_probe(struct platform_device *pdev)
+{
+	struct reset_control *rst;
+	struct tegra_nand_controller *ctrl;
+	struct resource *res;
+	int err = 0;
+
+	ctrl = devm_kzalloc(&pdev->dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return -ENOMEM;
+
+	ctrl->dev = &pdev->dev;
+	nand_hw_control_init(&ctrl->controller);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ctrl->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ctrl->regs))
+		return PTR_ERR(ctrl->regs);
+
+	rst = devm_reset_control_get(&pdev->dev, "nand");
+	if (IS_ERR(rst))
+		return PTR_ERR(rst);
+
+	ctrl->clk = devm_clk_get(&pdev->dev, "nand");
+	if (IS_ERR(ctrl->clk))
+		return PTR_ERR(ctrl->clk);
+
+	err = clk_prepare_enable(ctrl->clk);
+	if (err)
+		return err;
+
+	err = reset_control_reset(rst);
+	if (err) {
+		dev_err(ctrl->dev, "Failed to reset HW: %d\n", err);
+		goto err_disable_clk;
+	}
+
+	writel_relaxed(HWSTATUS_CMD_DEFAULT, ctrl->regs + HWSTATUS_CMD);
+	writel_relaxed(HWSTATUS_MASK_DEFAULT, ctrl->regs + HWSTATUS_MASK);
+	writel_relaxed(INT_MASK, ctrl->regs + IER);
+
+	init_completion(&ctrl->command_complete);
+	init_completion(&ctrl->dma_complete);
+
+	ctrl->irq = platform_get_irq(pdev, 0);
+	err = devm_request_irq(&pdev->dev, ctrl->irq, tegra_nand_irq, 0,
+			       dev_name(&pdev->dev), ctrl);
+	if (err) {
+		dev_err(ctrl->dev, "Failed to get IRQ: %d\n", err);
+		goto err_disable_clk;
+	}
+
+	writel_relaxed(DMA_MST_CTRL_IS_DONE, ctrl->regs + DMA_MST_CTRL);
+
+	err = tegra_nand_chips_init(ctrl->dev, ctrl);
+	if (err)
+		goto err_disable_clk;
+
+	platform_set_drvdata(pdev, ctrl);
+
+	return 0;
+
+err_disable_clk:
+	clk_disable_unprepare(ctrl->clk);
+	return err;
+}
+
+static int tegra_nand_remove(struct platform_device *pdev)
+{
+	struct tegra_nand_controller *ctrl = platform_get_drvdata(pdev);
+
+	nand_release(nand_to_mtd(ctrl->chip));
+
+	clk_disable_unprepare(ctrl->clk);
+
+	return 0;
+}
+
+static const struct of_device_id tegra_nand_of_match[] = {
+	{ .compatible = "nvidia,tegra20-nand" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tegra_nand_of_match);
+
+static struct platform_driver tegra_nand_driver = {
+	.driver = {
+		.name = "tegra-nand",
+		.of_match_table = tegra_nand_of_match,
+	},
+	.probe = tegra_nand_probe,
+	.remove = tegra_nand_remove,
+};
+module_platform_driver(tegra_nand_driver);
+
+MODULE_DESCRIPTION("NVIDIA Tegra NAND driver");
+MODULE_AUTHOR("Thierry Reding <thierry.reding@nvidia.com>");
+MODULE_AUTHOR("Lucas Stach <dev@lynxeye.de>");
+MODULE_AUTHOR("Stefan Agner <stefan@agner.ch>");
+MODULE_LICENSE("GPL v2");
-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 5/6] ARM: dts: tegra: add Tegra20 NAND flash controller node
  2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
                   ` (3 preceding siblings ...)
  2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
@ 2018-06-11 20:52 ` Stefan Agner
  2018-06-11 20:52 ` [PATCH v4 6/6] ARM: dts: tegra: enable NAND flash on Colibri T20 Stefan Agner
  5 siblings, 0 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

From: Lucas Stach <dev@lynxeye.de>

Add basic controller device tree node to be extended by
individual boards. Use the assigned-clocks mechanism to set
NDFLASH clock to a sensible default rate of 150MHz.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 arch/arm/boot/dts/tegra20.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index 0a7136462a1a..530a009086d5 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -425,6 +425,21 @@
 		status = "disabled";
 	};
 
+	nand-controller@70008000 {
+		compatible = "nvidia,tegra20-nand";
+		reg = <0x70008000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
+		clock-names = "nand";
+		resets = <&tegra_car 13>;
+		reset-names = "nand";
+		assigned-clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
+		assigned-clock-rates = <150000000>;
+		status = "disabled";
+	};
+
 	pwm: pwm@7000a000 {
 		compatible = "nvidia,tegra20-pwm";
 		reg = <0x7000a000 0x100>;
-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 6/6] ARM: dts: tegra: enable NAND flash on Colibri T20
  2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
                   ` (4 preceding siblings ...)
  2018-06-11 20:52 ` [PATCH v4 5/6] ARM: dts: tegra: add Tegra20 NAND flash controller node Stefan Agner
@ 2018-06-11 20:52 ` Stefan Agner
  5 siblings, 0 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-11 20:52 UTC (permalink / raw)
  To: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding
  Cc: dev, miquel.raynal, richard, marcel, krzk, digetx,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel, Stefan Agner

This enables the on-module ONFI conformant NAND flash.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 arch/arm/boot/dts/tegra20-colibri-512.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm/boot/dts/tegra20-colibri-512.dtsi b/arch/arm/boot/dts/tegra20-colibri-512.dtsi
index 5c202b3e3bb1..0c283fb77214 100644
--- a/arch/arm/boot/dts/tegra20-colibri-512.dtsi
+++ b/arch/arm/boot/dts/tegra20-colibri-512.dtsi
@@ -462,6 +462,22 @@
 		};
 	};
 
+	nand-controller@70008000 {
+		status = "okay";
+
+		nand@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			nand-bus-width = <8>;
+			nand-on-flash-bbt;
+			nand-ecc-algo = "bch";
+			nand-is-boot-medium;
+			nand-ecc-maximize;
+			wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>;
+		};
+	};
+
 	usb@c5004000 {
 		status = "okay";
 		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-- 
2.17.1


^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
@ 2018-06-11 23:08   ` kbuild test robot
  2018-06-11 23:32   ` Dmitry Osipenko
                     ` (2 subsequent siblings)
  3 siblings, 0 replies; 24+ messages in thread
From: kbuild test robot @ 2018-06-11 23:08 UTC (permalink / raw)
  To: Stefan Agner
  Cc: kbuild-all, boris.brezillon, dwmw2, computersforpeace,
	marek.vasut, robh+dt, mark.rutland, thierry.reding, dev,
	miquel.raynal, richard, marcel, krzk, digetx, benjamin.lindqvist,
	jonathanh, pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel, Stefan Agner

Hi Stefan,

I love your patch! Perhaps something to improve:

[auto build test WARNING on mtd/nand/next]
[also build test WARNING on v4.17 next-20180608]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/Stefan-Agner/mtd-rawnand-add-NVIDIA-Tegra-NAND-flash-support/20180612-045611
base:   git://git.infradead.org/linux-mtd.git nand/next
reproduce:
        # apt-get install sparse
        make ARCH=x86_64 allmodconfig
        make C=1 CF=-D__CHECK_ENDIAN__


sparse warnings: (new ones prefixed by >>)

   drivers/mtd/nand/raw/tegra_nand.c:422:41: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:425:41: sparse: expression using sizeof(void)
>> drivers/mtd/nand/raw/tegra_nand.c:656:56: sparse: Using plain integer as NULL pointer
   drivers/mtd/nand/raw/tegra_nand.c:667:56: sparse: Using plain integer as NULL pointer
   drivers/mtd/nand/raw/tegra_nand.c:693:56: sparse: Using plain integer as NULL pointer
   drivers/mtd/nand/raw/tegra_nand.c:759:48: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:759:48: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:762:24: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:762:24: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:792:56: sparse: Using plain integer as NULL pointer
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:814:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:818:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:823:15: sparse: expression using sizeof(void)
   drivers/mtd/nand/raw/tegra_nand.c:823:15: sparse: expression using sizeof(void)

vim +656 drivers/mtd/nand/raw/tegra_nand.c

   651	
   652	static int tegra_nand_read_page_raw(struct mtd_info *mtd,
   653					    struct nand_chip *chip,
   654					    uint8_t *buf, int oob_required, int page)
   655	{
 > 656		void *oob_buf = oob_required ? chip->oob_poi : 0;
   657	
   658		return tegra_nand_page_xfer(mtd, chip, buf, oob_buf,
   659					    mtd->oobsize, page, true);
   660	}
   661	

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
  2018-06-11 23:08   ` kbuild test robot
@ 2018-06-11 23:32   ` Dmitry Osipenko
  2018-06-12  8:02     ` Stefan Agner
  2018-06-12  0:03   ` Dmitry Osipenko
  2018-06-12 12:17   ` Dmitry Osipenko
  3 siblings, 1 reply; 24+ messages in thread
From: Dmitry Osipenko @ 2018-06-11 23:32 UTC (permalink / raw)
  To: Stefan Agner
  Cc: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
> Add support for the NAND flash controller found on NVIDIA
> Tegra 2 SoCs. This implementation does not make use of the
> command queue feature. Regular operations/data transfers are
> done in PIO mode. Page read/writes with hardware ECC make
> use of the DMA for data transfer.

Are "regular operations/data transfers" == "raw read/writes"? Seems you've 
fixed DMA now and hence should adjust the commit message if that's the case.

> 
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---

Otherwise looks good to me:

Reviewed-by: Dmitry Osipenko <digetx@gmail.com>


There couple nit comments about newlines below, maybe you could clean up them 
if there will be another revision.

>  MAINTAINERS                       |    7 +
>  drivers/mtd/nand/raw/Kconfig      |    6 +
>  drivers/mtd/nand/raw/Makefile     |    1 +
>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>  4 files changed, 1262 insertions(+)
>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 58b9861ccf99..c2e5571c85d4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13844,6 +13844,13 @@ M:	Laxman Dewangan <ldewangan@nvidia.com>
>  S:	Supported
>  F:	drivers/input/keyboard/tegra-kbc.c
> 
> +TEGRA NAND DRIVER
> +M:	Stefan Agner <stefan@agner.ch>
> +M:	Lucas Stach <dev@lynxeye.de>
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
> +F:	drivers/mtd/nand/raw/tegra_nand.c
> +
>  TEGRA PWM DRIVER
>  M:	Thierry Reding <thierry.reding@gmail.com>
>  S:	Supported
> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
> index 19a2b283fbbe..e9093f52371e 100644
> --- a/drivers/mtd/nand/raw/Kconfig
> +++ b/drivers/mtd/nand/raw/Kconfig
> @@ -534,4 +534,10 @@ config MTD_NAND_MTK
>  	  Enables support for NAND controller on MTK SoCs.
>  	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
> 
> +config MTD_NAND_TEGRA
> +	tristate "Support for NAND controller on NVIDIA Tegra"
> +	depends on ARCH_TEGRA || COMPILE_TEST
> +	help
> +	  Enables support for NAND flash controller on NVIDIA Tegra SoC.
> +
>  endif # MTD_NAND
> diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
> index 165b7ef9e9a1..d5a5f9832b88 100644
> --- a/drivers/mtd/nand/raw/Makefile
> +++ b/drivers/mtd/nand/raw/Makefile
> @@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504)	        += 
hisi504_nand.o
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
>  obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
>  obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
> +obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
> 
>  nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
>  nand-objs += nand_amd.o
> diff --git a/drivers/mtd/nand/raw/tegra_nand.c
> b/drivers/mtd/nand/raw/tegra_nand.c new file mode 100644
> index 000000000000..dd23a5eb6af3
> --- /dev/null
> +++ b/drivers/mtd/nand/raw/tegra_nand.c
> @@ -0,0 +1,1248 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2018 Stefan Agner <stefan@agner.ch>
> + * Copyright (C) 2014-2015 Lucas Stach <dev@lynxeye.de>
> + * Copyright (C) 2012 Avionic Design GmbH
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/err.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/mtd/partitions.h>
> +#include <linux/mtd/rawnand.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +
> +#define COMMAND					0x00
> +#define   COMMAND_GO				BIT(31)
> +#define   COMMAND_CLE				BIT(30)
> +#define   COMMAND_ALE				BIT(29)
> +#define   COMMAND_PIO				BIT(28)
> +#define   COMMAND_TX				BIT(27)
> +#define   COMMAND_RX				BIT(26)
> +#define   COMMAND_SEC_CMD			BIT(25)
> +#define   COMMAND_AFT_DAT			BIT(24)
> +#define   COMMAND_TRANS_SIZE(x)			(((x - 1) & 0xf) << 20)
> +#define   COMMAND_A_VALID			BIT(19)
> +#define   COMMAND_B_VALID			BIT(18)
> +#define   COMMAND_RD_STATUS_CHK			BIT(17)
> +#define   COMMAND_RBSY_CHK			BIT(16)
> +#define   COMMAND_CE(x)				BIT(8 + ((x) & 0x7))
> +#define   COMMAND_CLE_SIZE(x)			(((x - 1) & 0x3) << 4)
> +#define   COMMAND_ALE_SIZE(x)			(((x - 1) & 0xf) << 0)
> +
> +#define STATUS					0x04
> +
> +#define ISR					0x08
> +#define   ISR_CORRFAIL_ERR			BIT(24)
> +#define   ISR_UND				BIT(7)
> +#define   ISR_OVR				BIT(6)
> +#define   ISR_CMD_DONE				BIT(5)
> +#define   ISR_ECC_ERR				BIT(4)
> +
> +#define IER					0x0c
> +#define   IER_ERR_TRIG_VAL(x)			(((x) & 0xf) << 16)
> +#define   IER_UND				BIT(7)
> +#define   IER_OVR				BIT(6)
> +#define   IER_CMD_DONE				BIT(5)
> +#define   IER_ECC_ERR				BIT(4)
> +#define   IER_GIE				BIT(0)
> +
> +#define CONFIG					0x10
> +#define   CONFIG_HW_ECC				BIT(31)
> +#define   CONFIG_ECC_SEL			BIT(30)
> +#define   CONFIG_ERR_COR			BIT(29)
> +#define   CONFIG_PIPE_EN			BIT(28)
> +#define   CONFIG_TVAL_4				(0 << 24)
> +#define   CONFIG_TVAL_6				(1 << 24)
> +#define   CONFIG_TVAL_8				(2 << 24)
> +#define   CONFIG_SKIP_SPARE			BIT(23)
> +#define   CONFIG_BUS_WIDTH_16			BIT(21)
> +#define   CONFIG_COM_BSY			BIT(20)
> +#define   CONFIG_PS_256				(0 << 16)
> +#define   CONFIG_PS_512				(1 << 16)
> +#define   CONFIG_PS_1024			(2 << 16)
> +#define   CONFIG_PS_2048			(3 << 16)
> +#define   CONFIG_PS_4096			(4 << 16)
> +#define   CONFIG_SKIP_SPARE_SIZE_4		(0 << 14)
> +#define   CONFIG_SKIP_SPARE_SIZE_8		(1 << 14)
> +#define   CONFIG_SKIP_SPARE_SIZE_12		(2 << 14)
> +#define   CONFIG_SKIP_SPARE_SIZE_16		(3 << 14)
> +#define   CONFIG_TAG_BYTE_SIZE(x)			((x) & 0xff)
> +
> +#define TIMING_1				0x14
> +#define   TIMING_TRP_RESP(x)			(((x) & 0xf) << 28)
> +#define   TIMING_TWB(x)				(((x) & 0xf) << 24)
> +#define   TIMING_TCR_TAR_TRR(x)			(((x) & 0xf) << 20)
> +#define   TIMING_TWHR(x)			(((x) & 0xf) << 16)
> +#define   TIMING_TCS(x)				(((x) & 0x3) << 14)
> +#define   TIMING_TWH(x)				(((x) & 0x3) << 12)
> +#define   TIMING_TWP(x)				(((x) & 0xf) <<  8)
> +#define   TIMING_TRH(x)				(((x) & 0x3) <<  4)
> +#define   TIMING_TRP(x)				(((x) & 0xf) <<  0)
> +
> +#define RESP					0x18
> +
> +#define TIMING_2				0x1c
> +#define   TIMING_TADL(x)			((x) & 0xf)
> +
> +#define CMD_REG1				0x20
> +#define CMD_REG2				0x24
> +#define ADDR_REG1				0x28
> +#define ADDR_REG2				0x2c
> +
> +#define DMA_MST_CTRL				0x30
> +#define   DMA_MST_CTRL_GO			BIT(31)
> +#define   DMA_MST_CTRL_IN			(0 << 30)
> +#define   DMA_MST_CTRL_OUT			BIT(30)
> +#define   DMA_MST_CTRL_PERF_EN			BIT(29)
> +#define   DMA_MST_CTRL_IE_DONE			BIT(28)
> +#define   DMA_MST_CTRL_REUSE			BIT(27)
> +#define   DMA_MST_CTRL_BURST_1			(2 << 24)
> +#define   DMA_MST_CTRL_BURST_4			(3 << 24)
> +#define   DMA_MST_CTRL_BURST_8			(4 << 24)
> +#define   DMA_MST_CTRL_BURST_16			(5 << 24)
> +#define   DMA_MST_CTRL_IS_DONE			BIT(20)
> +#define   DMA_MST_CTRL_EN_A			BIT(2)
> +#define   DMA_MST_CTRL_EN_B			BIT(1)
> +
> +#define DMA_CFG_A				0x34
> +#define DMA_CFG_B				0x38
> +
> +#define FIFO_CTRL				0x3c
> +#define   FIFO_CTRL_CLR_ALL			BIT(3)
> +
> +#define DATA_PTR				0x40
> +#define TAG_PTR					0x44
> +#define ECC_PTR					0x48
> +
> +#define DEC_STATUS				0x4c
> +#define   DEC_STATUS_A_ECC_FAIL			BIT(1)
> +#define   DEC_STATUS_ERR_COUNT_MASK		0x00ff0000
> +#define   DEC_STATUS_ERR_COUNT_SHIFT		16
> +
> +#define HWSTATUS_CMD				0x50
> +#define HWSTATUS_MASK				0x54
> +#define   HWSTATUS_RDSTATUS_MASK(x)		(((x) & 0xff) << 24)
> +#define   HWSTATUS_RDSTATUS_VALUE(x)		(((x) & 0xff) << 16)
> +#define   HWSTATUS_RBSY_MASK(x)			(((x) & 0xff) << 8)
> +#define   HWSTATUS_RBSY_VALUE(x)		(((x) & 0xff) << 0)
> +
> +#define BCH_CONFIG				0xcc
> +#define   BCH_ENABLE				BIT(0)
> +#define   BCH_TVAL_4				(0 << 4)
> +#define   BCH_TVAL_8				(1 << 4)
> +#define   BCH_TVAL_14				(2 << 4)
> +#define   BCH_TVAL_16				(3 << 4)
> +
> +#define DEC_STAT_RESULT				0xd0
> +#define DEC_STAT_BUF				0xd4
> +#define   DEC_STAT_BUF_FAIL_SEC_FLAG_MASK	0xff000000
> +#define   DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT	24
> +#define   DEC_STAT_BUF_CORR_SEC_FLAG_MASK	0x00ff0000
> +#define   DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT	16
> +#define   DEC_STAT_BUF_MAX_CORR_CNT_MASK	0x00001f00
> +#define   DEC_STAT_BUF_MAX_CORR_CNT_SHIFT	8
> +
> +#define OFFSET(val, off)	((val) < (off) ? 0 : (val) - (off))
> +
> +#define SKIP_SPARE_BYTES	4
> +#define BITS_PER_STEP_RS	18
> +#define BITS_PER_STEP_BCH	13
> +
> +#define INT_MASK		(IER_UND | IER_OVR | IER_CMD_DONE | IER_GIE)
> +#define HWSTATUS_CMD_DEFAULT	NAND_STATUS_READY
> +#define HWSTATUS_MASK_DEFAULT	(HWSTATUS_RDSTATUS_MASK(1) | \
> +				HWSTATUS_RDSTATUS_VALUE(0) | \
> +				HWSTATUS_RBSY_MASK(NAND_STATUS_READY) | \
> +				HWSTATUS_RBSY_VALUE(NAND_STATUS_READY))
> +
> +struct tegra_nand_controller {
> +	struct nand_hw_control controller;
> +	struct device *dev;
> +	void __iomem *regs;
> +	int irq;
> +	struct clk *clk;
> +	struct completion command_complete;
> +	struct completion dma_complete;
> +	bool last_read_error;
> +	int cur_cs;
> +	struct nand_chip *chip;
> +};
> +
> +struct tegra_nand_chip {
> +	struct nand_chip chip;
> +	struct gpio_desc *wp_gpio;
> +	struct mtd_oob_region tag;
> +	u32 config;
> +	u32 config_ecc;
> +	u32 bch_config;
> +	int cs[1];
> +};
> +
> +static inline struct tegra_nand_controller *to_tegra_ctrl(
> +						struct nand_hw_control *hw_ctrl)
> +{
> +	return container_of(hw_ctrl, struct tegra_nand_controller, controller);
> +}
> +
> +static inline struct tegra_nand_chip *to_tegra_chip(struct nand_chip *chip)
> +{
> +	return container_of(chip, struct tegra_nand_chip, chip);
> +}
> +
> +static int tegra_nand_ooblayout_rs_ecc(struct mtd_info *mtd, int section,
> +				       struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES;
> +	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
> +
> +	return 0;
> +}
> +
> +static int tegra_nand_ooblayout_rs_free(struct mtd_info *mtd, int section,
> +					struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES +
> +			    round_up(bytes_per_step * chip->ecc.steps, 4);
> +	oobregion->length = mtd->oobsize - oobregion->offset;
> +
> +	return 0;
> +}
> +
> +static const struct mtd_ooblayout_ops tegra_nand_oob_rs_ops = {
> +	.ecc = tegra_nand_ooblayout_rs_ecc,
> +	.free = tegra_nand_ooblayout_rs_free,
> +};
> +
> +static int tegra_nand_ooblayout_bch_ecc(struct mtd_info *mtd, int section,
> +				       struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES;
> +	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
> +
> +	return 0;
> +}
> +
> +static int tegra_nand_ooblayout_bch_free(struct mtd_info *mtd, int section,
> +					struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES +
> +			    round_up(bytes_per_step * chip->ecc.steps, 4);
> +	oobregion->length = mtd->oobsize - oobregion->offset;
> +
> +	return 0;
> +}
> +
> +/*
> + * Layout with tag bytes is
> + *
> + *
> --------------------------------------------------------------------------
> + * | main area                       | skip bytes | tag bytes | parity |
> .. | + *
> --------------------------------------------------------------------------
> + *
> + * If not tag bytes are written, parity moves right after skip bytes!
> + */
> +static const struct mtd_ooblayout_ops tegra_nand_oob_bch_ops = {
> +	.ecc = tegra_nand_ooblayout_bch_ecc,
> +	.free = tegra_nand_ooblayout_bch_free,
> +};
> +
> +static irqreturn_t tegra_nand_irq(int irq, void *data)
> +{
> +	struct tegra_nand_controller *ctrl = data;
> +	u32 isr, dma;
> +
> +	isr = readl_relaxed(ctrl->regs + ISR);
> +	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
> +	dev_dbg(ctrl->dev, "isr %08x\n", isr);
> +
> +	if (!isr && !(dma & DMA_MST_CTRL_IS_DONE))
> +		return IRQ_NONE;
> +
> +	/*
> +	 * The bit name is somewhat missleading: This is also set when
> +	 * HW ECC was successful. The data sheet states:
> +	 * Correctable OR Un-correctable errors occurred in the DMA transfer...
> +	 */
> +	if (isr & ISR_CORRFAIL_ERR)
> +		ctrl->last_read_error = true;
> +
> +	if (isr & ISR_CMD_DONE)
> +		complete(&ctrl->command_complete);
> +
> +	if (isr & ISR_UND)
> +		dev_err(ctrl->dev, "FIFO underrun\n");
> +
> +	if (isr & ISR_OVR)
> +		dev_err(ctrl->dev, "FIFO overrun\n");
> +
> +	/* handle DMA interrupts */
> +	if (dma & DMA_MST_CTRL_IS_DONE) {
> +		writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
> +		complete(&ctrl->dma_complete);
> +	}
> +
> +	/* clear interrupts */
> +	writel_relaxed(isr, ctrl->regs + ISR);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static const char * const tegra_nand_reg_names[] = {
> +	"COMMAND",
> +	"STATUS",
> +	"ISR",
> +	"IER",
> +	"CONFIG",
> +	"TIMING",
> +	NULL,
> +	"TIMING2",
> +	"CMD_REG1",
> +	"CMD_REG2",
> +	"ADDR_REG1",
> +	"ADDR_REG2",
> +	"DMA_MST_CTRL",
> +	"DMA_CFG_A",
> +	"DMA_CFG_B",
> +	"FIFO_CTRL",
> +};
> +
> +static void tegra_nand_dump_reg(struct tegra_nand_controller *ctrl)
> +{
> +	u32 reg;
> +	int i;
> +
> +	dev_err(ctrl->dev, "Tegra NAND controller register dump\n");
> +	for (i = 0; i < ARRAY_SIZE(tegra_nand_reg_names); i++) {
> +		const char *reg_name = tegra_nand_reg_names[i];
> +
> +		if (!reg_name)
> +			continue;
> +
> +		reg = readl_relaxed(ctrl->regs + (i * 4));
> +		dev_err(ctrl->dev, "%s: 0x%08x\n", reg_name, reg);
> +	}
> +}
> +
> +static void tegra_nand_controller_abort(struct tegra_nand_controller *ctrl)
> +{
> +	u32 isr, dma;
> +
> +	disable_irq(ctrl->irq);
> +
> +	/* Abort current command/DMA operation */
> +	writel_relaxed(0, ctrl->regs + DMA_MST_CTRL);
> +	writel_relaxed(0, ctrl->regs + COMMAND);
> +
> +	/* clear interrupts */
> +	isr = readl_relaxed(ctrl->regs + ISR);
> +	writel_relaxed(isr, ctrl->regs + ISR);
> +	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
> +	writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
> +
> +	reinit_completion(&ctrl->command_complete);
> +	reinit_completion(&ctrl->dma_complete);
> +
> +	enable_irq(ctrl->irq);
> +}
> +
> +static int tegra_nand_cmd(struct nand_chip *chip,
> +			 const struct nand_subop *subop)
> +{
> +	const struct nand_op_instr *instr;
> +	const struct nand_op_instr *instr_data_in = NULL;
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +	unsigned int op_id, size = 0, offset = 0;
> +	bool first_cmd = true;
> +	u32 reg, cmd = 0;
> +	int ret;
> +
> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
> +		unsigned int naddrs, i;
> +		const u8 *addrs;
> +		u32 addr1 = 0, addr2 = 0;
> +
> +		instr = &subop->instrs[op_id];
> +
> +		switch (instr->type) {
> +		case NAND_OP_CMD_INSTR:
> +			if (first_cmd) {
> +				cmd |= COMMAND_CLE;
> +				writel_relaxed(instr->ctx.cmd.opcode,
> +					       ctrl->regs + CMD_REG1);
> +			} else {
> +				cmd |= COMMAND_SEC_CMD;
> +				writel_relaxed(instr->ctx.cmd.opcode,
> +					       ctrl->regs + CMD_REG2);
> +			}
> +			first_cmd = false;
> +			break;

Newline here.

