LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
* [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01
@ 2021-08-28 11:26 Paul Cercueil
  2021-08-28 11:26 ` [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD Paul Cercueil
                   ` (2 more replies)
  0 siblings, 3 replies; 6+ messages in thread
From: Paul Cercueil @ 2021-08-28 11:26 UTC (permalink / raw)
  To: Thierry Reding, Sam Ravnborg, Rob Herring
  Cc: Christophe Branchereau, list, dri-devel, devicetree,
	linux-kernel, Paul Cercueil

Add binding for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
24-bit TFT LCD panel with non-square pixels and a delta-RGB 8-bit
interface.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 .../bindings/display/panel/auo,a030jtn01.yaml | 57 +++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml b/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml
new file mode 100644
index 000000000000..21c9d62e3625
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/auo,a030jtn01.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: AUO A030JTN01 3.0" (320x480 pixels) 24-bit TFT LCD
+
+description: |
+  The panel must obey the rules for a SPI slave device as specified in
+  spi/spi-controller.yaml
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: auo,a030jtn01
+
+  backlight: true
+  port: true
+  power-supply: true
+  reg: true
+  reset-gpios: true
+
+required:
+  - compatible
+  - reg
+  - power-supply
+  - reset-gpios
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    panel@0 {
+      compatible = "auo,a030jtn01";
+      reg = <0>;
+
+      spi-max-frequency = <10000000>;
+
+      reset-gpios = <&gpe 4 GPIO_ACTIVE_LOW>;
+      power-supply = <&lcd_power>;
+
+      backlight = <&backlight>;
+
+      port {
+        panel_input: endpoint {
+          remote-endpoint = <&panel_output>;
+        };
+      };
+    };
-- 
2.33.0


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD
  2021-08-28 11:26 [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Paul Cercueil
@ 2021-08-28 11:26 ` Paul Cercueil
  2021-08-28 14:01   ` Kari Argillander
  2021-08-29 14:59 ` [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Rob Herring
  2021-08-31 13:59 ` Rob Herring
  2 siblings, 1 reply; 6+ messages in thread
From: Paul Cercueil @ 2021-08-28 11:26 UTC (permalink / raw)
  To: Thierry Reding, Sam Ravnborg, Rob Herring
  Cc: Christophe Branchereau, list, dri-devel, devicetree,
	linux-kernel, Paul Cercueil

From: Christophe Branchereau <cbranchereau@gmail.com>

Add driver for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
24-bit TFT LCD with non-square pixels and a delta-RGB 8-bit interface.

Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/gpu/drm/panel/Kconfig               |   8 +
 drivers/gpu/drm/panel/Makefile              |   1 +
 drivers/gpu/drm/panel/panel-auo-a030jtn01.c | 297 ++++++++++++++++++++
 3 files changed, 306 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-auo-a030jtn01.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 0b3784941312..42d42f999266 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -8,6 +8,14 @@ config DRM_PANEL
 menu "Display Panels"
 	depends on DRM && DRM_PANEL
 
