Netdev Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Oleksij Rempel <o.rempel@pengutronix.de>
To: alexandru.tachici@analog.com
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, robh+dt@kernel.org, andrew@lunn.ch,
	hkallweit1@gmail.com, linux@armlinux.org.uk, davem@davemloft.net,
	kuba@kernel.org,
	Alexandru Ardelean <alexandru.ardelean@analog.com>
Subject: Re: [PATCH v2 3/7] net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
Date: Tue, 27 Jul 2021 08:47:46 +0200	[thread overview]
Message-ID: <20210727064746.lsz3ip7jyjbjkskj@pengutronix.de> (raw)
In-Reply-To: <20210712130631.38153-4-alexandru.tachici@analog.com>

On Mon, Jul 12, 2021 at 04:06:27PM +0300, alexandru.tachici@analog.com wrote:
> From: Alexandru Ardelean <alexandru.ardelean@analog.com>
> 
> The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
> industrial Ethernet applications and is compliant with the IEEE 802.3cg
> Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
> 
> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
> ---
>  drivers/net/phy/Kconfig    |   7 +
>  drivers/net/phy/Makefile   |   1 +
>  drivers/net/phy/adin1100.c | 326 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 334 insertions(+)
>  create mode 100644 drivers/net/phy/adin1100.c
> 
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index c56f703ae998..8f9f61fe0020 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -83,6 +83,13 @@ config ADIN_PHY
>  	  - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
>  	    Ethernet PHY
>  
> +config ADIN1100_PHY
> +	tristate "Analog Devices Industrial Ethernet T1L PHYs"
> +	help
> +	  Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
> +	  Currently supports the:
> +	  - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
> +
>  config AQUANTIA_PHY
>  	tristate "Aquantia PHYs"
>  	help
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index 172bb193ae6a..3bd6a369d60c 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -31,6 +31,7 @@ sfp-obj-$(CONFIG_SFP)		+= sfp-bus.o
>  obj-y				+= $(sfp-obj-y) $(sfp-obj-m)
>  
>  obj-$(CONFIG_ADIN_PHY)		+= adin.o
> +obj-$(CONFIG_ADIN1100_PHY)	+= adin1100.o
>  obj-$(CONFIG_AMD_PHY)		+= amd.o
>  aquantia-objs			+= aquantia_main.o
>  ifdef CONFIG_HWMON
> diff --git a/drivers/net/phy/adin1100.c b/drivers/net/phy/adin1100.c
> new file mode 100644
> index 000000000000..682fc617c51b
> --- /dev/null
> +++ b/drivers/net/phy/adin1100.c
> @@ -0,0 +1,326 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + *  Driver for Analog Devices Industrial Ethernet T1L PHYs
> + *
> + * Copyright 2020 Analog Devices Inc.
> + */
> +#include <linux/kernel.h>
> +#include <linux/bitfield.h>
> +#include <linux/delay.h>
> +#include <linux/errno.h>
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/mii.h>
> +#include <linux/phy.h>
> +#include <linux/property.h>
> +
> +#define PHY_ID_ADIN1100				0x0283bc81
> +
> +static const int phy_10_features_array[] = {
> +	ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
> +	ETHTOOL_LINK_MODE_1000mv_BIT,
> +};
> +
> +#define ADIN_B10L_PCS_CNTRL			0x08e6
> +#define   ADIN_PCS_CNTRL_B10L_LB_PCS_EN		BIT(14)

This register is "45.2.3.68a 10BASE-T1L PCS control register (Register
3.2278)" according to the 802.3cg-2019.

> +#define ADIN_B10L_PMA_CNTRL			0x08f6
> +#define   ADIN_PMA_CNTRL_B10L_LB_PMA_LOC_EN	BIT(0)
> +
> +#define ADIN_B10L_PMA_STAT			0x08f7
> +#define   ADIN_PMA_STAT_B10L_LB_PMA_LOC_ABLE	BIT(13)
> +#define   ADIN_PMA_STAT_B10L_TX_LVL_HI_ABLE	BIT(12)
> +
> +#define ADIN_AN_CONTROL				0x0200
> +#define   ADIN_AN_RESTART			BIT(9)
> +#define   ADIN_AN_EN				BIT(12)
> +
> +#define ADIN_AN_STATUS				0x0201
> +#define ADIN_AN_ADV_ABILITY_L			0x0202
> +#define ADIN_AN_ADV_ABILITY_M			0x0203
> +#define ADIN_AN_ADV_ABILITY_H			0x0204U
> +#define   ADIN_AN_ADV_B10L_TX_LVL_HI_ABL	BIT(13)
> +#define   ADIN_AN_ADV_B10L_TX_LVL_HI_REQ	BIT(12)

