LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Anand Moon <linux.amoon@gmail.com>
To: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Linux USB Mailing List <linux-usb@vger.kernel.org>,
	devicetree <devicetree@vger.kernel.org>,
	linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
	linux-samsung-soc@vger.kernel.org,
	Linux Kernel <linux-kernel@vger.kernel.org>,
	"open list:COMMON CLK FRAMEWORK" <linux-clk@vger.kernel.org>,
	Rob Herring <robh+dt@kernel.org>, Kukjin Kim <kgene@kernel.org>,
	Marek Szyprowski <m.szyprowski@samsung.com>,
	Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>,
	Felipe Balbi <balbi@kernel.org>,
	Sylwester Nawrocki <s.nawrocki@samsung.com>,
	Tomasz Figa <tomasz.figa@gmail.com>,
	Chanwoo Choi <cw00.choi@samsung.com>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>
Subject: Re: [PATCHv3 5/5] clk: samsung: exynos542x: Move FSYS subsystem clocks to its sub-CMU
Date: Thu, 12 Mar 2020 16:04:57 +0530	[thread overview]
Message-ID: <CANAwSgQWYdh3awuMCjUvz6EvnwMq9rDOSBn5EkNcA7OfsjoEwA@mail.gmail.com> (raw)
In-Reply-To: <20200311144248.GA4455@kozik-lap>

Hi Krzysztof,

Thanks for your review comments.

