LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: kgunda@codeaurora.org
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>,
	Daniel Thompson <daniel.thompson@linaro.org>,
	Jingoo Han <jingoohan1@gmail.com>,
	Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>,
	dri-devel@lists.freedesktop.org, linux-fbdev@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	linux-leds@vger.kernel.org
Subject: Re: [PATCH V1 4/5] backlight: qcom-wled: Add support for OVP interrupt handling
Date: Tue, 08 May 2018 17:56:04 +0530	[thread overview]
Message-ID: <3736480b2712e2dd401fed0a635a25d7@codeaurora.org> (raw)
In-Reply-To: <20180507172152.GD2259@tuxbook-pro>

On 2018-05-07 22:51, Bjorn Andersson wrote:
> On Thu 03 May 02:57 PDT 2018, Kiran Gunda wrote:
> 
>> WLED peripheral has over voltage protection(OVP) circuitry and the OVP
>> fault is notified through an interrupt. Though this fault condition 
>> rising
>> is due to an incorrect hardware configuration is mitigated in the 
>> hardware,
>> it still needs to be detected and handled. Add support for it.
>> 
>> When WLED module is enabled, keep OVP fault interrupt disabled for 10 
>> ms to
>> account for soft start delay.
>> 
>> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
>> ---
>>  drivers/video/backlight/qcom-wled.c | 118 
>> +++++++++++++++++++++++++++++++++++-
>>  1 file changed, 116 insertions(+), 2 deletions(-)
>> 
>> diff --git a/drivers/video/backlight/qcom-wled.c 
>> b/drivers/video/backlight/qcom-wled.c
>> index 2cfba77..80ae084 100644
>> --- a/drivers/video/backlight/qcom-wled.c
>> +++ b/drivers/video/backlight/qcom-wled.c
>> @@ -23,14 +23,20 @@
>> 
>>  /* From DT binding */
>>  #define WLED_DEFAULT_BRIGHTNESS				2048
>> -
>> +#define WLED_SOFT_START_DLY_US				10000
>>  #define WLED3_SINK_REG_BRIGHT_MAX			0xFFF
>> 
>>  /* WLED3 Control registers */
>>  #define WLED3_CTRL_REG_FAULT_STATUS			0x08
>> +#define  WLED3_CTRL_REG_ILIM_FAULT_BIT			BIT(0)
>> +#define  WLED3_CTRL_REG_OVP_FAULT_BIT			BIT(1)
>> +#define  WLED4_CTRL_REG_SC_FAULT_BIT			BIT(2)
>> +
>> +#define WLED3_CTRL_REG_INT_RT_STS			0x10
>> 
>>  #define WLED3_CTRL_REG_MOD_EN				0x46
>>  #define  WLED3_CTRL_REG_MOD_EN_MASK			BIT(7)
>> +#define  WLED3_CTRL_REG_MOD_EN_BIT			BIT(7)
> 
> "BIT(7)" is not a "bit" it's a "mask", so perhaps you could use the
> define with that name...which has the same value?
> 
Sure. I will change it in next series.
