LKML Archive on lore.kernel.org
help / color / mirror / Atom feed
From: rajpat@codeaurora.org
To: Matthias Kaehlcke <mka@chromium.org>
Cc: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, rnayak@codeaurora.org,
	saiprakash.ranjan@codeaurora.org, msavaliy@qti.qualcomm.com,
	skakit@codeaurora.org, Roja Rani Yarubandi <rojay@codeaurora.org>
Subject: Re: [PATCH V4 2/4] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
Date: Wed, 11 Aug 2021 17:43:48 +0530	[thread overview]
Message-ID: <bdfd39def9a11104c043090d920ef4df@codeaurora.org> (raw)
In-Reply-To: <YP7cmkayoajJ+1yj@google.com>

On 2021-07-26 21:32, Matthias Kaehlcke wrote:
> On Mon, Jul 26, 2021 at 07:10:45PM +0530, Rajesh Patil wrote:
>> From: Roja Rani Yarubandi <rojay@codeaurora.org>
>> 
>> Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.
>> 
>> Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
>> Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
>> ---
>> Changes in V4:
>>  - As per Bjorn's comment, added QUP Wrapper_0 nodes
>>    other than debug-uart node
>>  - Dropped interconnect votes for wrapper_0 node
>> 
>> Changes in V3:
>>  - Broken the huge V2 patch into 3 smaller patches.
>>    1. QSPI DT nodes
>>    2. QUP wrapper_0 DT nodes
>>    3. QUP wrapper_1 DT nodes
>> 
>> Changes in V2:
>>  - As per Doug's comments removed pinmux/pinconf subnodes.
>>  - As per Doug's comments split of SPI, UART nodes has been done.
>>  - Moved QSPI node before aps_smmu as per the order.
>> 
>>  arch/arm64/boot/dts/qcom/sc7280-idp.dts |  84 ++++
>>  arch/arm64/boot/dts/qcom/sc7280.dtsi    | 720 
>> ++++++++++++++++++++++++++++++++
>>  2 files changed, 804 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts 
>> b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
>> index b0bfd8e..f63cf51 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
>> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
>> @@ -358,6 +358,16 @@
>>  	vdda18-supply = <&vreg_l1c_1p8>;
>>  };
>> 
>> +&uart7 {
>> +	status = "okay";
>> +
>> +	/delete-property/interrupts;
>> +	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
>> +				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
>> +	pinctrl-names = "default", "sleep";
>> +	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, 
>> <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
>> +};
>> +
>>  /* PINCTRL - additions to nodes defined in sc7280.dtsi */
>> 
>>  &qspi_cs0 {
>> @@ -428,3 +438,77 @@
>>  		bias-pull-up;
>>  	};
>>  };
>> +&qup_uart7_cts {
>> +	/*
>> +	 * Configure a pull-down on CTS to match the pull of
>> +	 * the Bluetooth module.
>> +	 */
>> +	bias-pull-down;
>> +};
>> +
>> +&qup_uart7_rts {
>> +	/* We'll drive RTS, so no pull */
>> +	drive-strength = <2>;
>> +	bias-disable;
>> +};
>> +
>> +&qup_uart7_tx {
>> +	/* We'll drive TX, so no pull */
>> +	drive-strength = <2>;
>> +	bias-disable;
>> +};
>> +
>> +&qup_uart7_rx {
>> +	/*
>> +	 * Configure a pull-up on RX. This is needed to avoid
>> +	 * garbage data when the TX pin of the Bluetooth module is
>> +	 * in tri-state (module powered off or not driving the
>> +	 * signal yet).
>> +	 */
>> +	bias-pull-up;
>> +};
>> +
>> +&tlmm {
>> +	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
>> +		pins = "gpio28";
>> +		function = "gpio";
>> +		/*
>> +		 * Configure a pull-down on CTS to match the pull of
>> +		 * the Bluetooth module.
>> +		 */
>> +		bias-pull-down;
>> +	};
>> +
>> +	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
>> +		pins = "gpio29";
>> +		function = "gpio";
>> +		/*
>> +		 * Configure pull-down on RTS. As RTS is active low
>> +		 * signal, pull it low to indicate the BT SoC that it
>> +		 * can wakeup the system anytime from suspend state by
>> +		 * pulling RX low (by sending wakeup bytes).
>> +		 */
>> +		bias-pull-down;
>> +	};
>> +
>> +	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
>> +		pins = "gpio30";
>> +		function = "gpio";
>> +		/*
>> +		 * Configure pull-up on TX when it isn't actively driven
>> +		 * to prevent BT SoC from receiving garbage during sleep.
>> +		 */
>> +		bias-pull-up;
>> +	};
>> 
>> +	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
>> +		pins = "gpio31";
>> +		function = "gpio";
>> +		/*
>> +		 * Configure a pull-up on RX. This is needed to avoid
>> +		 * garbage data when the TX pin of the Bluetooth module
>> +		 * is floating which may cause spurious wakeups.
>> +		 */
>> +		bias-pull-up;
>> +	};
>> +};
> 
> How the patches of this series are split strikes me as a bit odd. 
> Supposedly
> this patch adds the QUPv3 wrapper_0 DT nodes for the SC7280, however 
> the
> above is the pin configuration for the Bluetooth UART of the SC7280 IDP 
> board.
> I don't see a good reason why that should be part of this patch. It 
> should be
> a separate change whose subject indicates that it configures the 
> Bluetooth UART
> of the SC7280 IDP.
> 

