LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* [PATCH v34 0/3] Mainline imx6 based SKOV boards
@ 2021-08-04  4:34 Oleksij Rempel
  2021-08-04  4:34 ` [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S Oleksij Rempel
                   ` (3 more replies)
  0 siblings, 4 replies; 7+ messages in thread
From: Oleksij Rempel @ 2021-08-04  4:34 UTC (permalink / raw)
  To: Arnd Bergmann, Daniel Vetter, David Airlie, Olof Johansson,
	Rob Herring, Sascha Hauer, Shawn Guo, soc, Thierry Reding
  Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
	linux-kernel, Pengutronix Kernel Team, dri-devel, Sam Ravnborg

changes v4:
- add vref-supply to adc@0
- split gpio assignment for the mdio node

changes v3:
- drop panel bindings patches, it is already in drm-misc-next
- remove some new lines
- reorder compatibles at the start of the nodes
- use lowercase for hex value
- add enable-active-high to the regulator-vcc-mmc-io and fix MMC voltage
  configuration.

changes v2:
- remove unnecessary newlines.
- change linux,wakeup to wakeup-source
- change switch@3 unit-address to @0
- sort aliases alphabetically

Mainline imx6 based DTs for SKOV A/S boards

Oleksij Rempel (2):
  dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
  dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards

Sam Ravnborg (1):
  ARM: dts: add SKOV imx6q and imx6dl based boards

 .../devicetree/bindings/arm/fsl.yaml          |   5 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/boot/dts/Makefile                    |   5 +
 arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts    |  13 +
 arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts    | 106 ++++
 arch/arm/boot/dts/imx6q-skov-revc-lt2.dts     |  36 ++
 arch/arm/boot/dts/imx6q-skov-revc-lt6.dts     | 128 +++++
 .../dts/imx6q-skov-reve-mi1010ait-1cp1.dts    | 127 +++++
 arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi  |  54 ++
 arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi       | 477 ++++++++++++++++++
 10 files changed, 953 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts
 create mode 100644 arch/arm/boot/dts/imx6q-skov-revc-lt2.dts
 create mode 100644 arch/arm/boot/dts/imx6q-skov-revc-lt6.dts
 create mode 100644 arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
 create mode 100644 arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi

-- 
2.30.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
  2021-08-04  4:34 [PATCH v34 0/3] Mainline imx6 based SKOV boards Oleksij Rempel
@ 2021-08-04  4:34 ` Oleksij Rempel
  2021-08-11 18:40   ` Rob Herring
  2021-08-04  4:34 ` [PATCH v4 2/3] dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards Oleksij Rempel
                   ` (2 subsequent siblings)
  3 siblings, 1 reply; 7+ messages in thread
From: Oleksij Rempel @ 2021-08-04  4:34 UTC (permalink / raw)
  To: Arnd Bergmann, Daniel Vetter, David Airlie, Olof Johansson,
	Rob Herring, Sascha Hauer, Shawn Guo, soc, Thierry Reding
  Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
	linux-kernel, Pengutronix Kernel Team, dri-devel, Sam Ravnborg

Add "skov" entry for the SKOV A/S: https://www.skov.com/en/

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 62cb1d9341f5..738d4f44f0de 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1068,6 +1068,8 @@ patternProperties:
     description: Silicon Integrated Systems Corp.
   "^sitronix,.*":
     description: Sitronix Technology Corporation
+  "^skov,.*":
+    description: SKOV A/S
   "^skyworks,.*":
     description: Skyworks Solutions, Inc.
   "^smartlabs,.*":
-- 
2.30.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v4 2/3] dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
  2021-08-04  4:34 [PATCH v34 0/3] Mainline imx6 based SKOV boards Oleksij Rempel
  2021-08-04  4:34 ` [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S Oleksij Rempel
@ 2021-08-04  4:34 ` Oleksij Rempel
  2021-08-11 18:40   ` Rob Herring
  2021-08-04  4:34 ` [PATCH v4 3/3] ARM: dts: " Oleksij Rempel
  2021-08-04 13:55 ` [PATCH v34 0/3] Mainline imx6 based SKOV boards Arnd Bergmann
  3 siblings, 1 reply; 7+ messages in thread
From: Oleksij Rempel @ 2021-08-04  4:34 UTC (permalink / raw)
  To: Arnd Bergmann, Daniel Vetter, David Airlie, Olof Johansson,
	Rob Herring, Sascha Hauer, Shawn Guo, soc, Thierry Reding
  Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
	linux-kernel, Pengutronix Kernel Team, dri-devel, Sam Ravnborg

