LKML Archive on lore.kernel.org help / color / mirror / Atom feed
* USB extension (repeater) cable @ 2007-01-19 15:40 Udo van den Heuvel 2007-01-20 0:01 ` Greg KH 0 siblings, 1 reply; 6+ messages in thread From: Udo van den Heuvel @ 2007-01-19 15:40 UTC (permalink / raw) To: linux-kernel Hello, I just tried my shiny new usb extension cable (repeater): Jan 19 16:01:17 epia kernel: usb 5-1: new high speed USB device using ehci_hcd and address 60 Jan 19 16:01:17 epia kernel: usb 5-1: configuration #1 chosen from 1 choice Jan 19 16:01:17 epia kernel: hub 5-1:1.0: USB hub found Jan 19 16:01:17 epia kernel: hub 5-1:1.0: 4 ports detected Jan 19 16:01:18 epia kernel: hub 5-1:1.0: Cannot enable port 1. Maybe the USB cable is bad? Jan 19 16:01:22 epia last message repeated 3 times Jan 19 16:01:23 epia kernel: hub 5-1:1.0: Cannot enable port 2. Maybe the USB cable is bad? Jan 19 16:01:26 epia last message repeated 3 times Jan 19 16:01:27 epia kernel: hub 5-1:1.0: Cannot enable port 3. Maybe the USB cable is bad? Jan 19 16:01:31 epia last message repeated 3 times The second cable does the same. Of course we have just one port on this hub... Any ideas? ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: USB extension (repeater) cable 2007-01-19 15:40 USB extension (repeater) cable Udo van den Heuvel @ 2007-01-20 0:01 ` Greg KH 2007-01-21 7:18 ` H. Peter Anvin 0 siblings, 1 reply; 6+ messages in thread From: Greg KH @ 2007-01-20 0:01 UTC (permalink / raw) To: Udo van den Heuvel; +Cc: linux-kernel On Fri, Jan 19, 2007 at 04:40:34PM +0100, Udo van den Heuvel wrote: > Hello, > > I just tried my shiny new usb extension cable (repeater): > > Jan 19 16:01:17 epia kernel: usb 5-1: new high speed USB device using > ehci_hcd and address 60 > Jan 19 16:01:17 epia kernel: usb 5-1: configuration #1 chosen from 1 choice > Jan 19 16:01:17 epia kernel: hub 5-1:1.0: USB hub found > Jan 19 16:01:17 epia kernel: hub 5-1:1.0: 4 ports detected > Jan 19 16:01:18 epia kernel: hub 5-1:1.0: Cannot enable port 1. Maybe > the USB cable is bad? > Jan 19 16:01:22 epia last message repeated 3 times > Jan 19 16:01:23 epia kernel: hub 5-1:1.0: Cannot enable port 2. Maybe > the USB cable is bad? > Jan 19 16:01:26 epia last message repeated 3 times > Jan 19 16:01:27 epia kernel: hub 5-1:1.0: Cannot enable port 3. Maybe > the USB cable is bad? > Jan 19 16:01:31 epia last message repeated 3 times > > The second cable does the same. > Of course we have just one port on this hub... > Any ideas? Perhaps the kernel is not lying and this cable really is bad? :) Your hardware can not handle this device, there really is nothing that the kernel can do about this. USB extension cables are horrible things, and usually violate the USB spec and do not always work, as you are finding out. Sorry about that. good luck, greg k-h ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: USB extension (repeater) cable 2007-01-20 0:01 ` Greg KH @ 2007-01-21 7:18 ` H. Peter Anvin 2007-01-21 7:20 ` Udo van den Heuvel 0 siblings, 1 reply; 6+ messages in thread From: H. Peter Anvin @ 2007-01-21 7:18 UTC (permalink / raw) To: Greg KH; +Cc: Udo van den Heuvel, linux-kernel Greg KH wrote: > On Fri, Jan 19, 2007 at 04:40:34PM +0100, Udo van den Heuvel wrote: >> Hello, >> >> I just tried my shiny new usb extension cable (repeater): >> >> Jan 19 16:01:17 epia kernel: usb 5-1: new high speed USB device using >> ehci_hcd and address 60 >> Jan 19 16:01:17 epia kernel: usb 5-1: configuration #1 chosen from 1 choice >> Jan 19 16:01:17 epia kernel: hub 5-1:1.0: USB hub found >> Jan 19 16:01:17 epia kernel: hub 5-1:1.0: 4 ports detected >> Jan 19 16:01:18 epia kernel: hub 5-1:1.0: Cannot enable