All of this bits are implemented according to the 802.3-2018 standard,
For example ADIN_AN_CONTROL is corresponding to "45.2.7.19 BASE-T1 AN control register (Register 7.512)"

> +
> +#define ADIN_AN_LP_ADV_ABILITY_L		0x0205
> +
> +#define ADIN_AN_LP_ADV_ABILITY_M		0x0206
> +#define   ADIN_AN_LP_ADV_B10L			BIT(14)
> +#define   ADIN_AN_LP_ADV_B1000			BIT(7)
> +#define   ADIN_AN_LP_ADV_B10S_FD		BIT(6)
> +#define   ADIN_AN_LP_ADV_B100			BIT(5)
> +#define   ADIN_AN_LP_ADV_MST			BIT(4)
> +
> +#define ADIN_AN_LP_ADV_ABILITY_H		0x0207
> +#define   ADIN_AN_LP_ADV_B10L_EEE		BIT(14)
> +#define   ADIN_AN_LP_ADV_B10L_TX_LVL_HI_ABL	BIT(13)
> +#define   ADIN_AN_LP_ADV_B10L_TX_LVL_HI_REQ	BIT(12)
> +#define   ADIN_AN_LP_ADV_B10S_HD		BIT(11)

This registers are:
45.2.7.22 BASE-T1 AN LP Base Page ability register (Registers 7.517, 7.518 ..

> +
> +#define ADIN_CRSM_SFT_RST			0x8810
> +#define   ADIN_CRSM_SFT_RST_EN			BIT(0)
> +
> +#define ADIN_CRSM_SFT_PD_CNTRL			0x8812
> +#define   ADIN_CRSM_SFT_PD_CNTRL_EN		BIT(0)
> +
> +#define ADIN_CRSM_STAT				0x8818
> +#define   ADIN_CRSM_SFT_PD_RDY			BIT(1)
> +#define   ADIN_CRSM_SYS_RDY			BIT(0)
> +
> +#define ADIN_MAC_IF_LOOPBACK			0x803d
> +#define   ADIN_MAC_IF_LOOPBACK_EN		BIT(0)
> +#define   ADIN_MAC_IF_REMOTE_LOOPBACK_EN	BIT(2)
> +

Please compare the PHY datasheet with 802.3.2018 and 802.3cg-2019, and
implement common parts as phy generic code.