>> 
>>  #define WLED3_CTRL_REG_FREQ				0x4c
>>  #define  WLED3_CTRL_REG_FREQ_MASK			GENMASK(3, 0)
>> @@ -161,9 +167,12 @@ struct wled {
>>  	u32 short_count;
>>  	const int *version;
>>  	int short_irq;
>> +	int ovp_irq;
>>  	bool force_mod_disable;
>> +	bool ovp_irq_disabled;
>> 
>>  	struct wled_config cfg;
>> +	struct delayed_work ovp_work;
>>  	int (*wled_set_brightness)(struct wled *wled, u16 brightness);
>>  	int (*wled_sync_toggle)(struct wled *wled);
>>  };
>> @@ -209,6 +218,32 @@ static int wled4_set_brightness(struct wled 
>> *wled, u16 brightness)
>>  	return 0;
>>  }
>> 
>> +static void wled_ovp_work(struct work_struct *work)
>> +{
>> +	u32 val;
>> +	int rc;
>> +
>> +	struct wled *wled = container_of(work,
>> +					 struct wled, ovp_work.work);
>> +
>> +	rc = regmap_read(wled->regmap, wled->ctrl_addr + 
>> WLED3_CTRL_REG_MOD_EN,
>> +			 &val);
>> +	if (rc < 0)
>> +		return;
>> +
>> +	if (val & WLED3_CTRL_REG_MOD_EN_BIT) {
>> +		if (wled->ovp_irq > 0 && wled->ovp_irq_disabled) {
>> +			enable_irq(wled->ovp_irq);
>> +			wled->ovp_irq_disabled = false;
>> +		}
>> +	} else {
>> +		if (wled->ovp_irq > 0 && !wled->ovp_irq_disabled) {
>> +			disable_irq(wled->ovp_irq);
>> +			wled->ovp_irq_disabled = true;
>> +		}
>> +	}
>> +}
>> +
>>  static int wled_module_enable(struct wled *wled, int val)
>>  {
>>  	int rc;
>> @@ -220,7 +255,12 @@ static int wled_module_enable(struct wled *wled, 
>> int val)
>>  				WLED3_CTRL_REG_MOD_EN,
>>  				WLED3_CTRL_REG_MOD_EN_MASK,
>>  				WLED3_CTRL_REG_MOD_EN_MASK);
>> -	return rc;
>> +	if (rc < 0)
>> +		return rc;
>> +
>> +	schedule_delayed_work(&wled->ovp_work, WLED_SOFT_START_DLY_US);
> 
> Do you really want to delay the work on disable?
> 
> Wouldn't it be better to use a delay worker for the enablement and in
> the disable case you cancel the work and just disable_irq() directly
> here.
> 
Sure. Will do it in the next series.
> But more importantly, if this is only related to auto detection, do you
> really want to enable/disable the ovp_irq after you have detected the
> string configuration?
> 
Ok. This is used for the genuine OVP detection and for the auto 
detection as well.
>> +
>> +	return 0;
>>  }
>> 
>>  static int wled3_sync_toggle(struct wled *wled)
>> @@ -346,6 +386,36 @@ static irqreturn_t wled_short_irq_handler(int 
>> irq, void *_wled)
>>  	return IRQ_HANDLED;
>>  }
>> 
>> +static irqreturn_t wled_ovp_irq_handler(int irq, void *_wled)
>> +{
>> +	struct wled *wled = _wled;
>> +	int rc;
>> +	u32 int_sts, fault_sts;
>> +
>> +	rc = regmap_read(wled->regmap,
>> +			 wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS, &int_sts);
>> +	if (rc < 0) {
>> +		dev_err(wled->dev, "Error in reading WLED3_INT_RT_STS rc=%d\n",
>> +			rc);
>> +		return IRQ_HANDLED;
>> +	}
>> +
>> +	rc = regmap_read(wled->regmap, wled->ctrl_addr +
>> +			 WLED3_CTRL_REG_FAULT_STATUS, &fault_sts);
>> +	if (rc < 0) {
>> +		dev_err(wled->dev, "Error in reading WLED_FAULT_STATUS rc=%d\n",
>> +			rc);
>> +		return IRQ_HANDLED;
>> +	}
>> +
>> +	if (fault_sts &
>> +		(WLED3_CTRL_REG_OVP_FAULT_BIT | WLED3_CTRL_REG_ILIM_FAULT_BIT))
>> +		dev_dbg(wled->dev, "WLED OVP fault detected, int_sts=%x fault_sts= 
>> %x\n",
>> +			int_sts, fault_sts);
>> +
> 
> It's hard to give a good review on this, as the actual logic comes in
> the next patch. And as these two patches both implement auto detection
> (without a clear separation) I think you should squash them.
> Ok. I will squash them in the next series.