Add SKOV imx6q/dl LT2, LT6 and mi1010ait-1cp1 boards.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index e2097011c4b0..600dfe984ab3 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -221,6 +221,9 @@ properties:
               - prt,prti6q                # Protonic PRTI6Q board
               - prt,prtwd2                # Protonic WD2 board
               - rex,imx6q-rex-pro         # Rex Pro i.MX6 Quad Board
+              - skov,imx6q-skov-revc-lt2  # SKOV IMX6 CPU QuadCore lt2
+              - skov,imx6q-skov-revc-lt6  # SKOV IMX6 CPU QuadCore lt6
+              - skov,imx6q-skov-reve-mi1010ait-1cp1 # SKOV IMX6 CPU QuadCore mi1010ait-1cp1
               - solidrun,cubox-i/q        # SolidRun Cubox-i Dual/Quad
               - solidrun,hummingboard/q
               - solidrun,hummingboard2/q
@@ -378,6 +381,8 @@ properties:
               - prt,prtvt7                # Protonic VT7 board
               - rex,imx6dl-rex-basic      # Rex Basic i.MX6 Dual Lite Board
               - riot,imx6s-riotboard      # RIoTboard i.MX6S
+              - skov,imx6dl-skov-revc-lt2 # SKOV IMX6 CPU SoloCore lt2
+              - skov,imx6dl-skov-revc-lt6 # SKOV IMX6 CPU SoloCore lt6
               - solidrun,cubox-i/dl            # SolidRun Cubox-i Solo/DualLite
               - solidrun,hummingboard/dl
               - solidrun,hummingboard2/dl      # SolidRun HummingBoard2 Solo/DualLite
-- 
2.30.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v4 3/3] ARM: dts: add SKOV imx6q and imx6dl based boards
  2021-08-04  4:34 [PATCH v34 0/3] Mainline imx6 based SKOV boards Oleksij Rempel
  2021-08-04  4:34 ` [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S Oleksij Rempel
  2021-08-04  4:34 ` [PATCH v4 2/3] dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards Oleksij Rempel
@ 2021-08-04  4:34 ` Oleksij Rempel
  2021-08-04 13:55 ` [PATCH v34 0/3] Mainline imx6 based SKOV boards Arnd Bergmann
  3 siblings, 0 replies; 7+ messages in thread
From: Oleksij Rempel @ 2021-08-04  4:34 UTC (permalink / raw)
  To: Arnd Bergmann, Daniel Vetter, David Airlie, Olof Johansson,
	Rob Herring, Sascha Hauer, Shawn Guo, soc, Thierry Reding
  Cc: Sam Ravnborg, Søren Andersen, Juergen Borleis,
	Ulrich Ölmann, Michael Grzeschik, Marco Felsch, Lucas Stach,
	Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
	linux-kernel, Pengutronix Kernel Team, dri-devel