On Wed, 11 Mar 2020 at 20:12, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>
> On Tue, Mar 10, 2020 at 07:48:54PM +0000, Anand Moon wrote:
> > FSYS power domain support usbdrd3, pdma and usb2 power gaiting,
> > hence move FSYS clk setting to sub-CMU block to support power domain
> > on/off sequences for device nodes.
> >
> > Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> > ---
> > New patch in the series
> > ---
> >  drivers/clk/samsung/clk-exynos5420.c | 45 +++++++++++++++++++++-------
> >  1 file changed, 34 insertions(+), 11 deletions(-)
> >
> > diff --git a/drivers/clk/samsung/clk-exynos5420.c b/drivers/clk/samsung/clk-exynos5420.c
> > index c9e5a1fb6653..6c4c47dfcdce 100644
> > --- a/drivers/clk/samsung/clk-exynos5420.c
> > +++ b/drivers/clk/samsung/clk-exynos5420.c
> > @@ -859,12 +859,6 @@ static const struct samsung_div_clock exynos5x_div_clks[] __initconst = {
> >       DIV(0, "dout_maudio0", "mout_maudio0", DIV_MAU, 20, 4),
> >       DIV(0, "dout_maupcm0", "dout_maudio0", DIV_MAU, 24, 8),
> >
> > -     /* USB3.0 */
> > -     DIV(0, "dout_usbphy301", "mout_usbd301", DIV_FSYS0, 12, 4),
> > -     DIV(0, "dout_usbphy300", "mout_usbd300", DIV_FSYS0, 16, 4),
> > -     DIV(0, "dout_usbd301", "mout_usbd301", DIV_FSYS0, 20, 4),
> > -     DIV(0, "dout_usbd300", "mout_usbd300", DIV_FSYS0, 24, 4),
>
> According to clock diagram these are still in CMU TOP, not FSYS.
>
> > -
> >       /* MMC */
> >       DIV(0, "dout_mmc0", "mout_mmc0", DIV_FSYS1, 0, 10),
> >       DIV(0, "dout_mmc1", "mout_mmc1", DIV_FSYS1, 10, 10),
> > @@ -1031,8 +1025,6 @@ static const struct samsung_gate_clock exynos5x_gate_clks[] __initconst = {
> />
> >       /* FSYS Block */
> >       GATE(CLK_TSI, "tsi", "aclk200_fsys", GATE_BUS_FSYS0, 0, 0, 0),
> > -     GATE(CLK_PDMA0, "pdma0", "aclk200_fsys", GATE_BUS_FSYS0, 1, 0, 0),
> > -     GATE(CLK_PDMA1, "pdma1", "aclk200_fsys", GATE_BUS_FSYS0, 2, 0, 0),
> >       GATE(CLK_UFS, "ufs", "aclk200_fsys2", GATE_BUS_FSYS0, 3, 0, 0),
> >       GATE(CLK_RTIC, "rtic", "aclk200_fsys", GATE_IP_FSYS, 9, 0, 0),
> >       GATE(CLK_MMC0, "mmc0", "aclk200_fsys2", GATE_IP_FSYS, 12, 0, 0),
> > @@ -1040,9 +1032,6 @@ static const struct samsung_gate_clock exynos5x_gate_clks[] __initconst = {
> >       GATE(CLK_MMC2, "mmc2", "aclk200_fsys2", GATE_IP_FSYS, 14, 0, 0),
> >       GATE(CLK_SROMC, "sromc", "aclk200_fsys2",
> >                       GATE_IP_FSYS, 17, CLK_IGNORE_UNUSED, 0),
> > -     GATE(CLK_USBH20, "usbh20", "aclk200_fsys", GATE_IP_FSYS, 18, 0, 0),
> > -     GATE(CLK_USBD300, "usbd300", "aclk200_fsys", GATE_IP_FSYS, 19, 0, 0),
> > -     GATE(CLK_USBD301, "usbd301", "aclk200_fsys", GATE_IP_FSYS, 20, 0, 0),
> >       GATE(CLK_SCLK_UNIPRO, "sclk_unipro", "dout_unipro",
> >                       SRC_MASK_FSYS, 24, CLK_SET_RATE_PARENT, 0),
> >
> > @@ -1258,6 +1247,28 @@ static struct exynos5_subcmu_reg_dump exynos5x_gsc_suspend_regs[] = {
> >       { DIV2_RATIO0, 0, 0x30 },       /* DIV dout_gscl_blk_300 */
> >  };
> >
> > +/* USB3.0 */
> > +static const struct samsung_div_clock exynos5x_fsys_div_clks[] __initconst = {
> > +     DIV(0, "dout_usbphy301", "mout_usbd301", DIV_FSYS0, 12, 4),
> > +     DIV(0, "dout_usbphy300", "mout_usbd300", DIV_FSYS0, 16, 4),
> > +     DIV(0, "dout_usbd301", "mout_usbd301", DIV_FSYS0, 20, 4),
> > +     DIV(0, "dout_usbd300", "mout_usbd300", DIV_FSYS0, 24, 4),
> > +};
> > +
> > +static const struct samsung_gate_clock exynos5x_fsys_gate_clks[] __initconst = {
> > +     GATE(CLK_PDMA0, "pdma0", "aclk200_fsys", GATE_BUS_FSYS0, 1, 0, 0),
> > +     GATE(CLK_PDMA1, "pdma1", "aclk200_fsys", GATE_BUS_FSYS0, 2, 0, 0),
> > +     GATE(CLK_USBH20, "usbh20", "aclk200_fsys", GATE_IP_FSYS, 18, 0, 0),
> > +     GATE(CLK_USBD300, "usbd300", "aclk200_fsys", GATE_IP_FSYS, 19, 0, 0),
> > +     GATE(CLK_USBD301, "usbd301", "aclk200_fsys", GATE_IP_FSYS, 20, 0, 0),
> > +};
> > +
> > +static struct exynos5_subcmu_reg_dump exynos5x_fsys_suspend_regs[] = {
> > +     { GATE_IP_FSYS, 0xffffffff, 0xffffffff }, /* FSYS gates */
>
> This looks wrong. GATE_IP_FSYS has fields also for FSYS2 clocks which
> you are not suspending. They do not belong to this CMU.
>

Ok. I change the from GATE_IP_FSYS to GATE_BUS_FSYS0 in the above
exynos5x_fsys_gate_clks to make this consistent to used GATE_BUS_FSYS0 for CMU,
with this change it works as per previously.

> Don't you need to save also parts of GATE_BUS_FSYS0?

GATE_BUS_FSYS0 and GATE_IP_FSYS are already part of list
of control register which are saved and restored during suspend and resume
so no point in adding this here, I should drop the GATE_IP_FSYS reg
dump over here.

>
> > +     { SRC_TOP3, 0, BIT(24) },                 /* SW_MUX_PCLK_200_FSYS_SEL */
> > +     { SRC_TOP3, 0, BIT(28) },                 /* SW_MUX_ACLK_200_FSYS_SEL */
>
> Name of clocks from the driver please, not from datasheet. Look at other
> examples.
>

Ok  I will update this as per the examples.

