LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* Re: PROBLEM: sata_sil24 lockups under heavy i/o
       [not found] <fa.xijtCUCn78j3D/nyqVcCMUn1RIA@ifi.uio.no>
@ 2007-01-04 23:29 ` Robert Hancock
  0 siblings, 0 replies; 6+ messages in thread
From: Robert Hancock @ 2007-01-04 23:29 UTC (permalink / raw)
  To: Mark Wagner; +Cc: linux-kernel

Mark Wagner wrote:
> [1.] One line summary of the problem:
> 
> sata_sil24 lockups under heavy i/o
> 
> [2.] Full description of the problem/report:
> 
> I have a PCI-based sata_sil24 card. It has 4 ports. It was functioning
> well with two disks attached. Once I attached 2 additional disks (for
> a total of 4) and started heavy i/o (extending a software raid5 device)
> the system began locking up for a few minutes at a time. After the
> system recovers the disk transfer speed is reduced from UDMA/100 to
> UDMA/66 or UDMA/44.

I don't think this is anything to do with the sata_sil24 driver. 
Something really wierd seems to be going on with interrupts on this machine:

> /proc/interrupts
> 
>           CPU0
>   0:   20507744    XT-PIC-XT        timer
>   1:        262    XT-PIC-XT        i8042
>   2:          0    XT-PIC-XT        cascade
>   5:     962175    XT-PIC-XT        sym53c8xx, uhci_hcd:usb1,
> uhci_hcd:usb2
>   7:       3678    XT-PIC-XT        parport0
>   8:          2    XT-PIC-XT        rtc
>  10:    9153035    XT-PIC-XT        ide2, eth0
>  11:         30    XT-PIC-XT        sym53c8xx
>  12:    1026266    XT-PIC-XT        libata
>  14:     840214    XT-PIC-XT        ide0
>  15:     569928    XT-PIC-XT        ide1
> NMI:      11264
> LOC:   20506755
> ERR:        234
> MIS:          0
> 
> Output of dmesg:
> 

...

> Local APIC disabled by BIOS -- reenabling.
> Found and enabled local APIC!

Hmm, you might want to try not forcing the local APIC enabled by 
removing the lapic option from the kernel command line. Don't know if it 
could be related though.

> VP_IDE: IDE controller at PCI slot 0000:00:04.1
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:04.1
>     ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
>     ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
> Probing IDE interface ide0...
> input: AT Translated Set 2 keyboard as /class/input/input0
> hda: MAXTOR STM3160812A, ATA DISK drive
> hda: IRQ probe failed (0xfffffef8)
> hdb: WDC WD1600JB-00EVA0, ATA DISK drive
> hdb: IRQ probe failed (0xfffffef8)
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: IC35L120AVVA07-0, ATA DISK drive
> hdc: IRQ probe failed (0xffffbef8)
> hdd: WDC WD1200JB-00GVA0, ATA DISK drive
> hdd: IRQ probe failed (0xffffbef8)

These "IRQ proble failed" errors don't seem right at all.

Then:

> NETDEV WATCHDOG: eth0: transmit timed out
> eth0: transmit timed out, tx_status 00 status e000.
>   diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
>   Flags; bus-master 1, dirty 203390(14) current 203406(14)
>   Transmit list 01bea840 vs. c1beaac0.

So eth0's not happy.

> ata2.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen
> ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata2.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata2.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata2: hard resetting port

The SATA card is getting timeouts. And from your other mail:

 > hda: DMA timeout error
 > hda: dma timeout error: status=0x58 { DriveReady SeekComplete 
DataRequest }
 > ide: failed opcode was: unknown
 > hda: status timeout: status=0xd0 { Busy }
 > ide: failed opcode was: unknown
 > hda: no DRQ after issuing MULTWRITE_EXT

Your onboard IDE controller is also timing out.. Sounds to me like some 
kind of general IRQ problem, though you'd have to be losing interrupts 
on IRQ 10, 12 and 14 which seems pretty extreme. Maybe a hardware 
problem, are you sure you have enough power to run this many drives in 
the box?

-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: PROBLEM: sata_sil24 lockups under heavy i/o
  2007-01-12 18:35     ` Mark Wagner
@ 2007-01-13  0:53       ` Tejun Heo
  0 siblings, 0 replies; 6+ messages in thread
From: Tejun Heo @ 2007-01-13  0:53 UTC (permalink / raw)
  To: Mark Wagner; +Cc: linux-kernel

Mark Wagner wrote:
> The sil24-connected sata drives are external and connected to their own
> power supply.
> 
> I've replaced the sil24-based card with a Promise SATA300 TX4 controller
> card and everything seems to work now.

Hmmm... sil24 fares well with four ports occupied.  Weird.  Care to give
it another shot?  Maybe pci bus contact was bad or something.

-- 
tejun

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: PROBLEM: sata_sil24 lockups under heavy i/o
  2007-01-07  6:27   ` Tejun Heo
@ 2007-01-12 18:35     ` Mark Wagner
  2007-01-13  0:53       ` Tejun Heo
  0 siblings, 1 reply; 6+ messages in thread
From: Mark Wagner @ 2007-01-12 18:35 UTC (permalink / raw)
  To: linux-kernel

On Sun, Jan 07, 2007 at 03:27:03PM +0900, Tejun Heo wrote:

> Mark Wagner wrote:
> [--snip--]
> >NETDEV WATCHDOG: eth0: transmit timed out
> >eth0: transmit timed out, tx_status 00 status e000.
> [--snip--]
> >hda: DMA timeout error
> >hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
> >ide: failed opcode was: unknown
> >hda: status timeout: status=0xd0 { Busy }
> >ide: failed opcode was: unknown
> >hdb: DMA disabled
> >hda: no DRQ after issuing MULTWRITE_EXT
> >ata3.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
> >ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> >ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> >ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> >ata4: hard resetting port
> >ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> >ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> >ata2: hard resetting port
> >ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
> >ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> >ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> [--snip--]
> >i2c_adapter i2c-0: Transaction error!
> >i2c_adapter i2c-0: Transaction error!
> >i2c_adapter i2c-0: Transaction error!
> 
> It seems like your system is falling apart.  Timeouts are occurring 
> everywhere.  Either IRQ routing went wrong or your powersupply is not 
> providing enough power.  Adding two more disks to sil24 doesn't change 
> anything about IRQ routing.  If the system functioned okay w/ two disks 
> attached to sil24, give your system a better power supply or rewire 
> power cables such that each power lane is more equally loaded.

The sil24-connected sata drives are external and connected to their own
power supply.

I've replaced the sil24-based card with a Promise SATA300 TX4 controller
card and everything seems to work now.

