LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* [PATCH v2] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema
@ 2019-05-10 15:45 Alexandre Torgue
  2019-05-14 20:14 ` Rob Herring
  2019-05-24 11:41 ` Linus Walleij
  0 siblings, 2 replies; 3+ messages in thread
From: Alexandre Torgue @ 2019-05-10 15:45 UTC (permalink / raw)
  To: Maxime Coquelin, Linus Walleij, Rob Herring, Mark Rutland
  Cc: linux-arm-kernel, devicetree, linux-kernel, linux-gpio,
	linux-stm32, Alexandre Torgue

Convert the STM32 pinctrl binding to DT schema format using json-schema.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
---

Hi,

First pacth to convert DT bindings file (here pinctrl STM32) to json-schema
in order to take advantage of devicetree validation tool for STM32.

Changes since v1:
 - Fix errors reported by Rob.


regards
Alex

diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
deleted file mode 100644
index 0016925..0000000
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ /dev/null
@@ -1,208 +0,0 @@
-* STM32 GPIO and Pin Mux/Config controller
-
-STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
-controller. It controls the input/output settings on the available pins and
-also provides ability to multiplex and configure the output of various on-chip
-controllers onto these pads.
-
-Pin controller node:
-Required properies:
- - compatible: value should be one of the following:
-   "st,stm32f429-pinctrl"
-   "st,stm32f469-pinctrl"
-   "st,stm32f746-pinctrl"
-   "st,stm32f769-pinctrl"
-   "st,stm32h743-pinctrl"
-   "st,stm32mp157-pinctrl"
-   "st,stm32mp157-z-pinctrl"
- - #address-cells: The value of this property must be 1
- - #size-cells	: The value of this property must be 1
- - ranges	: defines mapping between pin controller node (parent) to
-   gpio-bank node (children).
- - pins-are-numbered: Specify the subnodes are using numbered pinmux to
-   specify pins.
-
-GPIO controller/bank node:
-Required properties:
- - gpio-controller : Indicates this device is a GPIO controller
- - #gpio-cells	  : Should be two.
-			The first cell is the pin number
-			The second one is the polarity:
-				- 0 for active high
-				- 1 for active low
- - reg		  : The gpio address range, relative to the pinctrl range
- - clocks	  : clock that drives this bank
- - st,bank-name	  : Should be a name string for this bank as specified in
-   the datasheet
-
-Optional properties:
- - reset:	  : Reference to the reset controller
- - st,syscfg: Should be phandle/offset/mask.
-	-The phandle to the syscon node which includes IRQ mux selection register.
-	-The offset of the IRQ mux selection register
-	-The field mask of IRQ mux, needed if different of 0xf.
- - gpio-ranges: Define a dedicated mapping between a pin-controller and
-   a gpio controller. Format is <&phandle a b c> with:
-	-(phandle): phandle of pin-controller.
-	-(a): gpio base offset in range.
-	-(b): pin base offset in range.
-	-(c): gpio count in range
-   This entry has to be used either if there are holes inside a bank:
-	GPIOB0/B1/B2/B14/B15 (see example 2)
-   or if banks are not contiguous:
-	GPIOA/B/C/E...
-   NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller
-   have to use a "gpio-ranges" entry.
-   More details in Documentation/devicetree/bindings/gpio/gpio.txt.
- - st,bank-ioport: should correspond to the EXTI IOport selection (EXTI line
-   used to select GPIOs as interrupts).
- - hwlocks: reference to a phandle of a hardware spinlock provider node.
- - st,package: Indicates the SOC package used.
-   More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
-
-Example 1:
-#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
-...
-
-	pin-controller {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,stm32f429-pinctrl";
-		ranges = <0 0x40020000 0x3000>;
-		pins-are-numbered;
-
-		gpioa: gpio@40020000 {
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <0x0 0x400>;
-			resets = <&reset_ahb1 0>;
-			st,bank-name = "GPIOA";
-		};
-		...
-		pin-functions nodes follow...
-	};
-
-Example 2:
-#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
-...
-
-	pinctrl: pin-controller {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,stm32f429-pinctrl";
-		ranges = <0 0x40020000 0x3000>;
-		pins-are-numbered;
-
-		gpioa: gpio@40020000 {
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <0x0 0x400>;
-			resets = <&reset_ahb1 0>;
-			st,bank-name = "GPIOA";
-			gpio-ranges = <&pinctrl 0 0 16>;
-		};
-
-		gpiob: gpio@40020400 {
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <0x0 0x400>;
-			resets = <&reset_ahb1 0>;
-			st,bank-name = "GPIOB";
-			ngpios = 4;
-			gpio-ranges = <&pinctrl 0 16 3>,
-				      <&pinctrl 14 30 2>;
-		};
-
-
-		...
-		pin-functions nodes follow...
-	};
-
-
-Contents of function subnode node:
-----------------------------------
-Subnode format
-A pinctrl node should contain at least one subnode representing the
-pinctrl group available on the machine. Each subnode will list the
-pins it needs, and how they should be configured, with regard to muxer
-configuration, pullups, drive, output high/low and output speed.
-
-    node {
-	pinmux = <PIN_NUMBER_PINMUX>;
-	GENERIC_PINCONFIG;
-    };
-
-Required properties:
-- pinmux: integer array, represents gpio pin number and mux setting.
-  Supported pin number and mux varies for different SoCs, and are defined in
-  dt-bindings/pinctrl/<soc>-pinfunc.h directly.
-  These defines are calculated as:
-    ((port * 16 + line) << 8) | function
-  With:
-    - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
-    - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
-    - function: The function number, can be:
-      * 0 : GPIO
-      * 1 : Alternate Function 0
-      * 2 : Alternate Function 1
-      * 3 : Alternate Function 2
-      * ...
-      * 16 : Alternate Function 15
-      * 17 : Analog
-
-  To simplify the usage, macro is available to generate "pinmux" field.
-  This macro is available here:
-    - include/dt-bindings/pinctrl/stm32-pinfunc.h
-
-  Some examples of using macro:
-    /* GPIO A9 set as alernate function 2 */
-    ... {
-		pinmux = <STM32_PINMUX('A', 9, AF2)>;
-    };
-    /* GPIO A9 set as GPIO  */
-    ... {
-		pinmux = <STM32_PINMUX('A', 9, GPIO)>;
-    };
-    /* GPIO A9 set as analog */
-    ... {
-		pinmux = <STM32_PINMUX('A', 9, ANALOG)>;
-    };
-
-Optional properties:
-- GENERIC_PINCONFIG: is the generic pinconfig options to use.
-  Available options are:
-   - bias-disable,
-   - bias-pull-down,
-   - bias-pull-up,
-   - drive-push-pull,
-   - drive-open-drain,
-   - output-low
-   - output-high
-   - slew-rate = <x>, with x being:
-       < 0 > : Low speed
-       < 1 > : Medium speed
-       < 2 > : Fast speed
-       < 3 > : High speed
-
-Example:
-
-pin-controller {
-...
-	usart1_pins_a: usart1@0 {
-		pins1 {
-			pinmux = <STM32_PINMUX('A', 9, AF7)>;
-			bias-disable;
-			drive-push-pull;
-			slew-rate = <0>;
-		};
-		pins2 {
-			pinmux = <STM32_PINMUX('A', 10, AF7)>;
-			bias-disable;
-		};
-	};
-};
-
-&usart1 {
-	pinctrl-0 = <&usart1_pins_a>;
-	pinctrl-names = "default";
-};
diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml
new file mode 100644
index 0000000..06c4b66
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml
@@ -0,0 +1,264 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (C) STMicroelectronics 2019.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/st,stm32-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STM32 GPIO and Pin Mux/Config controller
+
+maintainers:
+  - Alexandre TORGUE <alexandre.torgue@st.com>
+
+description: |
+  STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
+  controller. It controls the input/output settings on the available pins and
+  also provides ability to multiplex and configure the output of various
+  on-chip controllers onto these pads.
+
+properties:
+  compatible:
+    enum:
+      - st,stm32f429-pinctrl
+      - st,stm32f469-pinctrl
+      - st,stm32f746-pinctrl
+      - st,stm32f769-pinctrl
+      - st,stm32h743-pinctrl
+      - st,stm32mp157-pinctrl
+      - st,stm32mp157-z-pinctrl
+
+  '#address-cells':
+    const: 1
+  '#size-cells':
+    const: 1
+
+  ranges: true
+  pins-are-numbered: true
+  hwlocks: true
+
+  st,syscfg:
+    $ref: "/schemas/types.yaml#/definitions/phandle-array"
+    description: Should be phandle/offset/mask
+    items:
+      - description: Phandle to the syscon node which includes IRQ mux selection.
+      - description: The offset of the IRQ mux selection register.
+      - description: The field mask of IRQ mux, needed if different of 0xf.
+
+  st,package:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 2, 4, 8]
+    description:
+     Indicates the SOC package used.
+     More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
+
+
+patternProperties:
+  '^gpio@[0-9a-f]*$':
+    properties:
+      gpio-controller: true
+      '#gpio-cells':
+        const: 2
+
+      reg:
+        maxItems: 1
+      clocks:
+        maxItems: 1
+      reset:
+        minItems: 1
+        maxItems: 1
+      gpio-ranges:
+        minItems: 1
+        maxItems: 16
+      ngpios:
+        description:
+          Number of available gpios in a bank.
+        minimum: 1
+        maximum: 16
+
+      st,bank-name:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum:
+            - GPIOA
+            - GPIOB
+            - GPIOC
+            - GPIOD
+            - GPIOE
+            - GPIOF
+            - GPIOG
+            - GPIOH
+            - GPIOI
+            - GPIOJ
+            - GPIOK
+            - GPIOZ
+        description:
+          Should be a name string for this bank as specified in the datasheet.
+
+      st,bank-ioport:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+          - maximum: 11
+
+        description:
+          Should correspond to the EXTI IOport selection (EXTI line used
+          to select GPIOs as interrupts).
+
+    required:
+      - gpio-controller
+      - '#gpio-cells'
+      - reg
+      - clocks
+      - st,bank-name
+
+  '-[0-9]*$':
+    patternProperties:
+      '^pins':
+        description: |
+          A pinctrl node should contain at least one subnode representing the
+          pinctrl group available on the machine. Each subnode will list the
+          pins it needs, and how they should be configured, with regard to muxer
+          configuration, pullups, drive, output high/low and output speed.
+        properties:
+          pinmux:
+            allOf:
+              - $ref: "/schemas/types.yaml#/definitions/uint32-array"
+            description: |
+              Integer array, represents gpio pin number and mux setting.
+              Supported pin number and mux varies for different SoCs, and are
+              defined in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
+              These defines are calculated as: ((port * 16 + line) << 8) | function
+              With:
+              - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
+              - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
+              - function: The function number, can be:
+              * 0 : GPIO
+              * 1 : Alternate Function 0
+              * 2 : Alternate Function 1
+              * 3 : Alternate Function 2
+              * ...
+              * 16 : Alternate Function 15
+              * 17 : Analog
+              To simplify the usage, macro is available to generate "pinmux" field.
+              This macro is available here:
+                - include/dt-bindings/pinctrl/stm32-pinfunc.h
+              Some examples of using macro:
+               /* GPIO A9 set as alernate function 2 */
+               ... {
+                          pinmux = <STM32_PINMUX('A', 9, AF2)>;
+               };
+               /* GPIO A9 set as GPIO  */
+               ... {
+                          pinmux = <STM32_PINMUX('A', 9, GPIO)>;
+               };
+               /* GPIO A9 set as analog */
+               ... {
+                          pinmux = <STM32_PINMUX('A', 9, ANALOG)>;
+               };
+
+          bias-disable:
+            type: boolean
+          bias-pull-down:
+            type: boolean
+          bias-pull-up:
+            type: boolean
+          drive-push-pull:
+            type: boolean
+          drive-open-drain:
+            type: boolean
+          output-low:
+            type: boolean
+          output-high:
+            type: boolean
+          slew-rate:
+            description: |
+              0: Low speed
+              1: Medium speed
+              2: Fast speed
+              3: High speed
+            allOf:
+              - $ref: /schemas/types.yaml#/definitions/uint32
+              - enum: [0, 1, 2, 3]
+
+        required:
+          - pinmux
+
+required:
+  - compatible
+  - '#address-cells'
+  - '#size-cells'
+  - ranges
+  - pins-are-numbered
+
+examples:
+  - |
+    #include <dt-bindings/pinctrl/stm32-pinfunc.h>
+    //Example 1
+      pinctrl@40020000 {
+              #address-cells = <1>;
+              #size-cells = <1>;
+              compatible = "st,stm32f429-pinctrl";
+              ranges = <0 0x40020000 0x3000>;
+              pins-are-numbered;
+
+              gpioa: gpio@0 {
+                      gpio-controller;
+                      #gpio-cells = <2>;
+                      reg = <0x0 0x400>;
+                      resets = <&reset_ahb1 0>;
+                      st,bank-name = "GPIOA";
+              };
+       };
+
+    //Example 2 (using gpio-ranges)
+      pinctrl@50020000 {
+              #address-cells = <1>;
+              #size-cells = <1>;
+              compatible = "st,stm32f429-pinctrl";
+              ranges = <0 0x50020000 0x3000>;
+              pins-are-numbered;
+
+              gpiob: gpio@1000 {
+                      gpio-controller;
+                      #gpio-cells = <2>;
+                      reg = <0x1000 0x400>;
+                      resets = <&reset_ahb1 0>;
+                      st,bank-name = "GPIOB";
+                      gpio-ranges = <&pinctrl 0 0 16>;
+              };
+
+              gpioc: gpio@2000 {
+                      gpio-controller;
+                      #gpio-cells = <2>;
+                      reg = <0x2000 0x400>;
+                      resets = <&reset_ahb1 0>;
+                      st,bank-name = "GPIOC";
+                      ngpios = <5>;
+                      gpio-ranges = <&pinctrl 0 16 3>,
+                                    <&pinctrl 14 30 2>;
+              };
+      };
+
+    //Example 3 pin groups
+      pinctrl@60020000 {
+        usart1_pins_a: usart1-0 {
+                pins1 {
+                        pinmux = <STM32_PINMUX('A', 9, AF7)>;
+                        bias-disable;
+                        drive-push-pull;
+                        slew-rate = <0>;
+                };
+                pins2 {
+                        pinmux = <STM32_PINMUX('A', 10, AF7)>;
+                        bias-disable;
+                };
+        };
+    };
+
+    usart1 {
+                pinctrl-0 = <&usart1_pins_a>;
+                pinctrl-names = "default";
+    };
+
+...
-- 
2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH v2] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema
  2019-05-10 15:45 [PATCH v2] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema Alexandre Torgue
@ 2019-05-14 20:14 ` Rob Herring
  2019-05-24 11:41 ` Linus Walleij
  1 sibling, 0 replies; 3+ messages in thread
From: Rob Herring @ 2019-05-14 20:14 UTC (permalink / raw)
  To: Alexandre Torgue
  Cc: Maxime Coquelin, Linus Walleij, Mark Rutland, linux-arm-kernel,
	devicetree, linux-kernel, linux-gpio, linux-stm32,
	Alexandre Torgue