+config DRM_PANEL_AUO_A030JTN01
+	tristate "AUO A030JTN01"
+	depends on OF && SPI
+	select REGMAP_SPI
+	help
+	  Say Y here to enable support for the AUO A030JTN01 320x480 3.0" panel
+	  as found in the YLM RS-97 handheld gaming console.
+
 config DRM_PANEL_ABT_Y030XX067A
 	tristate "ABT Y030XX067A 320x480 LCD panel"
 	depends on OF && SPI
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 60c0149fc54a..edf62866e4af 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_DRM_PANEL_AUO_A030JTN01) += panel-auo-a030jtn01.o
 obj-$(CONFIG_DRM_PANEL_ABT_Y030XX067A) += panel-abt-y030xx067a.o
 obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o
 obj-$(CONFIG_DRM_PANEL_ASUS_Z00T_TM5P5_NT35596) += panel-asus-z00t-tm5p5-n35596.o
diff --git a/drivers/gpu/drm/panel/panel-auo-a030jtn01.c b/drivers/gpu/drm/panel/panel-auo-a030jtn01.c
new file mode 100644
index 000000000000..804567a59d19
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-auo-a030jtn01.c
@@ -0,0 +1,297 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AU Optronics A030JTN01.0 TFT LCD panel driver
+ *
+ * Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
+ * Copyright (C) 2020, Christophe Branchereau <cbranchereau@gmail.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+struct a030jtn01_info {
+	const struct drm_display_mode *display_modes;
+	unsigned int num_modes;
+	u16 width_mm, height_mm;
+	u32 bus_format, bus_flags;
+};
+
+struct a030jtn01 {
+	struct drm_panel panel;
+	struct spi_device *spi;
+	struct regmap *map;
+
+	const struct a030jtn01_info *panel_info;
+
+	struct regulator *supply;
+	struct gpio_desc *reset_gpio;
+};
+
+static inline struct a030jtn01 *to_a030jtn01(struct drm_panel *panel)
+{
+	return container_of(panel, struct a030jtn01, panel);
+}
+
+static int a030jtn01_prepare(struct drm_panel *panel)
+{
+	struct a030jtn01 *priv = to_a030jtn01(panel);
+	struct device *dev = &priv->spi->dev;
+	int err;
+
+	err = regulator_enable(priv->supply);
+	if (err) {
+		dev_err(dev, "Failed to enable power supply: %d\n", err);
+		return err;
+	}
+
+	usleep_range(1000, 8000);
+
+	/* Reset the chip */
+	gpiod_set_value_cansleep(priv->reset_gpio, 1);
+	usleep_range(100, 8000);
+	gpiod_set_value_cansleep(priv->reset_gpio, 0);
+	usleep_range(2000, 8000);
+
+	/*
+	 * No idea why two writes are needed. If this write is commented,
+	 * the colors are wrong. Doesn't seem to be timing-related, since
+	 * a msleep(200) doesn't fix it.
+	 */
+	regmap_write(priv->map, 0x06, 0x00);
+
+	/* Use (24 + 6) == 0x1e as the vertical back porch */
+	err = regmap_write(priv->map, 0x06, 0x1e);
+	if (err)
+		goto err_disable_regulator;
+
+	/* Use (42 + 30) * 3 == 0xd8 as the horizontal back porch */
+	err = regmap_write(priv->map, 0x07, 0xd8);
+	if (err)
+		goto err_disable_regulator;
+
+	regmap_write(priv->map, 0x05, 0x74);
+
+	return 0;
+
+err_disable_regulator:
+	gpiod_set_value_cansleep(priv->reset_gpio, 1);
+	regulator_disable(priv->supply);
+	return err;
+}
+
+static int a030jtn01_unprepare(struct drm_panel *panel)
+{
+	struct a030jtn01 *priv = to_a030jtn01(panel);
+
+	gpiod_set_value_cansleep(priv->reset_gpio, 1);
+	regulator_disable(priv->supply);
+
+	return 0;
+}
+
+static int a030jtn01_enable(struct drm_panel *panel)
+{
+	struct a030jtn01 *priv = to_a030jtn01(panel);
+	int ret;
+
+	ret = regmap_write(priv->map, 0x05, 0x75);
+	if (ret)
+		return ret;
+
+	/* Wait for the picture to be stable */
+	if (panel->backlight)
+		msleep(100);
+
+	return 0;
+}
+
+static int a030jtn01_disable(struct drm_panel *panel)
+{
+	struct a030jtn01 *priv = to_a030jtn01(panel);
+
+	return regmap_write(priv->map, 0x05, 0x74);
+}
+
+static int a030jtn01_get_modes(struct drm_panel *panel,
+				struct drm_connector *connector)
+{
+	struct a030jtn01 *priv = to_a030jtn01(panel);
+	const struct a030jtn01_info *panel_info = priv->panel_info;
+	struct drm_display_mode *mode;
+	unsigned int i;
+
+	for (i = 0; i < panel_info->num_modes; i++) {
+		mode = drm_mode_duplicate(connector->dev,
+					  &panel_info->display_modes[i]);
+		if (!mode)
+			return -ENOMEM;
+
+		drm_mode_set_name(mode);
+
+		mode->type = DRM_MODE_TYPE_DRIVER;
+		if (panel_info->num_modes == 1)
+			mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+		drm_mode_probed_add(connector, mode);
+	}
+
+	connector->display_info.bpc = 8;
+	connector->display_info.width_mm = panel_info->width_mm;
+	connector->display_info.height_mm = panel_info->height_mm;
+
+	drm_display_info_set_bus_formats(&connector->display_info,
+					 &panel_info->bus_format, 1);
+	connector->display_info.bus_flags = panel_info->bus_flags;
+
+	return panel_info->num_modes;
+}
+
+static const struct drm_panel_funcs a030jtn01_funcs = {
+	.prepare	= a030jtn01_prepare,
+	.unprepare	= a030jtn01_unprepare,
+	.enable		= a030jtn01_enable,
+	.disable	= a030jtn01_disable,
+	.get_modes	= a030jtn01_get_modes,
+};
+
+static bool a030jtn01_has_reg(struct device *dev, unsigned int reg)
+{
+	static const u32 a030jtn01_regs_mask = 0x001823f1fb;
+
+	return a030jtn01_regs_mask & BIT(reg);
+};
+
+static const struct regmap_config a030jtn01_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.read_flag_mask = 0x40,
+	.max_register = 0x1c,
+	.readable_reg = a030jtn01_has_reg,
+	.writeable_reg = a030jtn01_has_reg,
+};
+
+static int a030jtn01_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct a030jtn01 *priv;
+	int err;
+
+	spi->mode |= SPI_MODE_3 | SPI_3WIRE;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->spi = spi;
+	spi_set_drvdata(spi, priv);
+
+	priv->map = devm_regmap_init_spi(spi, &a030jtn01_regmap_config);
+	if (IS_ERR(priv->map)) {
+		dev_err(dev, "Unable to init regmap\n");
+		return PTR_ERR(priv->map);
+	}
+
+	priv->panel_info = of_device_get_match_data(dev);
+	if (!priv->panel_info)
+		return -EINVAL;
+
+	priv->supply = devm_regulator_get(dev, "power");
+	if (IS_ERR(priv->supply)) {
+		dev_err(dev, "Failed to get power supply\n");
+		return PTR_ERR(priv->supply);
+	}
+
+	priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(priv->reset_gpio)) {
+		dev_err(dev, "Failed to get reset GPIO\n");
+		return PTR_ERR(priv->reset_gpio);
+	}
+
+	drm_panel_init(&priv->panel, dev, &a030jtn01_funcs,
+		       DRM_MODE_CONNECTOR_DPI);
+
+	err = drm_panel_of_backlight(&priv->panel);
+	if (err)
+		return err;
+
+	drm_panel_add(&priv->panel);
+
+	return 0;
+}
+
+static int a030jtn01_remove(struct spi_device *spi)
+{
+	struct a030jtn01 *priv = spi_get_drvdata(spi);
+
+	drm_panel_remove(&priv->panel);
+	drm_panel_disable(&priv->panel);
+	drm_panel_unprepare(&priv->panel);
+
+	return 0;
+}
+
+static const struct drm_display_mode a030jtn01_modes[] = {
+	{ /* 60 Hz */
+		.clock = 14400,
+		.hdisplay = 320,
+		.hsync_start = 320 + 8,
+		.hsync_end = 320 + 8 + 42,
+		.htotal = 320 + 8 + 42 + 30,
+		.vdisplay = 480,
+		.vsync_start = 480 + 90,
+		.vsync_end = 480 + 90 + 24,
+		.vtotal = 480 + 90 + 24 + 6,
+		.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+	},
+	{ /* 50 Hz */
+		.clock = 12000,
+		.hdisplay = 320,
+		.hsync_start = 320 + 8,
+		.hsync_end = 320 + 8 + 42,
+		.htotal = 320 + 8 + 42 + 30,
+		.vdisplay = 480,
+		.vsync_start = 480 + 90,
+		.vsync_end = 480 + 90 + 24,
+		.vtotal = 480 + 90 + 24 + 6,
+		.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+	},
+};
+
+static const struct a030jtn01_info a030jtn01_info = {
+	.display_modes = a030jtn01_modes,
+	.num_modes = ARRAY_SIZE(a030jtn01_modes),
+	.width_mm = 70,
+	.height_mm = 51,
+	.bus_format = MEDIA_BUS_FMT_RGB888_3X8_DELTA,
+	.bus_flags = DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+};
+
+static const struct of_device_id a030jtn01_of_match[] = {
+	{ .compatible = "auo,a030jtn01", .data = &a030jtn01_info },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, a030jtn01_of_match);
+
+static struct spi_driver a030jtn01_driver = {
+	.driver = {
+		.name = "auo-a030jtn01",
+		.of_match_table = a030jtn01_of_match,
+	},
+	.probe = a030jtn01_probe,
+	.remove = a030jtn01_remove,
+};
+module_spi_driver(a030jtn01_driver);
+
+MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
+MODULE_AUTHOR("Christophe Branchereau <cbranchereau@gmail.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.33.0


