LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* [PATCH v4 0/3] arm64: Add initial support for Odroid-N2
@ 2019-05-27 14:02 Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 1/3] dt-bindings: arm: amlogic: add G12B bindings Neil Armstrong
                   ` (2 more replies)
  0 siblings, 3 replies; 8+ messages in thread
From: Neil Armstrong @ 2019-05-27 14:02 UTC (permalink / raw)
  To: khilman; +Cc: Neil Armstrong, linux-amlogic, linux-arm-kernel, linux-kernel

This patchset adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC

The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
  compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same

Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.

Dependencies :
- Patch 1, 2 : YAML rewrite of amlogic.txt bindings at [7]
- Patch 3 : None since clock + g12b bindings has been acked

Changes since v3 at [8]:
- Dropped arm,armv8
- Dropped eee disable, not needed in further tests
- Add comments about where are connected the regulators pins
- Moved the phy0 regulator to the usb vbus regulator

Changes since v2 at [5]:
- sent the clk patches in standalone at [6]
- rewrote the bindings on top of the YAML rewrite at [7]
- Added MMC, SDCard and Network support to Odroid-N2

Changes since v1 at [3]:
- Renamed the g12b cpu clocks like g12a counterparts
- Rebased clock patches on top of Guillaume's Temperature sensor Clock patches at [4]
- Added AO-CEC-B support to N2 DTS

Changes since RFC at [1]:
- Added bindings review tags
- Moved the fclk_div3 CRITICAL flags to the gate
- Removed invalid CRITICAL flags on the cpu clocks

[1] https://lkml.kernel.org/r/20190327103308.25058-1-narmstrong@baylibre.com
[2] https://lkml.kernel.org/r/20190325145914.32391-1-narmstrong@baylibre.com
[3] https://lkml.kernel.org/r/20190404150518.30337-1-narmstrong@baylibre.com
[4] https://lkml.kernel.org/r/20190412100221.26740-1-glaroque@baylibre.com
[5] https://lkml.kernel.org/r/20190423091503.10847-1-narmstrong@baylibre.com
[6] https://lkml.kernel.org/r/20190521150130.31684-1-narmstrong@baylibre.com
[7] https://lkml.kernel.org/r/20190517152723.28518-2-robh@kernel.org
[8] https://lkml.kernel.org/r/20190521151952.2779-1-narmstrong@baylibre.com

Neil Armstrong (3):
  dt-bindings: arm: amlogic: add G12B bindings
  dt-bindings: arm: amlogic: add Odroid-N2 binding
  arm64: dts: meson: Add minimal support for Odroid-N2

 .../devicetree/bindings/arm/amlogic.yaml      |   6 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 288 ++++++++++++++++++
 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi   |  82 +++++
 4 files changed, 377 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi

-- 
2.21.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v4 1/3] dt-bindings: arm: amlogic: add G12B bindings
  2019-05-27 14:02 [PATCH v4 0/3] arm64: Add initial support for Odroid-N2 Neil Armstrong
@ 2019-05-27 14:02 ` Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 2/3] dt-bindings: arm: amlogic: add Odroid-N2 binding Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2 Neil Armstrong
  2 siblings, 0 replies; 8+ messages in thread
From: Neil Armstrong @ 2019-05-27 14:02 UTC (permalink / raw)
  To: khilman, devicetree
  Cc: Neil Armstrong, linux-amlogic, linux-arm-kernel, linux-kernel,
	Rob Herring, Martin Blumenstingl

Add compatible for the Amlogic G12B SoC, sharing most of the
features and architecture with the G12A SoC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 6d5bb493db03..28115dd49f96 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -137,4 +137,8 @@ properties:
               - amlogic,u200
           - const: amlogic,g12a
 
+      - description: Boards with the Amlogic Meson G12B S922X SoC
+        items:
+          - const: amlogic,g12b
+
 ...
-- 
2.21.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v4 2/3] dt-bindings: arm: amlogic: add Odroid-N2 binding
  2019-05-27 14:02 [PATCH v4 0/3] arm64: Add initial support for Odroid-N2 Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 1/3] dt-bindings: arm: amlogic: add G12B bindings Neil Armstrong
@ 2019-05-27 14:02 ` Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2 Neil Armstrong
  2 siblings, 0 replies; 8+ messages in thread
From: Neil Armstrong @ 2019-05-27 14:02 UTC (permalink / raw)
  To: khilman, devicetree
  Cc: Neil Armstrong, linux-amlogic, linux-arm-kernel, linux-kernel,
	Rob Herring, Martin Blumenstingl