Thanks,

Mark

-- 
Mark Wagner mark@lanfear.net

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: PROBLEM: sata_sil24 lockups under heavy i/o
  2007-01-04 18:16 ` Mark Wagner
@ 2007-01-07  6:27   ` Tejun Heo
  2007-01-12 18:35     ` Mark Wagner
  0 siblings, 1 reply; 6+ messages in thread
From: Tejun Heo @ 2007-01-07  6:27 UTC (permalink / raw)
  To: Mark Wagner; +Cc: linux-kernel

Hello,

Mark Wagner wrote:
[--snip--]
> NETDEV WATCHDOG: eth0: transmit timed out
> eth0: transmit timed out, tx_status 00 status e000.
[--snip--]
> hda: DMA timeout error
> hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
> ide: failed opcode was: unknown
> hda: status timeout: status=0xd0 { Busy }
> ide: failed opcode was: unknown
> hdb: DMA disabled
> hda: no DRQ after issuing MULTWRITE_EXT
> ata3.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
> ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata4: hard resetting port
> ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata2: hard resetting port
> ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
> ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
> ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
[--snip--]
> i2c_adapter i2c-0: Transaction error!
> i2c_adapter i2c-0: Transaction error!
> i2c_adapter i2c-0: Transaction error!

It seems like your system is falling apart.  Timeouts are occurring 
everywhere.  Either IRQ routing went wrong or your powersupply is not 
providing enough power.  Adding two more disks to sil24 doesn't change 
anything about IRQ routing.  If the system functioned okay w/ two disks 
attached to sil24, give your system a better power supply or rewire 
power cables such that each power lane is more equally loaded.

-- 
tejun


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: PROBLEM: sata_sil24 lockups under heavy i/o
  2007-01-03 17:30 Mark Wagner
@ 2007-01-04 18:16 ` Mark Wagner
  2007-01-07  6:27   ` Tejun Heo
  0 siblings, 1 reply; 6+ messages in thread
From: Mark Wagner @ 2007-01-04 18:16 UTC (permalink / raw)
  To: linux-kernel

On Wed, Jan 03, 2007 at 09:30:24AM -0800, Mark Wagner wrote:

> [1.] One line summary of the problem:
> 
> sata_sil24 lockups under heavy i/o
> 
> [2.] Full description of the problem/report:
> 
> I have a PCI-based sata_sil24 card. It has 4 ports. It was functioning
> well with two disks attached. Once I attached 2 additional disks (for
> a total of 4) and started heavy i/o (extending a software raid5 device)
> the system began locking up for a few minutes at a time. After the
> system recovers the disk transfer speed is reduced from UDMA/100 to
> UDMA/66 or UDMA/44.

Last night I performed a simultaneous dd on the 4 drives on the Sil3124
card like so:

dd if=/dev/sda of=/dev/null
dd if=/dev/sdb of=/dev/null
dd if=/dev/sdc of=/dev/null
dd if=/dev/sdd of=/dev/null

Three times the system temporarily locked up and then lowered
the speeds of the drives. They are currently at PIO4. What
might be causing this?

Here is the dmesg from when the problem occurred:

NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 13609990(6) current 13610006(6)
  Transmit list 01beaa20 vs. c1bea5c0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 0c0005ea
  2: @c1bea340  length 800005ea status 0c0005ea
  3: @c1bea3e0  length 800005ea status 0c0005ea
  4: @c1bea480  length 800005ea status 8c0005ea
  5: @c1bea520  length 800005ea status 8c0005ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0005ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 8000
  Flags; bus-master 1, dirty 13609990(6) current 13610006(6)
  Transmit list 01bea5c0 vs. c1bea5c0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 0c0005ea
  2: @c1bea340  length 800005ea status 0c0005ea
  3: @c1bea3e0  length 800005ea status 0c0005ea
  4: @c1bea480  length 800005ea status 8c0005ea
  5: @c1bea520  length 800005ea status 8c0005ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0005ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
hda: dma_timer_expiry: dma status == 0x61
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 8000
  Flags; bus-master 1, dirty 13609990(6) current 13610006(6)
  Transmit list 01bea5c0 vs. c1bea5c0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 0c0005ea
  2: @c1bea340  length 800005ea status 0c0005ea
  3: @c1bea3e0  length 800005ea status 0c0005ea
  4: @c1bea480  length 800005ea status 8c0005ea
  5: @c1bea520  length 800005ea status 8c0005ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0005ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdb: DMA disabled
hda: no DRQ after issuing MULTWRITE_EXT
ata3.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4: hard resetting port
ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2: hard resetting port
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1: hard resetting port
ide0: reset: success
ata3: soft resetting port
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
ata3: EH complete
SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
ata4: softreset failed (SRST command error)
ata4: follow-up softreset failed, retrying in 5 secs
ata2: softreset failed (SRST command error)
ata2: follow-up softreset failed, retrying in 5 secs
ata1: softreset failed (SRST command error)
ata1: follow-up softreset failed, retrying in 5 secs
ata4: hard resetting port
ata2: hard resetting port
ata1: hard resetting port
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to set xfermode (err_mask=0x120)
ata1.00: limiting speed to UDMA/33
ata1: failed to recover some devices, retrying in 5 secs
ata2.00: failed to set xfermode (err_mask=0x120)
ata2.00: limiting speed to UDMA/33
ata2: failed to recover some devices, retrying in 5 secs
ata4: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x1)
ATA: abnormal status 0xC1 on port 0xF8836007
ATA: abnormal status 0xC1 on port 0xF8836007
ata4.00: configured for UDMA/100
ata4: EH complete
ata1: hard resetting port
ata2: hard resetting port
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
ata2.00: configured for UDMA/33
ata2: EH complete
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
i2c_adapter i2c-0: Transaction error!
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 14351421(13) current 14351437(13)
  Transmit list 01bea5c0 vs. c1beaa20.
  0: @c1bea200  length 800005ea status 0c0105ea
  1: @c1bea2a0  length 800005ea status 0c0105ea
  2: @c1bea340  length 800005ea status 0c0105ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0005ea
  7: @c1bea660  length 800005ea status 0c0005ea
  8: @c1bea700  length 800005ea status 0c0005ea
  9: @c1bea7a0  length 800005ea status 0c0005ea
  10: @c1bea840  length 800005ea status 0c0005ea
  11: @c1bea8e0  length 800005ea status 8c0005ea
  12: @c1bea980  length 800005ea status 8c0005ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0105ea
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0800
  Flags; bus-master 1, dirty 14351421(13) current 14351437(13)
  Transmit list 01beaa20 vs. c1beaa20.
  0: @c1bea200  length 800005ea status 0c0105ea
  1: @c1bea2a0  length 800005ea status 0c0105ea
  2: @c1bea340  length 800005ea status 0c0105ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0005ea
  7: @c1bea660  length 800005ea status 0c0005ea
  8: @c1bea700  length 800005ea status 0c0005ea
  9: @c1bea7a0  length 800005ea status 0c0005ea
  10: @c1bea840  length 800005ea status 0c0005ea
  11: @c1bea8e0  length 800005ea status 8c0005ea
  12: @c1bea980  length 800005ea status 8c0005ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0105ea
eth0: Resetting the Tx ring pointer.
hda: dma_timer_expiry: dma status == 0x21
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0800
  Flags; bus-master 1, dirty 14351421(13) current 14351437(13)
  Transmit list 01beaa20 vs. c1beaa20.
  0: @c1bea200  length 800005ea status 0c0105ea
  1: @c1bea2a0  length 800005ea status 0c0105ea
  2: @c1bea340  length 800005ea status 0c0105ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0005ea
  7: @c1bea660  length 800005ea status 0c0005ea
  8: @c1bea700  length 800005ea status 0c0005ea
  9: @c1bea7a0  length 800005ea status 0c0005ea
  10: @c1bea840  length 800005ea status 0c0005ea
  11: @c1bea8e0  length 800005ea status 8c0005ea
  12: @c1bea980  length 800005ea status 8c0005ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0105ea
eth0: Resetting the Tx ring pointer.
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
sd 4:0:0:0: SCSI error: return code = 0x06000000
end_request: I/O error, dev sdc, sector 211498896
Buffer I/O error on device sdc, logical block 26437362
Buffer I/O error on device sdc, logical block 26437363
Buffer I/O error on device sdc, logical block 26437364
Buffer I/O error on device sdc, logical block 26437365
Buffer I/O error on device sdc, logical block 26437366
Buffer I/O error on device sdc, logical block 26437367
Buffer I/O error on device sdc, logical block 26437368
Buffer I/O error on device sdc, logical block 26437369
Buffer I/O error on device sdc, logical block 26437370
Buffer I/O error on device sdc, logical block 26437371
sd 4:0:0:0: SCSI error: return code = 0x06000000
end_request: I/O error, dev sdc, sector 211499152
ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1: hard resetting port
ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2: hard resetting port
ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4: hard resetting port
ide0: reset: success
ata1: softreset failed (SRST command error)
ata1: follow-up softreset failed, retrying in 5 secs
ata2: softreset failed (SRST command error)
ata2: follow-up softreset failed, retrying in 5 secs
ata4: softreset failed (SRST command error)
ata4: follow-up softreset failed, retrying in 5 secs
ata1: hard resetting port
ata2: hard resetting port
ata4: hard resetting port
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: failed to set xfermode (err_mask=0x120)
ata2.00: limiting speed to UDMA/25
ata2: failed to recover some devices, retrying in 5 secs
ata1.00: failed to set xfermode (err_mask=0x120)
ata1.00: limiting speed to UDMA/25
ata1: failed to recover some devices, retrying in 5 secs
ata4: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x1)
ATA: abnormal status 0xC1 on port 0xF8836007
ATA: abnormal status 0xC1 on port 0xF8836007
ata4.00: configured for UDMA/100
ata4: EH complete
ata2: hard resetting port
ata1: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/25
ata1: EH complete
ata2.00: configured for UDMA/25
ata2: EH complete
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
i2c_adapter i2c-0: Transaction error!
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 14500387(3) current 14500403(3)
  Transmit list 01bea840 vs. c1bea3e0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 8c0005ea
  2: @c1bea340  length 800005ea status 8c0005ea
  3: @c1bea3e0  length 80000456 status 0c010456
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 8000047e status 0c01047e
  10: @c1bea840  length 800005ea status 0c0005ea
  11: @c1bea8e0  length 800005ea status 0c0005ea
  12: @c1bea980  length 800005ea status 0c0005ea
  13: @c1beaa20  length 800005ea status 0c0005ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
hda: dma_timer_expiry: dma status == 0x21
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0800
  Flags; bus-master 1, dirty 14500387(3) current 14500403(3)
  Transmit list 01bea3e0 vs. c1bea3e0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 8c0005ea
  2: @c1bea340  length 800005ea status 8c0005ea
  3: @c1bea3e0  length 80000456 status 0c010456
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 8000047e status 0c01047e
  10: @c1bea840  length 800005ea status 0c0005ea
  11: @c1bea8e0  length 800005ea status 0c0005ea
  12: @c1bea980  length 800005ea status 0c0005ea
  13: @c1beaa20  length 800005ea status 0c0005ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: status error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1: hard resetting port
ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2: hard resetting port
ata4.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4: hard resetting port
ide0: reset: success
ata1: softreset failed (SRST command error)
ata1: follow-up softreset failed, retrying in 5 secs
ata2: softreset failed (SRST command error)
ata2: follow-up softreset failed, retrying in 5 secs
ata4: softreset failed (SRST command error)
ata4: follow-up softreset failed, retrying in 5 secs
ata1: hard resetting port
ata2: hard resetting port
ata4: hard resetting port
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: failed to set xfermode (err_mask=0x120)
ata1.00: limiting speed to UDMA/16
ata1: failed to recover some devices, retrying in 5 secs
ata2.00: failed to set xfermode (err_mask=0x120)
ata2.00: limiting speed to UDMA/16
ata2: failed to recover some devices, retrying in 5 secs
ata4: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x3)
ATA: abnormal status 0xC1 on port 0xF8836007
ATA: abnormal status 0xC1 on port 0xF8836007
ata4.00: configured for UDMA/100
ata4: EH complete
ata1: hard resetting port
ata2: hard resetting port
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/16
ata2: EH complete
ata1.00: configured for UDMA/16
ata1: EH complete
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 15217427(3) current 15217443(3)
  Transmit list 01beaac0 vs. c1bea3e0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 8c0005ea
  2: @c1bea340  length 800005ea status 8c0005ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 80000456 status 0c010456
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 15217427(3) current 15217443(3)
  Transmit list 01bea3e0 vs. c1bea3e0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 8c0005ea
  2: @c1bea340  length 800005ea status 8c0005ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 80000456 status 0c010456
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
hda: dma_timer_expiry: dma status == 0x21
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 8000
  Flags; bus-master 1, dirty 15217427(3) current 15217443(3)
  Transmit list 01bea3e0 vs. c1bea3e0.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 8c0005ea
  2: @c1bea340  length 800005ea status 8c0005ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 80000456 status 0c010456
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0005ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
sd 5:0:0:0: SCSI error: return code = 0x06000000
end_request: I/O error, dev sdd, sector 451246624
printk: 54 messages suppressed.
Buffer I/O error on device sdd, logical block 56405828
Buffer I/O error on device sdd, logical block 56405829
Buffer I/O error on device sdd, logical block 56405830
Buffer I/O error on device sdd, logical block 56405831
Buffer I/O error on device sdd, logical block 56405832
Buffer I/O error on device sdd, logical block 56405833
Buffer I/O error on device sdd, logical block 56405834
Buffer I/O error on device sdd, logical block 56405835
Buffer I/O error on device sdd, logical block 56405836
Buffer I/O error on device sdd, logical block 56405837
ata2.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2: hard resetting port
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1: hard resetting port
ata2: softreset failed (SRST command error)
ata2: follow-up softreset failed, retrying in 5 secs
ata1: softreset failed (SRST command error)
ata1: follow-up softreset failed, retrying in 5 secs
ata2: hard resetting port
ata1: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: failed to set xfermode (err_mask=0x120)
ata2.00: limiting speed to PIO4
ata2: failed to recover some devices, retrying in 5 secs
ata1.00: failed to set xfermode (err_mask=0x120)
ata1.00: limiting speed to PIO4
ata1: failed to recover some devices, retrying in 5 secs
ata2: hard resetting port
ata1: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for PIO4
ata1: EH complete
ata2.00: configured for PIO4
ata2: EH complete
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!