> +		case NAND_OP_ADDR_INSTR:
> +			offset = nand_subop_get_addr_start_off(subop, op_id);
> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
> +			addrs = &instr->ctx.addr.addrs[offset];
> +
> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
> +			naddrs -= i;
> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
> +			break;
> +
> +		case NAND_OP_DATA_IN_INSTR:
> +			size = nand_subop_get_data_len(subop, op_id);
> +			offset = nand_subop_get_data_start_off(subop, op_id);
> +
> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> +				COMMAND_RX | COMMAND_A_VALID;
> +
> +			instr_data_in = instr;
> +			break;
> +
> +		case NAND_OP_DATA_OUT_INSTR:
> +			size = nand_subop_get_data_len(subop, op_id);
> +			offset = nand_subop_get_data_start_off(subop, op_id);
> +
> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> +				COMMAND_TX | COMMAND_A_VALID;
> +
> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
> +			writel_relaxed(reg, ctrl->regs + RESP);
> +
> +			break;

Newline here.

> +		case NAND_OP_WAITRDY_INSTR:
> +			cmd |= COMMAND_RBSY_CHK;
> +			break;
> +

Blank line isn't needed here.

> +		}
> +	}
> +
> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> +					     msecs_to_jiffies(500));
> +	if (!ret) {
> +		dev_err(ctrl->dev, "COMMAND timeout\n");
> +		tegra_nand_dump_reg(ctrl);
> +		tegra_nand_controller_abort(ctrl);
> +		return -ETIMEDOUT;
> +	}
> +
> +	if (instr_data_in) {
> +		reg = readl_relaxed(ctrl->regs + RESP);
> +		memcpy(instr_data_in->ctx.data.buf.in + offset, &reg, size);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct nand_op_parser tegra_nand_op_parser = NAND_OP_PARSER(
> +	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
> +		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8),
> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
> +		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
> +	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
> +		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, 4)),
> +	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
> +		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8),
> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
> +		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
> +		NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, 4)),
> +	);
> +
> +static int tegra_nand_exec_op(struct nand_chip *chip,
> +			     const struct nand_operation *op,
> +			     bool check_only)
> +{
> +	return nand_op_parser_exec_op(chip, &tegra_nand_op_parser, op,
> +				      check_only);
> +}

Newline here.

> +static void tegra_nand_select_chip(struct mtd_info *mtd, int die_nr)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +
> +	if (die_nr < 0 || die_nr > 1) {
> +		ctrl->cur_cs = -1;
> +		return;
> +	}
> +
> +	ctrl->cur_cs = nand->cs[die_nr];
> +}
> +
> +static void tegra_nand_hw_ecc(struct tegra_nand_controller *ctrl,
> +			      struct nand_chip *chip, bool enable)
> +{
> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
> +
> +	if (chip->ecc.algo == NAND_ECC_BCH && enable)
> +		writel_relaxed(nand->bch_config, ctrl->regs + BCH_CONFIG);
> +	else
> +		writel_relaxed(0, ctrl->regs + BCH_CONFIG);
> +
> +	if (enable)
> +		writel_relaxed(nand->config_ecc, ctrl->regs + CONFIG);
> +	else
> +		writel_relaxed(nand->config, ctrl->regs + CONFIG);
> +}
> +
> +static int tegra_nand_page_xfer(struct mtd_info *mtd, struct nand_chip
> *chip, +				void *buf, void *oob_buf, int oob_len, int page,
> +				bool read)
> +{
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +	enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
> +	dma_addr_t dma_addr = 0, dma_addr_oob = 0;
> +	u32 addr1, cmd, dma_ctrl;
> +	int ret;
> +
> +	if (read) {
> +		writel_relaxed(NAND_CMD_READ0, ctrl->regs + CMD_REG1);
> +		writel_relaxed(NAND_CMD_READSTART, ctrl->regs + CMD_REG2);
> +	} else {
> +		writel_relaxed(NAND_CMD_SEQIN, ctrl->regs + CMD_REG1);
> +		writel_relaxed(NAND_CMD_PAGEPROG, ctrl->regs + CMD_REG2);
> +	}
> +	cmd = COMMAND_CLE | COMMAND_SEC_CMD;
> +
> +	/* Lower 16-bits are column, by default 0 */
> +	addr1 = page << 16;
> +
> +	if (!buf)
> +		addr1 |= mtd->writesize;
> +	writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> +
> +	if (chip->options & NAND_ROW_ADDR_3) {
> +		writel_relaxed(page >> 16, ctrl->regs + ADDR_REG2);
> +		cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(5);
> +	} else {
> +		cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(4);
> +	}
> +
> +	if (buf) {
> +		dma_addr = dma_map_single(ctrl->dev, buf, mtd->writesize, dir);
> +		ret = dma_mapping_error(ctrl->dev, dma_addr);
> +		if (ret) {
> +			dev_err(ctrl->dev, "dma mapping error\n");
> +			return -EINVAL;
> +		}
> +
> +		writel_relaxed(mtd->writesize - 1, ctrl->regs + DMA_CFG_A);
> +		writel_relaxed(dma_addr, ctrl->regs + DATA_PTR);
> +	}
> +
> +	if (oob_buf) {
> +		dma_addr_oob = dma_map_single(ctrl->dev, oob_buf, mtd->oobsize,
> +					      dir);
> +		ret = dma_mapping_error(ctrl->dev, dma_addr_oob);
> +		if (ret) {
> +			dev_err(ctrl->dev, "dma mapping error\n");
> +			ret = -EINVAL;
> +			goto err_unmap_dma_page;
> +		}
> +
> +		writel_relaxed(oob_len - 1, ctrl->regs + DMA_CFG_B);
> +		writel_relaxed(dma_addr_oob, ctrl->regs + TAG_PTR);
> +	}
> +
> +	dma_ctrl = DMA_MST_CTRL_GO | DMA_MST_CTRL_PERF_EN |
> +		   DMA_MST_CTRL_IE_DONE | DMA_MST_CTRL_IS_DONE |
> +		   DMA_MST_CTRL_BURST_16;
> +
> +	if (buf)
> +		dma_ctrl |= DMA_MST_CTRL_EN_A;
> +	if (oob_buf)
> +		dma_ctrl |= DMA_MST_CTRL_EN_B;
> +
> +	if (read)
> +		dma_ctrl |= DMA_MST_CTRL_IN | DMA_MST_CTRL_REUSE;
> +	else
> +		dma_ctrl |= DMA_MST_CTRL_OUT;
> +
> +	writel_relaxed(dma_ctrl, ctrl->regs + DMA_MST_CTRL);
> +
> +	cmd |= COMMAND_GO | COMMAND_RBSY_CHK | COMMAND_TRANS_SIZE(9) |
> +	       COMMAND_CE(ctrl->cur_cs);
> +
> +	if (buf)
> +		cmd |= COMMAND_A_VALID;
> +	if (oob_buf)
> +		cmd |= COMMAND_B_VALID;
> +
> +	if (read)
> +		cmd |= COMMAND_RX;
> +	else
> +		cmd |= COMMAND_TX | COMMAND_AFT_DAT;
> +
> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> +
> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> +					     msecs_to_jiffies(500));
> +	if (!ret) {
> +		dev_err(ctrl->dev, "COMMAND timeout\n");
> +		tegra_nand_dump_reg(ctrl);
> +		tegra_nand_controller_abort(ctrl);
> +		ret = -ETIMEDOUT;
> +		goto err_unmap_dma;
> +	}
> +
> +	ret = wait_for_completion_io_timeout(&ctrl->dma_complete,
> +					     msecs_to_jiffies(500));
> +	if (!ret) {
> +		dev_err(ctrl->dev, "DMA timeout\n");
> +		tegra_nand_dump_reg(ctrl);
> +		tegra_nand_controller_abort(ctrl);
> +		ret = -ETIMEDOUT;
> +		goto err_unmap_dma;
> +	}
> +	ret = 0;
> +
> +err_unmap_dma:
> +	if (oob_buf)
> +		dma_unmap_single(ctrl->dev, dma_addr_oob, mtd->oobsize, dir);
> +err_unmap_dma_page:
> +	if (buf)
> +		dma_unmap_single(ctrl->dev, dma_addr, mtd->writesize, dir);
> +
> +	return ret;
> +}
> +
> +static int tegra_nand_read_page_raw(struct mtd_info *mtd,
> +				    struct nand_chip *chip,
> +				    uint8_t *buf, int oob_required, int page)
> +{
> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
> +
> +	return tegra_nand_page_xfer(mtd, chip, buf, oob_buf,
> +				    mtd->oobsize, page, true);
> +}
> +
> +static int tegra_nand_write_page_raw(struct mtd_info *mtd,
> +				     struct nand_chip *chip,
> +				     const uint8_t *buf, int oob_required,
> +				     int page)
> +{
> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
> +
> +	return tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf,
> +				     mtd->oobsize, page, false);
> +}
> +
> +static int tegra_nand_read_oob(struct mtd_info *mtd, struct nand_chip
> *chip, +			       int page)
> +{
> +	return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi,
> +				    mtd->oobsize, page, true);
> +}
> +
> +static int tegra_nand_write_oob(struct mtd_info *mtd, struct nand_chip
> *chip, +				int page)
> +{
> +	return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi,
> +				    mtd->oobsize, page, false);
> +}
> +
> +static int tegra_nand_read_page_hwecc(struct mtd_info *mtd,
> +				      struct nand_chip *chip,
> +				      uint8_t *buf, int oob_required, int page)
> +{
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
> +	u32 dec_stat, max_corr_cnt;
> +	unsigned long fail_sec_flag;
> +	int ret;
> +
> +	tegra_nand_hw_ecc(ctrl, chip, true);
> +	ret = tegra_nand_page_xfer(mtd, chip, buf, oob_buf, nand->tag.length,
> +				   page, true);
> +	tegra_nand_hw_ecc(ctrl, chip, false);
> +	if (ret)
> +		return ret;
> +
> +	/* No correctable or un-correctable errors, page must have 0 bitflips */
> +	if (!ctrl->last_read_error)
> +		return 0;
> +
> +	/*
> +	 * Correctable or un-correctable errors occurred. Use DEC_STAT_BUF
> +	 * which contains information for all ECC selections.
> +	 *
> +	 * Note that since we do not use Command Queues DEC_RESULT does not
> +	 * state the number of pages we can read from the DEC_STAT_BUF. But
> +	 * since CORRFAIL_ERR did occur during page read we do have a valid
> +	 * result in DEC_STAT_BUF.
> +	 */
> +	ctrl->last_read_error = false;
> +	dec_stat = readl_relaxed(ctrl->regs + DEC_STAT_BUF);
> +
> +	fail_sec_flag = (dec_stat & DEC_STAT_BUF_FAIL_SEC_FLAG_MASK) >>
> +			DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT;
> +
> +	max_corr_cnt = (dec_stat & DEC_STAT_BUF_MAX_CORR_CNT_MASK) >>
> +		       DEC_STAT_BUF_MAX_CORR_CNT_SHIFT;
> +
> +	if (fail_sec_flag) {
> +		int bit, max_bitflips = 0;
> +
> +		/*
> +		 * Check if all sectors in a page failed. If only some failed
> +		 * its definitly not an erased page and we can return error
> +		 * stats right away.
> +		 *
> +		 * E.g. controller might return fail_sec_flag with 0x4, which
> +		 * would mean only the third sector failed to correct.
> +		 */
> +		if (fail_sec_flag ^ GENMASK(chip->ecc.steps - 1, 0)) {
> +			mtd->ecc_stats.failed += hweight8(fail_sec_flag);
> +			return max_corr_cnt;
> +		}
> +
> +		/*
> +		 * All sectors failed to correct, but the ECC isn't smart
> +		 * enough to figure out if a page is really completely erased.
> +		 * We check the read data here to figure out if it's a
> +		 * legitimate ECC error or only an erased page.
> +		 */
> +		for_each_set_bit(bit, &fail_sec_flag, chip->ecc.steps) {
> +			u8 *data = buf + (chip->ecc.size * bit);
> +
> +			ret = nand_check_erased_ecc_chunk(data, chip->ecc.size,
> +							  NULL, 0,
> +							  NULL, 0,
> +							  chip->ecc.strength);
> +			if (ret < 0)
> +				mtd->ecc_stats.failed++;
> +			else
> +				max_bitflips = max(ret, max_bitflips);
> +		}
> +
> +		return max_t(unsigned int, max_corr_cnt, max_bitflips);
> +	} else {
> +		int corr_sec_flag;
> +
> +		corr_sec_flag = (dec_stat & DEC_STAT_BUF_CORR_SEC_FLAG_MASK) >>
> +				DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT;
> +
> +		/*
> +		 * The value returned in the register is the maximum of
> +		 * bitflips encountered in any of the ECC regions. As there is
> +		 * no way to get the number of bitflips in a specific regions
> +		 * we are not able to deliver correct stats but instead
> +		 * overestimate the number of corrected bitflips by assuming
> +		 * that all regions where errors have been corrected
> +		 * encountered the maximum number of bitflips.
> +		 */
> +		mtd->ecc_stats.corrected += max_corr_cnt * hweight8(corr_sec_flag);
> +
> +		return max_corr_cnt;
> +	}
> +

Blank line isn't needed here.

> +}
> +
> +static int tegra_nand_write_page_hwecc(struct mtd_info *mtd,
> +				       struct nand_chip *chip,
> +				       const uint8_t *buf, int oob_required,
> +				       int page)
> +{
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
> +	int ret;
> +
> +	tegra_nand_hw_ecc(ctrl, chip, true);
> +	ret = tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf,
> +				   nand->tag.length, page, false);
> +	tegra_nand_hw_ecc(ctrl, chip, false);
> +
> +	return ret;
> +}
> +
> +static void tegra_nand_setup_timing(struct tegra_nand_controller *ctrl,
> +				    const struct nand_sdr_timings *timings)
> +{
> +	/*
> +	 * The period (and all other timings in this function) is in ps,
> +	 * so need to take care here to avoid integer overflows.
> +	 */
> +	unsigned int rate = clk_get_rate(ctrl->clk) / 1000000;
> +	unsigned int period = DIV_ROUND_UP(1000000, rate);
> +	u32 val, reg = 0;
> +
> +	val = DIV_ROUND_UP(max3(timings->tAR_min, timings->tRR_min,
> +				timings->tRC_min), period);
> +	reg |= TIMING_TCR_TAR_TRR(OFFSET(val, 3));
> +
> +	val = DIV_ROUND_UP(max(max(timings->tCS_min, timings->tCH_min),
> +			       max(timings->tALS_min, timings->tALH_min)),
> +			   period);
> +	reg |= TIMING_TCS(OFFSET(val, 2));
> +
> +	val = DIV_ROUND_UP(max(timings->tRP_min, timings->tREA_max) + 6000,
> +			   period);
> +	reg |= TIMING_TRP(OFFSET(val, 1)) | TIMING_TRP_RESP(OFFSET(val, 1));
> +
> +	reg |= TIMING_TWB(OFFSET(DIV_ROUND_UP(timings->tWB_max, period), 1));
> +	reg |= TIMING_TWHR(OFFSET(DIV_ROUND_UP(timings->tWHR_min, period), 1));
> +	reg |= TIMING_TWH(OFFSET(DIV_ROUND_UP(timings->tWH_min, period), 1));
> +	reg |= TIMING_TWP(OFFSET(DIV_ROUND_UP(timings->tWP_min, period), 1));
> +	reg |= TIMING_TRH(OFFSET(DIV_ROUND_UP(timings->tREH_min, period), 1));
> +
> +	writel_relaxed(reg, ctrl->regs + TIMING_1);
> +
> +	val = DIV_ROUND_UP(timings->tADL_min, period);
> +	reg = TIMING_TADL(OFFSET(val, 3));
> +
> +	writel_relaxed(reg, ctrl->regs + TIMING_2);
> +}
> +
> +static int tegra_nand_setup_data_interface(struct mtd_info *mtd, int
> csline, +					const struct nand_data_interface *conf)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +	const struct nand_sdr_timings *timings;
> +
> +	timings = nand_get_sdr_timings(conf);
> +	if (IS_ERR(timings))
> +		return PTR_ERR(timings);
> +
> +	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
> +		return 0;
> +
> +	tegra_nand_setup_timing(ctrl, timings);
> +
> +	return 0;
> +}
> +
> +static const int rs_strength_bootable[] = { 4 };
> +static const int rs_strength[] = { 4, 6, 8 };
> +static const int bch_strength_bootable[] = { 8, 16 };
> +static const int bch_strength[] = { 4, 8, 14, 16 };
> +
> +static int tegra_nand_get_strength(struct nand_chip *chip, const int
> *strength, +				   int strength_len, int oobsize)
> +{
> +	bool maximize = chip->ecc.options & NAND_ECC_MAXIMIZE;
> +	int i;
> +
> +	/*
> +	 * Loop through available strengths. Backwards in case we try to
> +	 * maximize the BCH strength.
> +	 */
> +	for (i = 0; i < strength_len; i++) {
> +		int strength_sel, bytes_per_step, bytes_per_page;
> +
> +		if (maximize) {
> +			strength_sel = strength[strength_len - i - 1];
> +		} else {
> +			strength_sel = strength[i];
> +
> +			if (strength_sel < chip->ecc_strength_ds)
> +				continue;
> +		}
> +
> +		bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * strength_sel,
> +					      BITS_PER_BYTE);
> +		bytes_per_page = round_up(bytes_per_step * chip->ecc.steps, 4);
> +
> +		/* Check whether strength fits OOB */
> +		if (bytes_per_page < (oobsize - SKIP_SPARE_BYTES))
> +			return strength_sel;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int tegra_nand_select_strength(struct nand_chip *chip, int oobsize)
> +{
> +	const int *strength;
> +	int strength_len;
> +
> +	switch (chip->ecc.algo) {
> +	case NAND_ECC_RS:
> +		if (chip->options & NAND_IS_BOOT_MEDIUM) {
> +			strength = rs_strength_bootable;
> +			strength_len = ARRAY_SIZE(rs_strength_bootable);
> +		} else {
> +			strength = rs_strength;
> +			strength_len = ARRAY_SIZE(rs_strength);
> +		}
> +		break;
> +	case NAND_ECC_BCH:
> +		if (chip->options & NAND_IS_BOOT_MEDIUM) {
> +			strength = bch_strength_bootable;
> +			strength_len = ARRAY_SIZE(bch_strength_bootable);
> +		} else {
> +			strength = bch_strength;
> +			strength_len = ARRAY_SIZE(bch_strength);
> +		}
> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	return tegra_nand_get_strength(chip, strength, strength_len, oobsize);
> +}
> +
> +static int tegra_nand_chips_init(struct device *dev,
> +				 struct tegra_nand_controller *ctrl)
> +{
> +	struct device_node *np = dev->of_node;
> +	struct device_node *np_nand;
> +	int nsels, nchips = of_get_child_count(np);
> +	struct tegra_nand_chip *nand;
> +	struct mtd_info *mtd;
> +	struct nand_chip *chip;
> +	int bits_per_step;
> +	int ret;
> +	u32 cs;
> +
> +	if (nchips != 1) {
> +		dev_err(dev, "Currently only one NAND chip supported\n");
> +		return -EINVAL;
> +	}
> +
> +	np_nand = of_get_next_child(np, NULL);
> +
> +	nsels = of_property_count_elems_of_size(np_nand, "reg", sizeof(u32));
> +	if (nsels != 1) {
> +		dev_err(dev, "Missing/invalid reg property\n");
> +		return -EINVAL;
> +	}
> +
> +	/* Retrieve CS id, currently only single die NAND supported */
> +	ret = of_property_read_u32(np_nand, "reg", &cs);
> +	if (ret) {
> +		dev_err(dev, "could not retrieve reg property: %d\n", ret);
> +		return ret;
> +	}
> +
> +	nand = devm_kzalloc(dev, sizeof(*nand), GFP_KERNEL);
> +	if (!nand)
> +		return -ENOMEM;
> +
> +	nand->cs[0] = cs;
> +
> +	nand->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_LOW);
> +
> +	if (IS_ERR(nand->wp_gpio)) {
> +		ret = PTR_ERR(nand->wp_gpio);
> +		dev_err(dev, "Failed to request WP GPIO: %d\n", ret);
> +		return ret;
> +	}
> +
> +	chip = &nand->chip;
> +	chip->controller = &ctrl->controller;
> +
> +	mtd = nand_to_mtd(chip);
> +
> +	mtd->dev.parent = dev;
> +	mtd->owner = THIS_MODULE;
> +
> +	nand_set_flash_node(chip, np_nand);
> +
> +	if (!mtd->name)
> +		mtd->name = "tegra_nand";
> +
> +	chip->options = NAND_NO_SUBPAGE_WRITE | NAND_USE_BOUNCE_BUFFER;
> +	chip->exec_op = tegra_nand_exec_op;
> +	chip->select_chip = tegra_nand_select_chip;
> +	chip->setup_data_interface = tegra_nand_setup_data_interface;
> +
> +	ret = nand_scan_ident(mtd, 1, NULL);
> +	if (ret)
> +		return ret;
> +
> +	if (chip->bbt_options & NAND_BBT_USE_FLASH)
> +		chip->bbt_options |= NAND_BBT_NO_OOB;
> +
> +	chip->ecc.mode = NAND_ECC_HW;
> +	chip->ecc.size = 512;
> +	chip->ecc.steps = mtd->writesize / chip->ecc.size;
> +	if (chip->ecc_step_ds != 512) {
> +		dev_err(dev, "Unsupported step size %d\n", chip->ecc_step_ds);
> +		return -EINVAL;
> +	}
> +
> +	chip->ecc.read_page = tegra_nand_read_page_hwecc;
> +	chip->ecc.write_page = tegra_nand_write_page_hwecc;
> +	chip->ecc.read_page_raw = tegra_nand_read_page_raw;
> +	chip->ecc.write_page_raw = tegra_nand_write_page_raw;
> +	chip->ecc.read_oob = tegra_nand_read_oob;
> +	chip->ecc.write_oob = tegra_nand_write_oob;
> +
> +	if (chip->options & NAND_BUSWIDTH_16)
> +		nand->config |= CONFIG_BUS_WIDTH_16;
> +
> +	if (chip->ecc.algo == NAND_ECC_UNKNOWN) {
> +		if (mtd->writesize < 2048)
> +			chip->ecc.algo = NAND_ECC_RS;
> +		else
> +			chip->ecc.algo = NAND_ECC_BCH;
> +	}
> +
> +	if (chip->ecc.algo == NAND_ECC_BCH && mtd->writesize < 2048) {
> +		dev_err(dev, "BCH supportes 2K or 4K page size only\n");
> +		return -EINVAL;
> +	}
> +
> +	if (!chip->ecc.strength) {
> +		ret = tegra_nand_select_strength(chip, mtd->oobsize);
> +		if (ret < 0) {
> +			dev_err(dev, "No valid strenght found, minimum %d\n",
> +				chip->ecc_strength_ds);
> +			return ret;
> +		}
> +
> +		chip->ecc.strength = ret;
> +	}
> +
> +	nand->config_ecc = CONFIG_PIPE_EN | CONFIG_SKIP_SPARE |
> +			   CONFIG_SKIP_SPARE_SIZE_4;
> +
> +	switch (chip->ecc.algo) {
> +	case NAND_ECC_RS:
> +		bits_per_step = BITS_PER_STEP_RS * chip->ecc.strength;
> +		mtd_set_ooblayout(mtd, &tegra_nand_oob_rs_ops);
> +		nand->config_ecc |= CONFIG_HW_ECC | CONFIG_ECC_SEL |
> +				    CONFIG_ERR_COR;
> +		switch (chip->ecc.strength) {
> +		case 4:
> +			nand->config_ecc |= CONFIG_TVAL_4;
> +			break;
> +		case 6:
> +			nand->config_ecc |= CONFIG_TVAL_6;
> +			break;
> +		case 8:
> +			nand->config_ecc |= CONFIG_TVAL_8;
> +			break;
> +		default:
> +			dev_err(dev, "ECC strength %d not supported\n",
> +				chip->ecc.strength);
> +			return -EINVAL;
> +		}
> +		break;
> +	case NAND_ECC_BCH:
> +		bits_per_step = BITS_PER_STEP_BCH * chip->ecc.strength;
> +		mtd_set_ooblayout(mtd, &tegra_nand_oob_bch_ops);
> +		nand->bch_config = BCH_ENABLE;
> +		switch (chip->ecc.strength) {
> +		case 4:
> +			nand->bch_config |= BCH_TVAL_4;
> +			break;
> +		case 8:
> +			nand->bch_config |= BCH_TVAL_8;
> +			break;
> +		case 14:
> +			nand->bch_config |= BCH_TVAL_14;
> +			break;
> +		case 16:
> +			nand->bch_config |= BCH_TVAL_16;
> +			break;
> +		default:
> +			dev_err(dev, "ECC strength %d not supported\n",
> +				chip->ecc.strength);
> +			return -EINVAL;
> +		}
> +		break;
> +	default:
> +		dev_err(dev, "ECC algorithm not supported\n");
> +		return -EINVAL;
> +	}
> +
> +	dev_info(dev, "Using %s with strength %d per 512 byte step\n",
> +			chip->ecc.algo == NAND_ECC_BCH ? "BCH" : "RS",
> +			chip->ecc.strength);
> +
> +	chip->ecc.bytes = DIV_ROUND_UP(bits_per_step, BITS_PER_BYTE);
> +
> +	switch (mtd->writesize) {
> +	case 256:
> +		nand->config |= CONFIG_PS_256;
> +		break;
> +	case 512:
> +		nand->config |= CONFIG_PS_512;
> +		break;
> +	case 1024:
> +		nand->config |= CONFIG_PS_1024;
> +		break;
> +	case 2048:
> +		nand->config |= CONFIG_PS_2048;
> +		break;
> +	case 4096:
> +		nand->config |= CONFIG_PS_4096;
> +		break;
> +	default:
> +		dev_err(dev, "Unsupported writesize %d\n", mtd->writesize);
> +		return -ENODEV;
> +	}
> +
> +	/* Store complete configuration in config_ecc */
> +	nand->config_ecc |= nand->config;
> +
> +	/* Non-HW ECC read/writes complete OOB */
> +	nand->config |= CONFIG_TAG_BYTE_SIZE(mtd->oobsize - 1);
> +	writel_relaxed(nand->config, ctrl->regs + CONFIG);
> +
> +	ret = nand_scan_tail(mtd);
> +	if (ret)
> +		return ret;
> +
> +	/* Store tag layout when using HW ECC */
> +	mtd_ooblayout_free(mtd, 0, &nand->tag);
> +	nand->config_ecc |= CONFIG_TAG_BYTE_SIZE(nand->tag.length - 1);
> +
> +	ret = mtd_device_register(mtd, NULL, 0);
> +	if (ret) {
> +		dev_err(dev, "Failed to register mtd device: %d\n", ret);
> +		nand_cleanup(chip);
> +		return ret;
> +	}
> +
> +	ctrl->chip = chip;
> +
> +	return 0;
> +}
> +
> +static int tegra_nand_probe(struct platform_device *pdev)
> +{
> +	struct reset_control *rst;
> +	struct tegra_nand_controller *ctrl;
> +	struct resource *res;
> +	int err = 0;
> +
> +	ctrl = devm_kzalloc(&pdev->dev, sizeof(*ctrl), GFP_KERNEL);
> +	if (!ctrl)
> +		return -ENOMEM;
> +
> +	ctrl->dev = &pdev->dev;
> +	nand_hw_control_init(&ctrl->controller);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	ctrl->regs = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(ctrl->regs))
> +		return PTR_ERR(ctrl->regs);
> +
> +	rst = devm_reset_control_get(&pdev->dev, "nand");
> +	if (IS_ERR(rst))
> +		return PTR_ERR(rst);
> +
> +	ctrl->clk = devm_clk_get(&pdev->dev, "nand");
> +	if (IS_ERR(ctrl->clk))
> +		return PTR_ERR(ctrl->clk);
> +
> +	err = clk_prepare_enable(ctrl->clk);
> +	if (err)
> +		return err;
> +
> +	err = reset_control_reset(rst);
> +	if (err) {
> +		dev_err(ctrl->dev, "Failed to reset HW: %d\n", err);
> +		goto err_disable_clk;
> +	}
> +
> +	writel_relaxed(HWSTATUS_CMD_DEFAULT, ctrl->regs + HWSTATUS_CMD);
> +	writel_relaxed(HWSTATUS_MASK_DEFAULT, ctrl->regs + HWSTATUS_MASK);
> +	writel_relaxed(INT_MASK, ctrl->regs + IER);
> +
> +	init_completion(&ctrl->command_complete);
> +	init_completion(&ctrl->dma_complete);
> +
> +	ctrl->irq = platform_get_irq(pdev, 0);
> +	err = devm_request_irq(&pdev->dev, ctrl->irq, tegra_nand_irq, 0,
> +			       dev_name(&pdev->dev), ctrl);
> +	if (err) {
> +		dev_err(ctrl->dev, "Failed to get IRQ: %d\n", err);
> +		goto err_disable_clk;
> +	}
> +
> +	writel_relaxed(DMA_MST_CTRL_IS_DONE, ctrl->regs + DMA_MST_CTRL);
> +
> +	err = tegra_nand_chips_init(ctrl->dev, ctrl);
> +	if (err)
> +		goto err_disable_clk;
> +
> +	platform_set_drvdata(pdev, ctrl);
> +
> +	return 0;
> +
> +err_disable_clk:
> +	clk_disable_unprepare(ctrl->clk);
> +	return err;
> +}
> +
> +static int tegra_nand_remove(struct platform_device *pdev)
> +{
> +	struct tegra_nand_controller *ctrl = platform_get_drvdata(pdev);
> +
> +	nand_release(nand_to_mtd(ctrl->chip));
> +
> +	clk_disable_unprepare(ctrl->clk);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id tegra_nand_of_match[] = {
> +	{ .compatible = "nvidia,tegra20-nand" },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, tegra_nand_of_match);
> +
> +static struct platform_driver tegra_nand_driver = {
> +	.driver = {
> +		.name = "tegra-nand",
> +		.of_match_table = tegra_nand_of_match,
> +	},
> +	.probe = tegra_nand_probe,
> +	.remove = tegra_nand_remove,
> +};
> +module_platform_driver(tegra_nand_driver);
> +
> +MODULE_DESCRIPTION("NVIDIA Tegra NAND driver");
> +MODULE_AUTHOR("Thierry Reding <thierry.reding@nvidia.com>");
> +MODULE_AUTHOR("Lucas Stach <dev@lynxeye.de>");
> +MODULE_AUTHOR("Stefan Agner <stefan@agner.ch>");
> +MODULE_LICENSE("GPL v2");





