LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: "Gabriel L. Somlo" <gsomlo@gmail.com>
To: Joel Stanley <joel@jms.id.au>
Cc: "David S . Miller" <davem@davemloft.net>,
	Jakub Kicinski <kuba@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Karol Gugala <kgugala@antmicro.com>,
	Mateusz Holenko <mholenko@antmicro.com>,
	devicetree@vger.kernel.org,
	Florent Kermarrec <florent@enjoy-digital.fr>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	David Shah <dave@ds0.me>, Stafford Horne <shorne@gmail.com>
Subject: Re: [PATCH v3 2/2] net: Add driver for LiteX's LiteETH network interface
Date: Wed, 25 Aug 2021 18:04:47 -0400	[thread overview]
Message-ID: <YSa+f7yeE4ZGQiuX@errol.ini.cmu.edu> (raw)
In-Reply-To: <20210825124655.3104348-3-joel@jms.id.au>

On Wed, Aug 25, 2021 at 10:16:55PM +0930, Joel Stanley wrote:
> LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic
> network device that is commonly used in LiteX designs.
> 
> The driver was first written in 2017 and has been maintained by the
> LiteX community in various trees. Thank you to all who have contributed.
> 
> Co-developed-by: Gabriel Somlo <gsomlo@gmail.com>
> Co-developed-by: David Shah <dave@ds0.me>
> Co-developed-by: Stafford Horne <shorne@gmail.com>
> Signed-off-by: Joel Stanley <joel@jms.id.au>
> ---
> v2:
>  - check for bad len in liteeth_rx before getting skb
>  - use netdev_alloc_skb_ip_align
>  - remove unused duplex/speed and mii_bus variables
>  - set carrier off when stopping device
>  - increment packet count in the same place as bytes
>  - fix error return code when irq could not be found
>  - remove request of mdio base address until it is used
>  - fix of_property_read line wrapping/alignment
>  - only check that reader isn't busy, and then send off next packet
>  - drop third reset
>  - Add an description to the kconfig text
>  - stop tx queue when busy and re-start after tx complete irq fires
>  - use litex accessors to support big endain socs
>  - clean up unused includes
>  - use standard fifo-depth properties, which are in bytes
> v3:
>  - make fifo helper static
>  - fix error messages about invalid slot sizes
>  - use slot size from device tree instead of inferring it
>  - update to match the latest version of the bindings, which describes
>    the number of slots

LGTM -- thanks!

Tested-and-reviewed-by: Gabriel Somlo <gsomlo@gmail.com>

> ---
>  drivers/net/ethernet/Kconfig               |   1 +
>  drivers/net/ethernet/Makefile              |   1 +
>  drivers/net/ethernet/litex/Kconfig         |  27 ++
>  drivers/net/ethernet/litex/Makefile        |   5 +
>  drivers/net/ethernet/litex/litex_liteeth.c | 317 +++++++++++++++++++++
>  5 files changed, 351 insertions(+)
>  create mode 100644 drivers/net/ethernet/litex/Kconfig
>  create mode 100644 drivers/net/ethernet/litex/Makefile
>  create mode 100644 drivers/net/ethernet/litex/litex_liteeth.c
> 
> diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
> index 1cdff1dca790..d796684ec9ca 100644
> --- a/drivers/net/ethernet/Kconfig
> +++ b/drivers/net/ethernet/Kconfig
> @@ -118,6 +118,7 @@ config LANTIQ_XRX200
>  	  Support for the PMAC of the Gigabit switch (GSWIP) inside the
>  	  Lantiq / Intel VRX200 VDSL SoC
>  
> +source "drivers/net/ethernet/litex/Kconfig"
>  source "drivers/net/ethernet/marvell/Kconfig"
>  source "drivers/net/ethernet/mediatek/Kconfig"
>  source "drivers/net/ethernet/mellanox/Kconfig"
> diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
> index cb3f9084a21b..aaa5078cd7d1 100644
> --- a/drivers/net/ethernet/Makefile
> +++ b/drivers/net/ethernet/Makefile
> @@ -51,6 +51,7 @@ obj-$(CONFIG_JME) += jme.o
>  obj-$(CONFIG_KORINA) += korina.o
>  obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
>  obj-$(CONFIG_LANTIQ_XRX200) += lantiq_xrx200.o
> +obj-$(CONFIG_NET_VENDOR_LITEX) += litex/
>  obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
>  obj-$(CONFIG_NET_VENDOR_MEDIATEK) += mediatek/
>  obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
> diff --git a/drivers/net/ethernet/litex/Kconfig b/drivers/net/ethernet/litex/Kconfig
> new file mode 100644
> index 000000000000..265dba414b41
> --- /dev/null
> +++ b/drivers/net/ethernet/litex/Kconfig
> @@ -0,0 +1,27 @@
> +#
> +# LiteX device configuration
> +#
> +
> +config NET_VENDOR_LITEX
> +	bool "LiteX devices"
> +	default y
> +	help
> +	  If you have a network (Ethernet) card belonging to this class, say Y.