Add compatible for the Amlogic G12B (S922X) SoC based Odroid-N2 SBC
from HardKernel.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 28115dd49f96..f75df4471c0a 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -139,6 +139,8 @@ properties:
 
       - description: Boards with the Amlogic Meson G12B S922X SoC
         items:
+          - enum:
+              - hardkernel,odroid-n2
           - const: amlogic,g12b
 
 ...
-- 
2.21.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
  2019-05-27 14:02 [PATCH v4 0/3] arm64: Add initial support for Odroid-N2 Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 1/3] dt-bindings: arm: amlogic: add G12B bindings Neil Armstrong
  2019-05-27 14:02 ` [PATCH v4 2/3] dt-bindings: arm: amlogic: add Odroid-N2 binding Neil Armstrong
@ 2019-05-27 14:02 ` Neil Armstrong
  2019-05-27 18:12   ` Martin Blumenstingl
  2019-05-29 10:08   ` Neil Armstrong
  2 siblings, 2 replies; 8+ messages in thread
From: Neil Armstrong @ 2019-05-27 14:02 UTC (permalink / raw)
  To: khilman; +Cc: Neil Armstrong, linux-amlogic, linux-arm-kernel, linux-kernel

This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC

The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
  compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same

Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 288 ++++++++++++++++++
 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi   |  82 +++++
 3 files changed, 371 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e129c03ced14..07b861fe5fa5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
new file mode 100644
index 000000000000..48783ead8dfb
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+	model = "Hardkernel ODROID-N2";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "n2:blue";
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0
+			  1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	hub_5v: regulator-hub_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "HUB_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the Hub CHIPENABLE, LOW sets low power state */
+		gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&hub_5v>;
+
+		/* Connected to the microUSB port power enable */
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */	
+		reg = <0>;
+		max-speed = <1000>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+};
+
+&gpio {
+	/*
+	 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+	 * to be turned high in order to be detected by the USB Controller
+	 * This signal should be handled by a USB specific power sequence
+	 * in order to reset the Hub when USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+	phy-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
new file mode 100644
index 000000000000..9e88e513b22d
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+	compatible = "amlogic,g12b";
+
+	cpus {
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu100>;
+				};
+
+				core1 {
+					cpu = <&cpu101>;
+				};
+
+				core2 {
+					cpu = <&cpu102>;
+				};
+
+				core3 {
+					cpu = <&cpu103>;
+				};
+			};
+		};
+
+		/delete-node/ cpu@2;
+		/delete-node/ cpu@3;
+
+		cpu100: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu101: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu102: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x102>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu103: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x103>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+	};
+};
+
+&clkc {
+	compatible = "amlogic,g12b-clkc";
+};
-- 
2.21.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
  2019-05-27 14:02 ` [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2 Neil Armstrong
@ 2019-05-27 18:12   ` Martin Blumenstingl
  2019-05-29 10:08   ` Neil Armstrong
  1 sibling, 0 replies; 8+ messages in thread
From: Martin Blumenstingl @ 2019-05-27 18:12 UTC (permalink / raw)
  To: Neil Armstrong; +Cc: khilman, linux-amlogic, linux-kernel, linux-arm-kernel