^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
  2018-06-11 23:08   ` kbuild test robot
  2018-06-11 23:32   ` Dmitry Osipenko
@ 2018-06-12  0:03   ` Dmitry Osipenko
  2018-06-12  8:06     ` Stefan Agner
  2018-06-12 12:17   ` Dmitry Osipenko
  3 siblings, 1 reply; 24+ messages in thread
From: Dmitry Osipenko @ 2018-06-12  0:03 UTC (permalink / raw)
  To: Stefan Agner
  Cc: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
> Add support for the NAND flash controller found on NVIDIA
> Tegra 2 SoCs. This implementation does not make use of the
> command queue feature. Regular operations/data transfers are
> done in PIO mode. Page read/writes with hardware ECC make
> use of the DMA for data transfer.
> 
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
>  MAINTAINERS                       |    7 +
>  drivers/mtd/nand/raw/Kconfig      |    6 +
>  drivers/mtd/nand/raw/Makefile     |    1 +
>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>  4 files changed, 1262 insertions(+)
>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 58b9861ccf99..c2e5571c85d4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13844,6 +13844,13 @@ M:	Laxman Dewangan <ldewangan@nvidia.com>
>  S:	Supported
>  F:	drivers/input/keyboard/tegra-kbc.c
> 
> +TEGRA NAND DRIVER
> +M:	Stefan Agner <stefan@agner.ch>
> +M:	Lucas Stach <dev@lynxeye.de>
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
> +F:	drivers/mtd/nand/raw/tegra_nand.c
> +
>  TEGRA PWM DRIVER
>  M:	Thierry Reding <thierry.reding@gmail.com>
>  S:	Supported
> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
> index 19a2b283fbbe..e9093f52371e 100644
> --- a/drivers/mtd/nand/raw/Kconfig
> +++ b/drivers/mtd/nand/raw/Kconfig
> @@ -534,4 +534,10 @@ config MTD_NAND_MTK
>  	  Enables support for NAND controller on MTK SoCs.
>  	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
> 
> +config MTD_NAND_TEGRA
> +	tristate "Support for NAND controller on NVIDIA Tegra"
> +	depends on ARCH_TEGRA || COMPILE_TEST
> +	help
> +	  Enables support for NAND flash controller on NVIDIA Tegra SoC.
> +
>  endif # MTD_NAND
> diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
> index 165b7ef9e9a1..d5a5f9832b88 100644
> --- a/drivers/mtd/nand/raw/Makefile
> +++ b/drivers/mtd/nand/raw/Makefile
> @@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504)	        += 
hisi504_nand.o
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
>  obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
>  obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
> +obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
> 
>  nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
>  nand-objs += nand_amd.o
> diff --git a/drivers/mtd/nand/raw/tegra_nand.c
> b/drivers/mtd/nand/raw/tegra_nand.c new file mode 100644
> index 000000000000..dd23a5eb6af3
> --- /dev/null
> +++ b/drivers/mtd/nand/raw/tegra_nand.c
> @@ -0,0 +1,1248 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2018 Stefan Agner <stefan@agner.ch>
> + * Copyright (C) 2014-2015 Lucas Stach <dev@lynxeye.de>
> + * Copyright (C) 2012 Avionic Design GmbH
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/err.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/mtd/partitions.h>
> +#include <linux/mtd/rawnand.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +
> +#define COMMAND					0x00
> +#define   COMMAND_GO				BIT(31)
> +#define   COMMAND_CLE				BIT(30)
> +#define   COMMAND_ALE				BIT(29)
> +#define   COMMAND_PIO				BIT(28)
> +#define   COMMAND_TX				BIT(27)
> +#define   COMMAND_RX				BIT(26)
> +#define   COMMAND_SEC_CMD			BIT(25)
> +#define   COMMAND_AFT_DAT			BIT(24)
> +#define   COMMAND_TRANS_SIZE(x)			(((x - 1) & 0xf) << 20)
> +#define   COMMAND_A_VALID			BIT(19)
> +#define   COMMAND_B_VALID			BIT(18)
> +#define   COMMAND_RD_STATUS_CHK			BIT(17)
> +#define   COMMAND_RBSY_CHK			BIT(16)
> +#define   COMMAND_CE(x)				BIT(8 + ((x) & 0x7))
> +#define   COMMAND_CLE_SIZE(x)			(((x - 1) & 0x3) << 4)
> +#define   COMMAND_ALE_SIZE(x)			(((x - 1) & 0xf) << 0)
> +
> +#define STATUS					0x04
> +
> +#define ISR					0x08
> +#define   ISR_CORRFAIL_ERR			BIT(24)
> +#define   ISR_UND				BIT(7)
> +#define   ISR_OVR				BIT(6)
> +#define   ISR_CMD_DONE				BIT(5)
> +#define   ISR_ECC_ERR				BIT(4)
> +
> +#define IER					0x0c
> +#define   IER_ERR_TRIG_VAL(x)			(((x) & 0xf) << 16)
> +#define   IER_UND				BIT(7)
> +#define   IER_OVR				BIT(6)
> +#define   IER_CMD_DONE				BIT(5)
> +#define   IER_ECC_ERR				BIT(4)
> +#define   IER_GIE				BIT(0)
> +
> +#define CONFIG					0x10
> +#define   CONFIG_HW_ECC				BIT(31)
> +#define   CONFIG_ECC_SEL			BIT(30)
> +#define   CONFIG_ERR_COR			BIT(29)
> +#define   CONFIG_PIPE_EN			BIT(28)
> +#define   CONFIG_TVAL_4				(0 << 24)
> +#define   CONFIG_TVAL_6				(1 << 24)
> +#define   CONFIG_TVAL_8				(2 << 24)
> +#define   CONFIG_SKIP_SPARE			BIT(23)
> +#define   CONFIG_BUS_WIDTH_16			BIT(21)
> +#define   CONFIG_COM_BSY			BIT(20)
> +#define   CONFIG_PS_256				(0 << 16)
> +#define   CONFIG_PS_512				(1 << 16)
> +#define   CONFIG_PS_1024			(2 << 16)
> +#define   CONFIG_PS_2048			(3 << 16)
> +#define   CONFIG_PS_4096			(4 << 16)
> +#define   CONFIG_SKIP_SPARE_SIZE_4		(0 << 14)
> +#define   CONFIG_SKIP_SPARE_SIZE_8		(1 << 14)
> +#define   CONFIG_SKIP_SPARE_SIZE_12		(2 << 14)
> +#define   CONFIG_SKIP_SPARE_SIZE_16		(3 << 14)
> +#define   CONFIG_TAG_BYTE_SIZE(x)			((x) & 0xff)
> +
> +#define TIMING_1				0x14
> +#define   TIMING_TRP_RESP(x)			(((x) & 0xf) << 28)
> +#define   TIMING_TWB(x)				(((x) & 0xf) << 24)
> +#define   TIMING_TCR_TAR_TRR(x)			(((x) & 0xf) << 20)
> +#define   TIMING_TWHR(x)			(((x) & 0xf) << 16)
> +#define   TIMING_TCS(x)				(((x) & 0x3) << 14)
> +#define   TIMING_TWH(x)				(((x) & 0x3) << 12)
> +#define   TIMING_TWP(x)				(((x) & 0xf) <<  8)
> +#define   TIMING_TRH(x)				(((x) & 0x3) <<  4)
> +#define   TIMING_TRP(x)				(((x) & 0xf) <<  0)
> +
> +#define RESP					0x18
> +
> +#define TIMING_2				0x1c
> +#define   TIMING_TADL(x)			((x) & 0xf)
> +
> +#define CMD_REG1				0x20
> +#define CMD_REG2				0x24
> +#define ADDR_REG1				0x28
> +#define ADDR_REG2				0x2c
> +
> +#define DMA_MST_CTRL				0x30
> +#define   DMA_MST_CTRL_GO			BIT(31)
> +#define   DMA_MST_CTRL_IN			(0 << 30)
> +#define   DMA_MST_CTRL_OUT			BIT(30)
> +#define   DMA_MST_CTRL_PERF_EN			BIT(29)
> +#define   DMA_MST_CTRL_IE_DONE			BIT(28)
> +#define   DMA_MST_CTRL_REUSE			BIT(27)
> +#define   DMA_MST_CTRL_BURST_1			(2 << 24)
> +#define   DMA_MST_CTRL_BURST_4			(3 << 24)
> +#define   DMA_MST_CTRL_BURST_8			(4 << 24)
> +#define   DMA_MST_CTRL_BURST_16			(5 << 24)
> +#define   DMA_MST_CTRL_IS_DONE			BIT(20)
> +#define   DMA_MST_CTRL_EN_A			BIT(2)
> +#define   DMA_MST_CTRL_EN_B			BIT(1)
> +
> +#define DMA_CFG_A				0x34
> +#define DMA_CFG_B				0x38
> +
> +#define FIFO_CTRL				0x3c
> +#define   FIFO_CTRL_CLR_ALL			BIT(3)
> +
> +#define DATA_PTR				0x40
> +#define TAG_PTR					0x44
> +#define ECC_PTR					0x48
> +
> +#define DEC_STATUS				0x4c
> +#define   DEC_STATUS_A_ECC_FAIL			BIT(1)
> +#define   DEC_STATUS_ERR_COUNT_MASK		0x00ff0000
> +#define   DEC_STATUS_ERR_COUNT_SHIFT		16
> +
> +#define HWSTATUS_CMD				0x50
> +#define HWSTATUS_MASK				0x54
> +#define   HWSTATUS_RDSTATUS_MASK(x)		(((x) & 0xff) << 24)
> +#define   HWSTATUS_RDSTATUS_VALUE(x)		(((x) & 0xff) << 16)
> +#define   HWSTATUS_RBSY_MASK(x)			(((x) & 0xff) << 8)
> +#define   HWSTATUS_RBSY_VALUE(x)		(((x) & 0xff) << 0)
> +
> +#define BCH_CONFIG				0xcc
> +#define   BCH_ENABLE				BIT(0)
> +#define   BCH_TVAL_4				(0 << 4)
> +#define   BCH_TVAL_8				(1 << 4)
> +#define   BCH_TVAL_14				(2 << 4)
> +#define   BCH_TVAL_16				(3 << 4)
> +
> +#define DEC_STAT_RESULT				0xd0
> +#define DEC_STAT_BUF				0xd4
> +#define   DEC_STAT_BUF_FAIL_SEC_FLAG_MASK	0xff000000
> +#define   DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT	24
> +#define   DEC_STAT_BUF_CORR_SEC_FLAG_MASK	0x00ff0000
> +#define   DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT	16
> +#define   DEC_STAT_BUF_MAX_CORR_CNT_MASK	0x00001f00
> +#define   DEC_STAT_BUF_MAX_CORR_CNT_SHIFT	8
> +
> +#define OFFSET(val, off)	((val) < (off) ? 0 : (val) - (off))
> +
> +#define SKIP_SPARE_BYTES	4
> +#define BITS_PER_STEP_RS	18
> +#define BITS_PER_STEP_BCH	13
> +
> +#define INT_MASK		(IER_UND | IER_OVR | IER_CMD_DONE | IER_GIE)
> +#define HWSTATUS_CMD_DEFAULT	NAND_STATUS_READY
> +#define HWSTATUS_MASK_DEFAULT	(HWSTATUS_RDSTATUS_MASK(1) | \
> +				HWSTATUS_RDSTATUS_VALUE(0) | \
> +				HWSTATUS_RBSY_MASK(NAND_STATUS_READY) | \
> +				HWSTATUS_RBSY_VALUE(NAND_STATUS_READY))
> +
> +struct tegra_nand_controller {
> +	struct nand_hw_control controller;
> +	struct device *dev;
> +	void __iomem *regs;
> +	int irq;
> +	struct clk *clk;
> +	struct completion command_complete;
> +	struct completion dma_complete;
> +	bool last_read_error;
> +	int cur_cs;
> +	struct nand_chip *chip;
> +};
> +
> +struct tegra_nand_chip {
> +	struct nand_chip chip;
> +	struct gpio_desc *wp_gpio;
> +	struct mtd_oob_region tag;
> +	u32 config;
> +	u32 config_ecc;
> +	u32 bch_config;
> +	int cs[1];
> +};
> +
> +static inline struct tegra_nand_controller *to_tegra_ctrl(
> +						struct nand_hw_control *hw_ctrl)
> +{
> +	return container_of(hw_ctrl, struct tegra_nand_controller, controller);
> +}
> +
> +static inline struct tegra_nand_chip *to_tegra_chip(struct nand_chip *chip)
> +{
> +	return container_of(chip, struct tegra_nand_chip, chip);
> +}
> +
> +static int tegra_nand_ooblayout_rs_ecc(struct mtd_info *mtd, int section,
> +				       struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES;
> +	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
> +
> +	return 0;
> +}
> +
> +static int tegra_nand_ooblayout_rs_free(struct mtd_info *mtd, int section,
> +					struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES +
> +			    round_up(bytes_per_step * chip->ecc.steps, 4);
> +	oobregion->length = mtd->oobsize - oobregion->offset;
> +
> +	return 0;
> +}
> +
> +static const struct mtd_ooblayout_ops tegra_nand_oob_rs_ops = {
> +	.ecc = tegra_nand_ooblayout_rs_ecc,
> +	.free = tegra_nand_ooblayout_rs_free,
> +};
> +
> +static int tegra_nand_ooblayout_bch_ecc(struct mtd_info *mtd, int section,
> +				       struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES;
> +	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
> +
> +	return 0;
> +}
> +
> +static int tegra_nand_ooblayout_bch_free(struct mtd_info *mtd, int section,
> +					struct mtd_oob_region *oobregion)
> +{
> +	struct nand_chip *chip = mtd_to_nand(mtd);
> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
> +					  BITS_PER_BYTE);
> +
> +	if (section > 0)
> +		return -ERANGE;
> +
> +	oobregion->offset = SKIP_SPARE_BYTES +
> +			    round_up(bytes_per_step * chip->ecc.steps, 4);
> +	oobregion->length = mtd->oobsize - oobregion->offset;
> +
> +	return 0;
> +}
> +
> +/*
> + * Layout with tag bytes is
> + *
> + *
> --------------------------------------------------------------------------
> + * | main area                       | skip bytes | tag bytes | parity |
> .. | + *
> --------------------------------------------------------------------------
> + *
> + * If not tag bytes are written, parity moves right after skip bytes!
> + */
> +static const struct mtd_ooblayout_ops tegra_nand_oob_bch_ops = {
> +	.ecc = tegra_nand_ooblayout_bch_ecc,
> +	.free = tegra_nand_ooblayout_bch_free,
> +};
> +
> +static irqreturn_t tegra_nand_irq(int irq, void *data)
> +{
> +	struct tegra_nand_controller *ctrl = data;
> +	u32 isr, dma;
> +
> +	isr = readl_relaxed(ctrl->regs + ISR);
> +	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
> +	dev_dbg(ctrl->dev, "isr %08x\n", isr);
> +
> +	if (!isr && !(dma & DMA_MST_CTRL_IS_DONE))
> +		return IRQ_NONE;
> +
> +	/*
> +	 * The bit name is somewhat missleading: This is also set when
> +	 * HW ECC was successful. The data sheet states:
> +	 * Correctable OR Un-correctable errors occurred in the DMA transfer...
> +	 */
> +	if (isr & ISR_CORRFAIL_ERR)
> +		ctrl->last_read_error = true;
> +
> +	if (isr & ISR_CMD_DONE)
> +		complete(&ctrl->command_complete);
> +
> +	if (isr & ISR_UND)
> +		dev_err(ctrl->dev, "FIFO underrun\n");
> +
> +	if (isr & ISR_OVR)
> +		dev_err(ctrl->dev, "FIFO overrun\n");
> +
> +	/* handle DMA interrupts */
> +	if (dma & DMA_MST_CTRL_IS_DONE) {
> +		writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
> +		complete(&ctrl->dma_complete);
> +	}
> +
> +	/* clear interrupts */
> +	writel_relaxed(isr, ctrl->regs + ISR);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static const char * const tegra_nand_reg_names[] = {
> +	"COMMAND",
> +	"STATUS",
> +	"ISR",
> +	"IER",
> +	"CONFIG",
> +	"TIMING",
> +	NULL,
> +	"TIMING2",
> +	"CMD_REG1",
> +	"CMD_REG2",
> +	"ADDR_REG1",
> +	"ADDR_REG2",
> +	"DMA_MST_CTRL",
> +	"DMA_CFG_A",
> +	"DMA_CFG_B",
> +	"FIFO_CTRL",
> +};
> +
> +static void tegra_nand_dump_reg(struct tegra_nand_controller *ctrl)
> +{
> +	u32 reg;
> +	int i;
> +
> +	dev_err(ctrl->dev, "Tegra NAND controller register dump\n");
> +	for (i = 0; i < ARRAY_SIZE(tegra_nand_reg_names); i++) {
> +		const char *reg_name = tegra_nand_reg_names[i];
> +
> +		if (!reg_name)
> +			continue;
> +
> +		reg = readl_relaxed(ctrl->regs + (i * 4));
> +		dev_err(ctrl->dev, "%s: 0x%08x\n", reg_name, reg);
> +	}
> +}
> +
> +static void tegra_nand_controller_abort(struct tegra_nand_controller *ctrl)
> +{
> +	u32 isr, dma;
> +
> +	disable_irq(ctrl->irq);
> +
> +	/* Abort current command/DMA operation */
> +	writel_relaxed(0, ctrl->regs + DMA_MST_CTRL);
> +	writel_relaxed(0, ctrl->regs + COMMAND);
> +
> +	/* clear interrupts */
> +	isr = readl_relaxed(ctrl->regs + ISR);
> +	writel_relaxed(isr, ctrl->regs + ISR);
> +	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
> +	writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
> +
> +	reinit_completion(&ctrl->command_complete);
> +	reinit_completion(&ctrl->dma_complete);
> +
> +	enable_irq(ctrl->irq);
> +}
> +
> +static int tegra_nand_cmd(struct nand_chip *chip,
> +			 const struct nand_subop *subop)
> +{
> +	const struct nand_op_instr *instr;
> +	const struct nand_op_instr *instr_data_in = NULL;
> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> +	unsigned int op_id, size = 0, offset = 0;
> +	bool first_cmd = true;
> +	u32 reg, cmd = 0;
> +	int ret;
> +
> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
> +		unsigned int naddrs, i;
> +		const u8 *addrs;
> +		u32 addr1 = 0, addr2 = 0;
> +
> +		instr = &subop->instrs[op_id];
> +
> +		switch (instr->type) {
> +		case NAND_OP_CMD_INSTR:
> +			if (first_cmd) {
> +				cmd |= COMMAND_CLE;
> +				writel_relaxed(instr->ctx.cmd.opcode,
> +					       ctrl->regs + CMD_REG1);
> +			} else {
> +				cmd |= COMMAND_SEC_CMD;
> +				writel_relaxed(instr->ctx.cmd.opcode,
> +					       ctrl->regs + CMD_REG2);
> +			}
> +			first_cmd = false;
> +			break;
> +		case NAND_OP_ADDR_INSTR:
> +			offset = nand_subop_get_addr_start_off(subop, op_id);
> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
> +			addrs = &instr->ctx.addr.addrs[offset];
> +
> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
> +			naddrs -= i;
> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
> +			break;
> +
> +		case NAND_OP_DATA_IN_INSTR:
> +			size = nand_subop_get_data_len(subop, op_id);
> +			offset = nand_subop_get_data_start_off(subop, op_id);
> +
> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> +				COMMAND_RX | COMMAND_A_VALID;
> +
> +			instr_data_in = instr;
> +			break;
> +
> +		case NAND_OP_DATA_OUT_INSTR:
> +			size = nand_subop_get_data_len(subop, op_id);
> +			offset = nand_subop_get_data_start_off(subop, op_id);
> +
> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> +				COMMAND_TX | COMMAND_A_VALID;
> +
> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
> +			writel_relaxed(reg, ctrl->regs + RESP);
> +
> +			break;
> +		case NAND_OP_WAITRDY_INSTR:
> +			cmd |= COMMAND_RBSY_CHK;
> +			break;
> +
> +		}
> +	}
> +
> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> +					     msecs_to_jiffies(500));

It's not obvious to me whether _io_ variant is appropriate to use here, would 
be nice if somebody could clarify that. Maybe block/ already does the IO 
accounting itself and hence the IO time would be counted twice in that case.