> +
> +	  Note that the answer to this question doesn't directly affect the
> +	  kernel: saying N will just cause the configurator to skip all
> +	  the questions about LiteX devices. If you say Y, you will be asked
> +	  for your specific card in the following questions.
> +
> +if NET_VENDOR_LITEX
> +
> +config LITEX_LITEETH
> +	tristate "LiteX Ethernet support"
> +	help
> +	  If you wish to compile a kernel for hardware with a LiteX LiteEth
> +	  device then you should answer Y to this.
> +
> +	  LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic
> +	  network device that is commonly used in LiteX designs.
> +
> +endif # NET_VENDOR_LITEX
> diff --git a/drivers/net/ethernet/litex/Makefile b/drivers/net/ethernet/litex/Makefile
> new file mode 100644
> index 000000000000..9343b73b8e49
> --- /dev/null
> +++ b/drivers/net/ethernet/litex/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for the LiteX network device drivers.
> +#
> +
> +obj-$(CONFIG_LITEX_LITEETH) += litex_liteeth.o
> diff --git a/drivers/net/ethernet/litex/litex_liteeth.c b/drivers/net/ethernet/litex/litex_liteeth.c
> new file mode 100644
> index 000000000000..10e6f2dedfad
> --- /dev/null
> +++ b/drivers/net/ethernet/litex/litex_liteeth.c
> @@ -0,0 +1,317 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * LiteX Liteeth Ethernet
> + *
> + * Copyright 2017 Joel Stanley <joel@jms.id.au>
> + *
> + */
> +
> +#include <linux/etherdevice.h>
> +#include <linux/interrupt.h>
> +#include <linux/litex.h>
> +#include <linux/module.h>
> +#include <linux/of_net.h>
> +#include <linux/platform_device.h>
> +
> +#define LITEETH_WRITER_SLOT       0x00
> +#define LITEETH_WRITER_LENGTH     0x04
> +#define LITEETH_WRITER_ERRORS     0x08
> +#define LITEETH_WRITER_EV_STATUS  0x0C
> +#define LITEETH_WRITER_EV_PENDING 0x10
> +#define LITEETH_WRITER_EV_ENABLE  0x14
> +#define LITEETH_READER_START      0x18
> +#define LITEETH_READER_READY      0x1C
> +#define LITEETH_READER_LEVEL      0x20
> +#define LITEETH_READER_SLOT       0x24
> +#define LITEETH_READER_LENGTH     0x28
> +#define LITEETH_READER_EV_STATUS  0x2C
> +#define LITEETH_READER_EV_PENDING 0x30
> +#define LITEETH_READER_EV_ENABLE  0x34
> +#define LITEETH_PREAMBLE_CRC      0x38
> +#define LITEETH_PREAMBLE_ERRORS   0x3C
> +#define LITEETH_CRC_ERRORS        0x40
> +
> +#define LITEETH_PHY_CRG_RESET     0x00
> +#define LITEETH_MDIO_W            0x04
> +#define LITEETH_MDIO_R            0x0C
> +
> +#define DRV_NAME	"liteeth"
> +
> +struct liteeth {
> +	void __iomem *base;
> +	struct net_device *netdev;
> +	struct device *dev;
> +	u32 slot_size;
> +
> +	/* Tx */
> +	u32 tx_slot;
> +	u32 num_tx_slots;
> +	void __iomem *tx_base;
> +
> +	/* Rx */
> +	u32 rx_slot;
> +	u32 num_rx_slots;
> +	void __iomem *rx_base;
> +};
> +
> +static int liteeth_rx(struct net_device *netdev)
> +{
> +	struct liteeth *priv = netdev_priv(netdev);
> +	struct sk_buff *skb;
> +	unsigned char *data;
> +	u8 rx_slot;
> +	int len;
> +
> +	rx_slot = litex_read8(priv->base + LITEETH_WRITER_SLOT);
> +	len = litex_read32(priv->base + LITEETH_WRITER_LENGTH);
> +
> +	if (len == 0 || len > 2048)
> +		goto rx_drop;
> +
> +	skb = netdev_alloc_skb_ip_align(netdev, len);
> +	if (!skb) {
> +		netdev_err(netdev, "couldn't get memory\n");
> +		goto rx_drop;
> +	}
> +
> +	data = skb_put(skb, len);
> +	memcpy_fromio(data, priv->rx_base + rx_slot * priv->slot_size, len);
> +	skb->protocol = eth_type_trans(skb, netdev);
> +
> +	netdev->stats.rx_packets++;
> +	netdev->stats.rx_bytes += len;
> +
> +	return netif_rx(skb);
> +
> +rx_drop:
> +	netdev->stats.rx_dropped++;
> +	netdev->stats.rx_errors++;
> +