Okay will split this up.

> Without this conflation of SoC and board DT it would seem perfectly 
> reasonable
> to squash this patch and '[4/4] arm64: dts: sc7280: Add QUPv3 wrapper_1 
> nodes'
> into a single one, they are essentially doing the same thing, I see no 
> need to
> have different patches for the wrapper 0 and 1 nodes.

Previously when QUP wrapper 0 and wrapper 1 nodes were added in single 
patch, we faced some git issues as the patch was huge. Hence we split it 
up.
https://partnerissuetracker.corp.google.com/issues/177045897#comment12

  reply	other threads:[~2021-08-11 12:14 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-07-26 13:40 [PATCH V4 0/4] Add QSPI and QUPv3 DT nodes for SC7280 SoC Rajesh Patil
2021-07-26 13:40 ` [PATCH V4 1/4] arm64: dts: sc7280: Add QSPI node Rajesh Patil
2021-07-26 16:07   ` Matthias Kaehlcke
2021-08-11 12:14     ` rajpat
2021-07-26 13:40 ` [PATCH V4 2/4] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes Rajesh Patil
2021-07-26 16:02   ` Matthias Kaehlcke
2021-08-11 12:13     ` rajpat [this message]
2021-08-11 14:52       ` Matthias Kaehlcke
2021-08-12  7:13         ` rajpat
2021-08-12 12:49           ` Matthias Kaehlcke
2021-07-27 19:20   ` Stephen Boyd
2021-08-11 12:17     ` rajpat
2021-07-26 13:40 ` [PATCH V4 3/4] arm64: dts: sc7280: Update QUPv3 Debug UART DT node Rajesh Patil
2021-07-26 15:42   ` Matthias Kaehlcke
2021-08-11 12:04     ` rajpat
2021-07-26 13:40 ` [PATCH V4 4/4] arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes Rajesh Patil
2021-07-27  0:14 ` [PATCH V4 0/4] Add QSPI and QUPv3 DT nodes for SC7280 SoC Stephen Boyd
2021-08-11 12:14   ` rajpat

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=bdfd39def9a11104c043090d920ef4df@codeaurora.org \
    --to=rajpat@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mka@chromium.org \
    --cc=msavaliy@qti.qualcomm.com \
    --cc=rnayak@codeaurora.org \
    --cc=robh+dt@kernel.org \
    --cc=rojay@codeaurora.org \
    --cc=saiprakash.ranjan@codeaurora.org \
    --cc=skakit@codeaurora.org \
    --subject='Re: [PATCH V4 2/4] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).