^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-11 23:32   ` Dmitry Osipenko
@ 2018-06-12  8:02     ` Stefan Agner
  2018-06-12  8:13       ` Boris Brezillon
  0 siblings, 1 reply; 24+ messages in thread
From: Stefan Agner @ 2018-06-12  8:02 UTC (permalink / raw)
  To: Dmitry Osipenko
  Cc: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On 12.06.2018 01:32, Dmitry Osipenko wrote:
> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>> Add support for the NAND flash controller found on NVIDIA
>> Tegra 2 SoCs. This implementation does not make use of the
>> command queue feature. Regular operations/data transfers are
>> done in PIO mode. Page read/writes with hardware ECC make
>> use of the DMA for data transfer.
> 
> Are "regular operations/data transfers" == "raw read/writes"? Seems you've 
> fixed DMA now and hence should adjust the commit message if that's the case.
> 

Yep, will fix this!

>>
>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
> 
> Otherwise looks good to me:
> 
> Reviewed-by: Dmitry Osipenko <digetx@gmail.com>

Thanks for you review!

> 
> 
> There couple nit comments about newlines below, maybe you could clean up them 
> if there will be another revision.

Ok, will take care of them as well.

--
Stefan

> 
>>  MAINTAINERS                       |    7 +
>>  drivers/mtd/nand/raw/Kconfig      |    6 +
>>  drivers/mtd/nand/raw/Makefile     |    1 +
>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>>  4 files changed, 1262 insertions(+)
>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 58b9861ccf99..c2e5571c85d4 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -13844,6 +13844,13 @@ M:	Laxman Dewangan <ldewangan@nvidia.com>
>>  S:	Supported
>>  F:	drivers/input/keyboard/tegra-kbc.c
>>
>> +TEGRA NAND DRIVER
>> +M:	Stefan Agner <stefan@agner.ch>
>> +M:	Lucas Stach <dev@lynxeye.de>
>> +S:	Maintained
>> +F:	Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
>> +F:	drivers/mtd/nand/raw/tegra_nand.c
>> +
>>  TEGRA PWM DRIVER
>>  M:	Thierry Reding <thierry.reding@gmail.com>
>>  S:	Supported
>> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
>> index 19a2b283fbbe..e9093f52371e 100644
>> --- a/drivers/mtd/nand/raw/Kconfig
>> +++ b/drivers/mtd/nand/raw/Kconfig
>> @@ -534,4 +534,10 @@ config MTD_NAND_MTK
>>  	  Enables support for NAND controller on MTK SoCs.
>>  	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
>>
>> +config MTD_NAND_TEGRA
>> +	tristate "Support for NAND controller on NVIDIA Tegra"
>> +	depends on ARCH_TEGRA || COMPILE_TEST
>> +	help
>> +	  Enables support for NAND flash controller on NVIDIA Tegra SoC.
>> +
>>  endif # MTD_NAND
>> diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
>> index 165b7ef9e9a1..d5a5f9832b88 100644
>> --- a/drivers/mtd/nand/raw/Makefile
>> +++ b/drivers/mtd/nand/raw/Makefile
>> @@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504)	        +=
> hisi504_nand.o
>>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
>>  obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
>>  obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
>> +obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
>>
>>  nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
>>  nand-objs += nand_amd.o
>> diff --git a/drivers/mtd/nand/raw/tegra_nand.c
>> b/drivers/mtd/nand/raw/tegra_nand.c new file mode 100644
>> index 000000000000..dd23a5eb6af3
>> --- /dev/null
>> +++ b/drivers/mtd/nand/raw/tegra_nand.c
>> @@ -0,0 +1,1248 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2018 Stefan Agner <stefan@agner.ch>
>> + * Copyright (C) 2014-2015 Lucas Stach <dev@lynxeye.de>
>> + * Copyright (C) 2012 Avionic Design GmbH
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/completion.h>
>> +#include <linux/delay.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/err.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/mtd/partitions.h>
>> +#include <linux/mtd/rawnand.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/reset.h>
>> +
>> +#define COMMAND					0x00
>> +#define   COMMAND_GO				BIT(31)
>> +#define   COMMAND_CLE				BIT(30)
>> +#define   COMMAND_ALE				BIT(29)
>> +#define   COMMAND_PIO				BIT(28)
>> +#define   COMMAND_TX				BIT(27)
>> +#define   COMMAND_RX				BIT(26)
>> +#define   COMMAND_SEC_CMD			BIT(25)
>> +#define   COMMAND_AFT_DAT			BIT(24)
>> +#define   COMMAND_TRANS_SIZE(x)			(((x - 1) & 0xf) << 20)
>> +#define   COMMAND_A_VALID			BIT(19)
>> +#define   COMMAND_B_VALID			BIT(18)
>> +#define   COMMAND_RD_STATUS_CHK			BIT(17)
>> +#define   COMMAND_RBSY_CHK			BIT(16)
>> +#define   COMMAND_CE(x)				BIT(8 + ((x) & 0x7))
>> +#define   COMMAND_CLE_SIZE(x)			(((x - 1) & 0x3) << 4)
>> +#define   COMMAND_ALE_SIZE(x)			(((x - 1) & 0xf) << 0)
>> +
>> +#define STATUS					0x04
>> +
>> +#define ISR					0x08
>> +#define   ISR_CORRFAIL_ERR			BIT(24)
>> +#define   ISR_UND				BIT(7)
>> +#define   ISR_OVR				BIT(6)
>> +#define   ISR_CMD_DONE				BIT(5)
>> +#define   ISR_ECC_ERR				BIT(4)
>> +
>> +#define IER					0x0c
>> +#define   IER_ERR_TRIG_VAL(x)			(((x) & 0xf) << 16)
>> +#define   IER_UND				BIT(7)
>> +#define   IER_OVR				BIT(6)
>> +#define   IER_CMD_DONE				BIT(5)
>> +#define   IER_ECC_ERR				BIT(4)
>> +#define   IER_GIE				BIT(0)
>> +
>> +#define CONFIG					0x10
>> +#define   CONFIG_HW_ECC				BIT(31)
>> +#define   CONFIG_ECC_SEL			BIT(30)
>> +#define   CONFIG_ERR_COR			BIT(29)
>> +#define   CONFIG_PIPE_EN			BIT(28)
>> +#define   CONFIG_TVAL_4				(0 << 24)
>> +#define   CONFIG_TVAL_6				(1 << 24)
>> +#define   CONFIG_TVAL_8				(2 << 24)
>> +#define   CONFIG_SKIP_SPARE			BIT(23)
>> +#define   CONFIG_BUS_WIDTH_16			BIT(21)
>> +#define   CONFIG_COM_BSY			BIT(20)
>> +#define   CONFIG_PS_256				(0 << 16)
>> +#define   CONFIG_PS_512				(1 << 16)
>> +#define   CONFIG_PS_1024			(2 << 16)
>> +#define   CONFIG_PS_2048			(3 << 16)
>> +#define   CONFIG_PS_4096			(4 << 16)
>> +#define   CONFIG_SKIP_SPARE_SIZE_4		(0 << 14)
>> +#define   CONFIG_SKIP_SPARE_SIZE_8		(1 << 14)
>> +#define   CONFIG_SKIP_SPARE_SIZE_12		(2 << 14)
>> +#define   CONFIG_SKIP_SPARE_SIZE_16		(3 << 14)
>> +#define   CONFIG_TAG_BYTE_SIZE(x)			((x) & 0xff)
>> +
>> +#define TIMING_1				0x14
>> +#define   TIMING_TRP_RESP(x)			(((x) & 0xf) << 28)
>> +#define   TIMING_TWB(x)				(((x) & 0xf) << 24)
>> +#define   TIMING_TCR_TAR_TRR(x)			(((x) & 0xf) << 20)
>> +#define   TIMING_TWHR(x)			(((x) & 0xf) << 16)
>> +#define   TIMING_TCS(x)				(((x) & 0x3) << 14)
>> +#define   TIMING_TWH(x)				(((x) & 0x3) << 12)
>> +#define   TIMING_TWP(x)				(((x) & 0xf) <<  8)
>> +#define   TIMING_TRH(x)				(((x) & 0x3) <<  4)
>> +#define   TIMING_TRP(x)				(((x) & 0xf) <<  0)
>> +
>> +#define RESP					0x18
>> +
>> +#define TIMING_2				0x1c
>> +#define   TIMING_TADL(x)			((x) & 0xf)
>> +
>> +#define CMD_REG1				0x20
>> +#define CMD_REG2				0x24
>> +#define ADDR_REG1				0x28
>> +#define ADDR_REG2				0x2c
>> +
>> +#define DMA_MST_CTRL				0x30
>> +#define   DMA_MST_CTRL_GO			BIT(31)
>> +#define   DMA_MST_CTRL_IN			(0 << 30)
>> +#define   DMA_MST_CTRL_OUT			BIT(30)
>> +#define   DMA_MST_CTRL_PERF_EN			BIT(29)
>> +#define   DMA_MST_CTRL_IE_DONE			BIT(28)
>> +#define   DMA_MST_CTRL_REUSE			BIT(27)
>> +#define   DMA_MST_CTRL_BURST_1			(2 << 24)
>> +#define   DMA_MST_CTRL_BURST_4			(3 << 24)
>> +#define   DMA_MST_CTRL_BURST_8			(4 << 24)
>> +#define   DMA_MST_CTRL_BURST_16			(5 << 24)
>> +#define   DMA_MST_CTRL_IS_DONE			BIT(20)
>> +#define   DMA_MST_CTRL_EN_A			BIT(2)
>> +#define   DMA_MST_CTRL_EN_B			BIT(1)
>> +
>> +#define DMA_CFG_A				0x34
>> +#define DMA_CFG_B				0x38
>> +
>> +#define FIFO_CTRL				0x3c
>> +#define   FIFO_CTRL_CLR_ALL			BIT(3)
>> +
>> +#define DATA_PTR				0x40
>> +#define TAG_PTR					0x44
>> +#define ECC_PTR					0x48
>> +
>> +#define DEC_STATUS				0x4c
>> +#define   DEC_STATUS_A_ECC_FAIL			BIT(1)
>> +#define   DEC_STATUS_ERR_COUNT_MASK		0x00ff0000
>> +#define   DEC_STATUS_ERR_COUNT_SHIFT		16
>> +
>> +#define HWSTATUS_CMD				0x50
>> +#define HWSTATUS_MASK				0x54
>> +#define   HWSTATUS_RDSTATUS_MASK(x)		(((x) & 0xff) << 24)
>> +#define   HWSTATUS_RDSTATUS_VALUE(x)		(((x) & 0xff) << 16)
>> +#define   HWSTATUS_RBSY_MASK(x)			(((x) & 0xff) << 8)
>> +#define   HWSTATUS_RBSY_VALUE(x)		(((x) & 0xff) << 0)
>> +
>> +#define BCH_CONFIG				0xcc
>> +#define   BCH_ENABLE				BIT(0)
>> +#define   BCH_TVAL_4				(0 << 4)
>> +#define   BCH_TVAL_8				(1 << 4)
>> +#define   BCH_TVAL_14				(2 << 4)
>> +#define   BCH_TVAL_16				(3 << 4)
>> +
>> +#define DEC_STAT_RESULT				0xd0
>> +#define DEC_STAT_BUF				0xd4
>> +#define   DEC_STAT_BUF_FAIL_SEC_FLAG_MASK	0xff000000
>> +#define   DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT	24
>> +#define   DEC_STAT_BUF_CORR_SEC_FLAG_MASK	0x00ff0000
>> +#define   DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT	16
>> +#define   DEC_STAT_BUF_MAX_CORR_CNT_MASK	0x00001f00
>> +#define   DEC_STAT_BUF_MAX_CORR_CNT_SHIFT	8
>> +
>> +#define OFFSET(val, off)	((val) < (off) ? 0 : (val) - (off))
>> +
>> +#define SKIP_SPARE_BYTES	4
>> +#define BITS_PER_STEP_RS	18
>> +#define BITS_PER_STEP_BCH	13
>> +
>> +#define INT_MASK		(IER_UND | IER_OVR | IER_CMD_DONE | IER_GIE)
>> +#define HWSTATUS_CMD_DEFAULT	NAND_STATUS_READY
>> +#define HWSTATUS_MASK_DEFAULT	(HWSTATUS_RDSTATUS_MASK(1) | \
>> +				HWSTATUS_RDSTATUS_VALUE(0) | \
>> +				HWSTATUS_RBSY_MASK(NAND_STATUS_READY) | \
>> +				HWSTATUS_RBSY_VALUE(NAND_STATUS_READY))
>> +
>> +struct tegra_nand_controller {
>> +	struct nand_hw_control controller;
>> +	struct device *dev;
>> +	void __iomem *regs;
>> +	int irq;
>> +	struct clk *clk;
>> +	struct completion command_complete;
>> +	struct completion dma_complete;
>> +	bool last_read_error;
>> +	int cur_cs;
>> +	struct nand_chip *chip;
>> +};
>> +
>> +struct tegra_nand_chip {
>> +	struct nand_chip chip;
>> +	struct gpio_desc *wp_gpio;
>> +	struct mtd_oob_region tag;
>> +	u32 config;
>> +	u32 config_ecc;
>> +	u32 bch_config;
>> +	int cs[1];
>> +};
>> +
>> +static inline struct tegra_nand_controller *to_tegra_ctrl(
>> +						struct nand_hw_control *hw_ctrl)
>> +{
>> +	return container_of(hw_ctrl, struct tegra_nand_controller, controller);
>> +}
>> +
>> +static inline struct tegra_nand_chip *to_tegra_chip(struct nand_chip *chip)
>> +{
>> +	return container_of(chip, struct tegra_nand_chip, chip);
>> +}
>> +
>> +static int tegra_nand_ooblayout_rs_ecc(struct mtd_info *mtd, int section,
>> +				       struct mtd_oob_region *oobregion)
>> +{
>> +	struct nand_chip *chip = mtd_to_nand(mtd);
>> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
>> +					  BITS_PER_BYTE);
>> +
>> +	if (section > 0)
>> +		return -ERANGE;
>> +
>> +	oobregion->offset = SKIP_SPARE_BYTES;
>> +	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
>> +
>> +	return 0;
>> +}
>> +
>> +static int tegra_nand_ooblayout_rs_free(struct mtd_info *mtd, int section,
>> +					struct mtd_oob_region *oobregion)
>> +{
>> +	struct nand_chip *chip = mtd_to_nand(mtd);
>> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength,
>> +					  BITS_PER_BYTE);
>> +
>> +	if (section > 0)
>> +		return -ERANGE;
>> +
>> +	oobregion->offset = SKIP_SPARE_BYTES +
>> +			    round_up(bytes_per_step * chip->ecc.steps, 4);
>> +	oobregion->length = mtd->oobsize - oobregion->offset;
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct mtd_ooblayout_ops tegra_nand_oob_rs_ops = {
>> +	.ecc = tegra_nand_ooblayout_rs_ecc,
>> +	.free = tegra_nand_ooblayout_rs_free,
>> +};
>> +
>> +static int tegra_nand_ooblayout_bch_ecc(struct mtd_info *mtd, int section,
>> +				       struct mtd_oob_region *oobregion)
>> +{
>> +	struct nand_chip *chip = mtd_to_nand(mtd);
>> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
>> +					  BITS_PER_BYTE);
>> +
>> +	if (section > 0)
>> +		return -ERANGE;
>> +
>> +	oobregion->offset = SKIP_SPARE_BYTES;
>> +	oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4);
>> +
>> +	return 0;
>> +}
>> +
>> +static int tegra_nand_ooblayout_bch_free(struct mtd_info *mtd, int section,
>> +					struct mtd_oob_region *oobregion)
>> +{
>> +	struct nand_chip *chip = mtd_to_nand(mtd);
>> +	int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength,
>> +					  BITS_PER_BYTE);
>> +
>> +	if (section > 0)
>> +		return -ERANGE;
>> +
>> +	oobregion->offset = SKIP_SPARE_BYTES +
>> +			    round_up(bytes_per_step * chip->ecc.steps, 4);
>> +	oobregion->length = mtd->oobsize - oobregion->offset;
>> +
>> +	return 0;
>> +}
>> +
>> +/*
>> + * Layout with tag bytes is
>> + *
>> + *
>> --------------------------------------------------------------------------
>> + * | main area                       | skip bytes | tag bytes | parity |
>> .. | + *
>> --------------------------------------------------------------------------
>> + *
>> + * If not tag bytes are written, parity moves right after skip bytes!
>> + */
>> +static const struct mtd_ooblayout_ops tegra_nand_oob_bch_ops = {
>> +	.ecc = tegra_nand_ooblayout_bch_ecc,
>> +	.free = tegra_nand_ooblayout_bch_free,
>> +};
>> +
>> +static irqreturn_t tegra_nand_irq(int irq, void *data)
>> +{
>> +	struct tegra_nand_controller *ctrl = data;
>> +	u32 isr, dma;
>> +
>> +	isr = readl_relaxed(ctrl->regs + ISR);
>> +	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
>> +	dev_dbg(ctrl->dev, "isr %08x\n", isr);
>> +
>> +	if (!isr && !(dma & DMA_MST_CTRL_IS_DONE))
>> +		return IRQ_NONE;
>> +
>> +	/*
>> +	 * The bit name is somewhat missleading: This is also set when
>> +	 * HW ECC was successful. The data sheet states:
>> +	 * Correctable OR Un-correctable errors occurred in the DMA transfer...
>> +	 */
>> +	if (isr & ISR_CORRFAIL_ERR)
>> +		ctrl->last_read_error = true;
>> +
>> +	if (isr & ISR_CMD_DONE)
>> +		complete(&ctrl->command_complete);
>> +
>> +	if (isr & ISR_UND)
>> +		dev_err(ctrl->dev, "FIFO underrun\n");
>> +
>> +	if (isr & ISR_OVR)
>> +		dev_err(ctrl->dev, "FIFO overrun\n");
>> +
>> +	/* handle DMA interrupts */
>> +	if (dma & DMA_MST_CTRL_IS_DONE) {
>> +		writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
>> +		complete(&ctrl->dma_complete);
>> +	}
>> +
>> +	/* clear interrupts */
>> +	writel_relaxed(isr, ctrl->regs + ISR);
>> +
>> +	return IRQ_HANDLED;
>> +}
>> +
>> +static const char * const tegra_nand_reg_names[] = {
>> +	"COMMAND",
>> +	"STATUS",
>> +	"ISR",
>> +	"IER",
>> +	"CONFIG",
>> +	"TIMING",
>> +	NULL,
>> +	"TIMING2",
>> +	"CMD_REG1",
>> +	"CMD_REG2",
>> +	"ADDR_REG1",
>> +	"ADDR_REG2",
>> +	"DMA_MST_CTRL",
>> +	"DMA_CFG_A",
>> +	"DMA_CFG_B",
>> +	"FIFO_CTRL",
>> +};
>> +
>> +static void tegra_nand_dump_reg(struct tegra_nand_controller *ctrl)
>> +{
>> +	u32 reg;
>> +	int i;
>> +
>> +	dev_err(ctrl->dev, "Tegra NAND controller register dump\n");
>> +	for (i = 0; i < ARRAY_SIZE(tegra_nand_reg_names); i++) {
>> +		const char *reg_name = tegra_nand_reg_names[i];
>> +
>> +		if (!reg_name)
>> +			continue;
>> +
>> +		reg = readl_relaxed(ctrl->regs + (i * 4));
>> +		dev_err(ctrl->dev, "%s: 0x%08x\n", reg_name, reg);
>> +	}
>> +}
>> +
>> +static void tegra_nand_controller_abort(struct tegra_nand_controller *ctrl)
>> +{
>> +	u32 isr, dma;
>> +
>> +	disable_irq(ctrl->irq);
>> +
>> +	/* Abort current command/DMA operation */
>> +	writel_relaxed(0, ctrl->regs + DMA_MST_CTRL);
>> +	writel_relaxed(0, ctrl->regs + COMMAND);
>> +
>> +	/* clear interrupts */
>> +	isr = readl_relaxed(ctrl->regs + ISR);
>> +	writel_relaxed(isr, ctrl->regs + ISR);
>> +	dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL);
>> +	writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL);
>> +
>> +	reinit_completion(&ctrl->command_complete);
>> +	reinit_completion(&ctrl->dma_complete);
>> +
>> +	enable_irq(ctrl->irq);
>> +}
>> +
>> +static int tegra_nand_cmd(struct nand_chip *chip,
>> +			 const struct nand_subop *subop)
>> +{
>> +	const struct nand_op_instr *instr;
>> +	const struct nand_op_instr *instr_data_in = NULL;
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +	unsigned int op_id, size = 0, offset = 0;
>> +	bool first_cmd = true;
>> +	u32 reg, cmd = 0;
>> +	int ret;
>> +
>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>> +		unsigned int naddrs, i;
>> +		const u8 *addrs;
>> +		u32 addr1 = 0, addr2 = 0;
>> +
>> +		instr = &subop->instrs[op_id];
>> +
>> +		switch (instr->type) {
>> +		case NAND_OP_CMD_INSTR:
>> +			if (first_cmd) {
>> +				cmd |= COMMAND_CLE;
>> +				writel_relaxed(instr->ctx.cmd.opcode,
>> +					       ctrl->regs + CMD_REG1);
>> +			} else {
>> +				cmd |= COMMAND_SEC_CMD;
>> +				writel_relaxed(instr->ctx.cmd.opcode,
>> +					       ctrl->regs + CMD_REG2);
>> +			}
>> +			first_cmd = false;
>> +			break;
> 
> Newline here.
> 
>> +		case NAND_OP_ADDR_INSTR:
>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>> +			addrs = &instr->ctx.addr.addrs[offset];
>> +
>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>> +			naddrs -= i;
>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>> +			break;
>> +
>> +		case NAND_OP_DATA_IN_INSTR:
>> +			size = nand_subop_get_data_len(subop, op_id);
>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>> +
>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> +				COMMAND_RX | COMMAND_A_VALID;
>> +
>> +			instr_data_in = instr;
>> +			break;
>> +
>> +		case NAND_OP_DATA_OUT_INSTR:
>> +			size = nand_subop_get_data_len(subop, op_id);
>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>> +
>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> +				COMMAND_TX | COMMAND_A_VALID;
>> +
>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
>> +			writel_relaxed(reg, ctrl->regs + RESP);
>> +
>> +			break;
> 
> Newline here.
> 
>> +		case NAND_OP_WAITRDY_INSTR:
>> +			cmd |= COMMAND_RBSY_CHK;
>> +			break;
>> +
> 
> Blank line isn't needed here.
> 
>> +		}
>> +	}
>> +
>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>> +					     msecs_to_jiffies(500));
>> +	if (!ret) {
>> +		dev_err(ctrl->dev, "COMMAND timeout\n");
>> +		tegra_nand_dump_reg(ctrl);
>> +		tegra_nand_controller_abort(ctrl);
>> +		return -ETIMEDOUT;
>> +	}
>> +
>> +	if (instr_data_in) {
>> +		reg = readl_relaxed(ctrl->regs + RESP);
>> +		memcpy(instr_data_in->ctx.data.buf.in + offset, &reg, size);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct nand_op_parser tegra_nand_op_parser = NAND_OP_PARSER(
>> +	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
>> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
>> +		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8),
>> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
>> +		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
>> +	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
>> +		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, 4)),
>> +	NAND_OP_PARSER_PATTERN(tegra_nand_cmd,
>> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
>> +		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8),
>> +		NAND_OP_PARSER_PAT_CMD_ELEM(true),
>> +		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
>> +		NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, 4)),
>> +	);
>> +
>> +static int tegra_nand_exec_op(struct nand_chip *chip,
>> +			     const struct nand_operation *op,
>> +			     bool check_only)
>> +{
>> +	return nand_op_parser_exec_op(chip, &tegra_nand_op_parser, op,
>> +				      check_only);
>> +}
> 
> Newline here.
> 
>> +static void tegra_nand_select_chip(struct mtd_info *mtd, int die_nr)
>> +{
>> +	struct nand_chip *chip = mtd_to_nand(mtd);
>> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +
>> +	if (die_nr < 0 || die_nr > 1) {
>> +		ctrl->cur_cs = -1;
>> +		return;
>> +	}
>> +
>> +	ctrl->cur_cs = nand->cs[die_nr];
>> +}
>> +
>> +static void tegra_nand_hw_ecc(struct tegra_nand_controller *ctrl,
>> +			      struct nand_chip *chip, bool enable)
>> +{
>> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
>> +
>> +	if (chip->ecc.algo == NAND_ECC_BCH && enable)
>> +		writel_relaxed(nand->bch_config, ctrl->regs + BCH_CONFIG);
>> +	else
>> +		writel_relaxed(0, ctrl->regs + BCH_CONFIG);
>> +
>> +	if (enable)
>> +		writel_relaxed(nand->config_ecc, ctrl->regs + CONFIG);
>> +	else
>> +		writel_relaxed(nand->config, ctrl->regs + CONFIG);
>> +}
>> +
>> +static int tegra_nand_page_xfer(struct mtd_info *mtd, struct nand_chip
>> *chip, +				void *buf, void *oob_buf, int oob_len, int page,
>> +				bool read)
>> +{
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +	enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
>> +	dma_addr_t dma_addr = 0, dma_addr_oob = 0;
>> +	u32 addr1, cmd, dma_ctrl;
>> +	int ret;
>> +
>> +	if (read) {
>> +		writel_relaxed(NAND_CMD_READ0, ctrl->regs + CMD_REG1);
>> +		writel_relaxed(NAND_CMD_READSTART, ctrl->regs + CMD_REG2);
>> +	} else {
>> +		writel_relaxed(NAND_CMD_SEQIN, ctrl->regs + CMD_REG1);
>> +		writel_relaxed(NAND_CMD_PAGEPROG, ctrl->regs + CMD_REG2);
>> +	}
>> +	cmd = COMMAND_CLE | COMMAND_SEC_CMD;
>> +
>> +	/* Lower 16-bits are column, by default 0 */
>> +	addr1 = page << 16;
>> +
>> +	if (!buf)
>> +		addr1 |= mtd->writesize;
>> +	writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>> +
>> +	if (chip->options & NAND_ROW_ADDR_3) {
>> +		writel_relaxed(page >> 16, ctrl->regs + ADDR_REG2);
>> +		cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(5);
>> +	} else {
>> +		cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(4);
