LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
To: Alan <alan@lxorguk.ukuu.org.uk>
Cc: linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org,
	linux-mips@linux-mips.org
Subject: Re: [PATCH] serial driver PMC MSP71xx, kernel linux-mips.git mast er
Date: Tue, 23 Jan 2007 14:37:23 -0800	[thread overview]
Message-ID: <45B68E23.7080800@pmc-sierra.com> (raw)


Alan wrote:
>  > There are three different fixes:
>  > 1. Fix for THRE errata
> 
> That should be handled anyway. The current code actually spots this and
> uses a backup timer for dodgy UARTS

Thanks, I'll retest without this fix on the current l-m.o git master and see
if it still solves our errata.

>  > 2. Fix for Busy Detect on LCR write
>  > 3. Workaround for interrupt/data concurrency issue
> 
>  >       case UPIO_MEM:
>  > +#ifdef CONFIG_PMC_MSP
>  > +             /* Save the LCR value so it can be re-written when a
>  > +              * Busy Detect interrupt occurs. */
>  > +             if (dwapb_offset == UART_LCR)
>  > +                     up->dwapb_lcr = value;
>  > +#endif
>  >               writeb(value, up->port.membase + offset);
>  > +#ifdef CONFIG_PMC_MSP
>  > +             /* Re-read the IER to ensure any interrupt disabling has
>  > +              * completed before proceeding with ISR. */
>  > +             if (dwapb_offset == UART_IER)
>  > +                     value = serial_in(up, dwapb_offset);
>  > +#endif
>  >               break;
> 
> This I would hope you can hide in the platform specific
> serial_in/serial_out functions. If you write the UART_LCR save it in
> serial_out(), if you read IER etc.

I couldn't find hooks for platform specific serial_in/out functions.
Do you mean using the up->port.iotype's in serial_in/out from 8250.c?

> 
>  > +#ifdef CONFIG_PMC_MSP
>  > +             } else if ((iir & UART_IER_BUSY) == UART_IER_BUSY) {
>  > +                     /*
>  > +                      * The MSP (DesignWare APB UART) serial 
> subsystem has a
>  > +                      * non-standard interrupt condition (0x7) which 
> means
>  > +                      * that the LCR was written while the UART was 
> busy, so
>  > +                      * the LCR was not actually written.  It is 
> cleared by
>  > +                      * reading the special non-standard extended 
> UART status
>  > +                      * register.
> 
> Ditto... spot this case and whack it in your serial methods.

A serial_in(up, UART_IIR) calls occur in more places that just the interrupt
handler (i.e. autoconfig*, serial8250_start_tx, etc). We will need to check
if we are in an interrupt on each IIR read, hopefully that won't be too much
overhead!

> 
> And we might want to add a void * for board specific insanity to the 8250
> structures if we really have to so you can hang your brain damage
> privately off that ?

Sounds good to me, it would give us a location to store the address of the
UART_STATUS_REG required by this UART variant.

Marc

             reply	other threads:[~2007-01-23 22:37 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-01-23 22:37 Marc St-Jean [this message]
2007-01-23 23:41 ` Alan
2007-01-24 15:33 ` Sergei Shtylyov
  -- strict thread matches above, loose matches on Subject: below --
2007-02-16 17:06 Marc St-Jean
2007-02-16 17:21 ` Sergei Shtylyov
2007-02-16 16:30 Marc St-Jean
2007-02-13 22:11 Marc St-Jean
2007-02-12 17:46 Marc St-Jean
2007-02-12 17:56 ` Sergei Shtylyov
2007-02-09 19:39 Marc St-Jean
2007-02-10 17:30 ` Sergei Shtylyov
2007-02-07 20:50 Marc St-Jean
2007-02-06 16:52 Marc St-Jean
2007-01-27  0:28 Marc St-Jean
2007-01-25 23:10 Marc St-Jean
2007-01-26 13:58 ` Sergei Shtylyov
2007-01-24 21:10 Marc St-Jean
2007-01-25 14:29 ` Sergei Shtylyov
2007-01-24 16:48 Marc St-Jean
2007-01-24 20:38 ` Sergei Shtylyov
2007-01-24 16:40 Marc St-Jean
2007-01-24 19:40 ` Sergei Shtylyov
2007-01-22 20:35 Marc St-Jean
2007-01-22 20:34 Marc St-Jean
2007-01-22 19:07 Marc St-Jean

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=45B68E23.7080800@pmc-sierra.com \
    --to=marc_st-jean@pmc-sierra.com \
    --cc=alan@lxorguk.ukuu.org.uk \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mips@linux-mips.org \
    --cc=linux-serial@vger.kernel.org \
    --subject='Re: [PATCH] serial driver PMC MSP71xx, kernel linux-mips.git mast er' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).