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD
  2021-08-28 11:26 ` [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD Paul Cercueil
@ 2021-08-28 14:01   ` Kari Argillander
  2021-08-28 14:12     ` Paul Cercueil
  0 siblings, 1 reply; 6+ messages in thread
From: Kari Argillander @ 2021-08-28 14:01 UTC (permalink / raw)
  To: Paul Cercueil
  Cc: Thierry Reding, Sam Ravnborg, Rob Herring,
	Christophe Branchereau, list, dri-devel, devicetree,
	linux-kernel

On Sat, Aug 28, 2021 at 12:26:40PM +0100, Paul Cercueil wrote:
> From: Christophe Branchereau <cbranchereau@gmail.com>
> 
> Add driver for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
> 24-bit TFT LCD with non-square pixels and a delta-RGB 8-bit interface.
> 
> Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  drivers/gpu/drm/panel/Kconfig               |   8 +
>  drivers/gpu/drm/panel/Makefile              |   1 +
>  drivers/gpu/drm/panel/panel-auo-a030jtn01.c | 297 ++++++++++++++++++++
>  3 files changed, 306 insertions(+)
>  create mode 100644 drivers/gpu/drm/panel/panel-auo-a030jtn01.c
> 
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 0b3784941312..42d42f999266 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -8,6 +8,14 @@ config DRM_PANEL
>  menu "Display Panels"
>  	depends on DRM && DRM_PANEL
>  
> +config DRM_PANEL_AUO_A030JTN01
> +	tristate "AUO A030JTN01"
> +	depends on OF && SPI
> +	select REGMAP_SPI
> +	help
> +	  Say Y here to enable support for the AUO A030JTN01 320x480 3.0" panel
> +	  as found in the YLM RS-97 handheld gaming console.
> +

It seems that these should be alphabetical order.

>  config DRM_PANEL_ABT_Y030XX067A
>  	tristate "ABT Y030XX067A 320x480 LCD panel"
>  	depends on OF && SPI
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index 60c0149fc54a..edf62866e4af 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -1,4 +1,5 @@
>  # SPDX-License-Identifier: GPL-2.0
> +obj-$(CONFIG_DRM_PANEL_AUO_A030JTN01) += panel-auo-a030jtn01.o
>  obj-$(CONFIG_DRM_PANEL_ABT_Y030XX067A) += panel-abt-y030xx067a.o
>  obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o
>  obj-$(CONFIG_DRM_PANEL_ASUS_Z00T_TM5P5_NT35596) += panel-asus-z00t-tm5p5-n35596.o
> diff --git a/drivers/gpu/drm/panel/panel-auo-a030jtn01.c b/drivers/gpu/drm/panel/panel-auo-a030jtn01.c
> new file mode 100644
> index 000000000000..804567a59d19
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-auo-a030jtn01.c
> @@ -0,0 +1,297 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * AU Optronics A030JTN01.0 TFT LCD panel driver
> + *
> + * Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
> + * Copyright (C) 2020, Christophe Branchereau <cbranchereau@gmail.com>

Should these be 2021?

