LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
To: linux-kernel@vger.kernel.org
Subject: RE: [PATCH] serial driver PMC MSP71xx, kernel linux-mips.git mast er
Date: Mon, 22 Jan 2007 12:34:08 -0800	[thread overview]
Message-ID: <45B51FC0.60701@pmc-sierra.com> (raw)

CCing to linux-kernel as per AC's suggestion...

-------- Original Message --------
Subject: RE: [PATCH] serial driver PMC MSP71xx, kernel linux-mips.git master
Date: Mon, 22 Jan 2007 10:11:04 -0800
From: Marc St-Jean
To: Sergei Shtylyov
CC: <linux-mips@linux-mips.org>,	<linux-serial@vger.kernel.org>

> -----Original Message-----
> From: Sergei Shtylyov [mailto:sshtylyov@ru.mvista.com] 
> Sent: Friday, January 19, 2007 9:05 AM
> To: Marc St-Jean
> Cc: linux-mips@linux-mips.org; linux-serial@vger.kernel.org
> Subject: Re: [PATCH] serial driver PMC MSP71xx, kernel 
> linux-mips.git master
> 
> Hello.
> 
> Marc St-Jean wrote:
> > Here is a serial driver patch for the PMC-Sierra MSP71xx device.
> 
> > There are three different fixes:
> > 1. Fix for THRE errata
> > 2. Fix for Busy Detect on LCR write
> > 3. Workaround for interrupt/data concurrency issue
> 
> > The first fix is handled cleanly using a UART_BUG_* flag.
> 
>     Hm, I wouldn't call it clean...

Relative to the other two. Any recommended improvements on this one?


> > The second and third fixes use platform tests. I couldn't 
> think of a 
> > good way to implement them without using tests and not 
> increase code 
> > and structure sizes for platforms not requiring them.
> 
> > Does anyone have any suggestions on implementing these without the 
> > platform flag?
> 
> > Thanks,
> > Marc
> 
> > Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
> 
> > Index: linux_2_6/drivers/serial/8250.c 
> > ===================================================================
> > RCS file: linux_2_6/drivers/serial/8250.c,v retrieving revision 
> > 1.1.1.7 retrieving revision 1.9 diff -u -r1.1.1.7 -r1.9
> > --- linux_2_6/drivers/serial/8250.c	19 Oct 2006 21:00:58 
> -0000	1.1.1.7
> > +++ linux_2_6/drivers/serial/8250.c	19 Oct 2006 22:08:15 
> -0000	1.9
> > @@ -44,6 +44,10 @@
> >   #include <asm/io.h>
> >   #include <asm/irq.h>
> > 
> > +#ifdef CONFIG_PMC_MSP
> > +#include <msp_regs.h>
> > +#endif
> > +
> >   #include "8250.h"
> > 
> >   /*
> > @@ -130,6 +134,9 @@
> >   	unsigned char		mcr_mask;	/* mask of user bits */
> >   	unsigned char		mcr_force;	/* mask of 
> forced bits */
> >   	unsigned char		lsr_break_flag;
> > +#ifdef CONFIG_PMC_MSP
> > +	int					dwapb_lcr;	
> /* saved LCR for DW APB WAR */
> > +#endif
> 
>     There was already 'lcr' field there, couldn't it be used?

Possibly but the current driver doesn't always save the LCR value before
trying to write it. For example see serial8250_set_termios()
	serial_outp(up, UART_LCR, cval);		/* reset DLAB */
	up->lcr = cval;					/* Save LCR */

It's impossible to ensure that going foward the driver will always save
the value before writing it. We need to have it saved before since the
write will cause an interrupt, hence the save in serial_out.

If that's not acceptable I can audit the driver and ensure all LCR
writes are first saved. Maybe comments would reduce the chance of future
updates breaking this?


> > @@ -333,6 +340,10 @@
> >   static void
> >   serial_out(struct uart_8250_port *up, int offset, int value)
> >   {
> > +#ifdef CONFIG_PMC_MSP
> > +	/* Save the offset before it's remapped */
> > +	int dwapb_offset = offset;
> > +#endif
> >   	offset = map_8250_out_reg(up, offset) << up->port.regshift;
> > 
> >   	switch (up->port.iotype) {
> > @@ -342,7 +353,19 @@
> >   		break;
> > 
> >   	case UPIO_MEM:
> > +#ifdef CONFIG_PMC_MSP
> > +		/* Save the LCR value so it can be re-written when a
> > +		 * Busy Detect interrupt occurs. */
> > +		if (dwapb_offset == UART_LCR)
> > +			up->dwapb_lcr = value;
> > +#endif
> >   		writeb(value, up->port.membase + offset);
> > +#ifdef CONFIG_PMC_MSP
> > +		/* Re-read the IER to ensure any interrupt disabling has
> > +		 * completed before proceeding with ISR. */
> > +		if (dwapb_offset == UART_IER)
> > +			value = serial_in(up, dwapb_offset); #endif
> >   		break;
> 
>     Hm, was there really a need for #ifdef mess here?
>     I'd vote for introducing new UPIO_* here, like was done 
> for TSi10x UARTs just for the same reason.