>> +	}
>> +
>> +	if (buf) {
>> +		dma_addr = dma_map_single(ctrl->dev, buf, mtd->writesize, dir);
>> +		ret = dma_mapping_error(ctrl->dev, dma_addr);
>> +		if (ret) {
>> +			dev_err(ctrl->dev, "dma mapping error\n");
>> +			return -EINVAL;
>> +		}
>> +
>> +		writel_relaxed(mtd->writesize - 1, ctrl->regs + DMA_CFG_A);
>> +		writel_relaxed(dma_addr, ctrl->regs + DATA_PTR);
>> +	}
>> +
>> +	if (oob_buf) {
>> +		dma_addr_oob = dma_map_single(ctrl->dev, oob_buf, mtd->oobsize,
>> +					      dir);
>> +		ret = dma_mapping_error(ctrl->dev, dma_addr_oob);
>> +		if (ret) {
>> +			dev_err(ctrl->dev, "dma mapping error\n");
>> +			ret = -EINVAL;
>> +			goto err_unmap_dma_page;
>> +		}
>> +
>> +		writel_relaxed(oob_len - 1, ctrl->regs + DMA_CFG_B);
>> +		writel_relaxed(dma_addr_oob, ctrl->regs + TAG_PTR);
>> +	}
>> +
>> +	dma_ctrl = DMA_MST_CTRL_GO | DMA_MST_CTRL_PERF_EN |
>> +		   DMA_MST_CTRL_IE_DONE | DMA_MST_CTRL_IS_DONE |
>> +		   DMA_MST_CTRL_BURST_16;
>> +
>> +	if (buf)
>> +		dma_ctrl |= DMA_MST_CTRL_EN_A;
>> +	if (oob_buf)
>> +		dma_ctrl |= DMA_MST_CTRL_EN_B;
>> +
>> +	if (read)
>> +		dma_ctrl |= DMA_MST_CTRL_IN | DMA_MST_CTRL_REUSE;
>> +	else
>> +		dma_ctrl |= DMA_MST_CTRL_OUT;
>> +
>> +	writel_relaxed(dma_ctrl, ctrl->regs + DMA_MST_CTRL);
>> +
>> +	cmd |= COMMAND_GO | COMMAND_RBSY_CHK | COMMAND_TRANS_SIZE(9) |
>> +	       COMMAND_CE(ctrl->cur_cs);
>> +
>> +	if (buf)
>> +		cmd |= COMMAND_A_VALID;
>> +	if (oob_buf)
>> +		cmd |= COMMAND_B_VALID;
>> +
>> +	if (read)
>> +		cmd |= COMMAND_RX;
>> +	else
>> +		cmd |= COMMAND_TX | COMMAND_AFT_DAT;
>> +
>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>> +
>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>> +					     msecs_to_jiffies(500));
>> +	if (!ret) {
>> +		dev_err(ctrl->dev, "COMMAND timeout\n");
>> +		tegra_nand_dump_reg(ctrl);
>> +		tegra_nand_controller_abort(ctrl);
>> +		ret = -ETIMEDOUT;
>> +		goto err_unmap_dma;
>> +	}
>> +
>> +	ret = wait_for_completion_io_timeout(&ctrl->dma_complete,
>> +					     msecs_to_jiffies(500));
>> +	if (!ret) {
>> +		dev_err(ctrl->dev, "DMA timeout\n");
>> +		tegra_nand_dump_reg(ctrl);
>> +		tegra_nand_controller_abort(ctrl);
>> +		ret = -ETIMEDOUT;
>> +		goto err_unmap_dma;
>> +	}
>> +	ret = 0;
>> +
>> +err_unmap_dma:
>> +	if (oob_buf)
>> +		dma_unmap_single(ctrl->dev, dma_addr_oob, mtd->oobsize, dir);
>> +err_unmap_dma_page:
>> +	if (buf)
>> +		dma_unmap_single(ctrl->dev, dma_addr, mtd->writesize, dir);
>> +
>> +	return ret;
>> +}
>> +
>> +static int tegra_nand_read_page_raw(struct mtd_info *mtd,
>> +				    struct nand_chip *chip,
>> +				    uint8_t *buf, int oob_required, int page)
>> +{
>> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
>> +
>> +	return tegra_nand_page_xfer(mtd, chip, buf, oob_buf,
>> +				    mtd->oobsize, page, true);
>> +}
>> +
>> +static int tegra_nand_write_page_raw(struct mtd_info *mtd,
>> +				     struct nand_chip *chip,
>> +				     const uint8_t *buf, int oob_required,
>> +				     int page)
>> +{
>> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
>> +
>> +	return tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf,
>> +				     mtd->oobsize, page, false);
>> +}
>> +
>> +static int tegra_nand_read_oob(struct mtd_info *mtd, struct nand_chip
>> *chip, +			       int page)
>> +{
>> +	return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi,
>> +				    mtd->oobsize, page, true);
>> +}
>> +
>> +static int tegra_nand_write_oob(struct mtd_info *mtd, struct nand_chip
>> *chip, +				int page)
>> +{
>> +	return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi,
>> +				    mtd->oobsize, page, false);
>> +}
>> +
>> +static int tegra_nand_read_page_hwecc(struct mtd_info *mtd,
>> +				      struct nand_chip *chip,
>> +				      uint8_t *buf, int oob_required, int page)
>> +{
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
>> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
>> +	u32 dec_stat, max_corr_cnt;
>> +	unsigned long fail_sec_flag;
>> +	int ret;
>> +
>> +	tegra_nand_hw_ecc(ctrl, chip, true);
>> +	ret = tegra_nand_page_xfer(mtd, chip, buf, oob_buf, nand->tag.length,
>> +				   page, true);
>> +	tegra_nand_hw_ecc(ctrl, chip, false);
>> +	if (ret)
>> +		return ret;
>> +
>> +	/* No correctable or un-correctable errors, page must have 0 bitflips */
>> +	if (!ctrl->last_read_error)
>> +		return 0;
>> +
>> +	/*
>> +	 * Correctable or un-correctable errors occurred. Use DEC_STAT_BUF
>> +	 * which contains information for all ECC selections.
>> +	 *
>> +	 * Note that since we do not use Command Queues DEC_RESULT does not
>> +	 * state the number of pages we can read from the DEC_STAT_BUF. But
>> +	 * since CORRFAIL_ERR did occur during page read we do have a valid
>> +	 * result in DEC_STAT_BUF.
>> +	 */
>> +	ctrl->last_read_error = false;
>> +	dec_stat = readl_relaxed(ctrl->regs + DEC_STAT_BUF);
>> +
>> +	fail_sec_flag = (dec_stat & DEC_STAT_BUF_FAIL_SEC_FLAG_MASK) >>
>> +			DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT;
>> +
>> +	max_corr_cnt = (dec_stat & DEC_STAT_BUF_MAX_CORR_CNT_MASK) >>
>> +		       DEC_STAT_BUF_MAX_CORR_CNT_SHIFT;
>> +
>> +	if (fail_sec_flag) {
>> +		int bit, max_bitflips = 0;
>> +
>> +		/*
>> +		 * Check if all sectors in a page failed. If only some failed
>> +		 * its definitly not an erased page and we can return error
>> +		 * stats right away.
>> +		 *
>> +		 * E.g. controller might return fail_sec_flag with 0x4, which
>> +		 * would mean only the third sector failed to correct.
>> +		 */
>> +		if (fail_sec_flag ^ GENMASK(chip->ecc.steps - 1, 0)) {
>> +			mtd->ecc_stats.failed += hweight8(fail_sec_flag);
>> +			return max_corr_cnt;
>> +		}
>> +
>> +		/*
>> +		 * All sectors failed to correct, but the ECC isn't smart
>> +		 * enough to figure out if a page is really completely erased.
>> +		 * We check the read data here to figure out if it's a
>> +		 * legitimate ECC error or only an erased page.
>> +		 */
>> +		for_each_set_bit(bit, &fail_sec_flag, chip->ecc.steps) {
>> +			u8 *data = buf + (chip->ecc.size * bit);
>> +
>> +			ret = nand_check_erased_ecc_chunk(data, chip->ecc.size,
>> +							  NULL, 0,
>> +							  NULL, 0,
>> +							  chip->ecc.strength);
>> +			if (ret < 0)
>> +				mtd->ecc_stats.failed++;
>> +			else
>> +				max_bitflips = max(ret, max_bitflips);
>> +		}
>> +
>> +		return max_t(unsigned int, max_corr_cnt, max_bitflips);
>> +	} else {
>> +		int corr_sec_flag;
>> +
>> +		corr_sec_flag = (dec_stat & DEC_STAT_BUF_CORR_SEC_FLAG_MASK) >>
>> +				DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT;
>> +
>> +		/*
>> +		 * The value returned in the register is the maximum of
>> +		 * bitflips encountered in any of the ECC regions. As there is
>> +		 * no way to get the number of bitflips in a specific regions
>> +		 * we are not able to deliver correct stats but instead
>> +		 * overestimate the number of corrected bitflips by assuming
>> +		 * that all regions where errors have been corrected
>> +		 * encountered the maximum number of bitflips.
>> +		 */
>> +		mtd->ecc_stats.corrected += max_corr_cnt * hweight8(corr_sec_flag);
>> +
>> +		return max_corr_cnt;
>> +	}
>> +
> 
> Blank line isn't needed here.
> 
>> +}
>> +
>> +static int tegra_nand_write_page_hwecc(struct mtd_info *mtd,
>> +				       struct nand_chip *chip,
>> +				       const uint8_t *buf, int oob_required,
>> +				       int page)
>> +{
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
>> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
>> +	int ret;
>> +
>> +	tegra_nand_hw_ecc(ctrl, chip, true);
>> +	ret = tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf,
>> +				   nand->tag.length, page, false);
>> +	tegra_nand_hw_ecc(ctrl, chip, false);
>> +
>> +	return ret;
>> +}
>> +
>> +static void tegra_nand_setup_timing(struct tegra_nand_controller *ctrl,
>> +				    const struct nand_sdr_timings *timings)
>> +{
>> +	/*
>> +	 * The period (and all other timings in this function) is in ps,
>> +	 * so need to take care here to avoid integer overflows.
>> +	 */
>> +	unsigned int rate = clk_get_rate(ctrl->clk) / 1000000;
>> +	unsigned int period = DIV_ROUND_UP(1000000, rate);
>> +	u32 val, reg = 0;
>> +
>> +	val = DIV_ROUND_UP(max3(timings->tAR_min, timings->tRR_min,
>> +				timings->tRC_min), period);
>> +	reg |= TIMING_TCR_TAR_TRR(OFFSET(val, 3));
>> +
>> +	val = DIV_ROUND_UP(max(max(timings->tCS_min, timings->tCH_min),
>> +			       max(timings->tALS_min, timings->tALH_min)),
>> +			   period);
>> +	reg |= TIMING_TCS(OFFSET(val, 2));
>> +
>> +	val = DIV_ROUND_UP(max(timings->tRP_min, timings->tREA_max) + 6000,
>> +			   period);
>> +	reg |= TIMING_TRP(OFFSET(val, 1)) | TIMING_TRP_RESP(OFFSET(val, 1));
>> +
>> +	reg |= TIMING_TWB(OFFSET(DIV_ROUND_UP(timings->tWB_max, period), 1));
>> +	reg |= TIMING_TWHR(OFFSET(DIV_ROUND_UP(timings->tWHR_min, period), 1));
>> +	reg |= TIMING_TWH(OFFSET(DIV_ROUND_UP(timings->tWH_min, period), 1));
>> +	reg |= TIMING_TWP(OFFSET(DIV_ROUND_UP(timings->tWP_min, period), 1));
>> +	reg |= TIMING_TRH(OFFSET(DIV_ROUND_UP(timings->tREH_min, period), 1));
>> +
>> +	writel_relaxed(reg, ctrl->regs + TIMING_1);
>> +
>> +	val = DIV_ROUND_UP(timings->tADL_min, period);
>> +	reg = TIMING_TADL(OFFSET(val, 3));
>> +
>> +	writel_relaxed(reg, ctrl->regs + TIMING_2);
>> +}
>> +
>> +static int tegra_nand_setup_data_interface(struct mtd_info *mtd, int
>> csline, +					const struct nand_data_interface *conf)
>> +{
>> +	struct nand_chip *chip = mtd_to_nand(mtd);
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +	const struct nand_sdr_timings *timings;
>> +
>> +	timings = nand_get_sdr_timings(conf);
>> +	if (IS_ERR(timings))
>> +		return PTR_ERR(timings);
>> +
>> +	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
>> +		return 0;
>> +
>> +	tegra_nand_setup_timing(ctrl, timings);
>> +
>> +	return 0;
>> +}
>> +
>> +static const int rs_strength_bootable[] = { 4 };
>> +static const int rs_strength[] = { 4, 6, 8 };
>> +static const int bch_strength_bootable[] = { 8, 16 };
>> +static const int bch_strength[] = { 4, 8, 14, 16 };
>> +
>> +static int tegra_nand_get_strength(struct nand_chip *chip, const int
>> *strength, +				   int strength_len, int oobsize)
>> +{
>> +	bool maximize = chip->ecc.options & NAND_ECC_MAXIMIZE;
>> +	int i;
>> +
>> +	/*
>> +	 * Loop through available strengths. Backwards in case we try to
>> +	 * maximize the BCH strength.
>> +	 */
>> +	for (i = 0; i < strength_len; i++) {
>> +		int strength_sel, bytes_per_step, bytes_per_page;
>> +
>> +		if (maximize) {
>> +			strength_sel = strength[strength_len - i - 1];
>> +		} else {
>> +			strength_sel = strength[i];
>> +
>> +			if (strength_sel < chip->ecc_strength_ds)
>> +				continue;
>> +		}
>> +
>> +		bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * strength_sel,
>> +					      BITS_PER_BYTE);
>> +		bytes_per_page = round_up(bytes_per_step * chip->ecc.steps, 4);
>> +
>> +		/* Check whether strength fits OOB */
>> +		if (bytes_per_page < (oobsize - SKIP_SPARE_BYTES))
>> +			return strength_sel;
>> +	}
>> +
>> +	return -EINVAL;
>> +}
>> +
>> +static int tegra_nand_select_strength(struct nand_chip *chip, int oobsize)
>> +{
>> +	const int *strength;
>> +	int strength_len;
>> +
>> +	switch (chip->ecc.algo) {
>> +	case NAND_ECC_RS:
>> +		if (chip->options & NAND_IS_BOOT_MEDIUM) {
>> +			strength = rs_strength_bootable;
>> +			strength_len = ARRAY_SIZE(rs_strength_bootable);
>> +		} else {
>> +			strength = rs_strength;
>> +			strength_len = ARRAY_SIZE(rs_strength);
>> +		}
>> +		break;
>> +	case NAND_ECC_BCH:
>> +		if (chip->options & NAND_IS_BOOT_MEDIUM) {
>> +			strength = bch_strength_bootable;
>> +			strength_len = ARRAY_SIZE(bch_strength_bootable);
>> +		} else {
>> +			strength = bch_strength;
>> +			strength_len = ARRAY_SIZE(bch_strength);
>> +		}
>> +		break;
>> +	default:
>> +		return -EINVAL;
>> +	}
>> +
>> +	return tegra_nand_get_strength(chip, strength, strength_len, oobsize);
>> +}
>> +
>> +static int tegra_nand_chips_init(struct device *dev,
>> +				 struct tegra_nand_controller *ctrl)
>> +{
>> +	struct device_node *np = dev->of_node;
>> +	struct device_node *np_nand;
>> +	int nsels, nchips = of_get_child_count(np);
>> +	struct tegra_nand_chip *nand;
>> +	struct mtd_info *mtd;
>> +	struct nand_chip *chip;
>> +	int bits_per_step;
>> +	int ret;
>> +	u32 cs;
>> +
>> +	if (nchips != 1) {
>> +		dev_err(dev, "Currently only one NAND chip supported\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	np_nand = of_get_next_child(np, NULL);
>> +
>> +	nsels = of_property_count_elems_of_size(np_nand, "reg", sizeof(u32));
>> +	if (nsels != 1) {
>> +		dev_err(dev, "Missing/invalid reg property\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	/* Retrieve CS id, currently only single die NAND supported */
>> +	ret = of_property_read_u32(np_nand, "reg", &cs);
>> +	if (ret) {
>> +		dev_err(dev, "could not retrieve reg property: %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	nand = devm_kzalloc(dev, sizeof(*nand), GFP_KERNEL);
>> +	if (!nand)
>> +		return -ENOMEM;
>> +
>> +	nand->cs[0] = cs;
>> +
>> +	nand->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_LOW);
>> +
>> +	if (IS_ERR(nand->wp_gpio)) {
>> +		ret = PTR_ERR(nand->wp_gpio);
>> +		dev_err(dev, "Failed to request WP GPIO: %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	chip = &nand->chip;
>> +	chip->controller = &ctrl->controller;
>> +
>> +	mtd = nand_to_mtd(chip);
>> +
>> +	mtd->dev.parent = dev;
>> +	mtd->owner = THIS_MODULE;
>> +
>> +	nand_set_flash_node(chip, np_nand);
>> +
>> +	if (!mtd->name)
>> +		mtd->name = "tegra_nand";
>> +
>> +	chip->options = NAND_NO_SUBPAGE_WRITE | NAND_USE_BOUNCE_BUFFER;
>> +	chip->exec_op = tegra_nand_exec_op;
>> +	chip->select_chip = tegra_nand_select_chip;
>> +	chip->setup_data_interface = tegra_nand_setup_data_interface;
>> +
>> +	ret = nand_scan_ident(mtd, 1, NULL);
>> +	if (ret)
>> +		return ret;
>> +
>> +	if (chip->bbt_options & NAND_BBT_USE_FLASH)
>> +		chip->bbt_options |= NAND_BBT_NO_OOB;
>> +
>> +	chip->ecc.mode = NAND_ECC_HW;
>> +	chip->ecc.size = 512;
>> +	chip->ecc.steps = mtd->writesize / chip->ecc.size;
>> +	if (chip->ecc_step_ds != 512) {
>> +		dev_err(dev, "Unsupported step size %d\n", chip->ecc_step_ds);
>> +		return -EINVAL;
>> +	}
>> +
>> +	chip->ecc.read_page = tegra_nand_read_page_hwecc;
>> +	chip->ecc.write_page = tegra_nand_write_page_hwecc;
>> +	chip->ecc.read_page_raw = tegra_nand_read_page_raw;
>> +	chip->ecc.write_page_raw = tegra_nand_write_page_raw;
>> +	chip->ecc.read_oob = tegra_nand_read_oob;
>> +	chip->ecc.write_oob = tegra_nand_write_oob;
>> +
>> +	if (chip->options & NAND_BUSWIDTH_16)
>> +		nand->config |= CONFIG_BUS_WIDTH_16;
>> +
>> +	if (chip->ecc.algo == NAND_ECC_UNKNOWN) {
>> +		if (mtd->writesize < 2048)
>> +			chip->ecc.algo = NAND_ECC_RS;
>> +		else
>> +			chip->ecc.algo = NAND_ECC_BCH;
>> +	}
>> +
>> +	if (chip->ecc.algo == NAND_ECC_BCH && mtd->writesize < 2048) {
>> +		dev_err(dev, "BCH supportes 2K or 4K page size only\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	if (!chip->ecc.strength) {
>> +		ret = tegra_nand_select_strength(chip, mtd->oobsize);
>> +		if (ret < 0) {
>> +			dev_err(dev, "No valid strenght found, minimum %d\n",
>> +				chip->ecc_strength_ds);
>> +			return ret;
>> +		}
>> +
>> +		chip->ecc.strength = ret;
>> +	}
>> +
>> +	nand->config_ecc = CONFIG_PIPE_EN | CONFIG_SKIP_SPARE |
>> +			   CONFIG_SKIP_SPARE_SIZE_4;
>> +
>> +	switch (chip->ecc.algo) {
>> +	case NAND_ECC_RS:
>> +		bits_per_step = BITS_PER_STEP_RS * chip->ecc.strength;
>> +		mtd_set_ooblayout(mtd, &tegra_nand_oob_rs_ops);
>> +		nand->config_ecc |= CONFIG_HW_ECC | CONFIG_ECC_SEL |
>> +				    CONFIG_ERR_COR;
>> +		switch (chip->ecc.strength) {
>> +		case 4:
>> +			nand->config_ecc |= CONFIG_TVAL_4;
>> +			break;
>> +		case 6:
>> +			nand->config_ecc |= CONFIG_TVAL_6;
>> +			break;
>> +		case 8:
>> +			nand->config_ecc |= CONFIG_TVAL_8;
>> +			break;
>> +		default:
>> +			dev_err(dev, "ECC strength %d not supported\n",
>> +				chip->ecc.strength);
>> +			return -EINVAL;
>> +		}
>> +		break;
>> +	case NAND_ECC_BCH:
>> +		bits_per_step = BITS_PER_STEP_BCH * chip->ecc.strength;
>> +		mtd_set_ooblayout(mtd, &tegra_nand_oob_bch_ops);
>> +		nand->bch_config = BCH_ENABLE;
>> +		switch (chip->ecc.strength) {
>> +		case 4:
>> +			nand->bch_config |= BCH_TVAL_4;
>> +			break;
>> +		case 8:
>> +			nand->bch_config |= BCH_TVAL_8;
>> +			break;
>> +		case 14:
>> +			nand->bch_config |= BCH_TVAL_14;
>> +			break;
>> +		case 16:
>> +			nand->bch_config |= BCH_TVAL_16;
>> +			break;
>> +		default:
>> +			dev_err(dev, "ECC strength %d not supported\n",
>> +				chip->ecc.strength);
>> +			return -EINVAL;
>> +		}
>> +		break;
>> +	default:
>> +		dev_err(dev, "ECC algorithm not supported\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	dev_info(dev, "Using %s with strength %d per 512 byte step\n",
>> +			chip->ecc.algo == NAND_ECC_BCH ? "BCH" : "RS",
>> +			chip->ecc.strength);
>> +
>> +	chip->ecc.bytes = DIV_ROUND_UP(bits_per_step, BITS_PER_BYTE);
>> +
>> +	switch (mtd->writesize) {
>> +	case 256:
>> +		nand->config |= CONFIG_PS_256;
>> +		break;
>> +	case 512:
>> +		nand->config |= CONFIG_PS_512;
>> +		break;
>> +	case 1024:
>> +		nand->config |= CONFIG_PS_1024;
>> +		break;
>> +	case 2048:
>> +		nand->config |= CONFIG_PS_2048;
>> +		break;
>> +	case 4096:
>> +		nand->config |= CONFIG_PS_4096;
>> +		break;
>> +	default:
>> +		dev_err(dev, "Unsupported writesize %d\n", mtd->writesize);
>> +		return -ENODEV;
>> +	}
>> +
>> +	/* Store complete configuration in config_ecc */
>> +	nand->config_ecc |= nand->config;
>> +
>> +	/* Non-HW ECC read/writes complete OOB */
>> +	nand->config |= CONFIG_TAG_BYTE_SIZE(mtd->oobsize - 1);
>> +	writel_relaxed(nand->config, ctrl->regs + CONFIG);
>> +
>> +	ret = nand_scan_tail(mtd);
>> +	if (ret)
>> +		return ret;
>> +
>> +	/* Store tag layout when using HW ECC */
>> +	mtd_ooblayout_free(mtd, 0, &nand->tag);
>> +	nand->config_ecc |= CONFIG_TAG_BYTE_SIZE(nand->tag.length - 1);
>> +
>> +	ret = mtd_device_register(mtd, NULL, 0);
>> +	if (ret) {
>> +		dev_err(dev, "Failed to register mtd device: %d\n", ret);
>> +		nand_cleanup(chip);
>> +		return ret;
>> +	}
>> +
>> +	ctrl->chip = chip;
>> +
>> +	return 0;
>> +}
>> +
>> +static int tegra_nand_probe(struct platform_device *pdev)
>> +{
>> +	struct reset_control *rst;
>> +	struct tegra_nand_controller *ctrl;
>> +	struct resource *res;
>> +	int err = 0;
>> +
>> +	ctrl = devm_kzalloc(&pdev->dev, sizeof(*ctrl), GFP_KERNEL);
>> +	if (!ctrl)
>> +		return -ENOMEM;
>> +
>> +	ctrl->dev = &pdev->dev;
>> +	nand_hw_control_init(&ctrl->controller);
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	ctrl->regs = devm_ioremap_resource(&pdev->dev, res);
>> +	if (IS_ERR(ctrl->regs))
>> +		return PTR_ERR(ctrl->regs);
>> +
>> +	rst = devm_reset_control_get(&pdev->dev, "nand");
>> +	if (IS_ERR(rst))
>> +		return PTR_ERR(rst);
>> +
>> +	ctrl->clk = devm_clk_get(&pdev->dev, "nand");
>> +	if (IS_ERR(ctrl->clk))
>> +		return PTR_ERR(ctrl->clk);
>> +
>> +	err = clk_prepare_enable(ctrl->clk);
>> +	if (err)
>> +		return err;
>> +
>> +	err = reset_control_reset(rst);
>> +	if (err) {
>> +		dev_err(ctrl->dev, "Failed to reset HW: %d\n", err);
>> +		goto err_disable_clk;
>> +	}
>> +
>> +	writel_relaxed(HWSTATUS_CMD_DEFAULT, ctrl->regs + HWSTATUS_CMD);
>> +	writel_relaxed(HWSTATUS_MASK_DEFAULT, ctrl->regs + HWSTATUS_MASK);
>> +	writel_relaxed(INT_MASK, ctrl->regs + IER);
>> +
>> +	init_completion(&ctrl->command_complete);
>> +	init_completion(&ctrl->dma_complete);
>> +
>> +	ctrl->irq = platform_get_irq(pdev, 0);
>> +	err = devm_request_irq(&pdev->dev, ctrl->irq, tegra_nand_irq, 0,
>> +			       dev_name(&pdev->dev), ctrl);
>> +	if (err) {
>> +		dev_err(ctrl->dev, "Failed to get IRQ: %d\n", err);
>> +		goto err_disable_clk;
>> +	}
>> +
>> +	writel_relaxed(DMA_MST_CTRL_IS_DONE, ctrl->regs + DMA_MST_CTRL);
>> +
>> +	err = tegra_nand_chips_init(ctrl->dev, ctrl);
>> +	if (err)
>> +		goto err_disable_clk;
>> +
>> +	platform_set_drvdata(pdev, ctrl);
>> +
>> +	return 0;
>> +
>> +err_disable_clk:
>> +	clk_disable_unprepare(ctrl->clk);
>> +	return err;
>> +}
>> +
>> +static int tegra_nand_remove(struct platform_device *pdev)
>> +{
>> +	struct tegra_nand_controller *ctrl = platform_get_drvdata(pdev);
>> +
>> +	nand_release(nand_to_mtd(ctrl->chip));
>> +
>> +	clk_disable_unprepare(ctrl->clk);
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct of_device_id tegra_nand_of_match[] = {
>> +	{ .compatible = "nvidia,tegra20-nand" },
>> +	{ /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, tegra_nand_of_match);
>> +
>> +static struct platform_driver tegra_nand_driver = {
>> +	.driver = {
>> +		.name = "tegra-nand",
>> +		.of_match_table = tegra_nand_of_match,
>> +	},
>> +	.probe = tegra_nand_probe,
>> +	.remove = tegra_nand_remove,
>> +};
>> +module_platform_driver(tegra_nand_driver);
>> +
>> +MODULE_DESCRIPTION("NVIDIA Tegra NAND driver");
>> +MODULE_AUTHOR("Thierry Reding <thierry.reding@nvidia.com>");
>> +MODULE_AUTHOR("Lucas Stach <dev@lynxeye.de>");
>> +MODULE_AUTHOR("Stefan Agner <stefan@agner.ch>");
>> +MODULE_LICENSE("GPL v2");