port 1. Maybe >> the USB cable is bad? >> Jan 19 16:01:22 epia last message repeated 3 times >> Jan 19 16:01:23 epia kernel: hub 5-1:1.0: Cannot enable port 2. Maybe >> the USB cable is bad? >> Jan 19 16:01:26 epia last message repeated 3 times >> Jan 19 16:01:27 epia kernel: hub 5-1:1.0: Cannot enable port 3. Maybe >> the USB cable is bad? >> Jan 19 16:01:31 epia last message repeated 3 times >> >> The second cable does the same. >> Of course we have just one port on this hub... >> Any ideas? > > Perhaps the kernel is not lying and this cable really is bad? :) > > Your hardware can not handle this device, there really is nothing that > the kernel can do about this. > > USB extension cables are horrible things, and usually violate the USB > spec and do not always work, as you are finding out. Sorry about that. > Actually, what it looks like is even simpler. The extension cable contains a four-port hub chip (which is the most common commodity chip) and haven't bothered changing the descriptor to tell the computer only one port is actually active. So only one port can be activated, and the others are stubbed out in some evil way. In that case, it should be noisy but harmless. -hpa ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: USB extension (repeater) cable 2007-01-21 7:18 ` H. Peter Anvin @ 2007-01-21 7:20 ` Udo van den Heuvel 2007-01-21 7:22 ` H. Peter Anvin 2007-01-21 23:08 ` Sven-Haegar Koch 0 siblings, 2 replies; 6+ messages in thread From: Udo van den Heuvel @ 2007-01-21 7:20 UTC (permalink / raw) To: linux-kernel; +Cc: H. Peter Anvin, Greg KH H. Peter Anvin wrote: > Greg KH wrote: >> On Fri, Jan 19, 2007 at 04:40:34PM +0100, Udo van den Heuvel wrote: >>> >>> I just tried my shiny new usb extension cable (repeater): >>> >>> Jan 19 16:01:17 epia kernel: usb 5-1: new high speed USB device using >>> ehci_hcd and address 60 >>> Jan 19 16:01:17 epia kernel: usb 5-1: configuration #1 chosen from 1 >>> choice >>> Jan 19 16:01:17 epia kernel: hub 5-1:1.0: USB hub found >>> Jan 19 16:01:17 epia kernel: hub 5-1:1.0: 4 ports detected >>> Jan 19 16:01:18 epia kernel: hub 5-1:1.0: Cannot enable port 1. Maybe >>> the USB cable is bad? >>> Jan 19 16:01:22 epia last message repeated 3 times >>> Jan 19 16:01:23 epia kernel: hub 5-1:1.0: Cannot enable port 2. Maybe >>> the USB cable is bad? >>> Jan 19 16:01:26 epia last message repeated 3 times >>> Jan 19 16:01:27 epia kernel: hub 5-1:1.0: Cannot enable port 3. Maybe >>> the USB cable is bad? >>> Jan 19 16:01:31 epia last message repeated 3 times [...] > Actually, what it looks like is even simpler. The extension cable > contains a four-port hub chip (which is the most common commodity chip) > and haven't bothered changing the descriptor to tell the computer only > one port is actually active. So only one port can be activated, and the > others are stubbed out in some evil way. In that case, it should be > noisy but harmless. I will do some more testing then. Is there a way to get rid of the messages? ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: USB extension (repeater) cable 2007-01-21 7:20 ` Udo van den Heuvel @ 2007-01-21 7:22 ` H. Peter Anvin 2007-01-21 23:08 ` Sven-Haegar Koch 1 sibling, 0 replies; 6+ messages in thread From: H. Peter Anvin @ 2007-01-21 7:22 UTC (permalink / raw) To: Udo van den Heuvel; +Cc: linux-kernel, Greg KH Udo van den Heuvel wrote: > >> Actually, what it looks like is even simpler. The extension cable >> contains a four-port hub chip (which is the most common commodity chip) >> and haven't bothered changing the descriptor to tell the computer only >> one port is actually active. So only one port can be activated, and the >> others are stubbed out in some evil way. In that case, it should be >> noisy but harmless. > > I will do some more testing then. > Is there a way to get rid of the messages? No, but you don't have to care about them. -hpa ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: USB extension (repeater) cable 2007-01-21 7:20 ` Udo van den Heuvel 2007-01-21 7:22 ` H. Peter Anvin @ 2007-01-21 23:08 ` Sven-Haegar Koch 1 sibling, 0 replies; 6+ messages in thread From: Sven-Haegar Koch @ 2007-01-21 23:08 UTC (permalink / raw) To: Udo van den Heuvel; +Cc: linux-kernel, H. Peter Anvin, Greg KH On Sun, 21 Jan 2007, Udo van den Heuvel wrote: > H. Peter Anvin wrote: >> Greg KH wrote: >>> On Fri, Jan 19, 2007 at 04:40:34PM +0100, Udo van den Heuvel wrote: >>>> >>>> I just tried my shiny new usb extension cable (repeater): >>>> >>>> Jan 19 16:01:17 epia kernel: usb 5-1: new high speed USB device using >>>> ehci_hcd and address 60 >>>> Jan 19 16:01:17 epia kernel: usb 5-1: configuration #1 chosen from 1 >>>> choice >>>> Jan 19 16:01:17 epia kernel: hub 5-1:1.0: USB hub found >>>> Jan 19 16:01:17 epia kernel: hub 5-1:1.0: 4 ports detected >>>> Jan 19 16:01:18 epia kernel: hub 5-1:1.0: Cannot enable port 1. Maybe >>>> the USB cable is bad? >>>> Jan 19 16:01:22 epia last message repeated 3 times >>>> Jan 19 16:01:23 epia kernel: hub 5-1:1.0: Cannot enable port 2. Maybe >>>> the USB cable is bad? >>>> Jan 19 16:01:26 epia last message repeated 3 times >>>> Jan 19 16:01:27 epia kernel: hub 5-1:1.0: Cannot enable port 3. Maybe >>>> the USB cable is bad? >>>> Jan 19 16:01:31 epia last message repeated 3 times > > [...] > >> Actually, what it looks like is even simpler. The extension cable >> contains a four-port hub chip (which is the most common commodity chip) >> and haven't bothered changing the descriptor to tell the computer only >> one port is actually active. So only one port can be activated, and the >> others are stubbed out in some evil way. In that case, it should be >> noisy but harmless. > > I will do some more testing then. > Is there a way to get rid of the messages? I am using the following patch (with 2.6.17) to shut up these messages with my repeater cable - found it on the linux-usb mailinglist some time ago when facing the same problem, but did not write down from who it is. (Does not silence all log messages when usb debugging is enabled, but when it is disabled there is no endless log-stream anymore and the cable works) I tried to fix the logging-change to the usb id, but the cable uses exactly the same chip and id as the two chips inside my 7port usb-hub. Index: linux/drivers/usb/core/hub.c =================================================================== --- linux.orig/drivers/usb/core/hub.c 2006-10-14 00:45:50.000000000 +0200 +++ linux/drivers/usb/core/hub.c 2006-10-14 00:47:38.000000000 +0200 @@ -1496,7 +1496,8 @@ /* bomb out completely if something weird happened */ if ((portchange & USB_PORT_STAT_C_CONNECTION)) - return -EINVAL; + //return -EINVAL; + return -ENOTCONN; /* if we`ve finished resetting, then break out of the loop */ if (!(portstatus & USB_PORT_STAT_RESET) && c'ya sven -- The Internet treats censorship as a routing problem, and routes around it. (John Gilmore on http://www.cygnus.com/~gnu/) ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2007-01-21 23:08 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2007-01-19 15:40 USB extension (repeater) cable Udo van den Heuvel 2007-01-20 0:01 ` Greg KH 2007-01-21 7:18 ` H. Peter Anvin 2007-01-21 7:20 ` Udo van den Heuvel 2007-01-21 7:22 ` H. Peter Anvin 2007-01-21 23:08 ` Sven-Haegar Koch
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).