    Argillander

> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/media-bus-format.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/spi/spi.h>
> +
> +#include <drm/drm_modes.h>
> +#include <drm/drm_panel.h>
> +
> +struct a030jtn01_info {
> +	const struct drm_display_mode *display_modes;
> +	unsigned int num_modes;
> +	u16 width_mm, height_mm;
> +	u32 bus_format, bus_flags;
> +};
> +
> +struct a030jtn01 {
> +	struct drm_panel panel;
> +	struct spi_device *spi;
> +	struct regmap *map;
> +
> +	const struct a030jtn01_info *panel_info;
> +
> +	struct regulator *supply;
> +	struct gpio_desc *reset_gpio;
> +};
> +
> +static inline struct a030jtn01 *to_a030jtn01(struct drm_panel *panel)
> +{
> +	return container_of(panel, struct a030jtn01, panel);
> +}
> +
> +static int a030jtn01_prepare(struct drm_panel *panel)
> +{
> +	struct a030jtn01 *priv = to_a030jtn01(panel);
> +	struct device *dev = &priv->spi->dev;
> +	int err;
> +
> +	err = regulator_enable(priv->supply);
> +	if (err) {
> +		dev_err(dev, "Failed to enable power supply: %d\n", err);
> +		return err;
> +	}
> +
> +	usleep_range(1000, 8000);
> +
> +	/* Reset the chip */
> +	gpiod_set_value_cansleep(priv->reset_gpio, 1);
> +	usleep_range(100, 8000);
> +	gpiod_set_value_cansleep(priv->reset_gpio, 0);
> +	usleep_range(2000, 8000);
> +
> +	/*
> +	 * No idea why two writes are needed. If this write is commented,
> +	 * the colors are wrong. Doesn't seem to be timing-related, since
> +	 * a msleep(200) doesn't fix it.
> +	 */
> +	regmap_write(priv->map, 0x06, 0x00);
> +
> +	/* Use (24 + 6) == 0x1e as the vertical back porch */
> +	err = regmap_write(priv->map, 0x06, 0x1e);
> +	if (err)
> +		goto err_disable_regulator;
> +
> +	/* Use (42 + 30) * 3 == 0xd8 as the horizontal back porch */
> +	err = regmap_write(priv->map, 0x07, 0xd8);
> +	if (err)
> +		goto err_disable_regulator;
> +
> +	regmap_write(priv->map, 0x05, 0x74);
> +
> +	return 0;
> +
> +err_disable_regulator:
> +	gpiod_set_value_cansleep(priv->reset_gpio, 1);
> +	regulator_disable(priv->supply);
> +	return err;
> +}
> +
> +static int a030jtn01_unprepare(struct drm_panel *panel)
> +{
> +	struct a030jtn01 *priv = to_a030jtn01(panel);
> +
> +	gpiod_set_value_cansleep(priv->reset_gpio, 1);
> +	regulator_disable(priv->supply);
> +
> +	return 0;
> +}
> +
> +static int a030jtn01_enable(struct drm_panel *panel)
> +{
> +	struct a030jtn01 *priv = to_a030jtn01(panel);
> +	int ret;
> +
> +	ret = regmap_write(priv->map, 0x05, 0x75);
> +	if (ret)
> +		return ret;
> +
> +	/* Wait for the picture to be stable */
> +	if (panel->backlight)
> +		msleep(100);
> +
> +	return 0;
> +}
> +
> +static int a030jtn01_disable(struct drm_panel *panel)
> +{
> +	struct a030jtn01 *priv = to_a030jtn01(panel);
> +
> +	return regmap_write(priv->map, 0x05, 0x74);
> +}
> +
> +static int a030jtn01_get_modes(struct drm_panel *panel,
> +				struct drm_connector *connector)
> +{
> +	struct a030jtn01 *priv = to_a030jtn01(panel);
> +	const struct a030jtn01_info *panel_info = priv->panel_info;
> +	struct drm_display_mode *mode;
> +	unsigned int i;
> +
> +	for (i = 0; i < panel_info->num_modes; i++) {
> +		mode = drm_mode_duplicate(connector->dev,
> +					  &panel_info->display_modes[i]);
> +		if (!mode)
> +			return -ENOMEM;
> +
> +		drm_mode_set_name(mode);
> +
> +		mode->type = DRM_MODE_TYPE_DRIVER;
> +		if (panel_info->num_modes == 1)
> +			mode->type |= DRM_MODE_TYPE_PREFERRED;
> +
> +		drm_mode_probed_add(connector, mode);
> +	}
> +
> +	connector->display_info.bpc = 8;
> +	connector->display_info.width_mm = panel_info->width_mm;
> +	connector->display_info.height_mm = panel_info->height_mm;
> +
> +	drm_display_info_set_bus_formats(&connector->display_info,
> +					 &panel_info->bus_format, 1);
> +	connector->display_info.bus_flags = panel_info->bus_flags;
> +
> +	return panel_info->num_modes;
> +}
> +
> +static const struct drm_panel_funcs a030jtn01_funcs = {
> +	.prepare	= a030jtn01_prepare,
> +	.unprepare	= a030jtn01_unprepare,
> +	.enable		= a030jtn01_enable,
> +	.disable	= a030jtn01_disable,
> +	.get_modes	= a030jtn01_get_modes,
> +};
> +
> +static bool a030jtn01_has_reg(struct device *dev, unsigned int reg)
> +{
> +	static const u32 a030jtn01_regs_mask = 0x001823f1fb;
> +
> +	return a030jtn01_regs_mask & BIT(reg);
> +};
> +
> +static const struct regmap_config a030jtn01_regmap_config = {
> +	.reg_bits = 8,
> +	.val_bits = 8,
> +	.read_flag_mask = 0x40,
> +	.max_register = 0x1c,
> +	.readable_reg = a030jtn01_has_reg,
> +	.writeable_reg = a030jtn01_has_reg,
> +};
> +
> +static int a030jtn01_probe(struct spi_device *spi)
> +{
> +	struct device *dev = &spi->dev;
> +	struct a030jtn01 *priv;
> +	int err;
> +
> +	spi->mode |= SPI_MODE_3 | SPI_3WIRE;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->spi = spi;
> +	spi_set_drvdata(spi, priv);
> +
> +	priv->map = devm_regmap_init_spi(spi, &a030jtn01_regmap_config);
> +	if (IS_ERR(priv->map)) {
> +		dev_err(dev, "Unable to init regmap\n");
> +		return PTR_ERR(priv->map);
> +	}
> +
> +	priv->panel_info = of_device_get_match_data(dev);
> +	if (!priv->panel_info)
> +		return -EINVAL;
> +
> +	priv->supply = devm_regulator_get(dev, "power");
> +	if (IS_ERR(priv->supply)) {
> +		dev_err(dev, "Failed to get power supply\n");
> +		return PTR_ERR(priv->supply);
> +	}
> +
> +	priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> +	if (IS_ERR(priv->reset_gpio)) {
> +		dev_err(dev, "Failed to get reset GPIO\n");
> +		return PTR_ERR(priv->reset_gpio);
> +	}
> +
> +	drm_panel_init(&priv->panel, dev, &a030jtn01_funcs,
> +		       DRM_MODE_CONNECTOR_DPI);
> +
> +	err = drm_panel_of_backlight(&priv->panel);
> +	if (err)
> +		return err;
> +
> +	drm_panel_add(&priv->panel);
> +
> +	return 0;
> +}
> +
> +static int a030jtn01_remove(struct spi_device *spi)
> +{
> +	struct a030jtn01 *priv = spi_get_drvdata(spi);
> +
> +	drm_panel_remove(&priv->panel);
> +	drm_panel_disable(&priv->panel);
> +	drm_panel_unprepare(&priv->panel);
> +
> +	return 0;
> +}
> +
> +static const struct drm_display_mode a030jtn01_modes[] = {
> +	{ /* 60 Hz */
> +		.clock = 14400,
> +		.hdisplay = 320,
> +		.hsync_start = 320 + 8,
> +		.hsync_end = 320 + 8 + 42,
> +		.htotal = 320 + 8 + 42 + 30,
> +		.vdisplay = 480,
> +		.vsync_start = 480 + 90,
> +		.vsync_end = 480 + 90 + 24,
> +		.vtotal = 480 + 90 + 24 + 6,
> +		.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> +	},
> +	{ /* 50 Hz */
> +		.clock = 12000,
> +		.hdisplay = 320,
> +		.hsync_start = 320 + 8,
> +		.hsync_end = 320 + 8 + 42,
> +		.htotal = 320 + 8 + 42 + 30,
> +		.vdisplay = 480,
> +		.vsync_start = 480 + 90,
> +		.vsync_end = 480 + 90 + 24,
> +		.vtotal = 480 + 90 + 24 + 6,
> +		.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> +	},
> +};
> +
> +static const struct a030jtn01_info a030jtn01_info = {
> +	.display_modes = a030jtn01_modes,
> +	.num_modes = ARRAY_SIZE(a030jtn01_modes),
> +	.width_mm = 70,
> +	.height_mm = 51,
> +	.bus_format = MEDIA_BUS_FMT_RGB888_3X8_DELTA,
> +	.bus_flags = DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
> +};
> +
> +static const struct of_device_id a030jtn01_of_match[] = {
> +	{ .compatible = "auo,a030jtn01", .data = &a030jtn01_info },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, a030jtn01_of_match);
> +
> +static struct spi_driver a030jtn01_driver = {
> +	.driver = {
> +		.name = "auo-a030jtn01",
> +		.of_match_table = a030jtn01_of_match,
> +	},
> +	.probe = a030jtn01_probe,
> +	.remove = a030jtn01_remove,
> +};
> +module_spi_driver(a030jtn01_driver);
> +
> +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
> +MODULE_AUTHOR("Christophe Branchereau <cbranchereau@gmail.com>");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.33.0
> 