I'm willing to do this, however IIRC there was a thread in late Sept.
which came to the conclusion that UPIO were to be used for different
access methods and not UART types. Do you see this as an exception?

In the second #ifdef CONFIG_PMC_MSP above the workaround is required
because of SoC interrupt design which is out-of-band with respect to r/w
of UART registers, it's not specific to the DesignWare UART.


> 
> > @@ -1016,6 +1039,17 @@
> >   		up->bugs |= UART_BUG_NOMSR;
> >   #endif
> > 
> > +	/* Workaround:
> > +	 * The DesignWare SoC UART part has a bug for all
> > +	 * versions before 3.03a (2005-07-18)
> > +	 * In brief, this is a non-standard 16550 in that the 
> THRE interrupt
> > +	 * will not re-assert itself simply by disabling and 
> re-enabling the
> > +	 * THRI bit in the IER, it is only re-enabled if a 
> character is actually
> > +	 * sent out.
> > +	 */
> > +	if( up->port.flags & UPF_DW_THRE_BUG )
> > +		up->bugs |= UART_BUG_DWTHRE;
> > +
> >   	serial_outp(up, UART_LCR, save_lcr);
> > 
> >   	if (up->capabilities != uart_config[up->port.type].flags) { @@ 
> > -1141,6 +1175,12 @@
> >   			iir = serial_in(up, UART_IIR);
> >   			if (lsr & UART_LSR_TEMT && iir & 
> UART_IIR_NO_INT)
> >   				transmit_chars(up);
> > +		} else if (up->bugs & UART_BUG_DWTHRE) {
> > +			unsigned char lsr, iir;
> > +			lsr = serial_in(up, UART_LSR);
> > +			iir = serial_in(up, UART_IIR);
> > +			if (lsr & UART_LSR_THRE)
> > +				transmit_chars(up);
> 
>     I don't see how this *really* differs from the UART_BUG_TXEN case.
>     Have you tried *that* workaround? 

I didn't write the code so I haven't tried it personally but I believe
it was investigated.

It looks like the results of the bugs are similar but the causes are
different. In the UART_BUG_TXEN case, if I understand the comment
correctly, NO interrupt is generated on enabling THRI. This is verified
by looking for Transmitter Empty (0x40) and no interrupt.

In the UART_BUG_DWTHRE case an interrupt IS generated on enabling THRI.
However no new THRE interupts will occur until a new character is
written to the THR and it's sent. This is verified by looking for
Transmit-Hold-Register Empty (0x20).


>	In any case, looks like this errata is auto-detectable just like
UART_BUG_TXEN.

I don't know how we would be able to test this without sending junk test
characters to the console port. We currently enable the bug flag in our
platform setup code when we know the bug is present from the SoC
version. Is that not acceptable?


> > @@ -1366,6 +1406,31 @@
> >   			handled = 1;
> > 
> >   			end = NULL;
> > +#ifdef CONFIG_PMC_MSP
> > +		} else if ((iir & UART_IER_BUSY) == UART_IER_BUSY) {
> 
>     Hm, masking IIR with IER mask, is this correct? Doubt it.


I agree, that was badly named. I've changed it to UART_IIR_BUSY for the
next spin.


> > +			/*
> > +			 * The MSP (DesignWare APB UART) serial 
> subsystem has a
> > +			 * non-standard interrupt condition 
> (0x7) which means
> > +			 * that the LCR was written while the 
> UART was busy, so
> > +			 * the LCR was not actually written.  
> It is cleared by
> > +			 * reading the special non-standard 
> extended UART status
> > +			 * register.
> > +			 */
> > +			unsigned int tmp;
> > +			if( up->port.line == 0 )
> > +				tmp = *UART0_STATUS_REG;
> > +			else
> > +				tmp = *UART1_STATUS_REG;
> > +			
> > +			/* Check if saved on LCR write */
> > +			if( up->dwapb_lcr != -1 )
> > +				serial_outp(up, UART_LCR, 
> up->dwapb_lcr);
> > +			else
> > +				printk(KERN_ERR "serial8250: 
> UART BUSY, no LCR write!\n" );
> > +
> > +			handled = 1;
> > +			end = NULL;
> > +#endif
> 
>     Not sure if this also shouldn't be handled in other 
> places which check for interrupt status, like serial8250_timeout()...

I can move the code to a function but I still see two issues:
A) We could move the code the a new function. We could also check for a
new UART_BUG_* flag before calling the function, but in reality this is
a feature of the UART not a bug.
B) How to eliminate the platform #ifdef. How to pass in the address of
the UARTx_STATUS_REG in a platform independent way?
We could add it to one of the data structures like uart_port, but it
would need an #ifdef in the header file.