From: Sam Ravnborg <sam@ravnborg.org>

Add SKOV imx6q/dl LT2, LT6 and mi1010ait-1cp1 boards.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Søren Andersen <san@skov.dk>
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/Makefile                    |   5 +
 arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts    |  13 +
 arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts    | 106 ++++
 arch/arm/boot/dts/imx6q-skov-revc-lt2.dts     |  36 ++
 arch/arm/boot/dts/imx6q-skov-revc-lt6.dts     | 128 +++++
 .../dts/imx6q-skov-reve-mi1010ait-1cp1.dts    | 127 +++++
 arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi  |  54 ++
 arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi       | 477 ++++++++++++++++++
 8 files changed, 946 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts
 create mode 100644 arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts
 create mode 100644 arch/arm/boot/dts/imx6q-skov-revc-lt2.dts
 create mode 100644 arch/arm/boot/dts/imx6q-skov-revc-lt6.dts
 create mode 100644 arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
 create mode 100644 arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 828fefc9c436..ecff0743d35f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -475,6 +475,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-sabrelite.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-savageboard.dtb \
+	imx6dl-skov-revc-lt2.dtb \
+	imx6dl-skov-revc-lt6.dtb \
 	imx6dl-solidsense.dtb \
 	imx6dl-ts4900.dtb \
 	imx6dl-ts7970.dtb \
@@ -576,6 +578,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-sabresd.dtb \
 	imx6q-savageboard.dtb \
 	imx6q-sbc6x.dtb \
+	imx6q-skov-revc-lt2.dtb \
+	imx6q-skov-revc-lt6.dtb \
+	imx6q-skov-reve-mi1010ait-1cp1.dtb \
 	imx6q-solidsense.dtb \
 	imx6q-tbs2910.dtb \
 	imx6q-ts4900.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts b/arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts
new file mode 100644
index 000000000000..667b8faa1807
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU SoloCore";
+	compatible = "skov,imx6dl-skov-revc-lt2", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts b/arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts
new file mode 100644
index 000000000000..5dcc433fe2af
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU SoloCore";
+	compatible = "skov,imx6dl-skov-revc-lt6", "fsl,imx6dl";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "logictechno,lttd800480070-l6wh-rt";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-skov-revc-lt2.dts b/arch/arm/boot/dts/imx6q-skov-revc-lt2.dts
new file mode 100644
index 000000000000..f00add7b3048
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-skov-revc-lt2.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU QuadCore";
+	compatible = "skov,imx6q-skov-revc-lt2", "fsl,imx6q";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001f878
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001f878
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-skov-revc-lt6.dts b/arch/arm/boot/dts/imx6q-skov-revc-lt6.dts
new file mode 100644
index 000000000000..3e3b36ad362a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-skov-revc-lt6.dts
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU QuadCore";
+	compatible = "skov,imx6q-skov-revc-lt6", "fsl,imx6q";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	display {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "logictechno,lttd800480070-l6wh-rt";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001F878
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001F878
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts b/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
new file mode 100644
index 000000000000..7f1f19b74bfa
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU QuadCore";
+	compatible = "skov,imx6q-skov-reve-mi1010ait-1cp1", "fsl,imx6q";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	panel {
+		compatible = "multi-inno,mi1010ait-1cp";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+				 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+		wakeup-source;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			/* external 1 k pull up */
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x40010878
+			/* external 1 k pull up */
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x40010878
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001F878
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001F878
+		>;
+	};
+
+	pinctrl_touchscreen: touchscreengrp {
+		fsl,pins = <
+			/* external 10 k pull up */
+			/* CTP_INT */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
+			/* CTP_RST */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi b/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
new file mode 100644
index 000000000000..69ae430a53bd
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+&ecspi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	touchscreen@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 19 IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply  = <&reg_3v3>;
+		pendown-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
+		ti,x-plate-ohms = /bits/ 16 <850>;
+		ti,y-plate-ohms = /bits/ 16 <295>;
+		ti,pressure-min = /bits/ 16 <2>;
+		ti,pressure-max = /bits/ 16 <1500>;
+		ti,vref-mv	= /bits/ 16 <3300>;
+		ti,settle-delay-usec = /bits/ 16 <15>;
+		ti,vref-delay-usecs = /bits/ 16 <0>;
+		ti,penirq-recheck-delay-usecs = /bits/ 16 <100>;
+		ti,debounce-max = /bits/ 16 <100>;
+		ti,debounce-tol = /bits/ 16 <(~0)>;
+		ti,debounce-rep = /bits/ 16 <4>;
+		touchscreen-swapped-x-y;
+		touchscreen-inverted-y;
+		wakeup-source;
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D28__ECSPI4_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D22__ECSPI4_MISO			0x000b1
+			MX6QDL_PAD_EIM_D21__ECSPI4_SCLK			0x000b1
+			/* *no* external pull up */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x40000058
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			/* external pull up */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x10040
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi b/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
new file mode 100644
index 000000000000..77a91a97e6cf
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
@@ -0,0 +1,477 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	aliases {
+		can0 = &can1;
+		can1 = &can2;
+		mdio-gpio0 = &mdio;
+		nand = &gpmi;
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs;
+		usb0 = &usbh1;
+		usb1 = &usbotg;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, /* 24V */
+		              <&adc 1>; /* temperature */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "D1";
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_STATUS;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "D2";
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "D3";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	mdio: mdio {
+		compatible = "microchip,mdio-smi0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mdio>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>,
+			<&gpio1 22 GPIO_ACTIVE_HIGH>;
+
+		switch@0 {
+			compatible = "microchip,ksz8873";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_switch>;