> Best regards,
> Krzysztof
>
>

-Anand

> > +};
> > +
> >  static const struct samsung_gate_clock exynos5x_g3d_gate_clks[] __initconst = {
> >       GATE(CLK_G3D, "g3d", "mout_user_aclk_g3d", GATE_IP_G3D, 9,
> >            CLK_SET_RATE_PARENT, 0),
> > @@ -1376,12 +1387,23 @@ static const struct exynos5_subcmu_info exynos5800_mau_subcmu = {
> >       .pd_name        = "MAU",
> >  };
> >
> > +static const struct exynos5_subcmu_info exynos5x_fsys_subcmu = {
> > +     .div_clks       = exynos5x_fsys_div_clks,
> > +     .nr_div_clks    = ARRAY_SIZE(exynos5x_fsys_div_clks),
> > +     .gate_clks      = exynos5x_fsys_gate_clks,
> > +     .nr_gate_clks   = ARRAY_SIZE(exynos5x_fsys_gate_clks),
> > +     .suspend_regs   = exynos5x_fsys_suspend_regs,
> > +     .nr_suspend_regs = ARRAY_SIZE(exynos5x_fsys_suspend_regs),
> > +     .pd_name        = "FSYS",
> > +};
> > +
> >  static const struct exynos5_subcmu_info *exynos5x_subcmus[] = {
> >       &exynos5x_disp_subcmu,
> >       &exynos5x_gsc_subcmu,
> >       &exynos5x_g3d_subcmu,
> >       &exynos5x_mfc_subcmu,
> >       &exynos5x_mscl_subcmu,
> > +     &exynos5x_fsys_subcmu,
> >  };
> >
> >  static const struct exynos5_subcmu_info *exynos5800_subcmus[] = {
> > @@ -1391,6 +1413,7 @@ static const struct exynos5_subcmu_info *exynos5800_subcmus[] = {
> >       &exynos5x_mfc_subcmu,
> >       &exynos5x_mscl_subcmu,
> >       &exynos5800_mau_subcmu,
> > +     &exynos5x_fsys_subcmu,
> >  };
> >
> >  static const struct samsung_pll_rate_table exynos5420_pll2550x_24mhz_tbl[] __initconst = {
> > --
> > 2.25.1
> >

  reply	other threads:[~2020-03-12 10:35 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-03-10 19:48 [PATCHv3 0/5] Add support for FSYS power domain and enable suspend clk for Exynos542x SoC Anand Moon
2020-03-10 19:48 ` [PATCHv3 1/5] devicetree: bindings: exynos: Add new compatible for Exynos5420 dwc3 clocks support Anand Moon
2020-03-15  9:07   ` Felipe Balbi
2020-03-15  9:25     ` Anand Moon
2020-03-17  8:42     ` Krzysztof Kozlowski
2020-03-10 19:48 ` [PATCHv3 2/5] ARM: dts: exynos: Add missing usbdrd3 suspend clk Anand Moon
2020-03-14 13:32   ` Anand Moon
2020-03-14 18:20     ` Krzysztof Kozlowski
2020-03-15  9:46       ` Anand Moon
2020-03-10 19:48 ` [PATCHv3 3/5] ARM: dts: exynos: Add FSYS power domain to Exynos542x USB nodes Anand Moon
2020-03-10 19:48 ` [PATCHv3 4/5] usb: dwc3: exynos: Add support for Exynos5422 suspend clk Anand Moon
2020-03-10 19:48 ` [PATCHv3 5/5] clk: samsung: exynos542x: Move FSYS subsystem clocks to its sub-CMU Anand Moon
2020-03-11 14:42   ` Krzysztof Kozlowski
2020-03-12 10:34     ` Anand Moon [this message]
2020-03-12 11:36       ` Krzysztof Kozlowski
2020-03-12 12:54         ` Anand Moon
2020-03-12 14:08           ` Anand Moon
2020-03-14 17:41             ` Krzysztof Kozlowski

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CANAwSgQWYdh3awuMCjUvz6EvnwMq9rDOSBn5EkNcA7OfsjoEwA@mail.gmail.com \
    --to=linux.amoon@gmail.com \
    --cc=b.zolnierkie@samsung.com \
    --cc=balbi@kernel.org \
    --cc=cw00.choi@samsung.com \
    --cc=devicetree@vger.kernel.org \
    --cc=kgene@kernel.org \
    --cc=krzk@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-samsung-soc@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=m.szyprowski@samsung.com \
    --cc=mturquette@baylibre.com \
    --cc=robh+dt@kernel.org \
    --cc=s.nawrocki@samsung.com \
    --cc=sboyd@kernel.org \
    --cc=tomasz.figa@gmail.com \
    --subject='Re: [PATCHv3 5/5] clk: samsung: exynos542x: Move FSYS subsystem clocks to its sub-CMU' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).