> [...]
> > Index: linux_2_6/drivers/serial/8250.h 
> > ===================================================================
> > RCS file: linux_2_6/drivers/serial/8250.h,v retrieving revision 
> > 1.1.1.6 retrieving revision 1.4 diff -u -r1.1.1.6 -r1.4
> > --- linux_2_6/drivers/serial/8250.h	19 Oct 2006 21:00:58 
> -0000	1.1.1.6
> > +++ linux_2_6/drivers/serial/8250.h	19 Oct 2006 22:08:15 
> -0000	1.4
> > @@ -49,6 +49,7 @@
> >   #define UART_BUG_QUOT	(1 << 0)	/* UART has 
> buggy quot LSB */
> >   #define UART_BUG_TXEN	(1 << 1)	/* UART has 
> buggy TX IIR status */
> >   #define UART_BUG_NOMSR	(1 << 2)	/* UART has 
> buggy MSR status bits (Au1x00) */
> > +#define UART_BUG_DWTHRE (1 << 3)	/* UART has buggy 
> DesignWare THRE interrupt re-assertion */
> > 
> >   #define PROBE_RSA	(1 << 0)
> >   #define PROBE_ANY	(~0)
> > Index: linux_2_6/include/linux/serial_core.h
> > ===================================================================
> > RCS file: linux_2_6/include/linux/serial_core.h,v
> > retrieving revision 1.1.1.7
> > retrieving revision 1.5
> > diff -u -r1.1.1.7 -r1.5
> > --- linux_2_6/include/linux/serial_core.h	19 Oct 2006 
> 21:01:02 -0000	1.1.1.7
> > +++ linux_2_6/include/linux/serial_core.h	19 Oct 2006 
> 22:08:16 -0000	1.5
> > @@ -258,6 +258,8 @@
> >   #define UPF_CONS_FLOW		((__force upf_t) (1 << 23))
> >   #define UPF_SHARE_IRQ		((__force upf_t) (1 << 24))
> >   #define UPF_BOOT_AUTOCONF	((__force upf_t) (1 << 28))
> > +#define UPF_DW_THRE_BUG		((__force upf_t)(1 << 
> 29)) /* DesignWare THRE hardware BUG
> 
>     The need for the new flag seems doubtful to me.

Please see my earlier comment on this issue being different than
UART_BUG_TXEN.


> > +								
> 						* (cannot be 
> autodetected) */
> 
>     The patch is linewrapped
> 
> > Index: linux_2_6/include/linux/serial_reg.h
> > ===================================================================
> > RCS file: linux_2_6/include/linux/serial_reg.h,v
> > retrieving revision 1.1.1.2
> > retrieving revision 1.3
> > diff -u -r1.1.1.2 -r1.3
> > --- linux_2_6/include/linux/serial_reg.h	19 Oct 2006 
> 18:29:50 -0000	1.1.1.2
> > +++ linux_2_6/include/linux/serial_reg.h	19 Oct 2006 
> 19:45:04 -0000	1.3
> > @@ -218,6 +218,10 @@
> >   #define UART_FCR_PXAR16	0x80	/* receive FIFO treshold = 16 */
> >   #define UART_FCR_PXAR32	0xc0	/* receive FIFO treshold = 32 */
> > 
> > +/*
> > + * DesignWare APB UART
> > + */
> > +#define UART_IER_BUSY		0x07	/* Busy Detect */
> 
>     Are you sure it's not *IIR* value?  Doesn't look like 
> interrupt mask for IER. And IIR value of 7 already means 
> something else, namely, no interrupt and receiver status. Hm...

As mentioned earlier I have now renamed this UART_IIR_BUSY.

 From serial_reg.h, the receiver status is 0x06 and no interrupt is 0x01.
I thought these couldn't both be set at the same time? In any case this
is how DesignWare implemented the status so we can't change it now.

Thanks for the feedback,
Marc

             reply	other threads:[~2007-01-22 20:34 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-01-22 20:34 Marc St-Jean [this message]
  -- strict thread matches above, loose matches on Subject: below --
2007-02-16 17:06 Marc St-Jean
2007-02-16 17:21 ` Sergei Shtylyov
2007-02-16 16:30 Marc St-Jean
2007-02-13 22:11 Marc St-Jean
2007-02-12 17:46 Marc St-Jean
2007-02-12 17:56 ` Sergei Shtylyov
2007-02-09 19:39 Marc St-Jean
2007-02-10 17:30 ` Sergei Shtylyov
2007-02-07 20:50 Marc St-Jean
2007-02-06 16:52 Marc St-Jean
2007-01-27  0:28 Marc St-Jean
2007-01-25 23:10 Marc St-Jean
2007-01-26 13:58 ` Sergei Shtylyov
2007-01-24 21:10 Marc St-Jean
2007-01-25 14:29 ` Sergei Shtylyov
2007-01-24 16:48 Marc St-Jean
2007-01-24 20:38 ` Sergei Shtylyov
2007-01-24 16:40 Marc St-Jean
2007-01-24 19:40 ` Sergei Shtylyov
2007-01-23 22:37 Marc St-Jean
2007-01-23 23:41 ` Alan
2007-01-24 15:33 ` Sergei Shtylyov
2007-01-22 20:35 Marc St-Jean
2007-01-22 19:07 Marc St-Jean

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=45B51FC0.60701@pmc-sierra.com \
    --to=marc_st-jean@pmc-sierra.com \
    --cc=linux-kernel@vger.kernel.org \
    --subject='RE: [PATCH] serial driver PMC MSP71xx, kernel linux-mips.git mast er' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).