RE: [RFC net-next 4/5] net: phy: Add support for IEEE standard test modes

[<Woojung.Huh@microchip.com>]

Hi Florian,

> diff --git a/drivers/net/phy/phy-tests.c b/drivers/net/phy/phy-tests.c
...
> +/* genphy_set_test - Make a PHY enter one of the standard IEEE defined
> + * test modes
> + * @phydev: the PHY device instance
> + * @test: the desired test mode
> + * @data: test specific data (none)
> + *
> + * This function makes the designated @phydev enter the desired standard
> + * 100BaseT2 or 1000BaseT test mode as defined in IEEE 802.3-2012 section TWO
> + * and THREE under 32.6.1.2.1 and 40.6.1.1.2 respectively
> + */
> +int genphy_set_test(struct phy_device *phydev,
> +		    struct ethtool_phy_test *test, const u8 *data)
> +{
> +	u16 shift, base, bmcr = 0;
> +	int ret;
> +
> +	/* Exit test mode */
> +	if (test->mode == PHY_STD_TEST_MODE_NORMAL) {
> +		ret = phy_read(phydev, MII_CTRL1000);
> +		if (ret < 0)
> +			return ret;
> +
> +		ret &= ~GENMASK(15, 13);
> +
> +		return phy_write(phydev, MII_CTRL1000, ret);
> +	}
> +
> +	switch (test->mode) {
> +	case PHY_STD_TEST_MODE_100BASET2_1:
> +	case PHY_STD_TEST_MODE_100BASET2_2:
> +	case PHY_STD_TEST_MODE_100BASET2_3:
> +		if (!(phydev->supported & PHY_100BT_FEATURES))
> +			return -EOPNOTSUPP;
> +
> +		shift = 14;
> +		base = test->mode - PHY_STD_TEST_MODE_NORMAL;
> +		bmcr = BMCR_SPEED100;
> +		break;
> +
> +	case PHY_STD_TEST_MODE_1000BASET_1:
> +	case PHY_STD_TEST_MODE_1000BASET_2:
> +	case PHY_STD_TEST_MODE_1000BASET_3:
> +	case PHY_STD_TEST_MODE_1000BASET_4:
> +		if (!(phydev->supported & PHY_1000BT_FEATURES))
> +			return -EOPNOTSUPP;
> +
> +		shift = 13;
> +		base = test->mode - PHY_STD_TEST_MODE_100BASET2_MAX;
> +		bmcr = BMCR_SPEED1000;
> +		break;
> +
> +	default:
> +		/* Let an upper driver deal with additional modes it may
> +		 * support
> +		 */
> +		return -EOPNOTSUPP;
> +	}
> +
> +	/* Force speed and duplex */
> +	ret = phy_write(phydev, MII_BMCR, bmcr | BMCR_FULLDPLX);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Set the desired test mode bit */
> +	return phy_write(phydev, MII_CTRL1000, (test->mode + base) << shift);
> +}
For now, these are for 100B-T2 & 1000B-TX.
But, other speeds such as 802.3bw/bq/cq have very similar format,
how about make  phy_write() to BMCR & CTRL1000 as another function call per speed?

Thanks.
Woojung