On Fri, 10 May 2019 17:45:26 +0200, Alexandre Torgue wrote:
> Convert the STM32 pinctrl binding to DT schema format using json-schema.
> 
> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
> ---
> 
> Hi,
> 
> First pacth to convert DT bindings file (here pinctrl STM32) to json-schema
> in order to take advantage of devicetree validation tool for STM32.
> 
> Changes since v1:
>  - Fix errors reported by Rob.
> 
> 
> regards
> Alex
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH v2] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema
  2019-05-10 15:45 [PATCH v2] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema Alexandre Torgue
  2019-05-14 20:14 ` Rob Herring
@ 2019-05-24 11:41 ` Linus Walleij
  1 sibling, 0 replies; 3+ messages in thread
From: Linus Walleij @ 2019-05-24 11:41 UTC (permalink / raw)
  To: Alexandre Torgue
  Cc: Maxime Coquelin, Rob Herring, Mark Rutland, Linux ARM,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	linux-kernel, open list:GPIO SUBSYSTEM, linux-stm32

On Fri, May 10, 2019 at 5:45 PM Alexandre Torgue
<alexandre.torgue@st.com> wrote:

> Convert the STM32 pinctrl binding to DT schema format using json-schema.
>
> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

What a feat. Well done!
Patch applied with Rob's Review tag.

Yours,
Linus Walleij

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2019-05-24 11:41 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-10 15:45 [PATCH v2] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema Alexandre Torgue
2019-05-14 20:14 ` Rob Herring
2019-05-24 11:41 ` Linus Walleij

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).