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD
  2021-08-28 14:01   ` Kari Argillander
@ 2021-08-28 14:12     ` Paul Cercueil
  0 siblings, 0 replies; 6+ messages in thread
From: Paul Cercueil @ 2021-08-28 14:12 UTC (permalink / raw)
  To: Kari Argillander
  Cc: Thierry Reding, Sam Ravnborg, Rob Herring,
	Christophe Branchereau, list, dri-devel, devicetree,
	linux-kernel

Hi,

Le sam., août 28 2021 at 17:01:39 +0300, Kari Argillander 
<kari.argillander@gmail.com> a écrit :
> On Sat, Aug 28, 2021 at 12:26:40PM +0100, Paul Cercueil wrote:
>>  From: Christophe Branchereau <cbranchereau@gmail.com>
>> 
>>  Add driver for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
>>  24-bit TFT LCD with non-square pixels and a delta-RGB 8-bit 
>> interface.
>> 
>>  Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
>>  Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>>  ---
>>   drivers/gpu/drm/panel/Kconfig               |   8 +
>>   drivers/gpu/drm/panel/Makefile              |   1 +
>>   drivers/gpu/drm/panel/panel-auo-a030jtn01.c | 297 
>> ++++++++++++++++++++
>>   3 files changed, 306 insertions(+)
>>   create mode 100644 drivers/gpu/drm/panel/panel-auo-a030jtn01.c
>> 
>>  diff --git a/drivers/gpu/drm/panel/Kconfig 
>> b/drivers/gpu/drm/panel/Kconfig
>>  index 0b3784941312..42d42f999266 100644
>>  --- a/drivers/gpu/drm/panel/Kconfig
>>  +++ b/drivers/gpu/drm/panel/Kconfig
>>  @@ -8,6 +8,14 @@ config DRM_PANEL
>>   menu "Display Panels"
>>   	depends on DRM && DRM_PANEL
>> 
>>  +config DRM_PANEL_AUO_A030JTN01
>>  +	tristate "AUO A030JTN01"
>>  +	depends on OF && SPI
>>  +	select REGMAP_SPI
>>  +	help
>>  +	  Say Y here to enable support for the AUO A030JTN01 320x480 3.0" 
>> panel
>>  +	  as found in the YLM RS-97 handheld gaming console.
>>  +
> 
> It seems that these should be alphabetical order.

You're totally right, sorry about that.

