LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* Re: ahci_softreset prevents acpi_power_off
       [not found]   ` <fa.kpxGqupQMKJxBBFrktFUzuoKc7c@ifi.uio.no>
@ 2007-01-14  1:23     ` Robert Hancock
  2007-01-14  3:18       ` Jeff Garzik
  2007-01-14 17:59       ` Faik Uygur
  0 siblings, 2 replies; 13+ messages in thread
From: Robert Hancock @ 2007-01-14  1:23 UTC (permalink / raw)
  To: Faik Uygur, linux-kernel; +Cc: Tejun Heo

Faik Uygur wrote:
>> What happens when you try to shutdown?  
> 
> Does not shutdown and freezes.
> 
> Hand copied last messages seen on console:
> 
> Synchronizing SCSI cache for disk sda:
> ACPI: PCI Interrupt for device 0000:06:08.0 disabled
> Power down.
> acpi_power_off called
>   hwsleep-0285 [01] enter_sleep_state    : Entering sleep state [S5]

Since you're getting to this point I think this has to be some kind of 
BIOS interaction causing this. The only thing that happens after the 
"Entering sleep state" is that the kernel writes to some ACPI registers 
to tell the hardware to power down. I think some laptop BIOSes do things 
on ACPI power down like try to park the drive heads, etc. and maybe this 
change that you found from git bisecting is somehow interfering with it 
doing this?

Might want to check for a BIOS update first of all..

-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-14  1:23     ` ahci_softreset prevents acpi_power_off Robert Hancock
@ 2007-01-14  3:18       ` Jeff Garzik
  2007-01-14 17:50         ` Faik Uygur
  2007-01-14 17:59       ` Faik Uygur
  1 sibling, 1 reply; 13+ messages in thread
From: Jeff Garzik @ 2007-01-14  3:18 UTC (permalink / raw)
  To: Robert Hancock; +Cc: Faik Uygur, linux-kernel, Tejun Heo

Robert Hancock wrote:
> Faik Uygur wrote:
>>> What happens when you try to shutdown?  
>>
>> Does not shutdown and freezes.
>>
>> Hand copied last messages seen on console:
>>
>> Synchronizing SCSI cache for disk sda:
>> ACPI: PCI Interrupt for device 0000:06:08.0 disabled
>> Power down.
>> acpi_power_off called
>>   hwsleep-0285 [01] enter_sleep_state    : Entering sleep state [S5]
> 
> Since you're getting to this point I think this has to be some kind of 
> BIOS interaction causing this. The only thing that happens after the 
> "Entering sleep state" is that the kernel writes to some ACPI registers 
> to tell the hardware to power down. I think some laptop BIOSes do things 
> on ACPI power down like try to park the drive heads, etc. and maybe this 
> change that you found from git bisecting is somehow interfering with it 
> doing this?
> 
> Might want to check for a BIOS update first of all..

It would be interesting to try -mm, which includes ACPI support for ATA...

	Jeff




^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-14  3:18       ` Jeff Garzik
@ 2007-01-14 17:50         ` Faik Uygur
  0 siblings, 0 replies; 13+ messages in thread
From: Faik Uygur @ 2007-01-14 17:50 UTC (permalink / raw)
  To: Jeff Garzik; +Cc: Robert Hancock, linux-kernel, Tejun Heo

14 Oca 2007 Paz 05:18 tarihinde şunları yazmıştınız:
>> [...]
> > Since you're getting to this point I think this has to be some kind of
> > BIOS interaction causing this. The only thing that happens after the
> > "Entering sleep state" is that the kernel writes to some ACPI registers
> > to tell the hardware to power down. I think some laptop BIOSes do things
> > on ACPI power down like try to park the drive heads, etc. and maybe this
> > change that you found from git bisecting is somehow interfering with it
> > doing this?
> >
> > Might want to check for a BIOS update first of all..
>
> It would be interesting to try -mm, which includes ACPI support for ATA...

With the same .config used and with CONFIG_SATA_ACPI defined as default
in 2.6.20-rc4-mm1 the machine did not poweroff again.

> 	Jeff

Regards,
- Faik

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-14  1:23     ` ahci_softreset prevents acpi_power_off Robert Hancock
  2007-01-14  3:18       ` Jeff Garzik
@ 2007-01-14 17:59       ` Faik Uygur
  2007-01-14 18:06         ` Arjan van de Ven
  1 sibling, 1 reply; 13+ messages in thread
From: Faik Uygur @ 2007-01-14 17:59 UTC (permalink / raw)
  To: Robert Hancock; +Cc: linux-kernel, Tejun Heo, Jeff Garzik

14 Oca 2007 Paz 03:23 tarihinde, Robert Hancock şunları yazmıştı: 
>> [...]
>> > Since you're getting to this point I think this has to be some kind of 
> BIOS interaction causing this. The only thing that happens after the
> "Entering sleep state" is that the kernel writes to some ACPI registers
> to tell the hardware to power down. I think some laptop BIOSes do things
> on ACPI power down like try to park the drive heads, etc. and maybe this
> change that you found from git bisecting is somehow interfering with it
> doing this?
>
> Might want to check for a BIOS update first of all..

Checked from the Sony support page for the laptop model and seems the BIOS 
version is the latest.

So it is nothing interesting but a broken BIOS.

Regards,
- Faik

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-14 17:59       ` Faik Uygur
@ 2007-01-14 18:06         ` Arjan van de Ven
  2007-01-14 18:58           ` Faik Uygur
  2007-01-15  4:02           ` Tejun Heo
  0 siblings, 2 replies; 13+ messages in thread
From: Arjan van de Ven @ 2007-01-14 18:06 UTC (permalink / raw)
  To: Faik Uygur; +Cc: Robert Hancock, linux-kernel, Tejun Heo, Jeff Garzik

On Sun, 2007-01-14 at 19:59 +0200, Faik Uygur wrote:
> 14 Oca 2007 Paz 03:23 tarihinde, Robert Hancock şunları yazmıştı: 
> >> [...]
> >> > Since you're getting to this point I think this has to be some kind of 
> > BIOS interaction causing this. The only thing that happens after the
> > "Entering sleep state" is that the kernel writes to some ACPI registers
> > to tell the hardware to power down. I think some laptop BIOSes do things
> > on ACPI power down like try to park the drive heads, etc. and maybe this
> > change that you found from git bisecting is somehow interfering with it
> > doing this?
> >
> > Might want to check for a BIOS update first of all..
> 
> Checked from the Sony support page for the laptop model and seems the BIOS 
> version is the latest.
> 
> So it is nothing interesting but a broken BIOS.

