LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To: linux-amlogic@lists.infradead.org, khilman@baylibre.com
Cc: linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, hexdump0815@googlemail.com,
	Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Subject: [PATCH 1/1] ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805
Date: Fri, 24 May 2019 20:19:36 +0200	[thread overview]
Message-ID: <20190524181936.29470-2-martin.blumenstingl@googlemail.com> (raw)
In-Reply-To: <20190524181936.29470-1-martin.blumenstingl@googlemail.com>

The TRONFY MXQ comes with either 1GB or 2GB RAM.

Both variants share (like most boards based on Amlogic reference
designs):
- 10/100 PHY (IC Plus IP101GR) with GPIOH_4 being the reset line and
  GPIOH_3 the interrupt line
- SD card slot with the card detection GPIO at CARD_6
- VCCK is generated by PWM_C with a period of 1148ns and XTAL as input
  clock
- USB OTG exposed on one of the USB-A connectors
- 4-port USB hub with 3 ports exposed to the outside

There seem the multiple board revision out there according to various
forum posts:
- storage: eMMC or NAND flash
- wifi: Ampak AP6210 or Realtek 8189

Add support for the following functionality:
- SoC temperature (hwmon)
- changing the CPU voltage
- Ethernet connectivity
- SD card
- USB

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 arch/arm/boot/dts/meson8b-mxq.dts | 139 ++++++++++++++++++++++++++++++
 1 file changed, 139 insertions(+)

diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/meson8b-mxq.dts
index 08ddd7fb0bf8..07f1cc513f8a 100644
--- a/arch/arm/boot/dts/meson8b-mxq.dts
+++ b/arch/arm/boot/dts/meson8b-mxq.dts
@@ -45,6 +45,9 @@
  */
 
 /dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
 #include "meson8b.dtsi"
 
 / {
@@ -63,6 +66,126 @@
 		device_type = "memory";
 		reg = <0x40000000 0x40000000>;
 	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&saradc 8>;
+	};
+
+	vcck: regulator-vcck {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VCCK";
+		regulator-min-microvolt = <860000>;
+		regulator-max-microvolt = <1140000>;
+
+		pwms = <&pwm_cd 0 1148 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc_3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&vcc_5v>;
+	};
+
+	vcc_5v: regulator-vcc5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vcck>;
+};
+
+&ethmac {
+	status = "okay";
+
+	pinctrl-0 = <&eth_rmii_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	snps,reset-gpio = <&gpio GPIOH_4 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* IC Plus IP101A/G (0x02430c54) */
+			reg = <0>;
+			icplus,select-interrupt;
+			interrupt-parent = <&gpio_intc>;
+			/* GPIOH_3 */
+			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vcc_1v8>;
+};
+
+&sdio {
+	status = "okay";
+
+	pinctrl-0 = <&sd_b_pins>;
+	pinctrl-names = "default";
+
+	/* SD card */
+	sd_card_slot: slot@1 {
+		compatible = "mmc-slot";
+		reg = <1>;
+		status = "okay";
+
+		bus-width = <4>;
+		no-sdio;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
+		disable-wp;
+
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+		vmmc-supply = <&vcc_3v3>;
+	};
+};
+
+&pwm_cd {
+	status = "okay";
+	pinctrl-0 = <&pwm_c1_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_XTAL>;
+	clock-names = "clkin0";
 };
 
 &uart_AO {
@@ -70,3 +193,19 @@
 	pinctrl-0 = <&uart_ao_a_pins>;
 	pinctrl-names = "default";
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
-- 
2.21.0


  reply	other threads:[~2019-05-24 18:19 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-24 18:19 [PATCH 0/1] ARM: meson8b-mxq: better support for the TRONFY MXQ Martin Blumenstingl
2019-05-24 18:19 ` Martin Blumenstingl [this message]
2019-05-27 13:17   ` [PATCH 1/1] ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805 hex dump
     [not found]   ` <CAKTihDVyQqq82KKofCTKoUYJOyT6T738uq_A=kiEqahDx9YQfA@mail.gmail.com>
2019-06-03 22:18     ` Kevin Hilman
2019-05-24 19:42 ` [PATCH 0/1] ARM: meson8b-mxq: better support for the TRONFY MXQ Kevin Hilman
2019-05-24 19:52   ` Martin Blumenstingl

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190524181936.29470-2-martin.blumenstingl@googlemail.com \
    --to=martin.blumenstingl@googlemail.com \
    --cc=hexdump0815@googlemail.com \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --subject='Re: [PATCH 1/1] ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).