>>   config DRM_PANEL_ABT_Y030XX067A
>>   	tristate "ABT Y030XX067A 320x480 LCD panel"
>>   	depends on OF && SPI
>>  diff --git a/drivers/gpu/drm/panel/Makefile 
>> b/drivers/gpu/drm/panel/Makefile
>>  index 60c0149fc54a..edf62866e4af 100644
>>  --- a/drivers/gpu/drm/panel/Makefile
>>  +++ b/drivers/gpu/drm/panel/Makefile
>>  @@ -1,4 +1,5 @@
>>   # SPDX-License-Identifier: GPL-2.0
>>  +obj-$(CONFIG_DRM_PANEL_AUO_A030JTN01) += panel-auo-a030jtn01.o
>>   obj-$(CONFIG_DRM_PANEL_ABT_Y030XX067A) += panel-abt-y030xx067a.o
>>   obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o
>>   obj-$(CONFIG_DRM_PANEL_ASUS_Z00T_TM5P5_NT35596) += 
>> panel-asus-z00t-tm5p5-n35596.o
>>  diff --git a/drivers/gpu/drm/panel/panel-auo-a030jtn01.c 
>> b/drivers/gpu/drm/panel/panel-auo-a030jtn01.c
>>  new file mode 100644
>>  index 000000000000..804567a59d19
>>  --- /dev/null
>>  +++ b/drivers/gpu/drm/panel/panel-auo-a030jtn01.c
>>  @@ -0,0 +1,297 @@
>>  +// SPDX-License-Identifier: GPL-2.0
>>  +/*
>>  + * AU Optronics A030JTN01.0 TFT LCD panel driver
>>  + *
>>  + * Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
>>  + * Copyright (C) 2020, Christophe Branchereau 
>> <cbranchereau@gmail.com>
> 
> Should these be 2021?

The commits were written in 2021, but I guess I can update the date, 
yes.

