LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Linu Cherian <linuc.decode@gmail.com>
To: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
Mark Rutland <mark.rutland@arm.com>,
maz@kernel.org, Anshuman Khandual <anshuman.khandual@arm.com>,
catalin.marinas@arm.com,
Coresight ML <coresight@lists.linaro.org>,
linux-kernel@vger.kernel.org, james.morse@arm.com,
Will Deacon <will@kernel.org>, Mike Leach <mike.leach@linaro.org>
Subject: Re: [PATCH 08/10] coresight: trbe: Workaround TRBE errat overwrite in FILL mode
Date: Fri, 6 Aug 2021 21:39:43 +0530 [thread overview]
Message-ID: <CAAHhmWjR6XYo5j_h3jfLsmWzqD9i9L-pHq=zrrdrw9YTXmuCqg@mail.gmail.com> (raw)
In-Reply-To: <20210728135217.591173-9-suzuki.poulose@arm.com>
Hi Suzuki,
On Wed, Jul 28, 2021 at 7:23 PM Suzuki K Poulose <suzuki.poulose@arm.com> wrote:
>
> ARM Neoverse-N2 (#2139208) and Cortex-A710(##2119858) suffers from
> an erratum, which when triggered, might cause the TRBE to overwrite
> the trace data already collected in FILL mode, in the event of a WRAP.
> i.e, the TRBE doesn't stop writing the data, instead wraps to the base
> and could write upto 3 cache line size worth trace. Thus, this could
> corrupt the trace at the "BASE" pointer.
>
> The workaround is to program the write pointer 256bytes from the
> base, such that if the erratum is triggered, it doesn't overwrite
> the trace data that was captured. This skipped region could be
> padded with ignore packets at the end of the session, so that
> the decoder sees a continuous buffer with some padding at the
> beginning.
Just trying to understand,
Is there a possibility that lost data results in partial trace packets
towards the end of the buffer ? Or its always guaranteed that
trace packet end is always aligned with buffer end/limit ?
Thinking of a case when formatting is disabled.
The trace data written at the base is considered
> lost as the limit could have been in the middle of the perf
> ring buffer, and jumping to the "base" is not acceptable.
> We set the flags already to indicate that some amount of trace
> was lost during the FILL event IRQ. So this is fine.
>
> One important change with the work around is, we program the
> TRBBASER_EL1 to current page where we are allowed to write.
> Otherwise, it could overwrite a region that may be consumed
> by the perf. Towards this, we always make sure that the
> "handle->head" and thus the trbe_write is PAGE_SIZE aligned,
> so that we can set the BASE to the PAGE base and move the
> TRBPTR to the 256bytes offset.
>
> Cc: Mike Leach <mike.leach@linaro.org>
> Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
> Cc: Anshuman Khandual <anshuman.khandual@arm.com>
> Cc: Leo Yan <leo.yan@linaro.org>
> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
> ---
> drivers/hwtracing/coresight/coresight-trbe.c | 111 +++++++++++++++++--
> 1 file changed, 102 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/hwtracing/coresight/coresight-trbe.c b/drivers/hwtracing/coresight/coresight-trbe.c
> index 9ea28813182b..cd997ed5d918 100644
> --- a/drivers/hwtracing/coresight/coresight-trbe.c
> +++ b/drivers/hwtracing/coresight/coresight-trbe.c
> @@ -17,6 +17,7 @@
>
> #include <asm/barrier.h>
> #include <asm/cputype.h>
> +#include <asm/cpufeature.h>
>
> #include "coresight-self-hosted-trace.h"
> #include "coresight-trbe.h"
> @@ -84,9 +85,17 @@ struct trbe_buf {
> * per TRBE instance, we keep track of the list of errata that
> * affects the given instance of the TRBE.
> */
> -#define TRBE_ERRATA_MAX 0
> +#define TRBE_WORKAROUND_OVERWRITE_FILL_MODE 0
> +#define TRBE_ERRATA_MAX 1
> +
> +/*
> + * Safe limit for the number of bytes that may be overwritten
> + * when the erratum is triggered.
> + */
> +#define TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP 256
>
> static unsigned long trbe_errata_cpucaps[TRBE_ERRATA_MAX] = {
> + [TRBE_WORKAROUND_OVERWRITE_FILL_MODE] = ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE,
> };
>
> /*
> @@ -531,10 +540,13 @@ static enum trbe_fault_action trbe_get_fault_act(u64 trbsr)
> if ((ec == TRBE_EC_STAGE1_ABORT) || (ec == TRBE_EC_STAGE2_ABORT))
> return TRBE_FAULT_ACT_FATAL;
>
> - if (is_trbe_wrap(trbsr) && (ec == TRBE_EC_OTHERS) && (bsc == TRBE_BSC_FILLED)) {
> - if (get_trbe_write_pointer() == get_trbe_base_pointer())
> - return TRBE_FAULT_ACT_WRAP;
> - }
> + /*
> + * It is not necessary to verify the TRBPTR == TRBBASER to detect
> + * a FILL event. Moreover, CPU errata could make this check invalid.