On Mon, May 27, 2019 at 4:03 PM Neil Armstrong <narmstrong@baylibre.com> wrote:
>
> This patch adds basic support for :
> - Amlogic G12B, which is very similar to G12A
> - The HardKernel Odroid-N2 based on the S922X SoC
>
> The Amlogic G12B SoC is very similar with the G12A SoC, sharing
> most of the features and architecture, but with these differences :
> - The first CPU cluster only has 2xCortex-A53 instead of 4
> - G12B has a second cluster of 4xCortex-A73
> - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
> - CPU Clock architecture is difference, thus needing a different
>   compatible to handle this slight difference
> - Supports a MIPI CSI input
> - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
>
> Actual support is done in the same way as for the GXM support, including
> the G12A dtsi and redefining the CPU clusters.
> Unlike GXM, the first cluster is different, thus needing to remove
> the last 2 cpu nodes of the first cluster.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
  2019-05-27 14:02 ` [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2 Neil Armstrong
  2019-05-27 18:12   ` Martin Blumenstingl
@ 2019-05-29 10:08   ` Neil Armstrong
  2019-05-29 18:13     ` Martin Blumenstingl
  1 sibling, 1 reply; 8+ messages in thread
From: Neil Armstrong @ 2019-05-29 10:08 UTC (permalink / raw)
  To: khilman; +Cc: linux-amlogic, linux-arm-kernel, linux-kernel

On 27/05/2019 16:02, Neil Armstrong wrote:
> This patch adds basic support for :
> - Amlogic G12B, which is very similar to G12A
> - The HardKernel Odroid-N2 based on the S922X SoC
> 
> The Amlogic G12B SoC is very similar with the G12A SoC, sharing
> most of the features and architecture, but with these differences :
> - The first CPU cluster only has 2xCortex-A53 instead of 4
> - G12B has a second cluster of 4xCortex-A73
> - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
> - CPU Clock architecture is difference, thus needing a different
>   compatible to handle this slight difference
> - Supports a MIPI CSI input
> - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
> 
> Actual support is done in the same way as for the GXM support, including
> the G12A dtsi and redefining the CPU clusters.
> Unlike GXM, the first cluster is different, thus needing to remove
> the last 2 cpu nodes of the first cluster.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>  .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 288 ++++++++++++++++++
>  arch/arm64/boot/dts/amlogic/meson-g12b.dtsi   |  82 +++++
>  3 files changed, 371 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index e129c03ced14..07b861fe5fa5 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
> new file mode 100644
> index 000000000000..48783ead8dfb
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
> @@ -0,0 +1,288 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +

[...]

> +
> +	hub_5v: regulator-hub_5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "HUB_5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v>;
> +
> +		/* Connected to the Hub CHIPENABLE, LOW sets low power state */
> +		gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	usb_pwr_en: regulator-usb_pwr_en {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB_PWR_EN";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&hub_5v>;
> +
> +		/* Connected to the microUSB port power enable */
> +		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +

[...]

> +
> +&usb {
> +	status = "okay";
> +	vbus-supply = <&usb_pwr_en>;
> +};
> +
> +&usb2_phy0 {
> +	phy-supply = <&vcc_5v>;
> +};
> +
> +&usb2_phy1 {
> +	phy-supply = <&vcc_5v>;
> +};

In fact, I need to fixup here :

usb2_phy1 needs &hub_5v and regulator-usb_pwr_en depends on &vcc_5v instead...

@Martin, can I still keep your reviewed-by for v5 ?

Neil

> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
> new file mode 100644
> index 000000000000..9e88e513b22d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
> @@ -0,0 +1,82 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)

[...]

> +		};
> +	};
> +};
> +
> +&clkc {
> +	compatible = "amlogic,g12b-clkc";
> +};
> 


^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
  2019-05-29 10:08   ` Neil Armstrong
@ 2019-05-29 18:13     ` Martin Blumenstingl
  2019-05-31  9:21       ` Neil Armstrong
  0 siblings, 1 reply; 8+ messages in thread
From: Martin Blumenstingl @ 2019-05-29 18:13 UTC (permalink / raw)
  To: Neil Armstrong; +Cc: khilman, linux-amlogic, linux-kernel, linux-arm-kernel