> +/**
> + * struct adin_priv - ADIN PHY driver private data
> + * tx_level_24v			set if the PHY supports 2.4V TX levels (10BASE-T1L)
> + */
> +struct adin_priv {
> +	unsigned int		tx_level_24v:1;
> +};
> +
> +static void adin_mii_adv_m_to_ethtool_adv_t(unsigned long *advertising, u32 adv)
> +{
> +	if (adv & ADIN_AN_LP_ADV_B10L)
> +		linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, advertising);
> +}
> +
> +static void adin_mii_adv_h_to_ethtool_adv_t(unsigned long *advertising, u32 adv)
> +{
> +	if (adv & ADIN_AN_LP_ADV_B10S_HD)
> +		linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT1L_Half_BIT, advertising);
> +	if (adv & ADIN_AN_LP_ADV_B10L_TX_LVL_HI_ABL)
> +		linkmode_set_bit(ETHTOOL_LINK_MODE_2400mv_BIT, advertising);
> +	if (!(adv & ADIN_AN_LP_ADV_B10L_TX_LVL_HI_REQ))
> +		linkmode_set_bit(ETHTOOL_LINK_MODE_1000mv_BIT, advertising);
> +}
> +
> +static int adin_read_lpa(struct phy_device *phydev)
> +{
> +	int val;
> +
> +	linkmode_zero(phydev->lp_advertising);
> +
> +	val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_STATUS);
> +	if (val < 0)
> +		return val;
> +
> +	if (!(val & MDIO_AN_STAT1_COMPLETE)) {
> +		phydev->pause = 0;
> +		phydev->asym_pause = 0;
> +
> +		return 0;
> +	}
> +
> +	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
> +			 phydev->lp_advertising);
> +
> +	/* Read the link partner's base page advertisement */
> +	val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_L);
> +	if (val < 0)
> +		return val;
> +
> +	phydev->pause = val & LPA_PAUSE_CAP ? 1 : 0;
> +	phydev->asym_pause = val & LPA_PAUSE_ASYM ? 1 : 0;
> +
> +	val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_M);
> +	if (val < 0)
> +		return val;
> +
> +	adin_mii_adv_m_to_ethtool_adv_t(phydev->lp_advertising, val);
> +
> +	val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_H);
> +	if (val < 0)
> +		return val;
> +
> +	adin_mii_adv_h_to_ethtool_adv_t(phydev->lp_advertising, val);
> +
> +	return 0;
> +}
> +
> +static int adin_read_status(struct phy_device *phydev)
> +{
> +	int ret;
> +
> +	ret = genphy_c45_read_link(phydev);
> +	if (ret)
> +		return ret;
> +
> +	phydev->speed = SPEED_UNKNOWN;
> +	phydev->duplex = DUPLEX_UNKNOWN;
> +	phydev->pause = 0;
> +	phydev->asym_pause = 0;
> +
> +	if (phydev->autoneg == AUTONEG_ENABLE) {
> +		ret = adin_read_lpa(phydev);
> +		if (ret)
> +			return ret;
> +
> +		phy_resolve_aneg_linkmode(phydev);
> +	} else {
> +		/* Only one mode & duplex supported */
> +		linkmode_zero(phydev->lp_advertising);
> +		phydev->speed = SPEED_10;
> +		phydev->duplex = DUPLEX_FULL;
> +	}
> +
> +	return ret;
> +}
> +
> +static int adin_config_aneg(struct phy_device *phydev)
> +{
> +	struct adin_priv *priv = phydev->priv;
> +	int ret;
> +
> +	/* No sense to continue if auto-neg is disabled,
> +	 * only one link-mode supported.
> +	 */
> +	if (phydev->autoneg == AUTONEG_DISABLE)
> +		return 0;
> +
> +	if (priv->tx_level_24v)
> +		ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN,
> +				       ADIN_AN_ADV_ABILITY_H,
> +				       ADIN_AN_ADV_B10L_TX_LVL_HI_ABL |
> +				       ADIN_AN_ADV_B10L_TX_LVL_HI_REQ);
> +	else
> +		ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN,
> +					 ADIN_AN_ADV_ABILITY_H,
> +					 ADIN_AN_ADV_B10L_TX_LVL_HI_ABL |
> +					 ADIN_AN_ADV_B10L_TX_LVL_HI_REQ);
> +
> +	if (ret < 0)
> +		return ret;
> +
> +	return phy_set_bits_mmd(phydev, MDIO_MMD_AN, ADIN_AN_CONTROL, ADIN_AN_RESTART);
> +}
> +
> +static int adin_set_powerdown_mode(struct phy_device *phydev, bool en)
> +{
> +	int ret;
> +	int val;
> +
> +	if (en)
> +		val = ADIN_CRSM_SFT_PD_CNTRL_EN;
> +	else
> +		val = 0;
> +
> +	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
> +			    ADIN_CRSM_SFT_PD_CNTRL, val);
> +	if (ret < 0)
> +		return ret;
> +
> +	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
> +					 (ret & ADIN_CRSM_SFT_PD_RDY) == val,
> +					 1000, 30000, true);
> +}
> +
> +static int adin_suspend(struct phy_device *phydev)
> +{
> +	return adin_set_powerdown_mode(phydev, true);
> +}
> +
> +static int adin_resume(struct phy_device *phydev)
> +{
> +	return adin_set_powerdown_mode(phydev, false);
> +}
> +
> +static int adin_set_loopback(struct phy_device *phydev, bool enable)
> +{
> +	if (enable)
> +		return phy_set_bits_mmd(phydev, MDIO_MMD_PCS, ADIN_B10L_PCS_CNTRL,
> +					ADIN_PCS_CNTRL_B10L_LB_PCS_EN);
> +
> +	/* PCS loopback (according to 10BASE-T1L spec) */
> +	return phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, ADIN_B10L_PCS_CNTRL,
> +				 ADIN_PCS_CNTRL_B10L_LB_PCS_EN);
> +}
> +
> +static int adin_soft_reset(struct phy_device *phydev)
> +{
> +	int ret;
> +
> +	ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN_CRSM_SFT_RST, ADIN_CRSM_SFT_RST_EN);
> +	if (ret < 0)
> +		return ret;
> +
> +	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
> +					 (ret & ADIN_CRSM_SYS_RDY),
> +					 10000, 30000, true);
> +}
> +
> +static int adin_get_features(struct phy_device *phydev)
> +{
> +	struct adin_priv *priv = phydev->priv;
> +	struct device *dev = &phydev->mdio.dev;
> +	int ret;
> +
> +	ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, ADIN_B10L_PMA_STAT);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* This depends on the voltage level from the power source */
> +	priv->tx_level_24v = !!(ret & ADIN_PMA_STAT_B10L_TX_LVL_HI_ABLE);
> +
> +	phydev_dbg(phydev, "PHY supports 2.4V TX level: %s\n",
> +		   priv->tx_level_24v ? "yes" : "no");
> +
> +	if (device_property_present(dev, "adi,disable-2400mv-tx-level")) {
> +		if (priv->tx_level_24v)
> +			phydev_info(phydev,
> +				    "PHY supports 2.4V TX level, but disabled via config\n");
> +
> +		priv->tx_level_24v = 0;
> +	}
> +
> +	if (priv->tx_level_24v)
> +		linkmode_set_bit(ETHTOOL_LINK_MODE_2400mv_BIT, phydev->supported);
> +
> +	linkmode_set_bit_array(phy_basic_ports_array, ARRAY_SIZE(phy_basic_ports_array),
> +			       phydev->supported);
> +
> +	linkmode_set_bit_array(phy_10_features_array, ARRAY_SIZE(phy_10_features_array),
> +			       phydev->supported);
> +
> +	return 0;
> +}
> +
> +static int adin_probe(struct phy_device *phydev)
> +{
> +	struct device *dev = &phydev->mdio.dev;
> +	struct adin_priv *priv;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	phydev->priv = priv;
> +
> +	return 0;
> +}
> +
> +static struct phy_driver adin_driver[] = {
> +	{
> +		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100),
> +		.name			= "ADIN1100",
> +		.get_features		= adin_get_features,
> +		.soft_reset		= adin_soft_reset,
> +		.probe			= adin_probe,
> +		.config_aneg		= adin_config_aneg,
> +		.read_status		= adin_read_status,
> +		.set_loopback		= adin_set_loopback,
> +		.suspend		= adin_suspend,
> +		.resume			= adin_resume,
> +	},
> +};
> +
> +module_phy_driver(adin_driver);
> +
> +static struct mdio_device_id __maybe_unused adin_tbl[] = {
> +	{ PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100) },
> +	{ }
> +};
> +
> +MODULE_DEVICE_TABLE(mdio, adin_tbl);
> +MODULE_DESCRIPTION("Analog Devices Industrial Ethernet T1L PHY driver");
> +MODULE_LICENSE("Dual BSD/GPL");
> -- 
> 2.25.1
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