+			interrupt-parent = <&gpio3>;
+			interrupt = <30 IRQ_TYPE_LEVEL_HIGH>;
+			reset-gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+			reg = <0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports@0 {
+					reg = <0>;
+					phy-mode = "internal";
+					label = "lan1";
+				};
+
+				ports@1 {
+					reg = <1>;
+					phy-mode = "internal";
+					label = "lan2";
+				};
+
+				ports@2 {
+					reg = <2>;
+					label = "cpu";
+					ethernet = <&fec>;
+					phy-mode = "rmii";
+
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+			};
+		};
+
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_5v0>;
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_24v0: regulator-24v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "24v0";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+	};
+
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can1_stby>;
+		regulator-name = "can1-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_can2_stby: regulator-can2-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can2_stby>;
+		regulator-name = "can2-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 11 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_vcc_mmc: regulator-vcc-mmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc>;
+		vin-supply = <&reg_3v3>;
+		regulator-name = "mmc_vcc_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+	};
+
+	reg_vcc_mmc_io: regulator-vcc-mmc-io {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc_io>;
+		vin-supply = <&reg_5v0>;
+		regulator-name = "mmc_io_supply";
+		regulator-type = "voltage";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		states = <1800000 0x1>, <3300000 0x0>;
+		startup-delay-us = <100>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can1_stby>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_can2_stby>;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <54000000>;
+		reg = <0>;
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	adc: adc@0 {
+		compatible = "microchip,mcp3002";
+		reg = <0>;
+		vref-supply = <&reg_3v3>;
+		spi-max-frequency = <1000000>;
+		#io-channel-cells = <1>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-mode = "rmii";
+	phy-supply = <&reg_3v3>;
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	i2c_rtc: rtc@51 {
+		compatible = "nxp,pcf85063";
+		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	#pwm-cells = <2>;
+	status = "okay";
+};
+
+&pwm3 {
+	/* used for LCD contrast control */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_5v0>;
+	disable-over-current;
+	status = "okay";
+};
+
+/* no usbh2 */
+&usbphynop1 {
+	status = "disabled";
+};
+
+/* no usbh3 */
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usbotg {
+	vbus-supply = <&reg_5v0>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	cap-power-off-card;
+	full-pwr-cycle;
+	bus-width = <4>;
+	max-frequency = <50000000>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	mmc-ddr-1_8v;
+	vmmc-supply = <&reg_vcc_mmc>;
+	vqmmc-supply = <&reg_vcc_mmc_io>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__FLEXCAN1_TX			0x3008
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX			0x1b000
+		>;
+	};
+
+	pinctrl_can1_stby: can1stbygrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x13008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+		>;
+	};
+
+	pinctrl_can2_stby: can2stbygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0xb1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0xb1
+			/* *no* external pull up */
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24			0x58
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO			0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI			0xb1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK			0xb1
+			/* external pull up */
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26			0x58
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* RMII 50 MHz */
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x100f5
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x100f5
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x100c0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x100c0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x100f5
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x100f5
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05			0x58
+			/* GPIO for "link active" */
+			MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24		0x3038
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE			0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE			0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B		0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B		0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B		0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B			0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B			0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00		0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01		0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02		0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03		0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04		0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05		0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06		0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07		0xb0b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			/* external 10 k pull up */
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x40010878
+			/* external 10 k pull up */
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x40010878
+		>;
+	};
+
+	pinctrl_mdio: mdiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__GPIO1_IO22		0x100b1
+			MX6QDL_PAD_ENET_MDC__GPIO1_IO31			0xb1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__PWM2_OUT			0x58
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT			0x58
+		>;
+	};
+
+	pinctrl_switch: switchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0xb0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			/* SoC internal pull up required */
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17059
+			/* SoC internal pull up required */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01			0x1b040
+			/* SoC internal pull up required */
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00			0x1b040
+		>;
+	};
+
+	pinctrl_vcc_mmc: vccmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08			0x58
+		>;
+	};
+
+	pinctrl_vcc_mmc_io: vccmmciogrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13			0x58
+		>;
+	};
+};
-- 
2.30.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v34 0/3] Mainline imx6 based SKOV boards
  2021-08-04  4:34 [PATCH v34 0/3] Mainline imx6 based SKOV boards Oleksij Rempel
                   ` (2 preceding siblings ...)
  2021-08-04  4:34 ` [PATCH v4 3/3] ARM: dts: " Oleksij Rempel
@ 2021-08-04 13:55 ` Arnd Bergmann
  3 siblings, 0 replies; 7+ messages in thread
From: Arnd Bergmann @ 2021-08-04 13:55 UTC (permalink / raw)
  To: Oleksij Rempel
  Cc: Arnd Bergmann, Daniel Vetter, David Airlie, Olof Johansson,
	Rob Herring, Sascha Hauer, Shawn Guo, SoC Team, Thierry Reding,
	DTML, Fabio Estevam, Linux ARM, Linux Kernel Mailing List,
	Pengutronix Kernel Team, dri-devel, Sam Ravnborg