>> +	return IRQ_HANDLED;
>> +}
>> +
>>  static int wled3_setup(struct wled *wled)
>>  {
>>  	u16 addr;
>> @@ -821,6 +891,44 @@ static int wled_configure_short_irq(struct wled 
>> *wled,
>>  	return rc;
>>  }
>> 
>> +static int wled_configure_ovp_irq(struct wled *wled,
>> +				  struct platform_device *pdev)
>> +{
>> +	int rc = 0;
>> +	u32 val;
>> +
>> +	if (*wled->version == WLED_PM8941)
>> +		return 0;
>> +
>> +	wled->ovp_irq = platform_get_irq_byname(pdev, "ovp");
>> +	if (wled->ovp_irq < 0) {
>> +		dev_dbg(&pdev->dev, "ovp irq is not used\n");
>> +		return 0;
>> +	}
>> +
>> +	rc = devm_request_threaded_irq(wled->dev, wled->ovp_irq, NULL,
>> +				       wled_ovp_irq_handler, IRQF_ONESHOT,
>> +				       "wled_ovp_irq", wled);
>> +	if (rc < 0) {
>> +		dev_err(wled->dev, "Unable to request ovp_irq (err:%d)\n",
>> +			rc);
> 
> wled->ovp_irq might be > 0 here which means wled_ovp_work() will find 
> it
> valid and call enabled_irq()/disable_irq() on it.
> 
Ok. I will make it '0' if the "request_threaded_irq" fails.
>> +		return 0;
>> +	}
>> +
> 
> Regards,
> Bjorn

  reply	other threads:[~2018-05-08 12:26 UTC|newest]

Thread overview: 31+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-05-03  9:57 [PATCH V1 0/5] backlight: qcom-wled: Support for QCOM wled driver Kiran Gunda
2018-05-03  9:57 ` [PATCH V1 1/5] qcom: wled: Rename pm8941-wled.c to qcom-wled.c Kiran Gunda
2018-05-07 15:41   ` Bjorn Andersson
2018-05-10 11:10   ` Pavel Machek
2018-05-03  9:57 ` [PATCH V1 2/5] backlight: qcom-wled: Add support for WLED4 peripheral Kiran Gunda
2018-05-07 16:20   ` Bjorn Andersson
2018-05-08 10:25     ` kgunda
2018-05-08 17:17       ` Bjorn Andersson
2018-05-09  5:15         ` kgunda
2018-05-17  9:47       ` kgunda
2018-05-17 12:31         ` Rob Herring
2018-05-17 15:10           ` kgunda
2018-05-18 12:20             ` Rob Herring
2018-05-14 16:57   ` Pavel Machek
2018-05-15  4:55     ` kgunda
2018-05-03  9:57 ` [PATCH V1 3/5] backlight: qcom-wled: Add support for short circuit handling Kiran Gunda
2018-05-07  8:06   ` Dan Carpenter
2018-05-07  9:08     ` kgunda
2018-05-07 17:06   ` Bjorn Andersson
2018-05-08 10:35     ` kgunda
2018-05-03  9:57 ` [PATCH V1 4/5] backlight: qcom-wled: Add support for OVP interrupt handling Kiran Gunda
2018-05-07 17:21   ` Bjorn Andersson
2018-05-08 12:26     ` kgunda [this message]
2018-05-08 17:19       ` Bjorn Andersson
2018-05-09  5:06         ` kgunda
2018-05-09  6:16           ` kgunda
2018-05-03  9:57 ` [PATCH V1 5/5] backlight: qcom-wled: Add auto string detection logic Kiran Gunda
2018-05-07 18:10   ` Bjorn Andersson
2018-05-09  7:14     ` kgunda
2018-05-14 17:02       ` Bjorn Andersson
2018-05-15  4:50         ` kgunda

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3736480b2712e2dd401fed0a635a25d7@codeaurora.org \
    --to=kgunda@codeaurora.org \
    --cc=b.zolnierkie@samsung.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=daniel.thompson@linaro.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=jingoohan1@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-fbdev@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --subject='Re: [PATCH V1 4/5] backlight: qcom-wled: Add support for OVP interrupt handling' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).