Hi,

I'd be interested in finding out how to best test this; if the bios is
really broken I'd love to add a test to the Linux-ready Firmware
Developer Kit for this, so that BIOS developers can make sure future
bioses do not suffer from this bug...

Greetings,
   Arjan van de Ven

-- 
if you want to mail me at work (you don't), use arjan (at) linux.intel.com
Test the interaction between Linux and your BIOS via http://www.linuxfirmwarekit.org


^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-14 18:06         ` Arjan van de Ven
@ 2007-01-14 18:58           ` Faik Uygur
  2007-01-15  4:02           ` Tejun Heo
  1 sibling, 0 replies; 13+ messages in thread
From: Faik Uygur @ 2007-01-14 18:58 UTC (permalink / raw)
  To: Arjan van de Ven; +Cc: Robert Hancock, linux-kernel, Tejun Heo, Jeff Garzik

14 Oca 2007 Paz 20:06 tarihinde, Arjan van de Ven şunları yazmıştı: 
> Hi,

Hi,

> I'd be interested in finding out how to best test this; if the bios is
> really broken I'd love to add a test to the Linux-ready Firmware
> Developer Kit for this, so that BIOS developers can make sure future
> bioses do not suffer from this bug...

I would be glad to help finding out for this.

> Greetings,
>    Arjan van de Ven

Regards,
- Faik

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-14 18:06         ` Arjan van de Ven
  2007-01-14 18:58           ` Faik Uygur
@ 2007-01-15  4:02           ` Tejun Heo
  2007-01-15 13:44             ` Jeff Garzik
  1 sibling, 1 reply; 13+ messages in thread
From: Tejun Heo @ 2007-01-15  4:02 UTC (permalink / raw)
  To: Arjan van de Ven; +Cc: Faik Uygur, Robert Hancock, linux-kernel, Jeff Garzik

Arjan van de Ven wrote:
> I'd be interested in finding out how to best test this; if the bios is
> really broken I'd love to add a test to the Linux-ready Firmware
> Developer Kit for this, so that BIOS developers can make sure future
> bioses do not suffer from this bug...

As reported, this is almost a butterfly effect.  ->softreset method is
only used during initialization and error recovery of ATA devices which
has almost nothing to do with the rest of the system.  This is almost
like 'changing my mixer input to line-in makes power off fail'.  (it's
more related due to ATA ACPI stuff and maybe that's why this happens but
I'm trying to make a point here.)

I'm not sure the test can be generalized and included in the firmware
devel kit.  This is a really really special obscure corner case bug
which, I believe, none will be able to recreate in the future unless the
same code is reused.  So, I think the right course of action is to bug
the manufacturer.  Eh.... Does that work with sony these days?

-- 
tejun

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-15  4:02           ` Tejun Heo
@ 2007-01-15 13:44             ` Jeff Garzik
  2007-01-15 13:55               ` Tejun Heo
  0 siblings, 1 reply; 13+ messages in thread
From: Jeff Garzik @ 2007-01-15 13:44 UTC (permalink / raw)
  To: Tejun Heo; +Cc: Arjan van de Ven, Faik Uygur, Robert Hancock, linux-kernel

Tejun Heo wrote:
> Arjan van de Ven wrote:
>> I'd be interested in finding out how to best test this; if the bios is
>> really broken I'd love to add a test to the Linux-ready Firmware
>> Developer Kit for this, so that BIOS developers can make sure future
>> bioses do not suffer from this bug...
> 
> As reported, this is almost a butterfly effect.  ->softreset method is
> only used during initialization and error recovery of ATA devices which
> has almost nothing to do with the rest of the system.  This is almost
> like 'changing my mixer input to line-in makes power off fail'.  (it's
> more related due to ATA ACPI stuff and maybe that's why this happens but
> I'm trying to make a point here.)

It's quite possible that the BIOS in question wants AHCI in some 
specific state at poweroff.

	Jeff




^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-15 13:44             ` Jeff Garzik
@ 2007-01-15 13:55               ` Tejun Heo
  0 siblings, 0 replies; 13+ messages in thread
From: Tejun Heo @ 2007-01-15 13:55 UTC (permalink / raw)
  To: Jeff Garzik; +Cc: Arjan van de Ven, Faik Uygur, Robert Hancock, linux-kernel

Jeff Garzik wrote:
> Tejun Heo wrote:
>> Arjan van de Ven wrote:
>>> I'd be interested in finding out how to best test this; if the bios is
>>> really broken I'd love to add a test to the Linux-ready Firmware
>>> Developer Kit for this, so that BIOS developers can make sure future
>>> bioses do not suffer from this bug...
>>
>> As reported, this is almost a butterfly effect.  ->softreset method is
>> only used during initialization and error recovery of ATA devices which
>> has almost nothing to do with the rest of the system.  This is almost
>> like 'changing my mixer input to line-in makes power off fail'.  (it's
>> more related due to ATA ACPI stuff and maybe that's why this happens but
>> I'm trying to make a point here.)
> 
> It's quite possible that the BIOS in question wants AHCI in some
> specific state at poweroff.

I would be surprised if this weren't an accident.  We reset the
controller during initialization, so whether softreset or hardreset is
used, the end status cannot be much different.  And, I really don't
wanna change ahci and/or libata for this.

-- 
tejun

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-13  1:12 ` Tejun Heo
  2007-01-13  5:59   ` Faik Uygur
@ 2007-01-13 12:10   ` Faik Uygur
  1 sibling, 0 replies; 13+ messages in thread
From: Faik Uygur @ 2007-01-13 12:10 UTC (permalink / raw)
  To: Tejun Heo; +Cc: linux-kernel, jgarzik, linux-ide

Hello Tejun,

13 Oca 2007 Cts 03:12 tarihinde şunları yazmıştınız:
> If possible, please post dmesg of shutting down.  

I have taken more detailed dmesg outputs of three configs with ATA_DEBUG and 
ATA_VERBOSE_DEBUG defined. You can find them at this address:

http://cekirdek.pardus.org.tr/~faik/tmp/ahci/

* ahci file is the output of CONFIG_SCSI_SATA_AHCI compiled config
* noahci file is the output of CONFIG_SCSI_SATA_AHCI not compiled config
* ahci-nullsoftreset is the output of CONFIG_SCSI_SATA_AHCI compiled config
but given NULL to softreset parameters of ata_do_eh in ahci.c

Also poweroff-config is the used .config file. Only CONFIG_SCSI_SATA_AHCI is
changed between them.