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  0:03   ` Dmitry Osipenko
@ 2018-06-12  8:06     ` Stefan Agner
  2018-06-12  8:27       ` Boris Brezillon
  0 siblings, 1 reply; 24+ messages in thread
From: Stefan Agner @ 2018-06-12  8:06 UTC (permalink / raw)
  To: Dmitry Osipenko, boris.brezillon
  Cc: dwmw2, computersforpeace, marek.vasut, robh+dt, mark.rutland,
	thierry.reding, dev, miquel.raynal, richard, marcel, krzk,
	benjamin.lindqvist, jonathanh, pdeschrijver, pgaikwad,
	mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On 12.06.2018 02:03, Dmitry Osipenko wrote:
> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>> Add support for the NAND flash controller found on NVIDIA
>> Tegra 2 SoCs. This implementation does not make use of the
>> command queue feature. Regular operations/data transfers are
>> done in PIO mode. Page read/writes with hardware ECC make
>> use of the DMA for data transfer.
>>
>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>>  MAINTAINERS                       |    7 +
>>  drivers/mtd/nand/raw/Kconfig      |    6 +
>>  drivers/mtd/nand/raw/Makefile     |    1 +
>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>>  4 files changed, 1262 insertions(+)
>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>>
[snip]
>> +static int tegra_nand_cmd(struct nand_chip *chip,
>> +			 const struct nand_subop *subop)
>> +{
>> +	const struct nand_op_instr *instr;
>> +	const struct nand_op_instr *instr_data_in = NULL;
>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> +	unsigned int op_id, size = 0, offset = 0;
>> +	bool first_cmd = true;
>> +	u32 reg, cmd = 0;
>> +	int ret;
>> +
>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>> +		unsigned int naddrs, i;
>> +		const u8 *addrs;
>> +		u32 addr1 = 0, addr2 = 0;
>> +
>> +		instr = &subop->instrs[op_id];
>> +
>> +		switch (instr->type) {
>> +		case NAND_OP_CMD_INSTR:
>> +			if (first_cmd) {
>> +				cmd |= COMMAND_CLE;
>> +				writel_relaxed(instr->ctx.cmd.opcode,
>> +					       ctrl->regs + CMD_REG1);
>> +			} else {
>> +				cmd |= COMMAND_SEC_CMD;
>> +				writel_relaxed(instr->ctx.cmd.opcode,
>> +					       ctrl->regs + CMD_REG2);
>> +			}
>> +			first_cmd = false;
>> +			break;
>> +		case NAND_OP_ADDR_INSTR:
>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>> +			addrs = &instr->ctx.addr.addrs[offset];
>> +
>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>> +			naddrs -= i;
>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>> +			break;
>> +
>> +		case NAND_OP_DATA_IN_INSTR:
>> +			size = nand_subop_get_data_len(subop, op_id);
>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>> +
>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> +				COMMAND_RX | COMMAND_A_VALID;
>> +
>> +			instr_data_in = instr;
>> +			break;
>> +
>> +		case NAND_OP_DATA_OUT_INSTR:
>> +			size = nand_subop_get_data_len(subop, op_id);
>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>> +
>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> +				COMMAND_TX | COMMAND_A_VALID;
>> +
>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
>> +			writel_relaxed(reg, ctrl->regs + RESP);
>> +
>> +			break;
>> +		case NAND_OP_WAITRDY_INSTR:
>> +			cmd |= COMMAND_RBSY_CHK;
>> +			break;
>> +
>> +		}
>> +	}
>> +
>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>> +					     msecs_to_jiffies(500));
> 
> It's not obvious to me whether _io_ variant is appropriate to use here, would 
> be nice if somebody could clarify that. Maybe block/ already does the IO 
> accounting itself and hence the IO time would be counted twice in that case.

Good that you bring this up.

I don't think that there is any higher layer which could take care of
accounting. Usually, with raw nand there is no block layer involved
anyway.

In a quick test it seems that only when using wait_for_completion_io I/O
is properly accounted in the "wait" section of top.

So far only a single driver (omap2) used the _io variant, but I think it
is the right thing to do! After all, it is I/O...

Boris or any other MTD maintainer, any comment on this?

--
Stefan

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  8:02     ` Stefan Agner
@ 2018-06-12  8:13       ` Boris Brezillon
  2018-06-17 16:57         ` Stefan Agner
  0 siblings, 1 reply; 24+ messages in thread
From: Boris Brezillon @ 2018-06-12  8:13 UTC (permalink / raw)
  To: Stefan Agner
  Cc: Dmitry Osipenko, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On Tue, 12 Jun 2018 10:02:12 +0200
Stefan Agner <stefan@agner.ch> wrote:

> >> +static int tegra_nand_read_page_hwecc(struct mtd_info *mtd,
> >> +				      struct nand_chip *chip,
> >> +				      uint8_t *buf, int oob_required, int page)
> >> +{
> >> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> >> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
> >> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
> >> +	u32 dec_stat, max_corr_cnt;
> >> +	unsigned long fail_sec_flag;
> >> +	int ret;
> >> +
> >> +	tegra_nand_hw_ecc(ctrl, chip, true);
> >> +	ret = tegra_nand_page_xfer(mtd, chip, buf, oob_buf, nand->tag.length,
> >> +				   page, true);
> >> +	tegra_nand_hw_ecc(ctrl, chip, false);
> >> +	if (ret)
> >> +		return ret;
> >> +
> >> +	/* No correctable or un-correctable errors, page must have 0 bitflips */
> >> +	if (!ctrl->last_read_error)
> >> +		return 0;
> >> +
> >> +	/*
> >> +	 * Correctable or un-correctable errors occurred. Use DEC_STAT_BUF
> >> +	 * which contains information for all ECC selections.
> >> +	 *
> >> +	 * Note that since we do not use Command Queues DEC_RESULT does not
> >> +	 * state the number of pages we can read from the DEC_STAT_BUF. But
> >> +	 * since CORRFAIL_ERR did occur during page read we do have a valid
> >> +	 * result in DEC_STAT_BUF.
> >> +	 */
> >> +	ctrl->last_read_error = false;
> >> +	dec_stat = readl_relaxed(ctrl->regs + DEC_STAT_BUF);
> >> +
> >> +	fail_sec_flag = (dec_stat & DEC_STAT_BUF_FAIL_SEC_FLAG_MASK) >>
> >> +			DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT;
> >> +
> >> +	max_corr_cnt = (dec_stat & DEC_STAT_BUF_MAX_CORR_CNT_MASK) >>
> >> +		       DEC_STAT_BUF_MAX_CORR_CNT_SHIFT;
> >> +
> >> +	if (fail_sec_flag) {
> >> +		int bit, max_bitflips = 0;
> >> +
> >> +		/*
> >> +		 * Check if all sectors in a page failed. If only some failed
> >> +		 * its definitly not an erased page and we can return error
> >> +		 * stats right away.
> >> +		 *
> >> +		 * E.g. controller might return fail_sec_flag with 0x4, which
> >> +		 * would mean only the third sector failed to correct.

That works because you have NAND_NO_SUBPAGE_WRITE set (i.e. no partial
page programming), probably something you should state here.

> >> +		 */
> >> +		if (fail_sec_flag ^ GENMASK(chip->ecc.steps - 1, 0)) {
> >> +			mtd->ecc_stats.failed += hweight8(fail_sec_flag);
> >> +			return max_corr_cnt;
> >> +		}
> >> +
> >> +		/*
> >> +		 * All sectors failed to correct, but the ECC isn't smart
> >> +		 * enough to figure out if a page is really completely erased.
> >> +		 * We check the read data here to figure out if it's a
> >> +		 * legitimate ECC error or only an erased page.
> >> +		 */
> >> +		for_each_set_bit(bit, &fail_sec_flag, chip->ecc.steps) {
> >> +			u8 *data = buf + (chip->ecc.size * bit);
> >> +
> >> +			ret = nand_check_erased_ecc_chunk(data, chip->ecc.size,
> >> +							  NULL, 0,

You should also check that the ECC bytes are 0xff here, otherwise you
won't detect corruption of pages almost filled 0xff but with a few bits
set to 0.

When you use nand_check_erased_ecc_chunk(), it's important to always
pass the data along with its associated ECC bytes.

> >> +							  NULL, 0,

If you support writing extra OOB bytes, you should also pass them here.

> >> +							  chip->ecc.strength);
> >> +			if (ret < 0)
> >> +				mtd->ecc_stats.failed++;
> >> +			else
> >> +				max_bitflips = max(ret, max_bitflips);
> >> +		}
> >> +
> >> +		return max_t(unsigned int, max_corr_cnt, max_bitflips);
> >> +	} else {
> >> +		int corr_sec_flag;
> >> +
> >> +		corr_sec_flag = (dec_stat & DEC_STAT_BUF_CORR_SEC_FLAG_MASK) >>
> >> +				DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT;
> >> +
> >> +		/*
> >> +		 * The value returned in the register is the maximum of
> >> +		 * bitflips encountered in any of the ECC regions. As there is
> >> +		 * no way to get the number of bitflips in a specific regions
> >> +		 * we are not able to deliver correct stats but instead
> >> +		 * overestimate the number of corrected bitflips by assuming
> >> +		 * that all regions where errors have been corrected
> >> +		 * encountered the maximum number of bitflips.
> >> +		 */
> >> +		mtd->ecc_stats.corrected += max_corr_cnt * hweight8(corr_sec_flag);
> >> +
> >> +		return max_corr_cnt;
> >> +	}
> >> +  


^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  8:06     ` Stefan Agner
@ 2018-06-12  8:27       ` Boris Brezillon
  2018-06-12  9:17         ` Stefan Agner
  0 siblings, 1 reply; 24+ messages in thread
From: Boris Brezillon @ 2018-06-12  8:27 UTC (permalink / raw)
  To: Stefan Agner
  Cc: Dmitry Osipenko, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On Tue, 12 Jun 2018 10:06:42 +0200
Stefan Agner <stefan@agner.ch> wrote:

> On 12.06.2018 02:03, Dmitry Osipenko wrote:
> > On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:  
> >> Add support for the NAND flash controller found on NVIDIA
> >> Tegra 2 SoCs. This implementation does not make use of the
> >> command queue feature. Regular operations/data transfers are
> >> done in PIO mode. Page read/writes with hardware ECC make
> >> use of the DMA for data transfer.
> >>
> >> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> >> Signed-off-by: Stefan Agner <stefan@agner.ch>
> >> ---
> >>  MAINTAINERS                       |    7 +
> >>  drivers/mtd/nand/raw/Kconfig      |    6 +
> >>  drivers/mtd/nand/raw/Makefile     |    1 +
> >>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
> >>  4 files changed, 1262 insertions(+)
> >>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> >>  
> [snip]
> >> +static int tegra_nand_cmd(struct nand_chip *chip,
> >> +			 const struct nand_subop *subop)
> >> +{
> >> +	const struct nand_op_instr *instr;
> >> +	const struct nand_op_instr *instr_data_in = NULL;
> >> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> >> +	unsigned int op_id, size = 0, offset = 0;
> >> +	bool first_cmd = true;
> >> +	u32 reg, cmd = 0;
> >> +	int ret;
> >> +
> >> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
> >> +		unsigned int naddrs, i;
> >> +		const u8 *addrs;
> >> +		u32 addr1 = 0, addr2 = 0;
> >> +
> >> +		instr = &subop->instrs[op_id];
> >> +
> >> +		switch (instr->type) {
> >> +		case NAND_OP_CMD_INSTR:
> >> +			if (first_cmd) {
> >> +				cmd |= COMMAND_CLE;
> >> +				writel_relaxed(instr->ctx.cmd.opcode,
> >> +					       ctrl->regs + CMD_REG1);
> >> +			} else {
> >> +				cmd |= COMMAND_SEC_CMD;
> >> +				writel_relaxed(instr->ctx.cmd.opcode,
> >> +					       ctrl->regs + CMD_REG2);
> >> +			}
> >> +			first_cmd = false;
> >> +			break;
> >> +		case NAND_OP_ADDR_INSTR:
> >> +			offset = nand_subop_get_addr_start_off(subop, op_id);
> >> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
> >> +			addrs = &instr->ctx.addr.addrs[offset];
> >> +
> >> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
> >> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
> >> +			naddrs -= i;
> >> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
> >> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> >> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
> >> +			break;
> >> +
> >> +		case NAND_OP_DATA_IN_INSTR:
> >> +			size = nand_subop_get_data_len(subop, op_id);
> >> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >> +
> >> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >> +				COMMAND_RX | COMMAND_A_VALID;
> >> +
> >> +			instr_data_in = instr;
> >> +			break;
> >> +
> >> +		case NAND_OP_DATA_OUT_INSTR:
> >> +			size = nand_subop_get_data_len(subop, op_id);
> >> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >> +
> >> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >> +				COMMAND_TX | COMMAND_A_VALID;
> >> +
> >> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
> >> +			writel_relaxed(reg, ctrl->regs + RESP);
> >> +
> >> +			break;
> >> +		case NAND_OP_WAITRDY_INSTR:
> >> +			cmd |= COMMAND_RBSY_CHK;
> >> +			break;
> >> +
> >> +		}
> >> +	}
> >> +
> >> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
> >> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> >> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> >> +					     msecs_to_jiffies(500));  
> > 
> > It's not obvious to me whether _io_ variant is appropriate to use here, would 
> > be nice if somebody could clarify that. Maybe block/ already does the IO 
> > accounting itself and hence the IO time would be counted twice in that case.  
> 
> Good that you bring this up.
> 
> I don't think that there is any higher layer which could take care of
> accounting. Usually, with raw nand there is no block layer involved
> anyway.
> 
> In a quick test it seems that only when using wait_for_completion_io I/O
> is properly accounted in the "wait" section of top.
> 
> So far only a single driver (omap2) used the _io variant, but I think it
> is the right thing to do! After all, it is I/O...
> 
> Boris or any other MTD maintainer, any comment on this?

Given this definition of io_schedule_timeout() [1] (which is used when
you call wait_for_completion_io_timeout()), I'd say it's not useful to
use the _io_ version, simply because MTD devs are not exposed as blk
devices, and thus don't need the blk_schedule_flush_plug() that is done
is io_schedule_prepare(). But that also means MTD I/Os are not
accounted as I/Os :-(.

Let's go for the non-io version for now, since all drivers except omap2
seem to use this function.

[1]https://elixir.bootlin.com/linux/v4.17.1/source/kernel/sched/core.c#L5164

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  8:27       ` Boris Brezillon
@ 2018-06-12  9:17         ` Stefan Agner
  2018-06-12  9:34           ` Boris Brezillon
  2018-06-12 15:24           ` Jens Axboe
  0 siblings, 2 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-12  9:17 UTC (permalink / raw)
  To: Boris Brezillon, axboe
  Cc: Dmitry Osipenko, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

[also added Jens Axboe]

On 12.06.2018 10:27, Boris Brezillon wrote:
> On Tue, 12 Jun 2018 10:06:42 +0200
> Stefan Agner <stefan@agner.ch> wrote:
> 
>> On 12.06.2018 02:03, Dmitry Osipenko wrote:
>> > On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>> >> Add support for the NAND flash controller found on NVIDIA
>> >> Tegra 2 SoCs. This implementation does not make use of the
>> >> command queue feature. Regular operations/data transfers are
>> >> done in PIO mode. Page read/writes with hardware ECC make
>> >> use of the DMA for data transfer.
>> >>
>> >> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>> >> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> >> ---
>> >>  MAINTAINERS                       |    7 +
>> >>  drivers/mtd/nand/raw/Kconfig      |    6 +
>> >>  drivers/mtd/nand/raw/Makefile     |    1 +
>> >>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>> >>  4 files changed, 1262 insertions(+)
>> >>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>> >>
>> [snip]
>> >> +static int tegra_nand_cmd(struct nand_chip *chip,
>> >> +			 const struct nand_subop *subop)
>> >> +{
>> >> +	const struct nand_op_instr *instr;
>> >> +	const struct nand_op_instr *instr_data_in = NULL;
>> >> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> >> +	unsigned int op_id, size = 0, offset = 0;
>> >> +	bool first_cmd = true;
>> >> +	u32 reg, cmd = 0;
>> >> +	int ret;
>> >> +
>> >> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>> >> +		unsigned int naddrs, i;
>> >> +		const u8 *addrs;
>> >> +		u32 addr1 = 0, addr2 = 0;
>> >> +
>> >> +		instr = &subop->instrs[op_id];
>> >> +
>> >> +		switch (instr->type) {
>> >> +		case NAND_OP_CMD_INSTR:
>> >> +			if (first_cmd) {
>> >> +				cmd |= COMMAND_CLE;
>> >> +				writel_relaxed(instr->ctx.cmd.opcode,
>> >> +					       ctrl->regs + CMD_REG1);
>> >> +			} else {
>> >> +				cmd |= COMMAND_SEC_CMD;
>> >> +				writel_relaxed(instr->ctx.cmd.opcode,
>> >> +					       ctrl->regs + CMD_REG2);
>> >> +			}
>> >> +			first_cmd = false;
>> >> +			break;
>> >> +		case NAND_OP_ADDR_INSTR:
>> >> +			offset = nand_subop_get_addr_start_off(subop, op_id);
>> >> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>> >> +			addrs = &instr->ctx.addr.addrs[offset];
>> >> +
>> >> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>> >> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> >> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>> >> +			naddrs -= i;
>> >> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> >> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>> >> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>> >> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>> >> +			break;
>> >> +
>> >> +		case NAND_OP_DATA_IN_INSTR:
>> >> +			size = nand_subop_get_data_len(subop, op_id);
>> >> +			offset = nand_subop_get_data_start_off(subop, op_id);
>> >> +
>> >> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> >> +				COMMAND_RX | COMMAND_A_VALID;
>> >> +
>> >> +			instr_data_in = instr;
>> >> +			break;
>> >> +
>> >> +		case NAND_OP_DATA_OUT_INSTR:
>> >> +			size = nand_subop_get_data_len(subop, op_id);
>> >> +			offset = nand_subop_get_data_start_off(subop, op_id);
>> >> +
>> >> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> >> +				COMMAND_TX | COMMAND_A_VALID;
>> >> +
>> >> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
>> >> +			writel_relaxed(reg, ctrl->regs + RESP);
>> >> +
>> >> +			break;
>> >> +		case NAND_OP_WAITRDY_INSTR:
>> >> +			cmd |= COMMAND_RBSY_CHK;
>> >> +			break;
>> >> +
>> >> +		}
>> >> +	}
>> >> +
>> >> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>> >> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>> >> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>> >> +					     msecs_to_jiffies(500));
>> >
>> > It's not obvious to me whether _io_ variant is appropriate to use here, would
>> > be nice if somebody could clarify that. Maybe block/ already does the IO
>> > accounting itself and hence the IO time would be counted twice in that case.
>>
>> Good that you bring this up.
>>
>> I don't think that there is any higher layer which could take care of
>> accounting. Usually, with raw nand there is no block layer involved
>> anyway.
>>
>> In a quick test it seems that only when using wait_for_completion_io I/O
>> is properly accounted in the "wait" section of top.
>>
>> So far only a single driver (omap2) used the _io variant, but I think it
>> is the right thing to do! After all, it is I/O...
>>
>> Boris or any other MTD maintainer, any comment on this?
> 
> Given this definition of io_schedule_timeout() [1] (which is used when
> you call wait_for_completion_io_timeout()), I'd say it's not useful to
> use the _io_ version, simply because MTD devs are not exposed as blk
> devices, and thus don't need the blk_schedule_flush_plug() that is done
> is io_schedule_prepare(). But that also means MTD I/Os are not
> accounted as I/Os :-(.

Documentation of wait_for_completion_io says:
"The caller is accounted as waiting for IO (which traditionally means
blkio only)."

Which sounds as if it using _io is only an accounting thing...

The hint about blkio might suggest that there is more to it.

Is calling blk_schedule_flush_plug a problem for MTD?
https://elixir.bootlin.com/linux/v4.17.1/source/include/linux/blkdev.h#L1355

> 
> Let's go for the non-io version for now, since all drivers except omap2
> seem to use this function.
> 

I still think it would be nice and "the right thing" from a user
perspective...