  parent reply	other threads:[~2021-07-27  6:47 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-07-12 13:06 [PATCH v2 0/7] " alexandru.tachici
2021-07-12 13:06 ` [PATCH v2 1/7] ethtool: Add 10base-T1L link mode entries alexandru.tachici
2021-07-13 16:50   ` Andrew Lunn
2021-07-27  5:56   ` Oleksij Rempel
2021-07-12 13:06 ` [PATCH v2 2/7] ethtool: Add 10base-T1L voltage levels " alexandru.tachici
2021-07-12 13:06 ` [PATCH v2 3/7] net: phy: adin1100: Add initial support for ADIN1100 industrial PHY alexandru.tachici
2021-07-13 16:58   ` Andrew Lunn
2021-07-16 21:24     ` ADIN1100 alexandru.tachici
2021-07-23 17:20       ` ADIN1100 Oleksij Rempel
2021-07-27  6:31     ` [PATCH v2 3/7] net: phy: adin1100: Add initial support for ADIN1100 industrial PHY Oleksij Rempel
2021-07-27  6:47   ` Oleksij Rempel [this message]
2021-07-27 16:36     ` Andrew Lunn
2021-07-12 13:06 ` [PATCH v2 4/7] net: phy: adin1100: Add ethtool get_stats support alexandru.tachici
2021-07-12 18:41   ` Jakub Kicinski
2021-07-12 13:06 ` [PATCH v2 5/7] net: phy: adin1100: Add ethtool master-slave support alexandru.tachici
2021-07-13 17:53   ` Andrew Lunn
2021-07-12 13:06 ` [PATCH v2 6/7] net: phy: adin1100: Add SQI support alexandru.tachici
2021-07-13 17:55   ` Andrew Lunn
2021-07-12 13:06 ` [PATCH v2 7/7] dt-bindings: adin1100: Add binding for ADIN1100 Ethernet PHY alexandru.tachici
2021-07-12 14:12   ` Rob Herring
2021-07-12 17:46     ` Rob Herring
2021-07-27  5:53   ` Oleksij Rempel
2021-07-28 17:23     ` Rob Herring
2021-07-29  5:02       ` Oleksij Rempel
2021-07-12 13:33 ` [PATCH v2 0/7] net: phy: adin1100: Add initial support for ADIN1100 industrial PHY Russell King (Oracle)
2021-07-23 17:32   ` Oleksij Rempel
2021-08-03  9:47     ` alexandru.tachici
2021-08-03 11:59       ` Oleksij Rempel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210727064746.lsz3ip7jyjbjkskj@pengutronix.de \
    --to=o.rempel@pengutronix.de \
    --cc=alexandru.ardelean@analog.com \
    --cc=alexandru.tachici@analog.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=hkallweit1@gmail.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --subject='Re: [PATCH v2 3/7] net: phy: adin1100: Add initial support for ADIN1100 industrial PHY' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).