-- 
Mark Wagner mark@lanfear.net

^ permalink raw reply	[flat|nested] 6+ messages in thread

* PROBLEM: sata_sil24 lockups under heavy i/o
@ 2007-01-03 17:30 Mark Wagner
  2007-01-04 18:16 ` Mark Wagner
  0 siblings, 1 reply; 6+ messages in thread
From: Mark Wagner @ 2007-01-03 17:30 UTC (permalink / raw)
  To: linux-kernel

[1.] One line summary of the problem:

sata_sil24 lockups under heavy i/o

[2.] Full description of the problem/report:

I have a PCI-based sata_sil24 card. It has 4 ports. It was functioning
well with two disks attached. Once I attached 2 additional disks (for
a total of 4) and started heavy i/o (extending a software raid5 device)
the system began locking up for a few minutes at a time. After the
system recovers the disk transfer speed is reduced from UDMA/100 to
UDMA/66 or UDMA/44.

[3.] Keywords (i.e., modules, networking, kernel):

libata sata_sil24

[4.] Kernel version (from /proc/version):

Linux version 2.6.19-gentoo-r2 (root@cthulhu) (gcc version 4.1.1 (Gentoo
4.1.1-r3)) #1 Tue Dec 19 22:55:21 PST 2006

[5.] Most recent kernel version which did not have the bug:

Unknown.

[8.1.] Software (add the output of the ver_linux script here)

Linux cthulhu 2.6.19-gentoo-r2 #1 Tue Dec 19 22:55:21 PST 2006 i686 AMD
Athlon(tm) Processor AuthenticAMD GNU/Linux

Gnu C                  4.1.1
Gnu make               3.81
binutils               2.17
util-linux             2.12r
mount                  2.12r
module-init-tools      3.2.2
e2fsprogs              1.39
Linux C Library        > libc.2.4
Dynamic linker (ldd)   2.4
Procps                 3.2.7
Net-tools              1.60
Kbd                    1.12
Sh-utils               6.7
udev                   103
Modules Loaded         w83781d hwmon_vid lp usbhid 8250_pnp 8250
serial_core parport_pc pcspkr parport uhci_hcd via686a i2c_isa usbcore
i2c_viapro i2c_core

[8.2.] Processor information (from /proc/cpuinfo):

processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 6
model           : 4
model name      : AMD Athlon(tm) Processor
stepping        : 4
cpu MHz         : 1410.226
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 1
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
bogomips        : 2822.62

[8.3.] Module information (from /proc/modules):

w83781d 28008 1 - Live 0xfa367000
hwmon_vid 2240 1 w83781d, Live 0xf887d000
lp 8452 0 - Live 0xfa24c000
usbhid 32288 1 - Live 0xfa257000
8250_pnp 8704 0 - Live 0xf883b000
8250 17252 1 8250_pnp, Live 0xf8851000
serial_core 14976 1 8250, Live 0xf884c000
parport_pc 28644 1 - Live 0xfa202000
pcspkr 2240 0 - Live 0xf883f000
parport 30600 2 lp,parport_pc, Live 0xf8872000
uhci_hcd 16776 0 - Live 0xf8822000
via686a 13320 0 - Live 0xf8841000
i2c_isa 3584 2 w83781d,via686a, Live 0xf8839000
usbcore 99524 4 usbhid,uhci_hcd, Live 0xf8858000
i2c_viapro 6932 0 - Live 0xf882d000
i2c_core 15952 4 w83781d,via686a,i2c_isa,i2c_viapro, Live 0xf8828000

[8.4.] Loaded driver and hardware information (/proc/ioports,
/proc/iomem)

0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
  03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial
0778-077a : parport0
0cf8-0cff : PCI conf1
7800-783f : 0000:00:11.0
  7800-7807 : ide2
  7808-780f : ide3
  7810-783f : PDC20265
8000-8003 : 0000:00:11.0
8400-8407 : 0000:00:11.0
8800-8803 : 0000:00:11.0
  8802-8802 : ide2
9000-9007 : 0000:00:11.0
  9000-9007 : ide2
9400-947f : 0000:00:0b.0
9800-980f : 0000:00:0a.0
  9800-980f : sata_sil24
a000-a0ff : 0000:00:09.1
  a000-a0ff : sym53c8xx
a400-a4ff : 0000:00:09.0
  a400-a4ff : sym53c8xx
d000-d01f : 0000:00:04.3
  d000-d01f : uhci_hcd
d400-d41f : 0000:00:04.2
  d400-d41f : uhci_hcd
d800-d80f : 0000:00:04.1
  d800-d807 : ide0
  d808-d80f : ide1
e200-e27f : 0000:00:04.4
e400-e47f : pnp 00:12
e800-e80f : 0000:00:04.4
  e800-e807 : vt596_smbus

00000000-0009efff : System RAM
0009f000-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cf3ff : Video ROM
000d0000-000d27ff : Adapter ROM
000d4000-000d47ff : Adapter ROM
000d8000-000dbfff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3ffebfff : System RAM
  00100000-002efefe : Kernel code
  002efeff-003acf43 : Kernel data
3ffec000-3ffeefff : ACPI Tables
3ffef000-3fffefff : reserved
3ffff000-3fffffff : ACPI Non-volatile Storage
50000000-5007ffff : 0000:00:0a.0
50080000-5009ffff : 0000:00:0b.0
500a0000-500affff : 0000:00:09.0
500b0000-500bffff : 0000:00:09.1
500c0000-500cffff : 0000:00:11.0
d2000000-d201ffff : 0000:00:11.0
d2800000-d280007f : 0000:00:0b.0
d3000000-d3007fff : 0000:00:0a.0
  d3000000-d3007fff : sata_sil24
d3800000-d380007f : 0000:00:0a.0
  d3800000-d380007f : sata_sil24
d4000000-d4000fff : 0000:00:09.1
  d4000000-d4000fff : sym53c8xx
d4800000-d48000ff : 0000:00:09.1
  d4800000-d48000ff : sym53c8xx
d5000000-d5000fff : 0000:00:09.0
  d5000000-d5000fff : sym53c8xx
d5800000-d58000ff : 0000:00:09.0
  d5800000-d58000ff : sym53c8xx
d6000000-d7cfffff : PCI Bus #01
  d6000000-d6ffffff : 0000:01:00.0
d7f00000-e3ffffff : PCI Bus #01
  d7fe0000-d7ffffff : 0000:01:00.0
  d8000000-dfffffff : 0000:01:00.0
    d8000000-dfffffff : vesafb
e4000000-e7ffffff : 0000:00:00.0
ffff0000-ffffffff : reserved

[8.5.] PCI information ('lspci -vvv' as root)