Cheers,
-Paul

>     Argillander
> 
>>  + */
>>  +
>>  +#include <linux/delay.h>
>>  +#include <linux/device.h>
>>  +#include <linux/gpio/consumer.h>
>>  +#include <linux/media-bus-format.h>
>>  +#include <linux/module.h>
>>  +#include <linux/of_device.h>
>>  +#include <linux/regmap.h>
>>  +#include <linux/regulator/consumer.h>
>>  +#include <linux/spi/spi.h>
>>  +
>>  +#include <drm/drm_modes.h>
>>  +#include <drm/drm_panel.h>
>>  +
>>  +struct a030jtn01_info {
>>  +	const struct drm_display_mode *display_modes;
>>  +	unsigned int num_modes;
>>  +	u16 width_mm, height_mm;
>>  +	u32 bus_format, bus_flags;
>>  +};
>>  +
>>  +struct a030jtn01 {
>>  +	struct drm_panel panel;
>>  +	struct spi_device *spi;
>>  +	struct regmap *map;
>>  +
>>  +	const struct a030jtn01_info *panel_info;
>>  +
>>  +	struct regulator *supply;
>>  +	struct gpio_desc *reset_gpio;
>>  +};
>>  +
>>  +static inline struct a030jtn01 *to_a030jtn01(struct drm_panel 
>> *panel)
>>  +{
>>  +	return container_of(panel, struct a030jtn01, panel);
>>  +}
>>  +
>>  +static int a030jtn01_prepare(struct drm_panel *panel)
>>  +{
>>  +	struct a030jtn01 *priv = to_a030jtn01(panel);
>>  +	struct device *dev = &priv->spi->dev;
>>  +	int err;
>>  +
>>  +	err = regulator_enable(priv->supply);
>>  +	if (err) {
>>  +		dev_err(dev, "Failed to enable power supply: %d\n", err);
>>  +		return err;
>>  +	}
>>  +
>>  +	usleep_range(1000, 8000);
>>  +
>>  +	/* Reset the chip */
>>  +	gpiod_set_value_cansleep(priv->reset_gpio, 1);
>>  +	usleep_range(100, 8000);
>>  +	gpiod_set_value_cansleep(priv->reset_gpio, 0);
>>  +	usleep_range(2000, 8000);
>>  +
>>  +	/*
>>  +	 * No idea why two writes are needed. If this write is commented,
>>  +	 * the colors are wrong. Doesn't seem to be timing-related, since
>>  +	 * a msleep(200) doesn't fix it.
>>  +	 */
>>  +	regmap_write(priv->map, 0x06, 0x00);
>>  +
>>  +	/* Use (24 + 6) == 0x1e as the vertical back porch */
>>  +	err = regmap_write(priv->map, 0x06, 0x1e);
>>  +	if (err)
>>  +		goto err_disable_regulator;
>>  +
>>  +	/* Use (42 + 30) * 3 == 0xd8 as the horizontal back porch */
>>  +	err = regmap_write(priv->map, 0x07, 0xd8);
>>  +	if (err)
>>  +		goto err_disable_regulator;
>>  +
>>  +	regmap_write(priv->map, 0x05, 0x74);
>>  +
>>  +	return 0;
>>  +
>>  +err_disable_regulator:
>>  +	gpiod_set_value_cansleep(priv->reset_gpio, 1);
>>  +	regulator_disable(priv->supply);
>>  +	return err;
>>  +}
>>  +
>>  +static int a030jtn01_unprepare(struct drm_panel *panel)
>>  +{
>>  +	struct a030jtn01 *priv = to_a030jtn01(panel);
>>  +
>>  +	gpiod_set_value_cansleep(priv->reset_gpio, 1);
>>  +	regulator_disable(priv->supply);
>>  +
>>  +	return 0;
>>  +}
>>  +
>>  +static int a030jtn01_enable(struct drm_panel *panel)
>>  +{
>>  +	struct a030jtn01 *priv = to_a030jtn01(panel);
>>  +	int ret;
>>  +
>>  +	ret = regmap_write(priv->map, 0x05, 0x75);
>>  +	if (ret)
>>  +		return ret;
>>  +
>>  +	/* Wait for the picture to be stable */
>>  +	if (panel->backlight)
>>  +		msleep(100);
>>  +
>>  +	return 0;
>>  +}
>>  +
>>  +static int a030jtn01_disable(struct drm_panel *panel)
>>  +{
>>  +	struct a030jtn01 *priv = to_a030jtn01(panel);
>>  +
>>  +	return regmap_write(priv->map, 0x05, 0x74);
>>  +}
>>  +
>>  +static int a030jtn01_get_modes(struct drm_panel *panel,
>>  +				struct drm_connector *connector)
>>  +{
>>  +	struct a030jtn01 *priv = to_a030jtn01(panel);
>>  +	const struct a030jtn01_info *panel_info = priv->panel_info;
>>  +	struct drm_display_mode *mode;
>>  +	unsigned int i;
>>  +
>>  +	for (i = 0; i < panel_info->num_modes; i++) {
>>  +		mode = drm_mode_duplicate(connector->dev,
>>  +					  &panel_info->display_modes[i]);
>>  +		if (!mode)
>>  +			return -ENOMEM;
>>  +
>>  +		drm_mode_set_name(mode);
>>  +
>>  +		mode->type = DRM_MODE_TYPE_DRIVER;
>>  +		if (panel_info->num_modes == 1)
>>  +			mode->type |= DRM_MODE_TYPE_PREFERRED;
>>  +
>>  +		drm_mode_probed_add(connector, mode);
>>  +	}
>>  +
>>  +	connector->display_info.bpc = 8;
>>  +	connector->display_info.width_mm = panel_info->width_mm;
>>  +	connector->display_info.height_mm = panel_info->height_mm;
>>  +
>>  +	drm_display_info_set_bus_formats(&connector->display_info,
>>  +					 &panel_info->bus_format, 1);
>>  +	connector->display_info.bus_flags = panel_info->bus_flags;
>>  +
>>  +	return panel_info->num_modes;
>>  +}
>>  +
>>  +static const struct drm_panel_funcs a030jtn01_funcs = {
>>  +	.prepare	= a030jtn01_prepare,
>>  +	.unprepare	= a030jtn01_unprepare,
>>  +	.enable		= a030jtn01_enable,
>>  +	.disable	= a030jtn01_disable,
>>  +	.get_modes	= a030jtn01_get_modes,
>>  +};
>>  +
>>  +static bool a030jtn01_has_reg(struct device *dev, unsigned int reg)
>>  +{
>>  +	static const u32 a030jtn01_regs_mask = 0x001823f1fb;
>>  +
>>  +	return a030jtn01_regs_mask & BIT(reg);
>>  +};
>>  +
>>  +static const struct regmap_config a030jtn01_regmap_config = {
>>  +	.reg_bits = 8,
>>  +	.val_bits = 8,
>>  +	.read_flag_mask = 0x40,
>>  +	.max_register = 0x1c,
>>  +	.readable_reg = a030jtn01_has_reg,
>>  +	.writeable_reg = a030jtn01_has_reg,
>>  +};
>>  +
>>  +static int a030jtn01_probe(struct spi_device *spi)
>>  +{
>>  +	struct device *dev = &spi->dev;
>>  +	struct a030jtn01 *priv;
>>  +	int err;
>>  +
>>  +	spi->mode |= SPI_MODE_3 | SPI_3WIRE;
>>  +
>>  +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>>  +	if (!priv)
>>  +		return -ENOMEM;
>>  +
>>  +	priv->spi = spi;
>>  +	spi_set_drvdata(spi, priv);
>>  +
>>  +	priv->map = devm_regmap_init_spi(spi, &a030jtn01_regmap_config);
>>  +	if (IS_ERR(priv->map)) {
>>  +		dev_err(dev, "Unable to init regmap\n");
>>  +		return PTR_ERR(priv->map);
>>  +	}
>>  +
>>  +	priv->panel_info = of_device_get_match_data(dev);
>>  +	if (!priv->panel_info)
>>  +		return -EINVAL;
>>  +
>>  +	priv->supply = devm_regulator_get(dev, "power");
>>  +	if (IS_ERR(priv->supply)) {
>>  +		dev_err(dev, "Failed to get power supply\n");
>>  +		return PTR_ERR(priv->supply);
>>  +	}
>>  +
>>  +	priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
>>  +	if (IS_ERR(priv->reset_gpio)) {
>>  +		dev_err(dev, "Failed to get reset GPIO\n");
>>  +		return PTR_ERR(priv->reset_gpio);
>>  +	}
>>  +
>>  +	drm_panel_init(&priv->panel, dev, &a030jtn01_funcs,
>>  +		       DRM_MODE_CONNECTOR_DPI);
>>  +
>>  +	err = drm_panel_of_backlight(&priv->panel);
>>  +	if (err)
>>  +		return err;
>>  +
>>  +	drm_panel_add(&priv->panel);
>>  +
>>  +	return 0;
>>  +}
>>  +
>>  +static int a030jtn01_remove(struct spi_device *spi)
>>  +{
>>  +	struct a030jtn01 *priv = spi_get_drvdata(spi);
>>  +
>>  +	drm_panel_remove(&priv->panel);
>>  +	drm_panel_disable(&priv->panel);
>>  +	drm_panel_unprepare(&priv->panel);
>>  +
>>  +	return 0;
>>  +}
>>  +
>>  +static const struct drm_display_mode a030jtn01_modes[] = {
>>  +	{ /* 60 Hz */
>>  +		.clock = 14400,
>>  +		.hdisplay = 320,
>>  +		.hsync_start = 320 + 8,
>>  +		.hsync_end = 320 + 8 + 42,
>>  +		.htotal = 320 + 8 + 42 + 30,
>>  +		.vdisplay = 480,
>>  +		.vsync_start = 480 + 90,
>>  +		.vsync_end = 480 + 90 + 24,
>>  +		.vtotal = 480 + 90 + 24 + 6,
>>  +		.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
>>  +	},
>>  +	{ /* 50 Hz */
>>  +		.clock = 12000,
>>  +		.hdisplay = 320,
>>  +		.hsync_start = 320 + 8,
>>  +		.hsync_end = 320 + 8 + 42,
>>  +		.htotal = 320 + 8 + 42 + 30,
>>  +		.vdisplay = 480,
>>  +		.vsync_start = 480 + 90,
>>  +		.vsync_end = 480 + 90 + 24,
>>  +		.vtotal = 480 + 90 + 24 + 6,
>>  +		.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
>>  +	},
>>  +};
>>  +
>>  +static const struct a030jtn01_info a030jtn01_info = {
>>  +	.display_modes = a030jtn01_modes,
>>  +	.num_modes = ARRAY_SIZE(a030jtn01_modes),
>>  +	.width_mm = 70,
>>  +	.height_mm = 51,
>>  +	.bus_format = MEDIA_BUS_FMT_RGB888_3X8_DELTA,
>>  +	.bus_flags = DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
>>  +};
>>  +
>>  +static const struct of_device_id a030jtn01_of_match[] = {
>>  +	{ .compatible = "auo,a030jtn01", .data = &a030jtn01_info },
>>  +	{ /* sentinel */ }
>>  +};
>>  +MODULE_DEVICE_TABLE(of, a030jtn01_of_match);
>>  +
>>  +static struct spi_driver a030jtn01_driver = {
>>  +	.driver = {
>>  +		.name = "auo-a030jtn01",
>>  +		.of_match_table = a030jtn01_of_match,
>>  +	},
>>  +	.probe = a030jtn01_probe,
>>  +	.remove = a030jtn01_remove,
>>  +};
>>  +module_spi_driver(a030jtn01_driver);
>>  +
>>  +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
>>  +MODULE_AUTHOR("Christophe Branchereau <cbranchereau@gmail.com>");
>>  +MODULE_LICENSE("GPL v2");
>>  --
>>  2.33.0
>> 