I am not familiar with AHCI nor ATA internals. So please ask if you would like 
to see anything more.

Regards,
- Faik

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-13  1:12 ` Tejun Heo
@ 2007-01-13  5:59   ` Faik Uygur
  2007-01-13 12:10   ` Faik Uygur
  1 sibling, 0 replies; 13+ messages in thread
From: Faik Uygur @ 2007-01-13  5:59 UTC (permalink / raw)
  To: Tejun Heo; +Cc: linux-kernel, jgarzik, linux-ide

13 Oca 2007 Cts 03:12 tarihinde, Tejun Heo şunları yazmıştı: 
> Hello,

Hello,

Thanks for the response.

> [...]
> Does everything else work okay?  
> Can you access devices attached to 
> ahci?  

Yes. While the machine is on, there seems to be no problem at all. Everything 
works great.

> What happens when you try to shutdown?  

Does not shutdown and freezes.

Hand copied last messages seen on console:

Synchronizing SCSI cache for disk sda:
ACPI: PCI Interrupt for device 0000:06:08.0 disabled
Power down.
acpi_power_off called
  hwsleep-0285 [01] enter_sleep_state    : Entering sleep state [S5]

> If possible, please post  
> dmesg of shutting down.  

Following is the netcat output. Please ask if you need anything else.

Regards,
- Faik

Linux version 2.6.20-rc4 (root@pardus) (gcc version 3.4.6) #58 SMP Sat Jan 13 
07:38:22 EET 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 
000000000009f800 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 
00000000000a0000 type: 2
copy_e820_map() start: 00000000000d8000 size: 0000000000028000 end: 
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fd90000 end: 
000000001fe90000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001fe90000 size: 000000000000d000 end: 
000000001fe9d000 type: 3
copy_e820_map() start: 000000001fe9d000 size: 0000000000063000 end: 
000000001ff00000 type: 4
copy_e820_map() start: 000000001ff00000 size: 0000000000100000 end: 
0000000020000000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010006000 end: 
00000000f0006000 type: 2
copy_e820_map() start: 00000000f0008000 size: 0000000000004000 end: 
00000000f000c000 type: 2
copy_e820_map() start: 00000000fed20000 size: 0000000000070000 end: 
00000000fed90000 type: 2
copy_e820_map() start: 00000000ff000000 size: 0000000001000000 end: 
0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fe90000 (usable)
 BIOS-e820: 000000001fe90000 - 000000001fe9d000 (ACPI data)
 BIOS-e820: 000000001fe9d000 - 000000001ff00000 (ACPI NVS)
 BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   130704
  HighMem    130704 ->   130704
early_node_map[1] active PFN ranges
    0:        0 ->   130704
DMI 2.3 present.
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1729.118 MHz processor.
Built 1 zonelists.  Total pages: 129045
Kernel command line: root=/dev/sda1 mudur=language:tr init=/bin/bash 
netconsole=4444@192.168.1.8/eth0,9353@192.168.1.3/00:13:02:50:5C:2B
netconsole: local port 4444
netconsole: local IP 192.168.1.8
netconsole: interface eth0
netconsole: remote port 9353
netconsole: remote IP 192.168.1.3
netconsole: remote ethernet address 00:13:02:50:5c:2b
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      16384
... CHAINHASH_SIZE:          8192
 memory used by lock dependency info: 1064 kB
 per task-struct memory footprint: 1200 bytes
------------------------
| Locking API testsuite:
----------------------------------------------------------------------------
                                 | spin |wlock |rlock |mutex | wsem | rsem |
  --------------------------------------------------------------------------
                     A-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                 A-B-B-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
             A-B-B-C-C-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
             A-B-C-A-B-C deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
         A-B-B-C-C-D-D-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
         A-B-C-D-B-D-D-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
         A-B-C-D-B-C-D-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                    double unlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                  initialize held:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                 bad unlock order:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
  --------------------------------------------------------------------------
              recursive read-lock:             |  ok  |             |  ok  |
           recursive read-lock #2:             |  ok  |             |  ok  |
            mixed read-write-lock:             |  ok  |             |  ok  |
            mixed write-read-lock:             |  ok  |             |  ok  |
  --------------------------------------------------------------------------
     hard-irqs-on + irq-safe-A/12:  ok  |  ok  |  ok  |
     soft-irqs-on + irq-safe-A/12:  ok  |  ok  |  ok  |
     hard-irqs-on + irq-safe-A/21:  ok  |  ok  |  ok  |
     soft-irqs-on + irq-safe-A/21:  ok  |  ok  |  ok  |
       sirq-safe-A => hirqs-on/12:  ok  |  ok  |  ok  |
       sirq-safe-A => hirqs-on/21:  ok  |  ok  |  ok  |
         hard-safe-A + irqs-on/12:  ok  |  ok  |  ok  |
         soft-safe-A + irqs-on/12:  ok  |  ok  |  ok  |
         hard-safe-A + irqs-on/21:  ok  |  ok  |  ok  |
         soft-safe-A + irqs-on/21:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/123:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/123:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/132:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/132:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/213:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/213:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/231:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/231:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/312:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/312:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/321:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/321:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/123:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/123:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/132:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/132:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/213:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/213:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/231:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/231:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/312:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/312:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/321:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/321:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/123:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/123:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/132:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/132:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/213:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/213:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/231:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/231:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/312:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/312:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/321:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/321:  ok  |  ok  |  ok  |
      hard-irq read-recursion/123:  ok  |
      soft-irq read-recursion/123:  ok  |
      hard-irq read-recursion/132:  ok  |
      soft-irq read-recursion/132:  ok  |
      hard-irq read-recursion/213:  ok  |
      soft-irq read-recursion/213:  ok  |
      hard-irq read-recursion/231:  ok  |
      soft-irq read-recursion/231:  ok  |
      hard-irq read-recursion/312:  ok  |
      soft-irq read-recursion/312:  ok  |
      hard-irq read-recursion/321:  ok  |
      soft-irq read-recursion/321:  ok  |
-------------------------------------------------------
Good, all 218 testcases passed! |
---------------------------------
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510196k/522816k available (1638k kernel code, 12096k reserved, 750k 
data, 180k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4f000 - 0xfffff000   ( 704 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdfe90000   ( 510 MB)
      .init : 0xc035b000 - 0xc0388000   ( 180 kB)
      .data : 0xc029989d - 0xc03553b8   ( 750 kB)
      .text : 0xc0100000 - 0xc029989d   (1638 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3461.31 BogoMIPS 
(lpj=1730655)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 8k freed
ACPI: Core revision 20060707
 tbxface-0107 [01] load_tables           : ACPI Tables successfully acquired
Parsing all Control Methods:
Table [DSDT](id 000A) - 649 Objects with 60 Devices 190 Methods 21 Regions
Parsing all Control Methods:
Table [SSDT](id 0004) - 10 Objects with 3 Devices 4 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0005) - 11 Objects with 3 Devices 5 Methods 0 Regions
Parsing all Control Methods:
hda: MATSHITAUJ-832D, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
st: Version 20061107, fixed bufsize 32768, s/g segs 256
SCSI Media Changer driver v0.25
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 18 (level, low) -> IRQ 19
ahci 0000:00:1f.2: PORTS_IMPL is zero, forcing 0xf
ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led pmp slum part
ata1: SATA max UDMA/133 cmd 0xE081C500 ctl 0x0 bmdma 0x0 irq 19
ata2: SATA max UDMA/133 cmd 0xE081C580 ctl 0x0 bmdma 0x0 irq 19
ata3: SATA max UDMA/133 cmd 0xE081C600 ctl 0x0 bmdma 0x0 irq 19
ata4: SATA max UDMA/133 cmd 0xE081C680 ctl 0x0 bmdma 0x0 irq 19
scsi0 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : ahci
ata2: SATA link down (SStatus 0 SControl 0)
scsi2 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
ata4: SATA link down (SStatus 0 SControl 0)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 0000 PQ: 0 ANSI: 5
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 180k freed
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
Synchronizing SCSI cache for disk sda:

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: ahci_softreset prevents acpi_power_off
  2007-01-11 10:31 Faik Uygur
@ 2007-01-13  1:12 ` Tejun Heo
  2007-01-13  5:59   ` Faik Uygur
  2007-01-13 12:10   ` Faik Uygur
  0 siblings, 2 replies; 13+ messages in thread
From: Tejun Heo @ 2007-01-13  1:12 UTC (permalink / raw)
  To: Faik Uygur; +Cc: linux-kernel, jgarzik, linux-ide

Hello,

Faik Uygur wrote:
> We have a Sony PCG-6H1M laptop. It started failing to poweroff with our switch 
> from 2.6.16 stable series kernels to 2.6.18 stable series. Rebooting works.
> 
> While searching for the cause, I have found these reported bug reports in the 
> kernel bugzilla which may be related to this bug:
> 
> http://bugzilla.kernel.org/show_bug.cgi?id=6982
> http://bugzilla.kernel.org/show_bug.cgi?id=7447

Seems mostly unrelated.

> According to git bisect, this is the first bad commit:
> 
> 4658f79bec0b51222e769e328c2923f39f3bda77 is first bad commit
> commit 4658f79bec0b51222e769e328c2923f39f3bda77
> Author: Tejun Heo <htejun@gmail.com>
> Date:   Wed Mar 22 21:07:03 2006 +0900
> 
>     [PATCH] ahci: add softreset
> 
>     Now that libata is smart enought to handle both soft and hard resets,
>     add softreset method.
> 
>     Signed-off-by: Tejun Heo <htejun@gmail.com>
>     Signed-off-by: Jeff Garzik <jeff@garzik.org>
> 
> :040000 040000 ba0a16d0ef82b6577bb61cfb18e6d9df9ee0984e 
> d0fc78d8f9bbe238f98ac8964562a33e64b30605 M      drivers
> 
> With v2.6.20-rc4 from git, it is still failing to poweroff. By not compiling 
> CONFIG_SCSI_SATA_AHCI, it successfully powers off.
> 
> Also with CONFIG_SCSI_SATA_AHCI, reverting this patch manually by setting 
> softreset to NULL in ata_do_eh calls in ahci.c makes the machine poweroff.

Wow, this is one of the most amazing error report.  ahci softreset
preventing system halt?

> I have attached the dmesg output with defined ATA_DEBUG, ATA_VERBOSE_DEBUG
> if it helps. Also you may find lspci output attached. 
> 
> Please let me know if anything else is needed.

Does everything else work okay?  Can you access devices attached to
ahci?  What happens when you try to shutdown?  If possible, please post
dmesg of shutting down.  You can store it easily using netconsole
(Documentation/networking/netconsole.txt).

Thanks.

-- 
tejun

^ permalink raw reply	[flat|nested] 13+ messages in thread

* ahci_softreset prevents acpi_power_off
@ 2007-01-11 10:31 Faik Uygur
  2007-01-13  1:12 ` Tejun Heo
  0 siblings, 1 reply; 13+ messages in thread
From: Faik Uygur @ 2007-01-11 10:31 UTC (permalink / raw)
  To: linux-kernel; +Cc: jgarzik, linux-ide

Hi,

We have a Sony PCG-6H1M laptop. It started failing to poweroff with our switch 
from 2.6.16 stable series kernels to 2.6.18 stable series. Rebooting works.

While searching for the cause, I have found these reported bug reports in the 
kernel bugzilla which may be related to this bug:

http://bugzilla.kernel.org/show_bug.cgi?id=6982
http://bugzilla.kernel.org/show_bug.cgi?id=7447

According to git bisect, this is the first bad commit:

4658f79bec0b51222e769e328c2923f39f3bda77 is first bad commit
commit 4658f79bec0b51222e769e328c2923f39f3bda77
Author: Tejun Heo <htejun@gmail.com>
Date:   Wed Mar 22 21:07:03 2006 +0900

    [PATCH] ahci: add softreset

    Now that libata is smart enought to handle both soft and hard resets,
    add softreset method.

    Signed-off-by: Tejun Heo <htejun@gmail.com>
    Signed-off-by: Jeff Garzik <jeff@garzik.org>

:040000 040000 ba0a16d0ef82b6577bb61cfb18e6d9df9ee0984e 
d0fc78d8f9bbe238f98ac8964562a33e64b30605 M      drivers

With v2.6.20-rc4 from git, it is still failing to poweroff. By not compiling 
CONFIG_SCSI_SATA_AHCI, it successfully powers off.