Hi Neil,

On Wed, May 29, 2019 at 12:09 PM Neil Armstrong <narmstrong@baylibre.com> wrote:
>
> On 27/05/2019 16:02, Neil Armstrong wrote:
> > This patch adds basic support for :
> > - Amlogic G12B, which is very similar to G12A
> > - The HardKernel Odroid-N2 based on the S922X SoC
> >
> > The Amlogic G12B SoC is very similar with the G12A SoC, sharing
> > most of the features and architecture, but with these differences :
> > - The first CPU cluster only has 2xCortex-A53 instead of 4
> > - G12B has a second cluster of 4xCortex-A73
> > - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
> > - CPU Clock architecture is difference, thus needing a different
> >   compatible to handle this slight difference
> > - Supports a MIPI CSI input
> > - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
> >
> > Actual support is done in the same way as for the GXM support, including
> > the G12A dtsi and redefining the CPU clusters.
> > Unlike GXM, the first cluster is different, thus needing to remove
> > the last 2 cpu nodes of the first cluster.
> >
> > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> > ---
> >  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
> >  .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 288 ++++++++++++++++++
> >  arch/arm64/boot/dts/amlogic/meson-g12b.dtsi   |  82 +++++
> >  3 files changed, 371 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
> >  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> > index e129c03ced14..07b861fe5fa5 100644
> > --- a/arch/arm64/boot/dts/amlogic/Makefile
> > +++ b/arch/arm64/boot/dts/amlogic/Makefile
> > @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> >  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> >  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
> >  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> > +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
> >  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
> >  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
> >  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
> > new file mode 100644
> > index 000000000000..48783ead8dfb
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
> > @@ -0,0 +1,288 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2019 BayLibre, SAS
> > + * Author: Neil Armstrong <narmstrong@baylibre.com>
> > + */
> > +
> > +/dts-v1/;
> > +
>
> [...]
>
> > +
> > +     hub_5v: regulator-hub_5v {
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "HUB_5V";
> > +             regulator-min-microvolt = <5000000>;
> > +             regulator-max-microvolt = <5000000>;
> > +             vin-supply = <&vcc_5v>;
> > +
> > +             /* Connected to the Hub CHIPENABLE, LOW sets low power state */
> > +             gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
> > +             enable-active-high;
> > +     };
> > +
> > +     usb_pwr_en: regulator-usb_pwr_en {
> > +             compatible = "regulator-fixed";
> > +             regulator-name = "USB_PWR_EN";
> > +             regulator-min-microvolt = <5000000>;
> > +             regulator-max-microvolt = <5000000>;
> > +             vin-supply = <&hub_5v>;
> > +
> > +             /* Connected to the microUSB port power enable */
> > +             gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
> > +             enable-active-high;
> > +     };
> > +
>
> [...]
>
> > +
> > +&usb {
> > +     status = "okay";
> > +     vbus-supply = <&usb_pwr_en>;
> > +};
> > +
> > +&usb2_phy0 {
> > +     phy-supply = <&vcc_5v>;
> > +};
> > +
> > +&usb2_phy1 {
> > +     phy-supply = <&vcc_5v>;
> > +};
>
> In fact, I need to fixup here :
>
> usb2_phy1 needs &hub_5v and regulator-usb_pwr_en depends on &vcc_5v instead...
sounds fine for me because I don't see a better way for now

> @Martin, can I still keep your reviewed-by for v5 ?
yes, you can keep it

when you re-send it: can you please add a comment to the phy-supply in
usb2_phy1?
I have this in mind: "enable the hub which is connected to this port"
(imho this is a valuable hint together with the "CHIPENABLE" comment
that you already have inside &hub_5v and it helps to make it easier to
understand without having to test it on physical hardware)


Martin

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
  2019-05-29 18:13     ` Martin Blumenstingl
@ 2019-05-31  9:21       ` Neil Armstrong
  0 siblings, 0 replies; 8+ messages in thread
From: Neil Armstrong @ 2019-05-31  9:21 UTC (permalink / raw)
  To: Martin Blumenstingl
  Cc: khilman, linux-amlogic, linux-kernel, linux-arm-kernel