00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
	Subsystem: ASUSTeK Computer Inc. A7V133/A7V133-C Mainboard
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
	Latency: 8
	Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: d6000000-d7cfffff
	Prefetchable memory behind bridge: d7f00000-e3ffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
	Subsystem: ASUSTeK Computer Inc. A7V133/A7V133-C Mainboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 4: I/O ports at d800 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
	Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin D routed to IRQ 5
	Region 4: I/O ports at d400 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
	Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin D routed to IRQ 5
	Region 4: I/O ports at d000 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
	Subsystem: ASUSTeK Computer Inc. A7V133/A7V133-C Mainboard
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin ? routed to IRQ 9
	Capabilities: [68] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14)
	Subsystem: LSI Logic / Symbios Logic Unknown device 1001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at a400 [size=256]
	Region 1: Memory at d5800000 (32-bit, non-prefetchable) [size=256]
	Region 2: Memory at d5000000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at 500a0000 [disabled] [size=64K]

00:09.1 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14)
	Subsystem: LSI Logic / Symbios Logic Unknown device 1001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 11
	Region 0: I/O ports at a000 [size=256]
	Region 1: Memory at d4800000 (32-bit, non-prefetchable) [size=256]
	Region 2: Memory at d4000000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at 500b0000 [disabled] [size=64K]

00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 01)
	Subsystem: Silicon Image, Inc. Unknown device 6124
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 12
	Region 0: Memory at d3800000 (64-bit, non-prefetchable) [size=128]
	Region 2: Memory at d3000000 (64-bit, non-prefetchable) [size=32K]
	Region 4: I/O ports at 9800 [size=16]
	[virtual] Expansion ROM at 50000000 [disabled] [size=512K]
	Capabilities: [64] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [40] PCI-X non-bridge device
		Command: DPERE- ERO+ RBC=512 OST=12
		Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
	Capabilities: [54] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000

00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
	Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 9400 [size=128]
	Region 1: Memory at d2800000 (32-bit, non-prefetchable) [size=128]
	[virtual] Expansion ROM at 50080000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 Mass storage controller: Promise Technology, Inc. PDC20265 (FastTrak100 Lite/Ultra100) (rev 02)
	Subsystem: Promise Technology, Inc. Ultra100
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 9000 [size=8]
	Region 1: I/O ports at 8800 [size=4]
	Region 2: I/O ports at 8400 [size=8]
	Region 3: I/O ports at 8000 [size=4]
	Region 4: I/O ports at 7800 [size=64]
	Region 5: Memory at d2000000 (32-bit, non-prefetchable) [size=128K]
	Expansion ROM at 500c0000 [size=64K]
	Capabilities: [58] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: nVidia Corporation NV34GL [Quadro FX 500/600 PCI] (rev a1) (prog-if 00 [VGA])
	Subsystem: nVidia Corporation Unknown device 01ba
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
	Expansion ROM at d7fe0000 [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 3.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

[8.6.] SCSI information (from /proc/scsi/scsi)

Attached devices:
Host: scsi0 Channel: 00 Id: 04 Lun: 00
  Vendor: EXABYTE  Model: VXA-2            Rev: 1003
  Type:   Sequential-Access                ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: Maxtor 6V300F0   Rev: VA11
  Type:   Direct-Access                    ANSI SCSI revision: 05
Host: scsi3 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: Maxtor 6V300F0   Rev: VA11
  Type:   Direct-Access                    ANSI SCSI revision: 05
Host: scsi4 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: ST3300620AS      Rev: 3.AA
  Type:   Direct-Access                    ANSI SCSI revision: 05
Host: scsi5 Channel: 00 Id: 00 Lun: 00
  Vendor: ATA      Model: ST3300620AS      Rev: 3.AA
  Type:   Direct-Access                    ANSI SCSI revision: 05

[8.7.] Other information

/proc/interrupts

          CPU0
  0:   20507744    XT-PIC-XT        timer
  1:        262    XT-PIC-XT        i8042
  2:          0    XT-PIC-XT        cascade
  5:     962175    XT-PIC-XT        sym53c8xx, uhci_hcd:usb1,
uhci_hcd:usb2
  7:       3678    XT-PIC-XT        parport0
  8:          2    XT-PIC-XT        rtc
 10:    9153035    XT-PIC-XT        ide2, eth0
 11:         30    XT-PIC-XT        sym53c8xx
 12:    1026266    XT-PIC-XT        libata
 14:     840214    XT-PIC-XT        ide0
 15:     569928    XT-PIC-XT        ide1
NMI:      11264
LOC:   20506755
ERR:        234
MIS:          0

Output of dmesg:

Linux version 2.6.19-gentoo-r2 (root@cthulhu) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 Tue Dec 19 22:55:21 PST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffec000 (usable)
 BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data)
 BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 262124) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   262124
early_node_map[1] active PFN ranges
    0:        0 ->   262124
On node 0 totalpages: 262124
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 255 pages used for memmap
  HighMem zone: 32493 pages, LIFO batch:7
DMI 2.3 present.
Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000)
Detected 1410.226 MHz processor.
Built 1 zonelists.  Total pages: 260077
Kernel command line: root=/dev/hda3 nmi_watchdog=1 video=vesafb:ywrap,mtrr,1024x768-16@72 splash=verbose,theme:emergence console=tty1 lapic
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034748k/1048496k available (1983k kernel code, 13024k reserved, 756k data, 172k init, 130992k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffaf000 - 0xfffff000   ( 320 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc03b0000 - 0xc03db000   ( 172 kB)
      .data : 0xc02efeff - 0xc03acf44   ( 756 kB)
      .text : 0xc0100000 - 0xc02efeff   (1983 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2822.62 BogoMIPS (lpj=14113144)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(tm) Processor stepping 04
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 792k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1180, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc4f0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc520, dseg 0xf0000
PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
SCSI subsystem initialized
libata version 2.00 loaded.
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
PCI quirk: region e200-e27f claimed by vt82c686 HW-mon
PCI quirk: region e800-e80f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
PCI: Using IRQ router VIA [1106/0686] at 0000:00:04.0
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:0b.0
PCI: Sharing IRQ 10 with 0000:00:11.0
spurious 8259A interrupt: IRQ7.
PCI: BIOS reporting unknown device 00:48
PCI: Device 0000:00:09.1 not found by BIOS
pnp: 00:12: ioport range 0xe400-0xe47f has been reserved
pnp: 00:12: ioport range 0xe800-0xe83f could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: d6000000-d7cfffff
  PREFETCH window: d7f00000-e3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
Real Time Clock Driver v1.12ac
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
[drm] Initialized drm 1.0.1 20051102
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
vesafb: unrecognized option mtrr
vesafb: NVIDIA Corporation, NV34 Board - q162-4nz, Chip Rev    (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:f0c0
vesafb: pmi: set display start = c00cf0f6, set palette = c00cf160
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: VBIOS/hardware doesn't support DDC transfers
vesafb: no monitor limits have been set
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=12288
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 0
vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 24576k, total 131072k
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
PCI: Enabling device 0000:00:0b.0 (0014 -> 0017)
PCI: Found IRQ 10 for device 0000:00:0b.0
PCI: Sharing IRQ 10 with 0000:00:11.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0b.0: 3Com PCI 3c905B Cyclone 100baseTx at f8816000.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:04.1
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
hda: MAXTOR STM3160812A, ATA DISK drive
hda: IRQ probe failed (0xfffffef8)
hdb: WDC WD1600JB-00EVA0, ATA DISK drive
hdb: IRQ probe failed (0xfffffef8)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: IC35L120AVVA07-0, ATA DISK drive
hdc: IRQ probe failed (0xffffbef8)
hdd: WDC WD1200JB-00GVA0, ATA DISK drive
hdd: IRQ probe failed (0xffffbef8)
ide1 at 0x170-0x177,0x376 on irq 15
PDC20265: IDE controller at PCI slot 0000:00:11.0
PCI: Found IRQ 10 for device 0000:00:11.0
PCI: Sharing IRQ 10 with 0000:00:0b.0
PDC20265: chipset revision 2
PDC20265: ROM enabled at 0x500c0000
PDC20265: 100% native mode on irq 10
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
    ide2: BM-DMA at 0x7800-0x7807, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0x7808-0x780f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: IC35L120AVVA07-0, ATA DISK drive
ide2 at 0x9000-0x9007,0x8802 on irq 10
Probing IDE interface ide3...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: max request size: 512KiB
hdb: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hdb: cache flushes supported
 hdb: hdb1
hdc: max request size: 128KiB
hdc: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hdc: cache flushes supported
 hdc: hdc1 hdc2 hdc3
hdd: max request size: 512KiB
hdd: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hdd: cache flushes supported
 hdd: hdd1 hdd2 hdd3
hde: max request size: 128KiB
hde: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hde: cache flushes supported
 hde: hde1 hde2 hde3
PCI: setting IRQ 5 as level-triggered
PCI: Found IRQ 5 for device 0000:00:09.0
PCI: Sharing IRQ 5 with 0000:00:04.2
PCI: Sharing IRQ 5 with 0000:00:04.3
sym0: <875> rev 0x14 at pci 0000:00:09.0 irq 5
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
scsi 0:0:4:0: Sequential-Access EXABYTE  VXA-2            1003 PQ: 0 ANSI: 2
 target0:0:4: Beginning Domain Validation
 target0:0:4: asynchronous
 target0:0:4: wide asynchronous
 target0:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
 target0:0:4: Domain Validation skipping write tests
 target0:0:4: Ending Domain Validation
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:09.1
sym1: <875> rev 0x14 at pci 0000:00:09.1 irq 11
sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.3
st: Version 20050830, fixed bufsize 32768, s/g segs 256
st 0:0:4:0: Attached scsi tape st0
st0: try direct i/o: yes (alignment 512 B)
st 0:0:4:0: Attached scsi generic sg0 type 1
sata_sil24 0000:00:0a.0: version 0.3
PCI: setting IRQ 12 as level-triggered
PCI: Found IRQ 12 for device 0000:00:0a.0
ata1: SATA max UDMA/100 cmd 0xF8830000 ctl 0x0 bmdma 0x0 irq 12
ata2: SATA max UDMA/100 cmd 0xF8832000 ctl 0x0 bmdma 0x0 irq 12
ata3: SATA max UDMA/100 cmd 0xF8834000 ctl 0x0 bmdma 0x0 irq 12
ata4: SATA max UDMA/100 cmd 0xF8836000 ctl 0x0 bmdma 0x0 irq 12
scsi2 : sata_sil24
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/100
scsi3 : sata_sil24
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 31/32)
ata2.00: ata2: dev 0 multi count 0
ata2.00: configured for UDMA/100
scsi4 : sata_sil24
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/100
scsi5 : sata_sil24
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
scsi 2:0:0:0: Direct-Access     ATA      Maxtor 6V300F0   VA11 PQ: 0 ANSI: 5
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 2:0:0:0: Attached scsi disk sda
sd 2:0:0:0: Attached scsi generic sg1 type 0
scsi 3:0:0:0: Direct-Access     ATA      Maxtor 6V300F0   VA11 PQ: 0 ANSI: 5
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3
sd 3:0:0:0: Attached scsi disk sdb
sd 3:0:0:0: Attached scsi generic sg2 type 0
scsi 4:0:0:0: Direct-Access     ATA      ST3300620AS      3.AA PQ: 0 ANSI: 5
SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3
sd 4:0:0:0: Attached scsi disk sdc
sd 4:0:0:0: Attached scsi generic sg3 type 0
scsi 5:0:0:0: Direct-Access     ATA      ST3300620AS      3.AA PQ: 0 ANSI: 5
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
 sdd: sdd1 sdd2 sdd3
sd 5:0:0:0: Attached scsi disk sdd
sd 5:0:0:0: Attached scsi generic sg4 type 0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1    492 MB/s
raid6: int32x2    560 MB/s
raid6: int32x4    518 MB/s
raid6: int32x8    416 MB/s
raid6: mmxx1     1164 MB/s