> + */
> + if (is_trbe_wrap(trbsr) && (ec == TRBE_EC_OTHERS) && (bsc == TRBE_BSC_FILLED))
> + return TRBE_FAULT_ACT_WRAP;
> +
> return TRBE_FAULT_ACT_SPURIOUS;
> }
>
> @@ -544,6 +556,7 @@ static unsigned long trbe_get_trace_size(struct perf_output_handle *handle,
> {
> u64 write;
> u64 start_off, end_off;
> + u64 size;
>
> /*
> * If the TRBE has wrapped around the write pointer has
> @@ -559,7 +572,18 @@ static unsigned long trbe_get_trace_size(struct perf_output_handle *handle,
>
> if (WARN_ON_ONCE(end_off < start_off))
> return 0;
> - return (end_off - start_off);
> +
> + size = end_off - start_off;
> + /*
> + * If the TRBE is affected by the following erratum, we must fill
> + * the space we skipped with IGNORE packets. And we are always
> + * guaranteed to have at least a PAGE_SIZE space in the buffer.
> + */
> + if (trbe_has_erratum(TRBE_WORKAROUND_OVERWRITE_FILL_MODE, buf->cpudata) &&
> + !WARN_ON(size < TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP))
> + __trbe_pad_buf(buf, start_off, TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP);
> +
> + return size;
> }
>
> static void *arm_trbe_alloc_buffer(struct coresight_device *csdev,
> @@ -704,20 +728,73 @@ static unsigned long arm_trbe_update_buffer(struct coresight_device *csdev,
> return size;
> }
>
> +
> +static int trbe_apply_work_around_before_enable(struct trbe_buf *buf)
> +{
> + /*
> + * TRBE_WORKAROUND_OVERWRITE_FILL_MODE causes the TRBE to overwrite a few cache
> + * line size from the "TRBBASER_EL1" in the event of a "FILL".
> + * Thus, we could loose some amount of the trace at the base.
> + *
> + * To work around this:
> + * - Software must leave 256bytes of space from the base, so that
> + * the trace collected now is not overwritten.
> + * - Fill the first 256bytes with IGNORE packets for the decoder
> + * to ignore at the end of the session, so that the decoder ignores
> + * this gap.
> + *
> + * This also means that, the TRBE driver must set the TRBBASER_EL1
> + * such that, when the erratum is triggered, it doesn't overwrite
> + * the "area" outside the area marked by (handle->head, +size).
> + * So, we make sure that the handle->head is always PAGE aligned,
> + * by tweaking the required alignment for the TRBE (trbe_align).
> + * And when we enable the TRBE,
> + *
> + * - move the TRBPTR_EL1 to 256bytes past the starting point.
> + * So that any trace collected in this run is not overwritten.
> + *
> + * - set the TRBBASER_EL1 to the original trbe_write. This will
> + * ensure that, if the TRBE hits the erratum, it would only
> + * write within the region allowed for the TRBE.
> + *
> + * At the trace collection time, we always pad the skipped bytes
> + * with IGNORE packets to make sure the decoder doesn't see any
> + * overwritten packets.
> + */
> + if (trbe_has_erratum(TRBE_WORKAROUND_OVERWRITE_FILL_MODE, buf->cpudata)) {
> + if (WARN_ON(!IS_ALIGNED(buf->trbe_write, PAGE_SIZE)))
> + return -EINVAL;
> + buf->trbe_hw_base = buf->trbe_write;
> + buf->trbe_write += TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP;
> + }
> +
> + return 0;
> +}
> +
> static int __arm_trbe_enable(struct trbe_buf *buf,
> struct perf_output_handle *handle)
> {
> + int ret = 0;
> +
> buf->trbe_limit = compute_trbe_buffer_limit(handle);
> buf->trbe_write = buf->trbe_base + PERF_IDX2OFF(handle->head, buf);
> if (buf->trbe_limit == buf->trbe_base) {
> - trbe_stop_and_truncate_event(handle);
> - return -ENOSPC;
> + ret = -ENOSPC;
> + goto err;
> }
> /* Set the base of the TRBE to the buffer base */
> buf->trbe_hw_base = buf->trbe_base;
> +
> + ret = trbe_apply_work_around_before_enable(buf);
> + if (ret)
> + goto err;
> +
> *this_cpu_ptr(buf->cpudata->drvdata->handle) = handle;
> trbe_enable_hw(buf);
> return 0;
> +err:
> + trbe_stop_and_truncate_event(handle);
> + return ret;
> }
>
> static int arm_trbe_enable(struct coresight_device *csdev, u32 mode, void *data)
> @@ -1003,7 +1080,23 @@ static void arm_trbe_probe_cpu(void *info)
> pr_err("Unsupported alignment on cpu %d\n", cpu);
> goto cpu_clear;
> }
> - cpudata->trbe_align = cpudata->trbe_hw_align;
> +
> + /*
> + * If the TRBE is affected by erratum TRBE_WORKAROUND_OVERWRITE_FILL_MODE,
> + * we must always program the TBRPTR_EL1, 256bytes from a page
> + * boundary, with TRBBASER_EL1 set to the page, to prevent
> + * TRBE over-writing 256bytes at TRBBASER_EL1 on FILL event.