Also with CONFIG_SCSI_SATA_AHCI, reverting this patch manually by setting 
softreset to NULL in ata_do_eh calls in ahci.c makes the machine poweroff.

I have attached the dmesg output with defined ATA_DEBUG, ATA_VERBOSE_DEBUG
if it helps. Also you may find lspci output attached. 

Please let me know if anything else is needed.

Regards,
- Faik

Linux version 2.6.20-rc4 (root@pardus) (gcc version 3.4.6) #56 SMP Thu Jan 11 
11:38:37 EET 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 
000000000009f800 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 
00000000000a0000 type: 2
copy_e820_map() start: 00000000000d8000 size: 0000000000028000 end: 
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fd90000 end: 
000000001fe90000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001fe90000 size: 000000000000d000 end: 
000000001fe9d000 type: 3
copy_e820_map() start: 000000001fe9d000 size: 0000000000063000 end: 
000000001ff00000 type: 4
copy_e820_map() start: 000000001ff00000 size: 0000000000100000 end: 
0000000020000000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010006000 end: 
00000000f0006000 type: 2
copy_e820_map() start: 00000000f0008000 size: 0000000000004000 end: 
00000000f000c000 type: 2
copy_e820_map() start: 00000000fed20000 size: 0000000000070000 end: 
00000000fed90000 type: 2
copy_e820_map() start: 00000000ff000000 size: 0000000001000000 end: 
0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fe90000 (usable)
 BIOS-e820: 000000001fe90000 - 000000001fe9d000 (ACPI data)
 BIOS-e820: 000000001fe9d000 - 000000001ff00000 (ACPI NVS)
 BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
Entering add_active_range(0, 0, 130704) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   130704
  HighMem    130704 ->   130704
early_node_map[1] active PFN ranges
    0:        0 ->   130704
On node 0 totalpages: 130704
  DMA zone: 52 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4044 pages, LIFO batch:0
  Normal zone: 1607 pages used for memmap
  Normal zone: 125001 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6780
ACPI: RSDT (v001   Sony       V0 0x20051108 PTL  0x00000000) @ 0x1fe97449
ACPI: FADT (v002   Sony       V0 0x20051108 PTL  0x00000050) @ 0x1fe9ce78
ACPI: MADT (v001   Sony       V0 0x20051108 PTL  0x00000050) @ 0x1fe9cefc
ACPI: BOOT (v001   Sony       V0 0x20051108 PTL  0x00000001) @ 0x1fe9cfd8
ACPI: MCFG (v001   Sony       V0 0x20051108 PTL  0x0000005f) @ 0x1fe9cf9c
ACPI: SSDT (v001   Sony       V0 0x20051108 PTL  0x20030224) @ 0x1fe983aa
ACPI: SSDT (v001   Sony       V0 0x20051108 PTL  0x20030224) @ 0x1fe97d0e
ACPI: SSDT (v001   Sony       V0 0x20051108 PTL  0x20030224) @ 0x1fe978c9
ACPI: SSDT (v001   Sony       V0 0x20051108 PTL  0x20030224) @ 0x1fe976aa
ACPI: SSDT (v001   Sony       V0 0x20051108 PTL  0x20030224) @ 0x1fe97491
ACPI: DSDT (v001   Sony       V0 0x20051108 PTL  0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1729.210 MHz processor.
Built 1 zonelists.  Total pages: 129045
Kernel command line: root=/dev/sda1 mudur=language:tr init=/bin/bash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      16384
... CHAINHASH_SIZE:          8192
 memory used by lock dependency info: 1064 kB
 per task-struct memory footprint: 1200 bytes
------------------------
| Locking API testsuite:
----------------------------------------------------------------------------
                                 | spin |wlock |rlock |mutex | wsem | rsem |
  --------------------------------------------------------------------------
                     A-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                 A-B-B-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
             A-B-B-C-C-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
             A-B-C-A-B-C deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
         A-B-B-C-C-D-D-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
         A-B-C-D-B-D-D-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
         A-B-C-D-B-C-D-A deadlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                    double unlock:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                  initialize held:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
                 bad unlock order:  ok  |  ok  |  ok  |  ok  |  ok  |  ok  |
  --------------------------------------------------------------------------
              recursive read-lock:             |  ok  |             |  ok  |
           recursive read-lock #2:             |  ok  |             |  ok  |
            mixed read-write-lock:             |  ok  |             |  ok  |
            mixed write-read-lock:             |  ok  |             |  ok  |
  --------------------------------------------------------------------------
     hard-irqs-on + irq-safe-A/12:  ok  |  ok  |  ok  |
     soft-irqs-on + irq-safe-A/12:  ok  |  ok  |  ok  |
     hard-irqs-on + irq-safe-A/21:  ok  |  ok  |  ok  |
     soft-irqs-on + irq-safe-A/21:  ok  |  ok  |  ok  |
       sirq-safe-A => hirqs-on/12:  ok  |  ok  |  ok  |
       sirq-safe-A => hirqs-on/21:  ok  |  ok  |  ok  |
         hard-safe-A + irqs-on/12:  ok  |  ok  |  ok  |
         soft-safe-A + irqs-on/12:  ok  |  ok  |  ok  |
         hard-safe-A + irqs-on/21:  ok  |  ok  |  ok  |
         soft-safe-A + irqs-on/21:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/123:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/123:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/132:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/132:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/213:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/213:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/231:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/231:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/312:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/312:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #1/321:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #1/321:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/123:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/123:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/132:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/132:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/213:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/213:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/231:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/231:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/312:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/312:  ok  |  ok  |  ok  |
    hard-safe-A + unsafe-B #2/321:  ok  |  ok  |  ok  |
    soft-safe-A + unsafe-B #2/321:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/123:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/123:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/132:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/132:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/213:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/213:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/231:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/231:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/312:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/312:  ok  |  ok  |  ok  |
      hard-irq lock-inversion/321:  ok  |  ok  |  ok  |
      soft-irq lock-inversion/321:  ok  |  ok  |  ok  |
      hard-irq read-recursion/123:  ok  |
      soft-irq read-recursion/123:  ok  |
      hard-irq read-recursion/132:  ok  |
      soft-irq read-recursion/132:  ok  |
      hard-irq read-recursion/213:  ok  |
      soft-irq read-recursion/213:  ok  |
      hard-irq read-recursion/231:  ok  |
      soft-irq read-recursion/231:  ok  |
      hard-irq read-recursion/312:  ok  |
      soft-irq read-recursion/312:  ok  |
      hard-irq read-recursion/321:  ok  |
      soft-irq read-recursion/321:  ok  |
-------------------------------------------------------
Good, all 218 testcases passed! |
---------------------------------
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510364k/522816k available (1530k kernel code, 11928k reserved, 704k 
data, 172k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4f000 - 0xfffff000   ( 704 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdfe90000   ( 510 MB)
      .init : 0xc0334000 - 0xc035f000   ( 172 kB)
      .data : 0xc027eb6d - 0xc032ed18   ( 704 kB)
      .text : 0xc0100000 - 0xc027eb6d   (1530 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3461.30 BogoMIPS 
(lpj=1730652)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000180 
00000000 00000000
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 7k freed
ACPI: Core revision 20060707
 tbxface-0107 [01] load_tables           : ACPI Tables successfully acquired
Parsing all Control Methods:
Table [DSDT](id 000A) - 649 Objects with 60 Devices 190 Methods 21 Regions
Parsing all Control Methods:
Table [SSDT](id 0004) - 10 Objects with 3 Devices 4 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0005) - 11 Objects with 3 Devices 5 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0006) - 5 Objects with 0 Devices 3 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0007) - 1 Objects with 0 Devices 1 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0008) - 10 Objects with 0 Devices 2 Methods 0 Regions
ACPI Namespace successfully loaded at root c05a54b0
evxfevnt-0089 [02] enable                : Transition to ACPI mode successful
CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
Total of 1 processors activated (3461.30 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
evgpeblk-0951 [04] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 
0x9
evgpeblk-1048 [03] ev_initialize_gpe_bloc: Found 7 Wake, Enabled 2 Runtime 
GPEs in this block
Completing Region/Field/Buffer/Package 
initialization:.............................................................