--
Stefan

> [1]https://elixir.bootlin.com/linux/v4.17.1/source/kernel/sched/core.c#L5164

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  9:17         ` Stefan Agner
@ 2018-06-12  9:34           ` Boris Brezillon
  2018-06-12 15:24           ` Jens Axboe
  1 sibling, 0 replies; 24+ messages in thread
From: Boris Brezillon @ 2018-06-12  9:34 UTC (permalink / raw)
  To: Stefan Agner
  Cc: axboe, Dmitry Osipenko, dwmw2, computersforpeace, marek.vasut,
	robh+dt, mark.rutland, thierry.reding, dev, miquel.raynal,
	richard, marcel, krzk, benjamin.lindqvist, jonathanh,
	pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel

On Tue, 12 Jun 2018 11:17:09 +0200
Stefan Agner <stefan@agner.ch> wrote:

> [also added Jens Axboe]
> 
> On 12.06.2018 10:27, Boris Brezillon wrote:
> > On Tue, 12 Jun 2018 10:06:42 +0200
> > Stefan Agner <stefan@agner.ch> wrote:
> >   
> >> On 12.06.2018 02:03, Dmitry Osipenko wrote:  
> >> > On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:  
> >> >> Add support for the NAND flash controller found on NVIDIA
> >> >> Tegra 2 SoCs. This implementation does not make use of the
> >> >> command queue feature. Regular operations/data transfers are
> >> >> done in PIO mode. Page read/writes with hardware ECC make
> >> >> use of the DMA for data transfer.
> >> >>
> >> >> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> >> >> Signed-off-by: Stefan Agner <stefan@agner.ch>
> >> >> ---
> >> >>  MAINTAINERS                       |    7 +
> >> >>  drivers/mtd/nand/raw/Kconfig      |    6 +
> >> >>  drivers/mtd/nand/raw/Makefile     |    1 +
> >> >>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
> >> >>  4 files changed, 1262 insertions(+)
> >> >>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> >> >>  
> >> [snip]  
> >> >> +static int tegra_nand_cmd(struct nand_chip *chip,
> >> >> +			 const struct nand_subop *subop)
> >> >> +{
> >> >> +	const struct nand_op_instr *instr;
> >> >> +	const struct nand_op_instr *instr_data_in = NULL;
> >> >> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> >> >> +	unsigned int op_id, size = 0, offset = 0;
> >> >> +	bool first_cmd = true;
> >> >> +	u32 reg, cmd = 0;
> >> >> +	int ret;
> >> >> +
> >> >> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
> >> >> +		unsigned int naddrs, i;
> >> >> +		const u8 *addrs;
> >> >> +		u32 addr1 = 0, addr2 = 0;
> >> >> +
> >> >> +		instr = &subop->instrs[op_id];
> >> >> +
> >> >> +		switch (instr->type) {
> >> >> +		case NAND_OP_CMD_INSTR:
> >> >> +			if (first_cmd) {
> >> >> +				cmd |= COMMAND_CLE;
> >> >> +				writel_relaxed(instr->ctx.cmd.opcode,
> >> >> +					       ctrl->regs + CMD_REG1);
> >> >> +			} else {
> >> >> +				cmd |= COMMAND_SEC_CMD;
> >> >> +				writel_relaxed(instr->ctx.cmd.opcode,
> >> >> +					       ctrl->regs + CMD_REG2);
> >> >> +			}
> >> >> +			first_cmd = false;
> >> >> +			break;
> >> >> +		case NAND_OP_ADDR_INSTR:
> >> >> +			offset = nand_subop_get_addr_start_off(subop, op_id);
> >> >> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
> >> >> +			addrs = &instr->ctx.addr.addrs[offset];
> >> >> +
> >> >> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
> >> >> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >> >> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
> >> >> +			naddrs -= i;
> >> >> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >> >> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
> >> >> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> >> >> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
> >> >> +			break;
> >> >> +
> >> >> +		case NAND_OP_DATA_IN_INSTR:
> >> >> +			size = nand_subop_get_data_len(subop, op_id);
> >> >> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >> >> +
> >> >> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >> >> +				COMMAND_RX | COMMAND_A_VALID;
> >> >> +
> >> >> +			instr_data_in = instr;
> >> >> +			break;
> >> >> +
> >> >> +		case NAND_OP_DATA_OUT_INSTR:
> >> >> +			size = nand_subop_get_data_len(subop, op_id);
> >> >> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >> >> +
> >> >> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >> >> +				COMMAND_TX | COMMAND_A_VALID;
> >> >> +
> >> >> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
> >> >> +			writel_relaxed(reg, ctrl->regs + RESP);
> >> >> +
> >> >> +			break;
> >> >> +		case NAND_OP_WAITRDY_INSTR:
> >> >> +			cmd |= COMMAND_RBSY_CHK;
> >> >> +			break;
> >> >> +
> >> >> +		}
> >> >> +	}
> >> >> +
> >> >> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
> >> >> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> >> >> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> >> >> +					     msecs_to_jiffies(500));  
> >> >
> >> > It's not obvious to me whether _io_ variant is appropriate to use here, would
> >> > be nice if somebody could clarify that. Maybe block/ already does the IO
> >> > accounting itself and hence the IO time would be counted twice in that case.  
> >>
> >> Good that you bring this up.
> >>
> >> I don't think that there is any higher layer which could take care of
> >> accounting. Usually, with raw nand there is no block layer involved
> >> anyway.
> >>
> >> In a quick test it seems that only when using wait_for_completion_io I/O
> >> is properly accounted in the "wait" section of top.
> >>
> >> So far only a single driver (omap2) used the _io variant, but I think it
> >> is the right thing to do! After all, it is I/O...
> >>
> >> Boris or any other MTD maintainer, any comment on this?  
> > 
> > Given this definition of io_schedule_timeout() [1] (which is used when
> > you call wait_for_completion_io_timeout()), I'd say it's not useful to
> > use the _io_ version, simply because MTD devs are not exposed as blk
> > devices, and thus don't need the blk_schedule_flush_plug() that is done
> > is io_schedule_prepare(). But that also means MTD I/Os are not
> > accounted as I/Os :-(.  
> 
> Documentation of wait_for_completion_io says:
> "The caller is accounted as waiting for IO (which traditionally means
> blkio only)."
> 
> Which sounds as if it using _io is only an accounting thing...
> 
> The hint about blkio might suggest that there is more to it.
> 
> Is calling blk_schedule_flush_plug a problem for MTD?
> https://elixir.bootlin.com/linux/v4.17.1/source/include/linux/blkdev.h#L1355

It shouldn't. It might add a bit of work when a blk_plug is attached to
the task that is about to wait for I/Os (I honestly don't know what a
blk_plug is :-)).

> 
> > 
> > Let's go for the non-io version for now, since all drivers except omap2
> > seem to use this function.
> >   
> 
> I still think it would be nice and "the right thing" from a user
> perspective...

If we decide to switch to wait_for_completion_io_timeout(), I'd prefer
to do that for all drivers rather than just this one, and I'm still not
sure this is the right thing to do given the comment you pointed out
("which traditionally means blkio only").

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
                     ` (2 preceding siblings ...)
  2018-06-12  0:03   ` Dmitry Osipenko
@ 2018-06-12 12:17   ` Dmitry Osipenko
  3 siblings, 0 replies; 24+ messages in thread
From: Dmitry Osipenko @ 2018-06-12 12:17 UTC (permalink / raw)
  To: Stefan Agner
  Cc: boris.brezillon, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
> Add support for the NAND flash controller found on NVIDIA
> Tegra 2 SoCs. This implementation does not make use of the
> command queue feature. Regular operations/data transfers are
> done in PIO mode. Page read/writes with hardware ECC make
> use of the DMA for data transfer.
> 
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
>  MAINTAINERS                       |    7 +
>  drivers/mtd/nand/raw/Kconfig      |    6 +
>  drivers/mtd/nand/raw/Makefile     |    1 +
>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>  4 files changed, 1262 insertions(+)
>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 58b9861ccf99..c2e5571c85d4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13844,6 +13844,13 @@ M:	Laxman Dewangan <ldewangan@nvidia.com>
>  S:	Supported
>  F:	drivers/input/keyboard/tegra-kbc.c
> 
> +TEGRA NAND DRIVER
> +M:	Stefan Agner <stefan@agner.ch>
> +M:	Lucas Stach <dev@lynxeye.de>
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
> +F:	drivers/mtd/nand/raw/tegra_nand.c
> +
>  TEGRA PWM DRIVER
>  M:	Thierry Reding <thierry.reding@gmail.com>
>  S:	Supported
> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
> index 19a2b283fbbe..e9093f52371e 100644
> --- a/drivers/mtd/nand/raw/Kconfig
> +++ b/drivers/mtd/nand/raw/Kconfig
> @@ -534,4 +534,10 @@ config MTD_NAND_MTK
>  	  Enables support for NAND controller on MTK SoCs.
>  	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
> 
> +config MTD_NAND_TEGRA
> +	tristate "Support for NAND controller on NVIDIA Tegra"
> +	depends on ARCH_TEGRA || COMPILE_TEST
> +	help
> +	  Enables support for NAND flash controller on NVIDIA Tegra SoC.
> +
>  endif # MTD_NAND
> diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
> index 165b7ef9e9a1..d5a5f9832b88 100644
> --- a/drivers/mtd/nand/raw/Makefile
> +++ b/drivers/mtd/nand/raw/Makefile
> @@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504)	        += 
hisi504_nand.o
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
>  obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
>  obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
> +obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
> 
>  nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
>  nand-objs += nand_amd.o
> diff --git a/drivers/mtd/nand/raw/tegra_nand.c
> b/drivers/mtd/nand/raw/tegra_nand.c new file mode 100644
> index 000000000000..dd23a5eb6af3
> --- /dev/null
> +++ b/drivers/mtd/nand/raw/tegra_nand.c
> @@ -0,0 +1,1248 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2018 Stefan Agner <stefan@agner.ch>
> + * Copyright (C) 2014-2015 Lucas Stach <dev@lynxeye.de>
> + * Copyright (C) 2012 Avionic Design GmbH
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>

The "delay.h" looks obsolete now, maybe you could drop it.



^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  9:17         ` Stefan Agner
  2018-06-12  9:34           ` Boris Brezillon
@ 2018-06-12 15:24           ` Jens Axboe
  2018-06-12 20:20             ` Stefan Agner
  1 sibling, 1 reply; 24+ messages in thread
From: Jens Axboe @ 2018-06-12 15:24 UTC (permalink / raw)
  To: Stefan Agner, Boris Brezillon
  Cc: Dmitry Osipenko, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On 6/12/18 3:17 AM, Stefan Agner wrote:
> [also added Jens Axboe]
> 
> On 12.06.2018 10:27, Boris Brezillon wrote:
>> On Tue, 12 Jun 2018 10:06:42 +0200
>> Stefan Agner <stefan@agner.ch> wrote:
>>
>>> On 12.06.2018 02:03, Dmitry Osipenko wrote:
>>>> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>>>>> Add support for the NAND flash controller found on NVIDIA
>>>>> Tegra 2 SoCs. This implementation does not make use of the
>>>>> command queue feature. Regular operations/data transfers are
>>>>> done in PIO mode. Page read/writes with hardware ECC make
>>>>> use of the DMA for data transfer.
>>>>>
>>>>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>>>>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>>>>> ---
>>>>>  MAINTAINERS                       |    7 +
>>>>>  drivers/mtd/nand/raw/Kconfig      |    6 +
>>>>>  drivers/mtd/nand/raw/Makefile     |    1 +
>>>>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>>>>>  4 files changed, 1262 insertions(+)
>>>>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>>>>>
>>> [snip]
>>>>> +static int tegra_nand_cmd(struct nand_chip *chip,
>>>>> +			 const struct nand_subop *subop)
>>>>> +{
>>>>> +	const struct nand_op_instr *instr;
>>>>> +	const struct nand_op_instr *instr_data_in = NULL;
>>>>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>>>>> +	unsigned int op_id, size = 0, offset = 0;
>>>>> +	bool first_cmd = true;
>>>>> +	u32 reg, cmd = 0;
>>>>> +	int ret;
>>>>> +
>>>>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>>>>> +		unsigned int naddrs, i;
>>>>> +		const u8 *addrs;
>>>>> +		u32 addr1 = 0, addr2 = 0;
>>>>> +
>>>>> +		instr = &subop->instrs[op_id];
>>>>> +
>>>>> +		switch (instr->type) {
>>>>> +		case NAND_OP_CMD_INSTR:
>>>>> +			if (first_cmd) {
>>>>> +				cmd |= COMMAND_CLE;
>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
>>>>> +					       ctrl->regs + CMD_REG1);
>>>>> +			} else {
>>>>> +				cmd |= COMMAND_SEC_CMD;
>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
>>>>> +					       ctrl->regs + CMD_REG2);
>>>>> +			}
>>>>> +			first_cmd = false;
>>>>> +			break;
>>>>> +		case NAND_OP_ADDR_INSTR:
>>>>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
>>>>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>>>>> +			addrs = &instr->ctx.addr.addrs[offset];
>>>>> +
>>>>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>>>>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>>>>> +			naddrs -= i;
>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>>>>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>>>>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>>>>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>>>>> +			break;
>>>>> +
>>>>> +		case NAND_OP_DATA_IN_INSTR:
>>>>> +			size = nand_subop_get_data_len(subop, op_id);
>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>>>>> +
>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>>>>> +				COMMAND_RX | COMMAND_A_VALID;
>>>>> +
>>>>> +			instr_data_in = instr;
>>>>> +			break;
>>>>> +
>>>>> +		case NAND_OP_DATA_OUT_INSTR:
>>>>> +			size = nand_subop_get_data_len(subop, op_id);
>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>>>>> +
>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>>>>> +				COMMAND_TX | COMMAND_A_VALID;
>>>>> +
>>>>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
>>>>> +			writel_relaxed(reg, ctrl->regs + RESP);
>>>>> +
>>>>> +			break;
>>>>> +		case NAND_OP_WAITRDY_INSTR:
>>>>> +			cmd |= COMMAND_RBSY_CHK;
>>>>> +			break;
>>>>> +
>>>>> +		}
>>>>> +	}
>>>>> +
>>>>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>>>>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>>>>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>>>>> +					     msecs_to_jiffies(500));
>>>>
>>>> It's not obvious to me whether _io_ variant is appropriate to use here, would
>>>> be nice if somebody could clarify that. Maybe block/ already does the IO
>>>> accounting itself and hence the IO time would be counted twice in that case.
>>>
>>> Good that you bring this up.
>>>
>>> I don't think that there is any higher layer which could take care of
>>> accounting. Usually, with raw nand there is no block layer involved
>>> anyway.
>>>
>>> In a quick test it seems that only when using wait_for_completion_io I/O
>>> is properly accounted in the "wait" section of top.
>>>
>>> So far only a single driver (omap2) used the _io variant, but I think it
>>> is the right thing to do! After all, it is I/O...
>>>
>>> Boris or any other MTD maintainer, any comment on this?
>>
>> Given this definition of io_schedule_timeout() [1] (which is used when
>> you call wait_for_completion_io_timeout()), I'd say it's not useful to
>> use the _io_ version, simply because MTD devs are not exposed as blk
>> devices, and thus don't need the blk_schedule_flush_plug() that is done
>> is io_schedule_prepare(). But that also means MTD I/Os are not
>> accounted as I/Os :-(.
> 
> Documentation of wait_for_completion_io says:
> "The caller is accounted as waiting for IO (which traditionally means
> blkio only)."
> 
> Which sounds as if it using _io is only an accounting thing...

Yes, you should only use it for waiting for IO off a system call
read path. So block IO, or file system IO. Don't use it for internal
IO that isn't related to that.

-- 
Jens Axboe


^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm
  2018-06-11 20:52 ` [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm Stefan Agner
@ 2018-06-12 18:37   ` Rob Herring
  0 siblings, 0 replies; 24+ messages in thread
From: Rob Herring @ 2018-06-12 18:37 UTC (permalink / raw)
  To: Stefan Agner
  Cc: boris.brezillon, dwmw2, computersforpeace, marek.vasut,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, digetx, benjamin.lindqvist, jonathanh,
	pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel

On Mon, Jun 11, 2018 at 10:52:19PM +0200, Stefan Agner wrote:
> Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
> 
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
> ---
>  Documentation/devicetree/bindings/mtd/nand.txt | 2 +-

Acked-by: Rob Herring <robh@kernel.org>

>  drivers/mtd/nand/raw/nand_base.c               | 1 +
>  include/linux/mtd/rawnand.h                    | 1 +
>  3 files changed, 3 insertions(+), 1 deletion(-)

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12 15:24           ` Jens Axboe
@ 2018-06-12 20:20             ` Stefan Agner
  2018-06-12 21:20               ` Boris Brezillon
  2018-06-12 21:24               ` Jens Axboe
  0 siblings, 2 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-12 20:20 UTC (permalink / raw)
  To: Jens Axboe
  Cc: Boris Brezillon, Dmitry Osipenko, dwmw2, computersforpeace,
	marek.vasut, robh+dt, mark.rutland, thierry.reding, dev,
	miquel.raynal, richard, marcel, krzk, benjamin.lindqvist,
	jonathanh, pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel

On 12.06.2018 17:24, Jens Axboe wrote:
> On 6/12/18 3:17 AM, Stefan Agner wrote:
>> [also added Jens Axboe]
>>
>> On 12.06.2018 10:27, Boris Brezillon wrote:
>>> On Tue, 12 Jun 2018 10:06:42 +0200
>>> Stefan Agner <stefan@agner.ch> wrote:
>>>
>>>> On 12.06.2018 02:03, Dmitry Osipenko wrote:
>>>>> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>>>>>> Add support for the NAND flash controller found on NVIDIA
>>>>>> Tegra 2 SoCs. This implementation does not make use of the
>>>>>> command queue feature. Regular operations/data transfers are
>>>>>> done in PIO mode. Page read/writes with hardware ECC make
>>>>>> use of the DMA for data transfer.
>>>>>>
>>>>>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>>>>>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>>>>>> ---
>>>>>>  MAINTAINERS                       |    7 +
>>>>>>  drivers/mtd/nand/raw/Kconfig      |    6 +
>>>>>>  drivers/mtd/nand/raw/Makefile     |    1 +
>>>>>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>>>>>>  4 files changed, 1262 insertions(+)
>>>>>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>>>>>>
>>>> [snip]
>>>>>> +static int tegra_nand_cmd(struct nand_chip *chip,
>>>>>> +			 const struct nand_subop *subop)
>>>>>> +{
>>>>>> +	const struct nand_op_instr *instr;
>>>>>> +	const struct nand_op_instr *instr_data_in = NULL;
>>>>>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>>>>>> +	unsigned int op_id, size = 0, offset = 0;
>>>>>> +	bool first_cmd = true;
>>>>>> +	u32 reg, cmd = 0;
>>>>>> +	int ret;
>>>>>> +
>>>>>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>>>>>> +		unsigned int naddrs, i;
>>>>>> +		const u8 *addrs;
>>>>>> +		u32 addr1 = 0, addr2 = 0;
>>>>>> +
>>>>>> +		instr = &subop->instrs[op_id];
>>>>>> +
>>>>>> +		switch (instr->type) {
>>>>>> +		case NAND_OP_CMD_INSTR:
>>>>>> +			if (first_cmd) {
>>>>>> +				cmd |= COMMAND_CLE;
>>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
>>>>>> +					       ctrl->regs + CMD_REG1);
>>>>>> +			} else {
>>>>>> +				cmd |= COMMAND_SEC_CMD;
>>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
>>>>>> +					       ctrl->regs + CMD_REG2);
>>>>>> +			}
>>>>>> +			first_cmd = false;
>>>>>> +			break;
>>>>>> +		case NAND_OP_ADDR_INSTR:
>>>>>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
>>>>>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>>>>>> +			addrs = &instr->ctx.addr.addrs[offset];
>>>>>> +
>>>>>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>>>>>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>>>>>> +			naddrs -= i;
>>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>>>>>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>>>>>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>>>>>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>>>>>> +			break;
>>>>>> +
>>>>>> +		case NAND_OP_DATA_IN_INSTR:
>>>>>> +			size = nand_subop_get_data_len(subop, op_id);
>>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>>>>>> +
>>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>>>>>> +				COMMAND_RX | COMMAND_A_VALID;
>>>>>> +
>>>>>> +			instr_data_in = instr;
>>>>>> +			break;
>>>>>> +
>>>>>> +		case NAND_OP_DATA_OUT_INSTR:
>>>>>> +			size = nand_subop_get_data_len(subop, op_id);
>>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>>>>>> +
>>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>>>>>> +				COMMAND_TX | COMMAND_A_VALID;
>>>>>> +
>>>>>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
>>>>>> +			writel_relaxed(reg, ctrl->regs + RESP);
>>>>>> +
>>>>>> +			break;
>>>>>> +		case NAND_OP_WAITRDY_INSTR:
>>>>>> +			cmd |= COMMAND_RBSY_CHK;
>>>>>> +			break;
>>>>>> +
>>>>>> +		}
>>>>>> +	}
>>>>>> +
>>>>>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>>>>>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>>>>>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>>>>>> +					     msecs_to_jiffies(500));
>>>>>
>>>>> It's not obvious to me whether _io_ variant is appropriate to use here, would
>>>>> be nice if somebody could clarify that. Maybe block/ already does the IO
>>>>> accounting itself and hence the IO time would be counted twice in that case.
>>>>
>>>> Good that you bring this up.
>>>>
>>>> I don't think that there is any higher layer which could take care of
>>>> accounting. Usually, with raw nand there is no block layer involved
>>>> anyway.
>>>>
>>>> In a quick test it seems that only when using wait_for_completion_io I/O
>>>> is properly accounted in the "wait" section of top.
>>>>
>>>> So far only a single driver (omap2) used the _io variant, but I think it
>>>> is the right thing to do! After all, it is I/O...
>>>>
>>>> Boris or any other MTD maintainer, any comment on this?
>>>
>>> Given this definition of io_schedule_timeout() [1] (which is used when
>>> you call wait_for_completion_io_timeout()), I'd say it's not useful to
>>> use the _io_ version, simply because MTD devs are not exposed as blk
>>> devices, and thus don't need the blk_schedule_flush_plug() that is done
>>> is io_schedule_prepare(). But that also means MTD I/Os are not
>>> accounted as I/Os :-(.
>>
>> Documentation of wait_for_completion_io says:
>> "The caller is accounted as waiting for IO (which traditionally means
>> blkio only)."
>>
>> Which sounds as if it using _io is only an accounting thing...
> 
> Yes, you should only use it for waiting for IO off a system call
> read path. So block IO, or file system IO. Don't use it for internal
> IO that isn't related to that.

I guess that would be the case here, since MTD page read/writes are
typically file system IOs (e.g. UBIFS).

The problem is just that is not block related at all since it uses the
MTD subsystem... And it seems that the _io variants besides accounting,
also take a role in the block subsystems device plugging mechanism. What
is unclear to me if using the _io variant from the MTD subsystem
potentially disturbs the plugging mechanism...

--
Stefan

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12 20:20             ` Stefan Agner
@ 2018-06-12 21:20               ` Boris Brezillon
  2018-06-12 21:24               ` Jens Axboe
  1 sibling, 0 replies; 24+ messages in thread
From: Boris Brezillon @ 2018-06-12 21:20 UTC (permalink / raw)
  To: Stefan Agner
  Cc: Jens Axboe, Dmitry Osipenko, dwmw2, computersforpeace,
	marek.vasut, robh+dt, mark.rutland, thierry.reding, dev,
	miquel.raynal, richard, marcel, krzk, benjamin.lindqvist,
	jonathanh, pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel

On Tue, 12 Jun 2018 22:20:58 +0200
Stefan Agner <stefan@agner.ch> wrote:

> On 12.06.2018 17:24, Jens Axboe wrote:
> > On 6/12/18 3:17 AM, Stefan Agner wrote:  
> >> [also added Jens Axboe]
> >>
> >> On 12.06.2018 10:27, Boris Brezillon wrote:  
> >>> On Tue, 12 Jun 2018 10:06:42 +0200
> >>> Stefan Agner <stefan@agner.ch> wrote:
> >>>  
> >>>> On 12.06.2018 02:03, Dmitry Osipenko wrote:  
> >>>>> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:  
> >>>>>> Add support for the NAND flash controller found on NVIDIA
> >>>>>> Tegra 2 SoCs. This implementation does not make use of the
> >>>>>> command queue feature. Regular operations/data transfers are
> >>>>>> done in PIO mode. Page read/writes with hardware ECC make
> >>>>>> use of the DMA for data transfer.
> >>>>>>
> >>>>>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> >>>>>> Signed-off-by: Stefan Agner <stefan@agner.ch>
> >>>>>> ---
> >>>>>>  MAINTAINERS                       |    7 +
> >>>>>>  drivers/mtd/nand/raw/Kconfig      |    6 +
> >>>>>>  drivers/mtd/nand/raw/Makefile     |    1 +
> >>>>>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
> >>>>>>  4 files changed, 1262 insertions(+)
> >>>>>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> >>>>>>  
> >>>> [snip]  
> >>>>>> +static int tegra_nand_cmd(struct nand_chip *chip,
> >>>>>> +			 const struct nand_subop *subop)
> >>>>>> +{
> >>>>>> +	const struct nand_op_instr *instr;
> >>>>>> +	const struct nand_op_instr *instr_data_in = NULL;
> >>>>>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> >>>>>> +	unsigned int op_id, size = 0, offset = 0;
> >>>>>> +	bool first_cmd = true;
> >>>>>> +	u32 reg, cmd = 0;
> >>>>>> +	int ret;
> >>>>>> +
> >>>>>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
> >>>>>> +		unsigned int naddrs, i;
> >>>>>> +		const u8 *addrs;
> >>>>>> +		u32 addr1 = 0, addr2 = 0;
> >>>>>> +
> >>>>>> +		instr = &subop->instrs[op_id];
> >>>>>> +
> >>>>>> +		switch (instr->type) {
> >>>>>> +		case NAND_OP_CMD_INSTR:
> >>>>>> +			if (first_cmd) {
> >>>>>> +				cmd |= COMMAND_CLE;
> >>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
> >>>>>> +					       ctrl->regs + CMD_REG1);
> >>>>>> +			} else {
> >>>>>> +				cmd |= COMMAND_SEC_CMD;
> >>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
> >>>>>> +					       ctrl->regs + CMD_REG2);
> >>>>>> +			}
> >>>>>> +			first_cmd = false;
> >>>>>> +			break;
> >>>>>> +		case NAND_OP_ADDR_INSTR:
> >>>>>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
> >>>>>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
> >>>>>> +			addrs = &instr->ctx.addr.addrs[offset];
> >>>>>> +
> >>>>>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
> >>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >>>>>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
> >>>>>> +			naddrs -= i;
> >>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >>>>>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
> >>>>>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> >>>>>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
> >>>>>> +			break;
> >>>>>> +
> >>>>>> +		case NAND_OP_DATA_IN_INSTR:
> >>>>>> +			size = nand_subop_get_data_len(subop, op_id);
> >>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >>>>>> +
> >>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >>>>>> +				COMMAND_RX | COMMAND_A_VALID;
> >>>>>> +
> >>>>>> +			instr_data_in = instr;
> >>>>>> +			break;
> >>>>>> +
> >>>>>> +		case NAND_OP_DATA_OUT_INSTR:
> >>>>>> +			size = nand_subop_get_data_len(subop, op_id);
> >>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >>>>>> +
> >>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >>>>>> +				COMMAND_TX | COMMAND_A_VALID;
> >>>>>> +
> >>>>>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
> >>>>>> +			writel_relaxed(reg, ctrl->regs + RESP);
> >>>>>> +
> >>>>>> +			break;
> >>>>>> +		case NAND_OP_WAITRDY_INSTR:
> >>>>>> +			cmd |= COMMAND_RBSY_CHK;
> >>>>>> +			break;
> >>>>>> +
> >>>>>> +		}
> >>>>>> +	}
> >>>>>> +
> >>>>>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
> >>>>>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> >>>>>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> >>>>>> +					     msecs_to_jiffies(500));  
> >>>>>
> >>>>> It's not obvious to me whether _io_ variant is appropriate to use here, would
> >>>>> be nice if somebody could clarify that. Maybe block/ already does the IO
> >>>>> accounting itself and hence the IO time would be counted twice in that case.  
> >>>>
> >>>> Good that you bring this up.
> >>>>
> >>>> I don't think that there is any higher layer which could take care of
> >>>> accounting. Usually, with raw nand there is no block layer involved
> >>>> anyway.
> >>>>
> >>>> In a quick test it seems that only when using wait_for_completion_io I/O
> >>>> is properly accounted in the "wait" section of top.
> >>>>
> >>>> So far only a single driver (omap2) used the _io variant, but I think it
> >>>> is the right thing to do! After all, it is I/O...
> >>>>
> >>>> Boris or any other MTD maintainer, any comment on this?  
> >>>
> >>> Given this definition of io_schedule_timeout() [1] (which is used when
> >>> you call wait_for_completion_io_timeout()), I'd say it's not useful to
> >>> use the _io_ version, simply because MTD devs are not exposed as blk
> >>> devices, and thus don't need the blk_schedule_flush_plug() that is done
> >>> is io_schedule_prepare(). But that also means MTD I/Os are not
> >>> accounted as I/Os :-(.  
> >>
> >> Documentation of wait_for_completion_io says:
> >> "The caller is accounted as waiting for IO (which traditionally means
> >> blkio only)."
> >>
> >> Which sounds as if it using _io is only an accounting thing...  
> > 
> > Yes, you should only use it for waiting for IO off a system call
> > read path. So block IO, or file system IO. Don't use it for internal
> > IO that isn't related to that.  
> 
> I guess that would be the case here, since MTD page read/writes are
> typically file system IOs (e.g. UBIFS).
> 
> The problem is just that is not block related at all since it uses the
> MTD subsystem... And it seems that the _io variants besides accounting,
> also take a role in the block subsystems device plugging mechanism. What
> is unclear to me if using the _io variant from the MTD subsystem
> potentially disturbs the plugging mechanism...