On 29/05/2019 20:13, Martin Blumenstingl wrote:
> Hi Neil,
> 
> On Wed, May 29, 2019 at 12:09 PM Neil Armstrong <narmstrong@baylibre.com> wrote:
>>
>> On 27/05/2019 16:02, Neil Armstrong wrote:
>>> This patch adds basic support for :
>>> - Amlogic G12B, which is very similar to G12A
>>> - The HardKernel Odroid-N2 based on the S922X SoC
>>>
>>> The Amlogic G12B SoC is very similar with the G12A SoC, sharing
>>> most of the features and architecture, but with these differences :
>>> - The first CPU cluster only has 2xCortex-A53 instead of 4
>>> - G12B has a second cluster of 4xCortex-A73
>>> - Both cluster can achieve 2GHz instead of 1,8GHz for G12A
>>> - CPU Clock architecture is difference, thus needing a different
>>>   compatible to handle this slight difference
>>> - Supports a MIPI CSI input
>>> - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
>>>
>>> Actual support is done in the same way as for the GXM support, including
>>> the G12A dtsi and redefining the CPU clusters.
>>> Unlike GXM, the first cluster is different, thus needing to remove
>>> the last 2 cpu nodes of the first cluster.
>>>
>>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>>> ---
>>>  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>>>  .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 288 ++++++++++++++++++
>>>  arch/arm64/boot/dts/amlogic/meson-g12b.dtsi   |  82 +++++
>>>  3 files changed, 371 insertions(+)
>>>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
>>>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>>> index e129c03ced14..07b861fe5fa5 100644
>>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>>> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
>>>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
>>>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
>>>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
>>> +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
>>>  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
>>>  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
>>>  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
>>> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
>>> new file mode 100644
>>> index 000000000000..48783ead8dfb
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
>>> @@ -0,0 +1,288 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +/*
>>> + * Copyright (c) 2019 BayLibre, SAS
>>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>
>> [...]
>>
>>> +
>>> +     hub_5v: regulator-hub_5v {
>>> +             compatible = "regulator-fixed";
>>> +             regulator-name = "HUB_5V";
>>> +             regulator-min-microvolt = <5000000>;
>>> +             regulator-max-microvolt = <5000000>;
>>> +             vin-supply = <&vcc_5v>;
>>> +
>>> +             /* Connected to the Hub CHIPENABLE, LOW sets low power state */
>>> +             gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
>>> +             enable-active-high;
>>> +     };
>>> +
>>> +     usb_pwr_en: regulator-usb_pwr_en {
>>> +             compatible = "regulator-fixed";
>>> +             regulator-name = "USB_PWR_EN";
>>> +             regulator-min-microvolt = <5000000>;
>>> +             regulator-max-microvolt = <5000000>;
>>> +             vin-supply = <&hub_5v>;
>>> +
>>> +             /* Connected to the microUSB port power enable */
>>> +             gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
>>> +             enable-active-high;
>>> +     };
>>> +
>>
>> [...]
>>
>>> +
>>> +&usb {
>>> +     status = "okay";
>>> +     vbus-supply = <&usb_pwr_en>;
>>> +};
>>> +
>>> +&usb2_phy0 {
>>> +     phy-supply = <&vcc_5v>;
>>> +};
>>> +
>>> +&usb2_phy1 {
>>> +     phy-supply = <&vcc_5v>;
>>> +};
>>
>> In fact, I need to fixup here :
>>
>> usb2_phy1 needs &hub_5v and regulator-usb_pwr_en depends on &vcc_5v instead...
> sounds fine for me because I don't see a better way for now
> 
>> @Martin, can I still keep your reviewed-by for v5 ?
> yes, you can keep it
> 
> when you re-send it: can you please add a comment to the phy-supply in
> usb2_phy1?
> I have this in mind: "enable the hub which is connected to this port"
> (imho this is a valuable hint together with the "CHIPENABLE" comment
> that you already have inside &hub_5v and it helps to make it easier to
> understand without having to test it on physical hardware)

Sure, thanks !

Neil

> 
> 
> Martin
> 


^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2019-05-31  9:21 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-27 14:02 [PATCH v4 0/3] arm64: Add initial support for Odroid-N2 Neil Armstrong
2019-05-27 14:02 ` [PATCH v4 1/3] dt-bindings: arm: amlogic: add G12B bindings Neil Armstrong
2019-05-27 14:02 ` [PATCH v4 2/3] dt-bindings: arm: amlogic: add Odroid-N2 binding Neil Armstrong
2019-05-27 14:02 ` [PATCH v4 3/3] arm64: dts: meson: Add minimal support for Odroid-N2 Neil Armstrong
2019-05-27 18:12   ` Martin Blumenstingl
2019-05-29 10:08   ` Neil Armstrong
2019-05-29 18:13     ` Martin Blumenstingl
2019-05-31  9:21       ` Neil Armstrong

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).