On Wed, Aug 4, 2021 at 6:36 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>
> changes v4:
> - add vref-supply to adc@0
> - split gpio assignment for the mdio node

Hi Oleksij,

I've dropped the series from the soc patchwork, since this looks like
something that
should go through the i.MX tree. Please make it clear from the cover
letter and from
the 'to' list what you want to happen with the patches, and who should take care
of them.

Any patches that are meant for platform maintainers should not get sent to
soc@kernel.org. If you think you need me to review the patches, you can
send them cc my personal address.

      Arnd

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
  2021-08-04  4:34 ` [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S Oleksij Rempel
@ 2021-08-11 18:40   ` Rob Herring
  0 siblings, 0 replies; 7+ messages in thread
From: Rob Herring @ 2021-08-11 18:40 UTC (permalink / raw)
  To: Oleksij Rempel
  Cc: Rob Herring, Shawn Guo, Fabio Estevam, Olof Johansson, dri-devel,
	Arnd Bergmann, Pengutronix Kernel Team, Sascha Hauer,
	David Airlie, Daniel Vetter, linux-arm-kernel, soc,
	Thierry Reding, Sam Ravnborg, linux-kernel, devicetree

On Wed, 04 Aug 2021 06:34:37 +0200, Oleksij Rempel wrote:
> Add "skov" entry for the SKOV A/S: https://www.skov.com/en/
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v4 2/3] dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
  2021-08-04  4:34 ` [PATCH v4 2/3] dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards Oleksij Rempel
@ 2021-08-11 18:40   ` Rob Herring
  0 siblings, 0 replies; 7+ messages in thread
From: Rob Herring @ 2021-08-11 18:40 UTC (permalink / raw)
  To: Oleksij Rempel
  Cc: Sascha Hauer, linux-arm-kernel, dri-devel, Shawn Guo,
	David Airlie, Thierry Reding, Rob Herring, Olof Johansson,
	Pengutronix Kernel Team, devicetree, Daniel Vetter,
	Fabio Estevam, soc, Arnd Bergmann, Sam Ravnborg, linux-kernel

On Wed, 04 Aug 2021 06:34:38 +0200, Oleksij Rempel wrote:
> Add SKOV imx6q/dl LT2, LT6 and mi1010ait-1cp1 boards.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  Documentation/devicetree/bindings/arm/fsl.yaml | 5 +++++
>  1 file changed, 5 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2021-08-11 18:40 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-04  4:34 [PATCH v34 0/3] Mainline imx6 based SKOV boards Oleksij Rempel
2021-08-04  4:34 ` [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add an entry for SKOV A/S Oleksij Rempel
2021-08-11 18:40   ` Rob Herring
2021-08-04  4:34 ` [PATCH v4 2/3] dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards Oleksij Rempel
2021-08-11 18:40   ` Rob Herring
2021-08-04  4:34 ` [PATCH v4 3/3] ARM: dts: " Oleksij Rempel
2021-08-04 13:55 ` [PATCH v34 0/3] Mainline imx6 based SKOV boards Arnd Bergmann

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).