Initialized 21/21 Regions 0/0 Fields 27/27 Buffers 13/21 Packages (695 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:..
Executed 2 _INI methods requiring 1 _STA executions (examined 71 objects)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:06:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) 
(try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs *10)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10)
ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *3
ACPI: PCI Interrupt Link [LNKG] (IRQs *10)
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
SCSI subsystem initialized
libata version 2.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: 90000000-afffffff
  PREFETCH window: c0000000-cfffffff
PCI: Bus 7, cardbus bridge: 0000:06:05.0
  IO window: 00002400-000024ff
  IO window: 00002800-000028ff
  PREFETCH window: 30000000-33ffffff
  MEM window: 34000000-37ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: b0000000-b00fffff
  PREFETCH window: 30000000-33ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 21 (level, low) -> IRQ 17
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 18 (level, low) -> IRQ 18
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: MATSHITAUJ-832D, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
st: Version 20061107, fixed bufsize 32768, s/g segs 256
SCSI Media Changer driver v0.25 
ahci_init_one: ENTER
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 18 (level, low) -> IRQ 18
ahci 0000:00:1f.2: PORTS_IMPL is zero, forcing 0xf
ahci_host_init: cap 0xc6127f03  port_map 0x5  n_ports 4
ahci_setup_port: ENTER, base==0xe081a400, port_idx 0
ahci_setup_port: base now==0xe081a500
ahci_setup_port: EXIT
ahci_setup_port: ENTER, base==0xe081a400, port_idx 1
ahci_setup_port: base now==0xe081a580
ahci_setup_port: EXIT
ahci_setup_port: ENTER, base==0xe081a400, port_idx 2
ahci_setup_port: base now==0xe081a600
ahci_setup_port: EXIT
ahci_setup_port: ENTER, base==0xe081a400, port_idx 3
ahci_setup_port: base now==0xe081a680
ahci_setup_port: EXIT
ahci_init_controller: PORT_SCR_ERR 0x4050000
ahci_init_controller: PORT_IRQ_STAT 0x0
ahci_init_controller: PORT_SCR_ERR 0x0
ahci_init_controller: PORT_IRQ_STAT 0x0
ahci_init_controller: PORT_SCR_ERR 0x0
ahci_init_controller: PORT_IRQ_STAT 0x0
ahci_init_controller: PORT_SCR_ERR 0x0
ahci_init_controller: PORT_IRQ_STAT 0x0
ahci_init_controller: HOST_CTL 0x80000000
ahci_init_controller: HOST_CTL 0x80000002
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led pmp slum part 
ata_device_add: ENTER
ata_port_add: ENTER
ata1: SATA max UDMA/133 cmd 0xE081A500 ctl 0x0 bmdma 0x0 irq 18
__ata_port_freeze: ata1 port frozen
ata_port_add: ENTER
ata2: SATA max UDMA/133 cmd 0xE081A580 ctl 0x0 bmdma 0x0 irq 18
__ata_port_freeze: ata2 port frozen
ata_port_add: ENTER
ata3: SATA max UDMA/133 cmd 0xE081A600 ctl 0x0 bmdma 0x0 irq 18
__ata_port_freeze: ata3 port frozen
ata_port_add: ENTER
ata4: SATA max UDMA/133 cmd 0xE081A680 ctl 0x0 bmdma 0x0 irq 18
__ata_port_freeze: ata4 port frozen
ata_device_add: probe begin
scsi0 : ahci
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata1: ata_port_flush_task: flush #2
ata1: ata_port_flush_task: EXIT
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata1 port frozen
ahci_softreset: ENTER
ata_dev_classify: found ATA device by sig
ahci_softreset: EXIT, class=1
ata_std_postreset: ENTER
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata_std_postreset: EXIT
ata_eh_thaw_port: ata1 port thawed
ata_eh_revalidate_and_attach: ENTER
ata1.00: ata_dev_read_id: ENTER, host 1, dev 0
ata1: ata_dev_select: ENTER, ata1: device 0, wait 1
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata1: ata_port_flush_task: flush #2
ata1: ata_port_flush_task: EXIT
ata1.00: ata_dev_configure: ENTER, host 1, dev 0
ata1.00: ata_dev_configure: cfg 49:2f00 82:346b 83:7f09 84:6063 85:3469 
86:bf09 87:6063 88:203f
ata_dump_id: 49==0x2f00  53==0x0007  63==0x0007  64==0x0003  75==0x001f  
ata_dump_id: 80==0x00f8  81==0x0021  82==0x346b  83==0x7f09  84==0x6063  
ata_dump_id: 88==0x203f  93==0x0000
ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: ata_dev_configure: EXIT, drv_stat = 0x50
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_dev_set_xfermode: set features - xfer mode
ahci_interrupt: ENTER
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata1: ata_port_flush_task: flush #2
ata1: ata_port_flush_task: EXIT
ata_dev_set_xfermode: EXIT, err_mask=0
ata1.00: ata_dev_read_id: ENTER, host 1, dev 0
ata1: ata_dev_select: ENTER, ata1: device 0, wait 1
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata1: ata_port_flush_task: flush #2
ata1: ata_port_flush_task: EXIT
ata1.00: ata_dev_configure: ENTER, host 1, dev 0
ata1.00: ata_dev_configure: cfg 49:2f00 82:346b 83:7f09 84:6063 85:3469 
86:bf09 87:6063 88:203f
ata_dump_id: 49==0x2f00  53==0x0007  63==0x0007  64==0x0003  75==0x001f  
ata_dump_id: 80==0x00f8  81==0x0021  82==0x346b  83==0x7f09  84==0x6063  
ata_dump_id: 88==0x203f  93==0x0000
ata1.00: ata_dev_configure: EXIT, drv_stat = 0x50
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x45
ata1.00: configured for UDMA/100
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
scsi1 : ahci
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata2: ata_port_flush_task: flush #2
ata2: ata_port_flush_task: EXIT
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata2 port frozen
ahci_softreset: ENTER
ahci_softreset: PHY reports no device
ata_std_postreset: ENTER
ata2: SATA link down (SStatus 0 SControl 0)
ata_std_postreset: EXIT, no device
ata_eh_thaw_port: ata2 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
scsi2 : ahci
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata3: ata_port_flush_task: flush #2
ata3: ata_port_flush_task: EXIT
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata3 port frozen
ahci_softreset: ENTER
ahci_softreset: PHY reports no device
ata_std_postreset: ENTER
ata3: SATA link down (SStatus 0 SControl 300)
ata_std_postreset: EXIT, no device
ata_eh_thaw_port: ata3 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
scsi3 : ahci
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata4: ata_port_flush_task: flush #2
ata4: ata_port_flush_task: EXIT
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata4 port frozen
ahci_softreset: ENTER
ahci_softreset: PHY reports no device
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 0)
ata_std_postreset: EXIT, no device
ata_eh_thaw_port: ata4 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_device_add: host probe begin
ata_scsi_dump_cdb: CDB (1:0,0,0) 12 00 00 00 24 00 00 00 cc
ata_scsiop_inq_std: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 12 00 00 00 60 00 00 00 cc
ata_scsiop_inq_std: ENTER
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 0000 PQ: 0 ANSI: 5
ata_scsi_dump_cdb: CDB (1:0,0,0) 00 00 00 00 00 00 00 00 cc
ata_scsiop_noop: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 3f 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 24
ata_scsiop_mode_sense: ENTER
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
ata_scsi_dump_cdb: CDB (1:0,0,0) 00 00 00 00 00 00 00 00 24
ata_scsiop_noop: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 3f 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 24
ata_scsiop_mode_sense: ENTER
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support 
DPO or FUA
 sda:<3>ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 00 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
 sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
ata_device_add: EXIT, returning 4
piix_init: pci_register_driver
piix_init: done
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 41 00 00 02
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 3f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 47 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 57 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 6f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 10 97 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 10 6f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 74 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 74 10 5f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 02 b4 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 02 b4 10 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 30 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 30 10 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 30 02 b7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c1 07 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 10 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 02 27 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 02 3f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 3a 1f 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c1 67 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c5 8f 00 00 90
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 18 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 18 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 3a 4f 00 00 38
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 7 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 7 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 3a 87 00 00 58
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 11 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 11 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 3a 3f 00 00 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 2 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 2 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 10 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c1 27 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c1 2f 00 00 38
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 7 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c1 6f 00 00 a0