raid6: mmxx2     1974 MB/s
raid6: sse1x1    1060 MB/s
raid6: sse1x2    1675 MB/s
raid6: using algorithm sse1x2 (1675 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   8regs     :  1910.400 MB/sec
   8regs_prefetch:  1808.800 MB/sec
   32regs    :  1584.800 MB/sec
   32regs_prefetch:  1588.000 MB/sec
   pII_mmx   :  3846.800 MB/sec
   p5_mmx    :  5118.400 MB/sec
raid5: using function: p5_mmx (5118.400 MB/sec)
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Testing NMI watchdog ... OK.
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
Time: tsc clocksource has been installed.
md: invalid raid superblock magic on sdc3
md: sdc3 has invalid sb, not importing!
md: invalid raid superblock magic on sdd3
md: sdd3 has invalid sb, not importing!
md: autorun ...
md: considering sdd2 ...
md:  adding sdd2 ...
md: sdd1 has different UUID to sdd2
md:  adding sdc2 ...
md: sdc1 has different UUID to sdd2
md: sdb3 has different UUID to sdd2
md:  adding sdb2 ...
md: sdb1 has different UUID to sdd2
md: sda3 has different UUID to sdd2
md:  adding sda2 ...
md: sda1 has different UUID to sdd2
md: hde3 has different UUID to sdd2
md: hde2 has different UUID to sdd2
md: hde1 has different UUID to sdd2
md: hdd3 has different UUID to sdd2
md: hdd2 has different UUID to sdd2
md: hdd1 has different UUID to sdd2
md: hdc3 has different UUID to sdd2
md: hdc2 has different UUID to sdd2
md: hdc1 has different UUID to sdd2
md: hda6 has different UUID to sdd2
md: hda5 has different UUID to sdd2
md: created md4
md: bind<sda2>
md: bind<sdb2>
md: bind<sdc2>
md: bind<sdd2>
md: running: <sdd2><sdc2><sdb2><sda2>
raid5: device sdb2 operational as raid disk 0
raid5: device sda2 operational as raid disk 1
raid5: allocated 2116kB for md4
raid5: raid level 5 set md4 active with 2 out of 2 devices, algorithm 2
RAID5 conf printout:
 --- rd:2 wd:2
 disk 0, o:1, dev:sdb2
 disk 1, o:1, dev:sda2
md4: bitmap initialized from disk: read 12/12 pages, set 0 bits, status: 0
created bitmap (187 pages) for device md4
md: considering sdd1 ...
md:  adding sdd1 ...
md:  adding sdc1 ...
md: sdb3 has different UUID to sdd1
md:  adding sdb1 ...
md: sda3 has different UUID to sdd1
md:  adding sda1 ...
md: hde3 has different UUID to sdd1
md: hde2 has different UUID to sdd1
md: hde1 has different UUID to sdd1
md: hdd3 has different UUID to sdd1
md: hdd2 has different UUID to sdd1
md: hdd1 has different UUID to sdd1
md: hdc3 has different UUID to sdd1
md: hdc2 has different UUID to sdd1
md: hdc1 has different UUID to sdd1
md: hda6 has different UUID to sdd1
md: hda5 has different UUID to sdd1
md: created md3
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: running: <sdd1><sdc1><sdb1><sda1>
raid5: device sdd1 operational as raid disk 3
raid5: device sdc1 operational as raid disk 2
raid5: device sdb1 operational as raid disk 0
raid5: device sda1 operational as raid disk 1
raid5: allocated 4196kB for md3
raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:sdb1
 disk 1, o:1, dev:sda1
 disk 2, o:1, dev:sdc1
 disk 3, o:1, dev:sdd1
md3: bitmap initialized from disk: read 12/12 pages, set 0 bits, status: 0
created bitmap (187 pages) for device md3
md: considering sdb3 ...
md:  adding sdb3 ...
md:  adding sda3 ...
md: hde3 has different UUID to sdb3
md: hde2 has different UUID to sdb3
md: hde1 has different UUID to sdb3
md: hdd3 has different UUID to sdb3
md: hdd2 has different UUID to sdb3
md: hdd1 has different UUID to sdb3
md: hdc3 has different UUID to sdb3
md: hdc2 has different UUID to sdb3
md: hdc1 has different UUID to sdb3
md: hda6 has different UUID to sdb3
md: hda5 has different UUID to sdb3
md: created md5
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3>
raid5: device sdb3 operational as raid disk 0
raid5: device sda3 operational as raid disk 1
raid5: allocated 2116kB for md5
raid5: raid level 5 set md5 active with 2 out of 2 devices, algorithm 2
RAID5 conf printout:
 --- rd:2 wd:2
 disk 0, o:1, dev:sdb3
 disk 1, o:1, dev:sda3
md5: bitmap initialized from disk: read 12/12 pages, set 0 bits, status: 0
created bitmap (187 pages) for device md5
md: considering hde3 ...
md:  adding hde3 ...
md: hde2 has different UUID to hde3
md: hde1 has different UUID to hde3
md:  adding hdd3 ...
md: hdd2 has different UUID to hde3
md: hdd1 has different UUID to hde3
md:  adding hdc3 ...
md: hdc2 has different UUID to hde3
md: hdc1 has different UUID to hde3
md: hda6 has different UUID to hde3
md:  adding hda5 ...
md: created md2
md: bind<hda5>
md: bind<hdc3>
md: bind<hdd3>
md: bind<hde3>
md: running: <hde3><hdd3><hdc3><hda5>
raid5: device hde3 operational as raid disk 3
raid5: device hdd3 operational as raid disk 2
raid5: device hdc3 operational as raid disk 1
raid5: device hda5 operational as raid disk 0
raid5: allocated 4196kB for md2
raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:hda5
 disk 1, o:1, dev:hdc3
 disk 2, o:1, dev:hdd3
 disk 3, o:1, dev:hde3
md: considering hde2 ...
md:  adding hde2 ...
md: hde1 has different UUID to hde2
md:  adding hdd2 ...
md: hdd1 has different UUID to hde2
md:  adding hdc2 ...
md: hdc1 has different UUID to hde2
md:  adding hda6 ...
md: created md1
md: bind<hda6>
md: bind<hdc2>
md: bind<hdd2>
md: bind<hde2>
md: running: <hde2><hdd2><hdc2><hda6>
raid5: device hde2 operational as raid disk 3
raid5: device hdd2 operational as raid disk 2
raid5: device hdc2 operational as raid disk 1
raid5: device hda6 operational as raid disk 0
raid5: allocated 4196kB for md1
raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:hda6
 disk 1, o:1, dev:hdc2
 disk 2, o:1, dev:hdd2
 disk 3, o:1, dev:hde2
md: considering hde1 ...
md:  adding hde1 ...
md:  adding hdd1 ...
md:  adding hdc1 ...
md: created md0
md: bind<hdc1>
md: bind<hdd1>
md: bind<hde1>
md: running: <hde1><hdd1><hdc1>
raid5: device hde1 operational as raid disk 3
raid5: device hdd1 operational as raid disk 2
raid5: device hdc1 operational as raid disk 1
raid5: allocated 4196kB for md0
raid5: raid level 5 set md0 active with 3 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:3
 disk 1, o:1, dev:hdc1
 disk 2, o:1, dev:hdd1
 disk 3, o:1, dev:hde1
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
i2c_adapter i2c-9191: sensors disabled - enable with force_addr=0xe200
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
PCI: Found IRQ 5 for device 0000:00:04.2
PCI: Sharing IRQ 5 with 0000:00:04.3
PCI: Sharing IRQ 5 with 0000:00:09.0
uhci_hcd 0000:00:04.2: UHCI Host Controller
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:04.2: irq 5, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
input: PC Speaker as /class/input/input1
PCI: Found IRQ 5 for device 0000:00:04.3
PCI: Sharing IRQ 5 with 0000:00:04.2
PCI: Sharing IRQ 5 with 0000:00:09.0
uhci_hcd 0000:00:04.3: UHCI Host Controller
uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:04.3: irq 5, io base 0x0000d000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
usb 1-1: new low speed USB device using uhci_hcd and address 2
parport_pc: VIA parallel port: io=0x378, irq=7
usb 1-1: configuration #1 chosen from 1 choice
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
usbcore: registered new interface driver hiddev
hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS XS 1500 LCD FW:837.H4 .D USB FW:H4 ] on usb-0000:00:04.2-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
EXT3 FS on hda3, internal journal
lp0: using parport0 (interrupt-driven).
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2008116k swap on /dev/hda2.  Priority:-1 extents:1 across:2008116k
eth0:  setting full-duplex.
device eth0 entered promiscuous mode
process `named' is using obsolete setsockopt SO_BSDCOMPAT
fbsplash: console 1 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 1
fbsplash: console 2 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 2
fbsplash: console 3 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 3
