LKML Archive on lore.kernel.org
 help / color / Atom feed
From: Jonathan Marek <jonathan@marek.ca>
To: linux-arm-msm@vger.kernel.org
Cc: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Vinod Koul <vkoul@kernel.org>,
	linux-kernel@vger.kernel.org (open list:GENERIC PHY FRAMEWORK)
Subject: [PATCH 1/3] phy: qcom-qmp: Allow different values for second lane
Date: Sat, 23 May 2020 22:14:13 -0400
Message-ID: <20200524021416.17049-2-jonathan@marek.ca> (raw)
In-Reply-To: <20200524021416.17049-1-jonathan@marek.ca>

The primary USB PHY on sm8250 sets some values differently for the second
lane. This makes it possible to represent that.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 52 ++++++++++++++++++++++-------
 1 file changed, 40 insertions(+), 12 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index e91040af3394..b3e07afca3ca 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -82,20 +82,34 @@ struct qmp_phy_init_tbl {
 	 * register part of layout ?
 	 * if yes, then offset gives index in the reg-layout
 	 */
-	int in_layout;
+	bool in_layout;
+	/*
+	 * mask of lanes for which this register is written
+	 * for cases when second lane needs different values
+	 */
+	u8 lane_mask;
 };
 
 #define QMP_PHY_INIT_CFG(o, v)		\
 	{				\
 		.offset = o,		\
 		.val = v,		\
+		.lane_mask = 0xff,	\
 	}
 
 #define QMP_PHY_INIT_CFG_L(o, v)	\
 	{				\
 		.offset = o,		\
 		.val = v,		\
-		.in_layout = 1,		\
+		.in_layout = true,	\
+		.lane_mask = 0xff,	\
+	}
+
+#define QMP_PHY_INIT_CFG_LANE(o, v, l)	\
+	{				\
+		.offset = o,		\
+		.val = v,		\
+		.lane_mask = l,		\
 	}
 
 /* set of registers with offsets different per-PHY */
@@ -1986,10 +2000,11 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 	.is_dual_lane_phy	= true,
 };
 
-static void qcom_qmp_phy_configure(void __iomem *base,
-				   const unsigned int *regs,
-				   const struct qmp_phy_init_tbl tbl[],
-				   int num)
+static void qcom_qmp_phy_configure_lane(void __iomem *base,
+					const unsigned int *regs,
+					const struct qmp_phy_init_tbl tbl[],
+					int num,
+					u8 lane_mask)
 {
 	int i;
 	const struct qmp_phy_init_tbl *t = tbl;
@@ -1998,6 +2013,9 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 		return;
 
 	for (i = 0; i < num; i++, t++) {
+		if (!(t->lane_mask & lane_mask))
+			continue;
+
 		if (t->in_layout)
 			writel(t->val, base + regs[t->offset]);
 		else
@@ -2005,6 +2023,14 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 	}
 }
 
+static void qcom_qmp_phy_configure(void __iomem *base,
+				   const unsigned int *regs,
+				   const struct qmp_phy_init_tbl tbl[],
+				   int num)
+{
+	qcom_qmp_phy_configure_lane(base, regs, tbl, num, 0xff);
+}
+
 static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 {
 	struct qcom_qmp *qmp = qphy->qmp;
@@ -2219,16 +2245,18 @@ static int qcom_qmp_phy_enable(struct phy *phy)
 	}
 
 	/* Tx, Rx, and PCS configurations */
-	qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+	qcom_qmp_phy_configure_lane(tx, cfg->regs,
+				    cfg->tx_tbl, cfg->tx_tbl_num, 1);
 	/* Configuration for other LANE for USB-DP combo PHY */
 	if (cfg->is_dual_lane_phy)
-		qcom_qmp_phy_configure(qphy->tx2, cfg->regs,
-				       cfg->tx_tbl, cfg->tx_tbl_num);
+		qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
+					    cfg->tx_tbl, cfg->tx_tbl_num, 2);
 
-	qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+	qcom_qmp_phy_configure_lane(rx, cfg->regs,
+				    cfg->rx_tbl, cfg->rx_tbl_num, 1);
 	if (cfg->is_dual_lane_phy)
-		qcom_qmp_phy_configure(qphy->rx2, cfg->regs,
-				       cfg->rx_tbl, cfg->rx_tbl_num);
+		qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
+					    cfg->rx_tbl, cfg->rx_tbl_num, 2);
 
 	qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 	ret = reset_control_deassert(qmp->ufs_reset);
-- 
2.26.1


  reply index

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-05-24  2:14 [PATCH 0/3] phy: qcom-qmp: add V4 USB PHYs Jonathan Marek
2020-05-24  2:14 ` Jonathan Marek [this message]
2020-06-25 19:41   ` [PATCH 1/3] phy: qcom-qmp: Allow different values for second lane Dmitry Baryshkov
2020-06-26  7:35   ` Bjorn Andersson
2020-05-24  2:14 ` [PATCH 2/3] phy: qcom-qmp: Add QMP V4 USB3 UNIPHY Jonathan Marek
2020-06-25 19:42   ` Dmitry Baryshkov
2020-06-26  7:37   ` Bjorn Andersson
2020-05-24  2:14 ` [PATCH 3/3] phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250 Jonathan Marek
2020-06-25 19:42   ` Dmitry Baryshkov
2020-06-26  7:40   ` Bjorn Andersson
2020-06-29  9:41 ` [PATCH 0/3] phy: qcom-qmp: add V4 USB PHYs Vinod Koul

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200524021416.17049-2-jonathan@marek.ca \
    --to=jonathan@marek.ca \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=kishon@ti.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

LKML Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lkml.kernel.org/lkml/0 lkml/git/0.git
	git clone --mirror https://lkml.kernel.org/lkml/1 lkml/git/1.git
	git clone --mirror https://lkml.kernel.org/lkml/2 lkml/git/2.git
	git clone --mirror https://lkml.kernel.org/lkml/3 lkml/git/3.git
	git clone --mirror https://lkml.kernel.org/lkml/4 lkml/git/4.git
	git clone --mirror https://lkml.kernel.org/lkml/5 lkml/git/5.git
	git clone --mirror https://lkml.kernel.org/lkml/6 lkml/git/6.git
	git clone --mirror https://lkml.kernel.org/lkml/7 lkml/git/7.git
	git clone --mirror https://lkml.kernel.org/lkml/8 lkml/git/8.git
	git clone --mirror https://lkml.kernel.org/lkml/9 lkml/git/9.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 lkml lkml/ https://lkml.kernel.org/lkml \
		linux-kernel@vger.kernel.org
	public-inbox-index lkml

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git