> + *
> + * Thus make sure we always align our write pointer to a PAGE_SIZE,
> + * which also guarantees that we have at least a PAGE_SIZE space in
> + * the buffer (TRBLIMITR is PAGE aligned) and thus we can skip
> + * the required bytes at the base.
> + */
> + if (trbe_has_erratum(TRBE_WORKAROUND_OVERWRITE_FILL_MODE, cpudata))
> + cpudata->trbe_align = PAGE_SIZE;
> + else
> + cpudata->trbe_align = cpudata->trbe_hw_align;
> +
> cpudata->trbe_flag = get_trbe_flag_update(trbidr);
> cpudata->cpu = cpu;
> cpudata->drvdata = drvdata;
> --
> 2.24.1
>
> _______________________________________________
> CoreSight mailing list
> CoreSight@lists.linaro.org
> https://lists.linaro.org/mailman/listinfo/coresight
next prev parent reply other threads:[~2021-08-06 16:10 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-28 13:52 [PATCH 00/10] arm64: Self-hosted trace related erratum workarouds Suzuki K Poulose
2021-07-28 13:52 ` [PATCH 01/10] coresight: trbe: Add infrastructure for Errata handling Suzuki K Poulose
2021-08-02 6:43 ` Anshuman Khandual
2021-09-07 9:04 ` Suzuki K Poulose
2021-09-09 2:55 ` Anshuman Khandual
2021-07-28 13:52 ` [PATCH 02/10] coresight: trbe: Add a helper to calculate the trace generated Suzuki K Poulose
2021-07-30 10:01 ` Anshuman Khandual
2021-07-28 13:52 ` [PATCH 03/10] coresight: trbe: Add a helper to pad a given buffer area Suzuki K Poulose
2021-07-30 10:05 ` Anshuman Khandual
2021-07-28 13:52 ` [PATCH 04/10] coresight: trbe: Decouple buffer base from the hardware base Suzuki K Poulose
2021-07-30 10:53 ` Anshuman Khandual
2021-07-28 13:52 ` [PATCH 05/10] coresight: trbe: Allow driver to choose a different alignment Suzuki K Poulose
2021-07-30 11:02 ` Anshuman Khandual
2021-07-30 14:29 ` Suzuki K Poulose
2021-07-28 13:52 ` [PATCH 06/10] arm64: Add Neoverse-N2, Cortex-A710 CPU part definition Suzuki K Poulose
2021-07-30 11:26 ` Anshuman Khandual
2021-07-30 14:31 ` Suzuki K Poulose
2021-08-02 11:21 ` Catalin Marinas
2021-08-02 11:21 ` Catalin Marinas
2021-07-28 13:52 ` [PATCH 07/10] arm64: Add erratum detection for TRBE overwrite in FILL mode Suzuki K Poulose
2021-08-02 7:44 ` Anshuman Khandual
2021-08-02 11:22 ` Catalin Marinas
2021-08-06 12:44 ` Linu Cherian
2021-09-07 9:10 ` Suzuki K Poulose
2021-07-28 13:52 ` [PATCH 08/10] coresight: trbe: Workaround TRBE errat " Suzuki K Poulose
2021-08-03 10:25 ` Anshuman Khandual
2021-09-07 9:58 ` Suzuki K Poulose
2021-09-09 4:21 ` Anshuman Khandual
2021-09-09 8:37 ` Suzuki K Poulose
2021-08-06 16:09 ` Linu Cherian [this message]
2021-09-07 9:18 ` Suzuki K Poulose
2021-07-28 13:52 ` [PATCH 09/10] arm64: Enable workaround for TRBE " Suzuki K Poulose
2021-08-02 9:34 ` Anshuman Khandual
2021-08-02 11:24 ` Catalin Marinas
2021-07-28 13:52 ` [PATCH 10/10] arm64: errata: Add workaround for TSB flush failures Suzuki K Poulose
2021-07-29 9:55 ` Marc Zyngier
2021-07-29 10:41 ` Suzuki K Poulose
2021-08-02 9:12 ` Anshuman Khandual
2021-08-02 9:35 ` Marc Zyngier
2021-08-03 3:51 ` Anshuman Khandual
2021-09-08 13:39 ` Suzuki K Poulose
2021-08-02 11:27 ` Catalin Marinas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAAHhmWjR6XYo5j_h3jfLsmWzqD9i9L-pHq=zrrdrw9YTXmuCqg@mail.gmail.com' \
--to=linuc.decode@gmail.com \
--cc=anshuman.khandual@arm.com \
--cc=catalin.marinas@arm.com \
--cc=coresight@lists.linaro.org \
--cc=james.morse@arm.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=maz@kernel.org \
--cc=mike.leach@linaro.org \
--cc=suzuki.poulose@arm.com \
--cc=will@kernel.org \
--subject='Re: [PATCH 08/10] coresight: trbe: Workaround TRBE errat overwrite in FILL mode' \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).