> +	return NET_RX_DROP;
> +}
> +
> +static irqreturn_t liteeth_interrupt(int irq, void *dev_id)
> +{
> +	struct net_device *netdev = dev_id;
> +	struct liteeth *priv = netdev_priv(netdev);
> +	u8 reg;
> +
> +	reg = litex_read8(priv->base + LITEETH_READER_EV_PENDING);
> +	if (reg) {
> +		if (netif_queue_stopped(netdev))
> +			netif_wake_queue(netdev);
> +		litex_write8(priv->base + LITEETH_READER_EV_PENDING, reg);
> +	}
> +
> +	reg = litex_read8(priv->base + LITEETH_WRITER_EV_PENDING);
> +	if (reg) {
> +		liteeth_rx(netdev);
> +		litex_write8(priv->base + LITEETH_WRITER_EV_PENDING, reg);
> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int liteeth_open(struct net_device *netdev)
> +{
> +	struct liteeth *priv = netdev_priv(netdev);
> +	int err;
> +
> +	/* Clear pending events */
> +	litex_write8(priv->base + LITEETH_WRITER_EV_PENDING, 1);
> +	litex_write8(priv->base + LITEETH_READER_EV_PENDING, 1);
> +
> +	err = request_irq(netdev->irq, liteeth_interrupt, 0, netdev->name, netdev);
> +	if (err) {
> +		netdev_err(netdev, "failed to request irq %d\n", netdev->irq);
> +		return err;
> +	}
> +
> +	/* Enable IRQs */
> +	litex_write8(priv->base + LITEETH_WRITER_EV_ENABLE, 1);
> +	litex_write8(priv->base + LITEETH_READER_EV_ENABLE, 1);
> +
> +	netif_carrier_on(netdev);
> +	netif_start_queue(netdev);
> +
> +	return 0;
> +}
> +
> +static int liteeth_stop(struct net_device *netdev)
> +{
> +	struct liteeth *priv = netdev_priv(netdev);
> +
> +	netif_stop_queue(netdev);
> +	netif_carrier_off(netdev);
> +
> +	litex_write8(priv->base + LITEETH_WRITER_EV_ENABLE, 0);
> +	litex_write8(priv->base + LITEETH_READER_EV_ENABLE, 0);
> +
> +	free_irq(netdev->irq, netdev);
> +
> +	return 0;
> +}
> +
> +static int liteeth_start_xmit(struct sk_buff *skb, struct net_device *netdev)
> +{
> +	struct liteeth *priv = netdev_priv(netdev);
> +	void __iomem *txbuffer;
> +
> +	if (!litex_read8(priv->base + LITEETH_READER_READY)) {
> +		if (net_ratelimit())
> +			netdev_err(netdev, "LITEETH_READER_READY not ready\n");
> +
> +		netif_stop_queue(netdev);
> +
> +		return NETDEV_TX_BUSY;
> +	}
> +
> +	/* Reject oversize packets */
> +	if (unlikely(skb->len > priv->slot_size)) {
> +		if (net_ratelimit())
> +			netdev_err(netdev, "tx packet too big\n");
> +
> +		dev_kfree_skb_any(skb);
> +		netdev->stats.tx_dropped++;
> +		netdev->stats.tx_errors++;
> +
> +		return NETDEV_TX_OK;
> +	}
> +
> +	txbuffer = priv->tx_base + priv->tx_slot * priv->slot_size;
> +	memcpy_toio(txbuffer, skb->data, skb->len);
> +	litex_write8(priv->base + LITEETH_READER_SLOT, priv->tx_slot);
> +	litex_write16(priv->base + LITEETH_READER_LENGTH, skb->len);
> +	litex_write8(priv->base + LITEETH_READER_START, 1);
> +
> +	netdev->stats.tx_bytes += skb->len;
> +	netdev->stats.tx_packets++;
> +
> +	priv->tx_slot = (priv->tx_slot + 1) % priv->num_tx_slots;
> +	dev_kfree_skb_any(skb);
> +
> +	return NETDEV_TX_OK;
> +}
> +
> +static const struct net_device_ops liteeth_netdev_ops = {
> +	.ndo_open		= liteeth_open,
> +	.ndo_stop		= liteeth_stop,
> +	.ndo_start_xmit         = liteeth_start_xmit,
> +};
> +
> +static void liteeth_setup_slots(struct liteeth *priv)
> +{
> +	struct device_node *np = priv->dev->of_node;
> +	int err;
> +
> +	err = of_property_read_u32(np, "litex,rx-slots", &priv->num_rx_slots);
> +	if (err) {
> +		dev_dbg(priv->dev, "unable to get litex,rx-slots, using 2\n");
> +		priv->num_rx_slots = 2;
> +	}
> +
> +	err = of_property_read_u32(np, "litex,tx-slots", &priv->num_tx_slots);
> +	if (err) {
> +		dev_dbg(priv->dev, "unable to get litex,tx-slots, using 2\n");
> +		priv->num_tx_slots = 2;
> +	}
> +