fbsplash: console 4 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 4
fbsplash: console 5 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 5
fbsplash: console 6 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 6
fbsplash: console 7 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 7
fbsplash: console 8 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 8
fbsplash: console 9 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 9
fbsplash: console 10 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 10
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 203390(14) current 203406(14)
  Transmit list 01bea840 vs. c1beaac0.
eth0: command 0x3002 did not complete! Status=0x9000
  0: @c1bea200  length 800005ea status 0c0105ea
  1: @c1bea2a0  length 800005ea status 0c0105ea
  2: @c1bea340  length 800005ea status 0c0105ea
  3: @c1bea3e0  length 800005ea status 0c0105ea
  4: @c1bea480  length 800005ea status 0c0105ea
  5: @c1bea520  length 800005ea status 0c0105ea
  6: @c1bea5c0  length 800005ea status 0c0105ea
  7: @c1bea660  length 800005ea status 0c0105ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 8000009e status 0c00009e
  12: @c1bea980  length 800005ea status 8c0005ea
  13: @c1beaa20  length 800005ea status 8c0005ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0105ea
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 203434(10) current 203450(10)
  Transmit list 01beab60 vs. c1bea840.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 0c0005ea
  2: @c1bea340  length 800005ea status 0c0005ea
  3: @c1bea3e0  length 800005ea status 0c0005ea
  4: @c1bea480  length 800005ea status 0c0005ea
  5: @c1bea520  length 80000456 status 0c000456
  6: @c1bea5c0  length 800005ea status 0c0005ea
  7: @c1bea660  length 800005ea status 0c0005ea
  8: @c1bea700  length 80000576 status 8c000576
  9: @c1bea7a0  length 800001a3 status 8c0001a3
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 800005ea status 0c0105ea
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
ata2.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen
ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2: hard resetting port
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1: hard resetting port
ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen
ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata3.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata3.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata3: hard resetting port
ata4.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4: hard resetting port
ata2: softreset failed (SRST command error)
ata2: follow-up softreset failed, retrying in 5 secs
ata1: softreset failed (SRST command error)
ata1: follow-up softreset failed, retrying in 5 secs
ata3: softreset failed (SRST command error)
ata3: follow-up softreset failed, retrying in 5 secs
ata4: softreset failed (SRST command error)
ata4: follow-up softreset failed, retrying in 5 secs
ata2: hard resetting port
ata1: hard resetting port
ata3: hard resetting port
ata4: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: failed to set xfermode (err_mask=0x120)
ata2.00: limiting speed to UDMA/66
ata2: failed to recover some devices, retrying in 5 secs
ata1.00: failed to set xfermode (err_mask=0x120)
ata1.00: limiting speed to UDMA/66
ata1: failed to recover some devices, retrying in 5 secs
ata3: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x7)
ATA: abnormal status 0xC7 on port 0xF8834007
ATA: abnormal status 0xC7 on port 0xF8834007
ATA: abnormal status 0xC1 on port 0xF8836007
ATA: abnormal status 0xC1 on port 0xF8836007
ata3.00: configured for UDMA/100
ata3: EH complete
ata4.00: configured for UDMA/100
ata4: EH complete
ata2: hard resetting port
ata1: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/66
ata1: EH complete
ata2.00: configured for UDMA/66
ata2: EH complete
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 232152(8) current 232168(8)
  Transmit list 01beab60 vs. c1bea700.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 0c0005ea
  2: @c1bea340  length 800005ea status 0c0005ea
  3: @c1bea3e0  length 800005ea status 0c0005ea
  4: @c1bea480  length 80000456 status 0c000456
  5: @c1bea520  length 800005ea status 0c0005ea
  6: @c1bea5c0  length 800005ea status 8c0005ea
  7: @c1bea660  length 800005ea status 8c0005ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 80000162 status 0c010162
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: transmit timed out, tx_status 00 status e000.
  diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000
  Flags; bus-master 1, dirty 232152(8) current 232168(8)
  Transmit list 01bea700 vs. c1bea700.
  0: @c1bea200  length 800005ea status 0c0005ea
  1: @c1bea2a0  length 800005ea status 0c0005ea
  2: @c1bea340  length 800005ea status 0c0005ea
  3: @c1bea3e0  length 800005ea status 0c0005ea
  4: @c1bea480  length 80000456 status 0c000456
  5: @c1bea520  length 800005ea status 0c0005ea
  6: @c1bea5c0  length 800005ea status 8c0005ea
  7: @c1bea660  length 800005ea status 8c0005ea
  8: @c1bea700  length 800005ea status 0c0105ea
  9: @c1bea7a0  length 800005ea status 0c0105ea
  10: @c1bea840  length 800005ea status 0c0105ea
  11: @c1bea8e0  length 80000162 status 0c010162
  12: @c1bea980  length 800005ea status 0c0105ea
  13: @c1beaa20  length 800005ea status 0c0105ea
  14: @c1beaac0  length 800005ea status 0c0105ea
  15: @c1beab60  length 800005ea status 0c0005ea
eth0: Resetting the Tx ring pointer.
ata2.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen
ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata2: hard resetting port
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata1: hard resetting port
ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen
ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata3.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata3.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata3: hard resetting port
ata4.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout)
ata4: hard resetting port
ata2: softreset failed (SRST command error)
ata2: follow-up softreset failed, retrying in 5 secs
ata1: softreset failed (SRST command error)
ata1: follow-up softreset failed, retrying in 5 secs
ata3: softreset failed (SRST command error)
ata3: follow-up softreset failed, retrying in 5 secs
ata4: softreset failed (SRST command error)
ata4: follow-up softreset failed, retrying in 5 secs
ata2: hard resetting port
ata1: hard resetting port
ata3: hard resetting port
ata4: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: failed to set xfermode (err_mask=0x120)
ata2.00: limiting speed to UDMA/44
ata2: failed to recover some devices, retrying in 5 secs
ata1.00: failed to set xfermode (err_mask=0x120)
ata1.00: limiting speed to UDMA/44
ata1: failed to recover some devices, retrying in 5 secs
ata3: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x7)
ATA: abnormal status 0xC7 on port 0xF8834007
ATA: abnormal status 0xC7 on port 0xF8834007
ATA: abnormal status 0xC1 on port 0xF8836007
ATA: abnormal status 0xC1 on port 0xF8836007
ata3.00: configured for UDMA/100
ata3: EH complete
ata4.00: configured for UDMA/100
ata4: EH complete
ata2: hard resetting port
ata1: hard resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/44
ata1: EH complete
ata2.00: configured for UDMA/44
ata2: EH complete
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back



-- 
Mark Wagner mark@lanfear.net

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2007-01-13  0:54 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <fa.xijtCUCn78j3D/nyqVcCMUn1RIA@ifi.uio.no>
2007-01-04 23:29 ` PROBLEM: sata_sil24 lockups under heavy i/o Robert Hancock
2007-01-03 17:30 Mark Wagner
2007-01-04 18:16 ` Mark Wagner
2007-01-07  6:27   ` Tejun Heo
2007-01-12 18:35     ` Mark Wagner
2007-01-13  0:53       ` Tejun Heo

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).