^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01
  2021-08-28 11:26 [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Paul Cercueil
  2021-08-28 11:26 ` [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD Paul Cercueil
@ 2021-08-29 14:59 ` Rob Herring
  2021-08-31 13:59 ` Rob Herring
  2 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2021-08-29 14:59 UTC (permalink / raw)
  To: Paul Cercueil
  Cc: devicetree, Rob Herring, Christophe Branchereau, Sam Ravnborg,
	list, dri-devel, Thierry Reding, linux-kernel

On Sat, 28 Aug 2021 12:26:39 +0100, Paul Cercueil wrote:
> Add binding for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
> 24-bit TFT LCD panel with non-square pixels and a delta-RGB 8-bit
> interface.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  .../bindings/display/panel/auo,a030jtn01.yaml | 57 +++++++++++++++++++
>  1 file changed, 57 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dts:23.11-21: Warning (reg_format): /example-0/panel@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dt.yaml: Warning (pci_device_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dt.yaml: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.example.dt.yaml: example-0: panel@0:reg:0: [0] is too short
	From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1521878

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01
  2021-08-28 11:26 [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Paul Cercueil
  2021-08-28 11:26 ` [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD Paul Cercueil
  2021-08-29 14:59 ` [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Rob Herring
@ 2021-08-31 13:59 ` Rob Herring
  2 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2021-08-31 13:59 UTC (permalink / raw)
  To: Paul Cercueil
  Cc: Thierry Reding, Sam Ravnborg, Christophe Branchereau, list,
	dri-devel, devicetree, linux-kernel

On Sat, Aug 28, 2021 at 12:26:39PM +0100, Paul Cercueil wrote:
> Add binding for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
> 24-bit TFT LCD panel with non-square pixels and a delta-RGB 8-bit
> interface.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  .../bindings/display/panel/auo,a030jtn01.yaml | 57 +++++++++++++++++++
>  1 file changed, 57 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml

This appears to be panel-simple.yaml plus 'reg' (and potentially other 
SPI properties). Perhaps rename to panel-simple-spi.yaml? Maybe there's 
others already?

> 
> diff --git a/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml b/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml
> new file mode 100644
> index 000000000000..21c9d62e3625
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/auo,a030jtn01.yaml
> @@ -0,0 +1,57 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/panel/auo,a030jtn01.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: AUO A030JTN01 3.0" (320x480 pixels) 24-bit TFT LCD
> +
> +description: |
> +  The panel must obey the rules for a SPI slave device as specified in
> +  spi/spi-controller.yaml
> +
> +maintainers:
> +  - Paul Cercueil <paul@crapouillou.net>
> +
> +allOf:
> +  - $ref: panel-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: auo,a030jtn01
> +
> +  backlight: true
> +  port: true
> +  power-supply: true
> +  reg: true
> +  reset-gpios: true
> +
> +required:
> +  - compatible
> +  - reg
> +  - power-supply
> +  - reset-gpios
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    panel@0 {
> +      compatible = "auo,a030jtn01";
> +      reg = <0>;
> +
> +      spi-max-frequency = <10000000>;
> +
> +      reset-gpios = <&gpe 4 GPIO_ACTIVE_LOW>;
> +      power-supply = <&lcd_power>;
> +
> +      backlight = <&backlight>;
> +
> +      port {
> +        panel_input: endpoint {
> +          remote-endpoint = <&panel_output>;
> +        };
> +      };
> +    };
> -- 
> 2.33.0
> 
> 

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2021-08-31 14:00 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-28 11:26 [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Paul Cercueil
2021-08-28 11:26 ` [PATCH 2/2] drm/panel: Add driver for the AUO A030JTN01 TFT LCD Paul Cercueil
2021-08-28 14:01   ` Kari Argillander
2021-08-28 14:12     ` Paul Cercueil
2021-08-29 14:59 ` [PATCH 1/2] dt-bindings: display/panel: Add AUO A030JTN01 Rob Herring
2021-08-31 13:59 ` Rob Herring

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).