How about doing that in 2 steps: first use the non-io version as other
drivers do, and, depending on how this discussion evolves, switch to
the _io_ version if it appears to be the right thing to do.

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12 20:20             ` Stefan Agner
  2018-06-12 21:20               ` Boris Brezillon
@ 2018-06-12 21:24               ` Jens Axboe
  2018-06-12 21:30                 ` Boris Brezillon
  1 sibling, 1 reply; 24+ messages in thread
From: Jens Axboe @ 2018-06-12 21:24 UTC (permalink / raw)
  To: Stefan Agner
  Cc: Boris Brezillon, Dmitry Osipenko, dwmw2, computersforpeace,
	marek.vasut, robh+dt, mark.rutland, thierry.reding, dev,
	miquel.raynal, richard, marcel, krzk, benjamin.lindqvist,
	jonathanh, pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel

On 6/12/18 2:20 PM, Stefan Agner wrote:
> On 12.06.2018 17:24, Jens Axboe wrote:
>> On 6/12/18 3:17 AM, Stefan Agner wrote:
>>> [also added Jens Axboe]
>>>
>>> On 12.06.2018 10:27, Boris Brezillon wrote:
>>>> On Tue, 12 Jun 2018 10:06:42 +0200
>>>> Stefan Agner <stefan@agner.ch> wrote:
>>>>
>>>>> On 12.06.2018 02:03, Dmitry Osipenko wrote:
>>>>>> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>>>>>>> Add support for the NAND flash controller found on NVIDIA
>>>>>>> Tegra 2 SoCs. This implementation does not make use of the
>>>>>>> command queue feature. Regular operations/data transfers are
>>>>>>> done in PIO mode. Page read/writes with hardware ECC make
>>>>>>> use of the DMA for data transfer.
>>>>>>>
>>>>>>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>>>>>>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>>>>>>> ---
>>>>>>>  MAINTAINERS                       |    7 +
>>>>>>>  drivers/mtd/nand/raw/Kconfig      |    6 +
>>>>>>>  drivers/mtd/nand/raw/Makefile     |    1 +
>>>>>>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>>>>>>>  4 files changed, 1262 insertions(+)
>>>>>>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>>>>>>>
>>>>> [snip]
>>>>>>> +static int tegra_nand_cmd(struct nand_chip *chip,
>>>>>>> +			 const struct nand_subop *subop)
>>>>>>> +{
>>>>>>> +	const struct nand_op_instr *instr;
>>>>>>> +	const struct nand_op_instr *instr_data_in = NULL;
>>>>>>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>>>>>>> +	unsigned int op_id, size = 0, offset = 0;
>>>>>>> +	bool first_cmd = true;
>>>>>>> +	u32 reg, cmd = 0;
>>>>>>> +	int ret;
>>>>>>> +
>>>>>>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>>>>>>> +		unsigned int naddrs, i;
>>>>>>> +		const u8 *addrs;
>>>>>>> +		u32 addr1 = 0, addr2 = 0;
>>>>>>> +
>>>>>>> +		instr = &subop->instrs[op_id];
>>>>>>> +
>>>>>>> +		switch (instr->type) {
>>>>>>> +		case NAND_OP_CMD_INSTR:
>>>>>>> +			if (first_cmd) {
>>>>>>> +				cmd |= COMMAND_CLE;
>>>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
>>>>>>> +					       ctrl->regs + CMD_REG1);
>>>>>>> +			} else {
>>>>>>> +				cmd |= COMMAND_SEC_CMD;
>>>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
>>>>>>> +					       ctrl->regs + CMD_REG2);
>>>>>>> +			}
>>>>>>> +			first_cmd = false;
>>>>>>> +			break;
>>>>>>> +		case NAND_OP_ADDR_INSTR:
>>>>>>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
>>>>>>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>>>>>>> +			addrs = &instr->ctx.addr.addrs[offset];
>>>>>>> +
>>>>>>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>>>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>>>>>>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>>>>>>> +			naddrs -= i;
>>>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>>>>>>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>>>>>>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>>>>>>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>>>>>>> +			break;
>>>>>>> +
>>>>>>> +		case NAND_OP_DATA_IN_INSTR:
>>>>>>> +			size = nand_subop_get_data_len(subop, op_id);
>>>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>>>>>>> +
>>>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>>>>>>> +				COMMAND_RX | COMMAND_A_VALID;
>>>>>>> +
>>>>>>> +			instr_data_in = instr;
>>>>>>> +			break;
>>>>>>> +
>>>>>>> +		case NAND_OP_DATA_OUT_INSTR:
>>>>>>> +			size = nand_subop_get_data_len(subop, op_id);
>>>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
>>>>>>> +
>>>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>>>>>>> +				COMMAND_TX | COMMAND_A_VALID;
>>>>>>> +
>>>>>>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
>>>>>>> +			writel_relaxed(reg, ctrl->regs + RESP);
>>>>>>> +
>>>>>>> +			break;
>>>>>>> +		case NAND_OP_WAITRDY_INSTR:
>>>>>>> +			cmd |= COMMAND_RBSY_CHK;
>>>>>>> +			break;
>>>>>>> +
>>>>>>> +		}
>>>>>>> +	}
>>>>>>> +
>>>>>>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>>>>>>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
>>>>>>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>>>>>>> +					     msecs_to_jiffies(500));
>>>>>>
>>>>>> It's not obvious to me whether _io_ variant is appropriate to use here, would
>>>>>> be nice if somebody could clarify that. Maybe block/ already does the IO
>>>>>> accounting itself and hence the IO time would be counted twice in that case.
>>>>>
>>>>> Good that you bring this up.
>>>>>
>>>>> I don't think that there is any higher layer which could take care of
>>>>> accounting. Usually, with raw nand there is no block layer involved
>>>>> anyway.
>>>>>
>>>>> In a quick test it seems that only when using wait_for_completion_io I/O
>>>>> is properly accounted in the "wait" section of top.
>>>>>
>>>>> So far only a single driver (omap2) used the _io variant, but I think it
>>>>> is the right thing to do! After all, it is I/O...
>>>>>
>>>>> Boris or any other MTD maintainer, any comment on this?
>>>>
>>>> Given this definition of io_schedule_timeout() [1] (which is used when
>>>> you call wait_for_completion_io_timeout()), I'd say it's not useful to
>>>> use the _io_ version, simply because MTD devs are not exposed as blk
>>>> devices, and thus don't need the blk_schedule_flush_plug() that is done
>>>> is io_schedule_prepare(). But that also means MTD I/Os are not
>>>> accounted as I/Os :-(.
>>>
>>> Documentation of wait_for_completion_io says:
>>> "The caller is accounted as waiting for IO (which traditionally means
>>> blkio only)."
>>>
>>> Which sounds as if it using _io is only an accounting thing...
>>
>> Yes, you should only use it for waiting for IO off a system call
>> read path. So block IO, or file system IO. Don't use it for internal
>> IO that isn't related to that.
> 
> I guess that would be the case here, since MTD page read/writes are
> typically file system IOs (e.g. UBIFS).
> 
> The problem is just that is not block related at all since it uses the
> MTD subsystem... And it seems that the _io variants besides accounting,
> also take a role in the block subsystems device plugging mechanism. What
> is unclear to me if using the _io variant from the MTD subsystem
> potentially disturbs the plugging mechanism...

No, it has nothing to do with plugging at the block level. So if you're
doing regular user IO, then you should use the _io variants.

-- 
Jens Axboe


^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12 21:24               ` Jens Axboe
@ 2018-06-12 21:30                 ` Boris Brezillon
  0 siblings, 0 replies; 24+ messages in thread
From: Boris Brezillon @ 2018-06-12 21:30 UTC (permalink / raw)
  To: Jens Axboe
  Cc: Stefan Agner, Dmitry Osipenko, dwmw2, computersforpeace,
	marek.vasut, robh+dt, mark.rutland, thierry.reding, dev,
	miquel.raynal, richard, marcel, krzk, benjamin.lindqvist,
	jonathanh, pdeschrijver, pgaikwad, mirza.krak, gaireg, linux-mtd,
	linux-tegra, devicetree, linux-kernel

On Tue, 12 Jun 2018 15:24:41 -0600
Jens Axboe <axboe@kernel.dk> wrote:

> On 6/12/18 2:20 PM, Stefan Agner wrote:
> > On 12.06.2018 17:24, Jens Axboe wrote:  
> >> On 6/12/18 3:17 AM, Stefan Agner wrote:  
> >>> [also added Jens Axboe]
> >>>
> >>> On 12.06.2018 10:27, Boris Brezillon wrote:  
> >>>> On Tue, 12 Jun 2018 10:06:42 +0200
> >>>> Stefan Agner <stefan@agner.ch> wrote:
> >>>>  
> >>>>> On 12.06.2018 02:03, Dmitry Osipenko wrote:  
> >>>>>> On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:  
> >>>>>>> Add support for the NAND flash controller found on NVIDIA
> >>>>>>> Tegra 2 SoCs. This implementation does not make use of the
> >>>>>>> command queue feature. Regular operations/data transfers are
> >>>>>>> done in PIO mode. Page read/writes with hardware ECC make
> >>>>>>> use of the DMA for data transfer.
> >>>>>>>
> >>>>>>> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> >>>>>>> Signed-off-by: Stefan Agner <stefan@agner.ch>
> >>>>>>> ---
> >>>>>>>  MAINTAINERS                       |    7 +
> >>>>>>>  drivers/mtd/nand/raw/Kconfig      |    6 +
> >>>>>>>  drivers/mtd/nand/raw/Makefile     |    1 +
> >>>>>>>  drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
> >>>>>>>  4 files changed, 1262 insertions(+)
> >>>>>>>  create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
> >>>>>>>  
> >>>>> [snip]  
> >>>>>>> +static int tegra_nand_cmd(struct nand_chip *chip,
> >>>>>>> +			 const struct nand_subop *subop)
> >>>>>>> +{
> >>>>>>> +	const struct nand_op_instr *instr;
> >>>>>>> +	const struct nand_op_instr *instr_data_in = NULL;
> >>>>>>> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
> >>>>>>> +	unsigned int op_id, size = 0, offset = 0;
> >>>>>>> +	bool first_cmd = true;
> >>>>>>> +	u32 reg, cmd = 0;
> >>>>>>> +	int ret;
> >>>>>>> +
> >>>>>>> +	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
> >>>>>>> +		unsigned int naddrs, i;
> >>>>>>> +		const u8 *addrs;
> >>>>>>> +		u32 addr1 = 0, addr2 = 0;
> >>>>>>> +
> >>>>>>> +		instr = &subop->instrs[op_id];
> >>>>>>> +
> >>>>>>> +		switch (instr->type) {
> >>>>>>> +		case NAND_OP_CMD_INSTR:
> >>>>>>> +			if (first_cmd) {
> >>>>>>> +				cmd |= COMMAND_CLE;
> >>>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
> >>>>>>> +					       ctrl->regs + CMD_REG1);
> >>>>>>> +			} else {
> >>>>>>> +				cmd |= COMMAND_SEC_CMD;
> >>>>>>> +				writel_relaxed(instr->ctx.cmd.opcode,
> >>>>>>> +					       ctrl->regs + CMD_REG2);
> >>>>>>> +			}
> >>>>>>> +			first_cmd = false;
> >>>>>>> +			break;
> >>>>>>> +		case NAND_OP_ADDR_INSTR:
> >>>>>>> +			offset = nand_subop_get_addr_start_off(subop, op_id);
> >>>>>>> +			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
> >>>>>>> +			addrs = &instr->ctx.addr.addrs[offset];
> >>>>>>> +
> >>>>>>> +			cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
> >>>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >>>>>>> +				addr1 |= *addrs++ << (BITS_PER_BYTE * i);
> >>>>>>> +			naddrs -= i;
> >>>>>>> +			for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
> >>>>>>> +				addr2 |= *addrs++ << (BITS_PER_BYTE * i);
> >>>>>>> +			writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
> >>>>>>> +			writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
> >>>>>>> +			break;
> >>>>>>> +
> >>>>>>> +		case NAND_OP_DATA_IN_INSTR:
> >>>>>>> +			size = nand_subop_get_data_len(subop, op_id);
> >>>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >>>>>>> +
> >>>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >>>>>>> +				COMMAND_RX | COMMAND_A_VALID;
> >>>>>>> +
> >>>>>>> +			instr_data_in = instr;
> >>>>>>> +			break;
> >>>>>>> +
> >>>>>>> +		case NAND_OP_DATA_OUT_INSTR:
> >>>>>>> +			size = nand_subop_get_data_len(subop, op_id);
> >>>>>>> +			offset = nand_subop_get_data_start_off(subop, op_id);
> >>>>>>> +
> >>>>>>> +			cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
> >>>>>>> +				COMMAND_TX | COMMAND_A_VALID;
> >>>>>>> +
> >>>>>>> +			memcpy(&reg, instr->ctx.data.buf.out + offset, size);
> >>>>>>> +			writel_relaxed(reg, ctrl->regs + RESP);
> >>>>>>> +
> >>>>>>> +			break;
> >>>>>>> +		case NAND_OP_WAITRDY_INSTR:
> >>>>>>> +			cmd |= COMMAND_RBSY_CHK;
> >>>>>>> +			break;
> >>>>>>> +
> >>>>>>> +		}
> >>>>>>> +	}
> >>>>>>> +
> >>>>>>> +	cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
> >>>>>>> +	writel_relaxed(cmd, ctrl->regs + COMMAND);
> >>>>>>> +	ret = wait_for_completion_io_timeout(&ctrl->command_complete,
> >>>>>>> +					     msecs_to_jiffies(500));  
> >>>>>>
> >>>>>> It's not obvious to me whether _io_ variant is appropriate to use here, would
> >>>>>> be nice if somebody could clarify that. Maybe block/ already does the IO
> >>>>>> accounting itself and hence the IO time would be counted twice in that case.  
> >>>>>
> >>>>> Good that you bring this up.
> >>>>>
> >>>>> I don't think that there is any higher layer which could take care of
> >>>>> accounting. Usually, with raw nand there is no block layer involved
> >>>>> anyway.
> >>>>>
> >>>>> In a quick test it seems that only when using wait_for_completion_io I/O
> >>>>> is properly accounted in the "wait" section of top.
> >>>>>
> >>>>> So far only a single driver (omap2) used the _io variant, but I think it
> >>>>> is the right thing to do! After all, it is I/O...
> >>>>>
> >>>>> Boris or any other MTD maintainer, any comment on this?  
> >>>>
> >>>> Given this definition of io_schedule_timeout() [1] (which is used when
> >>>> you call wait_for_completion_io_timeout()), I'd say it's not useful to
> >>>> use the _io_ version, simply because MTD devs are not exposed as blk
> >>>> devices, and thus don't need the blk_schedule_flush_plug() that is done
> >>>> is io_schedule_prepare(). But that also means MTD I/Os are not
> >>>> accounted as I/Os :-(.  
> >>>
> >>> Documentation of wait_for_completion_io says:
> >>> "The caller is accounted as waiting for IO (which traditionally means
> >>> blkio only)."
> >>>
> >>> Which sounds as if it using _io is only an accounting thing...  
> >>
> >> Yes, you should only use it for waiting for IO off a system call
> >> read path. So block IO, or file system IO. Don't use it for internal
> >> IO that isn't related to that.  
> > 
> > I guess that would be the case here, since MTD page read/writes are
> > typically file system IOs (e.g. UBIFS).
> > 
> > The problem is just that is not block related at all since it uses the
> > MTD subsystem... And it seems that the _io variants besides accounting,
> > also take a role in the block subsystems device plugging mechanism. What
> > is unclear to me if using the _io variant from the MTD subsystem
> > potentially disturbs the plugging mechanism...  
> 
> No, it has nothing to do with plugging at the block level. So if you're
> doing regular user IO, then you should use the _io variants.

It's a bit more complicated than that. ->exec_op() is not only used for
read/write accesses, but also all kind of management around the NAND
chip which can't really be considered as storage device I/Os (at least
that's my opinion). The one in tegra_nand_page_xfer() is probably
valid though.


^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
  2018-06-12  8:13       ` Boris Brezillon
@ 2018-06-17 16:57         ` Stefan Agner
  0 siblings, 0 replies; 24+ messages in thread
From: Stefan Agner @ 2018-06-17 16:57 UTC (permalink / raw)
  To: Boris Brezillon
  Cc: Dmitry Osipenko, dwmw2, computersforpeace, marek.vasut, robh+dt,
	mark.rutland, thierry.reding, dev, miquel.raynal, richard,
	marcel, krzk, benjamin.lindqvist, jonathanh, pdeschrijver,
	pgaikwad, mirza.krak, gaireg, linux-mtd, linux-tegra, devicetree,
	linux-kernel

On 12.06.2018 10:13, Boris Brezillon wrote:
> On Tue, 12 Jun 2018 10:02:12 +0200
> Stefan Agner <stefan@agner.ch> wrote:
> 
>> >> +static int tegra_nand_read_page_hwecc(struct mtd_info *mtd,
>> >> +				      struct nand_chip *chip,
>> >> +				      uint8_t *buf, int oob_required, int page)
>> >> +{
>> >> +	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> >> +	struct tegra_nand_chip *nand = to_tegra_chip(chip);
>> >> +	void *oob_buf = oob_required ? chip->oob_poi : 0;
>> >> +	u32 dec_stat, max_corr_cnt;
>> >> +	unsigned long fail_sec_flag;
>> >> +	int ret;
>> >> +
>> >> +	tegra_nand_hw_ecc(ctrl, chip, true);
>> >> +	ret = tegra_nand_page_xfer(mtd, chip, buf, oob_buf, nand->tag.length,
>> >> +				   page, true);
>> >> +	tegra_nand_hw_ecc(ctrl, chip, false);
>> >> +	if (ret)
>> >> +		return ret;
>> >> +
>> >> +	/* No correctable or un-correctable errors, page must have 0 bitflips */
>> >> +	if (!ctrl->last_read_error)
>> >> +		return 0;
>> >> +
>> >> +	/*
>> >> +	 * Correctable or un-correctable errors occurred. Use DEC_STAT_BUF
>> >> +	 * which contains information for all ECC selections.
>> >> +	 *
>> >> +	 * Note that since we do not use Command Queues DEC_RESULT does not
>> >> +	 * state the number of pages we can read from the DEC_STAT_BUF. But
>> >> +	 * since CORRFAIL_ERR did occur during page read we do have a valid
>> >> +	 * result in DEC_STAT_BUF.
>> >> +	 */
>> >> +	ctrl->last_read_error = false;
>> >> +	dec_stat = readl_relaxed(ctrl->regs + DEC_STAT_BUF);
>> >> +
>> >> +	fail_sec_flag = (dec_stat & DEC_STAT_BUF_FAIL_SEC_FLAG_MASK) >>
>> >> +			DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT;
>> >> +
>> >> +	max_corr_cnt = (dec_stat & DEC_STAT_BUF_MAX_CORR_CNT_MASK) >>
>> >> +		       DEC_STAT_BUF_MAX_CORR_CNT_SHIFT;
>> >> +
>> >> +	if (fail_sec_flag) {
>> >> +		int bit, max_bitflips = 0;
>> >> +
>> >> +		/*
>> >> +		 * Check if all sectors in a page failed. If only some failed
>> >> +		 * its definitly not an erased page and we can return error
>> >> +		 * stats right away.
>> >> +		 *
>> >> +		 * E.g. controller might return fail_sec_flag with 0x4, which
>> >> +		 * would mean only the third sector failed to correct.
> 
> That works because you have NAND_NO_SUBPAGE_WRITE set (i.e. no partial
> page programming), probably something you should state here.
> 

Ok, will add a note.

>> >> +		 */
>> >> +		if (fail_sec_flag ^ GENMASK(chip->ecc.steps - 1, 0)) {
>> >> +			mtd->ecc_stats.failed += hweight8(fail_sec_flag);
>> >> +			return max_corr_cnt;
>> >> +		}
>> >> +
>> >> +		/*
>> >> +		 * All sectors failed to correct, but the ECC isn't smart
>> >> +		 * enough to figure out if a page is really completely erased.
>> >> +		 * We check the read data here to figure out if it's a
>> >> +		 * legitimate ECC error or only an erased page.
>> >> +		 */
>> >> +		for_each_set_bit(bit, &fail_sec_flag, chip->ecc.steps) {
>> >> +			u8 *data = buf + (chip->ecc.size * bit);
>> >> +
>> >> +			ret = nand_check_erased_ecc_chunk(data, chip->ecc.size,
>> >> +							  NULL, 0,
> 
> You should also check that the ECC bytes are 0xff here, otherwise you
> won't detect corruption of pages almost filled 0xff but with a few bits
> set to 0.
> 
> When you use nand_check_erased_ecc_chunk(), it's important to always
> pass the data along with its associated ECC bytes.
> 

Hm, I see this is important in case bitflips accumulate in OOB area
only.

>> >> +							  NULL, 0,
> 
> If you support writing extra OOB bytes, you should also pass them here.
> 

I see. OOB bytes handled together with the last subpage.

>> >> +							  chip->ecc.strength);
>> >> +			if (ret < 0)
>> >> +				mtd->ecc_stats.failed++;
>> >> +			else
>> >> +				max_bitflips = max(ret, max_bitflips);

I guess I should also increment ecc_stats.corrected here.

Is it correct that I increment for every step?

So if I have an ECC strength of 16, an empty page could have 8 bitflips
in the first step, and 12 in the second, I would increment
mtd->ecc_stats.corrected by 20 but return 12 (maximum number of bitflips
per step)?

--
Stefan

>> >> +		}
>> >> +
>> >> +		return max_t(unsigned int, max_corr_cnt, max_bitflips);
>> >> +	} else {
>> >> +		int corr_sec_flag;
>> >> +
>> >> +		corr_sec_flag = (dec_stat & DEC_STAT_BUF_CORR_SEC_FLAG_MASK) >>
>> >> +				DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT;
>> >> +
>> >> +		/*
>> >> +		 * The value returned in the register is the maximum of
>> >> +		 * bitflips encountered in any of the ECC regions. As there is
>> >> +		 * no way to get the number of bitflips in a specific regions
>> >> +		 * we are not able to deliver correct stats but instead
>> >> +		 * overestimate the number of corrected bitflips by assuming
>> >> +		 * that all regions where errors have been corrected
>> >> +		 * encountered the maximum number of bitflips.
>> >> +		 */
>> >> +		mtd->ecc_stats.corrected += max_corr_cnt * hweight8(corr_sec_flag);
>> >> +
>> >> +		return max_corr_cnt;
>> >> +	}
>> >> +

^ permalink raw reply	[flat|nested] 24+ messages in thread

end of thread, other threads:[~2018-06-17 16:57 UTC | newest]

Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
2018-06-11 20:52 ` [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm Stefan Agner
2018-06-12 18:37   ` Rob Herring
2018-06-11 20:52 ` [PATCH v4 2/6] mtd: rawnand: add an option to specify NAND chip as a boot device Stefan Agner
2018-06-11 20:52 ` [PATCH v4 3/6] mtd: rawnand: tegra: add devicetree binding Stefan Agner
2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
2018-06-11 23:08   ` kbuild test robot
2018-06-11 23:32   ` Dmitry Osipenko
2018-06-12  8:02     ` Stefan Agner
2018-06-12  8:13       ` Boris Brezillon
2018-06-17 16:57         ` Stefan Agner
2018-06-12  0:03   ` Dmitry Osipenko
2018-06-12  8:06     ` Stefan Agner
2018-06-12  8:27       ` Boris Brezillon
2018-06-12  9:17         ` Stefan Agner
2018-06-12  9:34           ` Boris Brezillon
2018-06-12 15:24           ` Jens Axboe
2018-06-12 20:20             ` Stefan Agner
2018-06-12 21:20               ` Boris Brezillon
2018-06-12 21:24               ` Jens Axboe
2018-06-12 21:30                 ` Boris Brezillon
2018-06-12 12:17   ` Dmitry Osipenko
2018-06-11 20:52 ` [PATCH v4 5/6] ARM: dts: tegra: add Tegra20 NAND flash controller node Stefan Agner
2018-06-11 20:52 ` [PATCH v4 6/6] ARM: dts: tegra: enable NAND flash on Colibri T20 Stefan Agner

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).