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 20 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 7 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 20 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 05 1f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 62 80 5f 00 00 28
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 5 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 62 81 57 00 00 40
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 8 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 5 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 8 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 62 81 97 00 00 a0
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 20 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 20 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 02 17 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 6a 57 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 6a 77 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 6a 7f 00 00 40
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 8 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 8 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 6a bf 00 02 18
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 67 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 67 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 62 82 37 00 00 38
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 7 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 7 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 3c 37 00 00 18
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 3 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 3 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 79 57 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 79 77 00 00 28
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 5 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2e 57 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 5 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2e 77 00 04 00
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 128 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 32 77 00 02 a0
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 84 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 37 3f 00 02 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 66 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 128 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 84 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 66 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c4 b7 00 00 d8
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 27 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 27 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 e0 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 e0 10 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 74 10 6f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c2 f7 00 01 00
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 32 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 32 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c3 f7 00 00 b0
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 22 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 22 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c2 0f 00 00 c8
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 25 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 25 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 06 c7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 00 67 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 82 2f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 02 1f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 02 37 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2e 17 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2e 37 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 72 f7 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 73 17 00 00 18
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 3 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 1e 67 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 3 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2a f7 00 00 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 2 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 2 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2b 07 00 00 30
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 6 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 6 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 78 87 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1d 78 a7 00 00 28
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 5 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 5 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1c 02 2f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2d cf 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 2d ef 00 00 28
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 5 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 5 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 01 ff 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 62 c0 d7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c2 d7 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 01 b7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 31 5f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 31 97 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 31 9f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 44 03 37 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 46 40 6f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 00 af 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 12 df 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 31 c4 a7 00 00 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 2 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 2 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b0 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b0 10 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 d4 01 e7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 d4 c1 27 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 d4 01 ef 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 d4 c1 7f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 d4 c1 87 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b0 00 7f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b0 1f ef 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 3b 8f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b0 00 77 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b0 19 a7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b2 48 37 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b4 f1 0f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b4 f9 97 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 05 0f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 09 3f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 09 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 11 a7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 22 9f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b5 3f 27 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b8 76 37 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 01 b9 9e 5f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c1 d7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c1 e7 00 00 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 2 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c1 ff 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 2 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 07 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 17 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 27 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 57 00 00 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 2 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 2 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 67 00 00 18
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 3 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 3 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 29 67 00 00 20
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 4 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 4 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 29 87 00 00 18
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 3 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 3 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 1e 29 9f 00 00 18
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 3 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 3 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 01 cf 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 61 03 a7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 01 c7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 62 c0 3f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
ata_scsi_dump_cdb: CDB (1:0,0,0) 2a 00 00 00 00 3f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
EXT3 FS on sda1, internal journal
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 00 47 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 06 a7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 60 00 3f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 2a 00 00 00 10 97 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 2a 00 04 60 aa 87 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 2a 00 00 00 10 9f 00 00 48
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 9 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 9 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 2a 00 00 00 10 e7 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 04 32 c2 bf 00 00 10
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 2 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 2 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 84 00 47 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 84 00 4f 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT


00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express 
Processor to DRAM Controller (rev 03)
	Subsystem: Sony Corporation Unknown device 81b7
	Flags: bus master, fast devsel, latency 0
	Capabilities: [e0] Vendor Specific Information

00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root 
Port (rev 03) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: 90000000-afffffff
	Prefetchable memory behind bridge: c0000000-cfffffff
	Capabilities: [88] #0d [0000]
	Capabilities: [80] Power Management version 2
	Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
	Capabilities: [a0] Express Root Port (Slot+) IRQ 0
	Capabilities: [100] Virtual Channel
	Capabilities: [140] Unknown (5)

00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
High Definition Audio Controller (rev 03)
	Subsystem: Sony Corporation Unknown device 81cc
	Flags: bus master, fast devsel, latency 0, IRQ 10
	Memory at 80000000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
	Capabilities: [70] Express Unknown type IRQ 0
	Capabilities: [100] Virtual Channel
	Capabilities: [130] Unknown (5)

00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0, IRQ 217
	I/O ports at 1800 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0, IRQ 225
	I/O ports at 1820 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0, IRQ 177
	I/O ports at 1840 [size=32]

00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0, IRQ 217
	I/O ports at 1860 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0, IRQ 209
	Memory at 80004000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
	Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) 
(prog-if 01 [Subtractive decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=06, subordinate=0a, sec-latency=32
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: b0000000-b00fffff
	Prefetchable memory behind bridge: 0000000030000000-0000000031f00000
	Capabilities: [50] #0d [0000]

00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge 
(rev 03)
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0

00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) 
IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: bus master, medium devsel, latency 0, IRQ 201
	I/O ports at <unassigned>
	I/O ports at <unassigned>
	I/O ports at <unassigned>
	I/O ports at <unassigned>
	I/O ports at 1880 [size=16]

00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 
03) (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: Sony Corporation Unknown device 81ba
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 201
	I/O ports at 18c0 [size=8]
	I/O ports at 18b8 [size=4]
	I/O ports at 18b0 [size=8]
	I/O ports at 1894 [size=4]
	I/O ports at 18a0 [size=16]
	Memory at 80004400 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [70] Power Management version 2

00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus 
Controller (rev 03)
	Subsystem: Sony Corporation Unknown device 81b9
	Flags: medium devsel
	I/O ports at 18e0 [size=32]

01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce Go 6200 
TurboCache] (rev a1) (prog-if 00 [VGA])
	Subsystem: Sony Corporation Unknown device 81eb
	Flags: bus master, fast devsel, latency 0, IRQ 10
	Memory at a0000000 (32-bit, non-prefetchable) [size=16M]
	Memory at c0000000 (64-bit, prefetchable) [size=256M]
	Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
	[virtual] Expansion ROM at 91000000 [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
	Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
	Capabilities: [78] Express Endpoint IRQ 0
	Capabilities: [100] Virtual Channel
	Capabilities: [128] Power Budgeting

06:05.0 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
	Subsystem: Sony Corporation Unknown device 818f
	Flags: bus master, medium devsel, latency 168, IRQ 177
	Memory at b0008000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
	Memory window 0: 30000000-31fff000 (prefetchable)
	Memory window 1: 32000000-33fff000
	I/O window 0: 00002400-000024ff
	I/O window 1: 00002800-000028ff
	16-bit legacy interface ports at 0001

06:05.2 FireWire (IEEE 1394): Texas Instruments PCI7x20 1394a-2000 OHCI 
Two-Port PHY/Link-Layer Controller (prog-if 10 [OHCI])
	Subsystem: Sony Corporation Unknown device 818f
	Flags: bus master, medium devsel, latency 32, IRQ 233
	Memory at b0004000 (32-bit, non-prefetchable) [size=2K]
	Memory at b0000000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 2

06:05.3 Mass storage controller: Texas Instruments PCI7420/7620 Combo CardBus, 
1394a-2000 OHCI and SD/MS-Pro Controller
	Subsystem: Sony Corporation Unknown device 8190
	Flags: bus master, medium devsel, latency 57, IRQ 10
	Memory at b0005000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

06:08.0 Ethernet controller: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE 
(LOM) Ethernet Controller Mobile (rev 03)
	Subsystem: Sony Corporation Unknown device 81d0
	Flags: bus master, medium devsel, latency 66, IRQ 233
	Memory at b0006000 (32-bit, non-prefetchable) [size=4K]
	I/O ports at 2000 [size=64]
	Capabilities: [dc] Power Management version 2

06:0b.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network 
Connection (rev 05)
	Subsystem: Intel Corporation Unknown device 2753
	Flags: bus master, medium devsel, latency 32, IRQ 50
	Memory at b0007000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2


^ permalink raw reply	[flat|nested] 13+ messages in thread

end of thread, other threads:[~2007-01-15 13:55 UTC | newest]

Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <fa.enjQgtLFPdSkeJjKv6eOjULTovQ@ifi.uio.no>
     [not found] ` <fa.1s/e9SHVR6LQC2HgdZRykrqlV5Q@ifi.uio.no>
     [not found]   ` <fa.kpxGqupQMKJxBBFrktFUzuoKc7c@ifi.uio.no>
2007-01-14  1:23     ` ahci_softreset prevents acpi_power_off Robert Hancock
2007-01-14  3:18       ` Jeff Garzik
2007-01-14 17:50         ` Faik Uygur
2007-01-14 17:59       ` Faik Uygur
2007-01-14 18:06         ` Arjan van de Ven
2007-01-14 18:58           ` Faik Uygur
2007-01-15  4:02           ` Tejun Heo
2007-01-15 13:44             ` Jeff Garzik
2007-01-15 13:55               ` Tejun Heo
2007-01-11 10:31 Faik Uygur
2007-01-13  1:12 ` Tejun Heo
2007-01-13  5:59   ` Faik Uygur
2007-01-13 12:10   ` Faik Uygur

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).