> +	err = of_property_read_u32(np, "litex,slot-size", &priv->slot_size);
> +	if (err) {
> +		dev_dbg(priv->dev, "unable to get litex,slot-size, using 0x800\n");
> +		priv->slot_size = 0x800;
> +	}
> +}
> +
> +static int liteeth_probe(struct platform_device *pdev)
> +{
> +	struct net_device *netdev;
> +	void __iomem *buf_base;
> +	struct resource *res;
> +	struct liteeth *priv;
> +	int irq, err;
> +
> +	netdev = devm_alloc_etherdev(&pdev->dev, sizeof(*priv));
> +	if (!netdev)
> +		return -ENOMEM;
> +
> +	SET_NETDEV_DEV(netdev, &pdev->dev);
> +	platform_set_drvdata(pdev, netdev);
> +
> +	priv = netdev_priv(netdev);
> +	priv->netdev = netdev;
> +	priv->dev = &pdev->dev;
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0) {
> +		dev_err(&pdev->dev, "Failed to get IRQ %d\n", irq);
> +		return irq;
> +	}
> +	netdev->irq = irq;
> +
> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mac");
> +	priv->base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(priv->base))
> +		return PTR_ERR(priv->base);
> +
> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "buffer");
> +	buf_base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(buf_base))
> +		return PTR_ERR(buf_base);
> +
> +	liteeth_setup_slots(priv);
> +
> +	/* Rx slots */
> +	priv->rx_base = buf_base;
> +	priv->rx_slot = 0;
> +
> +	/* Tx slots come after Rx slots */
> +	priv->tx_base = buf_base + priv->num_rx_slots * priv->slot_size;
> +	priv->tx_slot = 0;
> +
> +	err = of_get_mac_address(pdev->dev.of_node, netdev->dev_addr);
> +	if (err)
> +		eth_hw_addr_random(netdev);
> +
> +	netdev->netdev_ops = &liteeth_netdev_ops;
> +
> +	err = register_netdev(netdev);
> +	if (err) {
> +		dev_err(&pdev->dev, "Failed to register netdev %d\n", err);
> +		return err;
> +	}
> +
> +	netdev_info(netdev, "irq %d slots: tx %d rx %d size %d\n",
> +		    netdev->irq, priv->num_tx_slots, priv->num_rx_slots, priv->slot_size);
> +
> +	return 0;
> +}
> +
> +static int liteeth_remove(struct platform_device *pdev)
> +{
> +	struct net_device *netdev = platform_get_drvdata(pdev);
> +
> +	unregister_netdev(netdev);
> +	free_netdev(netdev);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id liteeth_of_match[] = {
> +	{ .compatible = "litex,liteeth" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, liteeth_of_match);
> +
> +static struct platform_driver liteeth_driver = {
> +	.probe = liteeth_probe,
> +	.remove = liteeth_remove,
> +	.driver = {
> +		.name = DRV_NAME,
> +		.of_match_table = liteeth_of_match,
> +	},
> +};
> +module_platform_driver(liteeth_driver);
> +
> +MODULE_AUTHOR("Joel Stanley <joel@jms.id.au>");
> +MODULE_LICENSE("GPL");
> -- 
> 2.33.0
> 

      reply	other threads:[~2021-08-25 22:04 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-25 12:46 [PATCH v3 0/2] net: Add LiteETH network driver Joel Stanley
2021-08-25 12:46 ` [PATCH v3 1/2] dt-bindings: net: Add bindings for LiteETH Joel Stanley
2021-08-25 16:38   ` Rob Herring
2021-08-25 12:46 ` [PATCH v3 2/2] net: Add driver for LiteX's LiteETH network interface Joel Stanley
2021-08-25 22:04   ` Gabriel L. Somlo [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=YSa+f7yeE4ZGQiuX@errol.ini.cmu.edu \
    --to=gsomlo@gmail.com \
    --cc=dave@ds0.me \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=florent@enjoy-digital.fr \
    --cc=joel@jms.id.au \
    --cc=kgugala@antmicro.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mholenko@antmicro.com \
    --cc=netdev@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=shorne@gmail.com \
    --subject='Re: [PATCH v3 2/2] net: Add driver for LiteX'\''s LiteETH network interface' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).