Netdev Archive on lore.kernel.org
help / color / mirror / Atom feed
From: Dario Alcocer <dalcocer@helixd.com>
To: netdev@vger.kernel.org
Subject: Marvell switch port shows LOWERLAYERDOWN, ping fails
Date: Thu, 22 Jul 2021 15:55:04 -0700	[thread overview]
Message-ID: <6a70869d-d8d5-4647-0640-4e95866a0392@helixd.com> (raw)

After configuring a DSA tree for two Marvell 88E6176 chips, attempts to
ping a host connected to the first user port fail. Running "ip link" shows
the user port state as LOWERLAYERDOWN, and no packets make it out the port.

It's not clear why the state is LOWERLAYERDOWN. The port has a connected
network device, and the port LED is on.

I'd welcome any ideas on how to figure out why the port is not working.

The Marvell chips are configured for multi-chip mode, and are connected
to a single MDIO bus:

* chip at PHY address 0x1E is connected to eth0 of the host processor,
   an Altera Cyclone V
* chip at PHY address 0x1A is connected over SERDES to the other chip,
   using port 4

Here's a console capture showing the port set-up and the failed ping:

root@dali:~# uname -a
Linux dali 5.4.114-altera #1 SMP Thu Jul 22 20:07:57 UTC 2021 armv7l armv7l armv7l GNU/Linux
root@dali:~# ip link

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
     link/can
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1508 qdisc mq state UP mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/sit 0.0.0.0 brd 0.0.0.0
5: lan1@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
6: lan2@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
7: lan3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
8: lan4@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
9: dmz@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
root@dali:~# ip addr add 192.0.2.1/24 dev lan1
root@dali:~# ip link set lan1 up
[  902.623835] mv88e6085 stmmac-0:1a lan1: configuring for phy/gmii link mode
[  902.633092] 8021q: adding VLAN 0 to HW filter on device lan1
root@dali:~# ping -c 4 192.0.2.2
PING 192.0.2.2 (192.0.2.2): 56 data bytes

--- 192.0.2.2 ping statistics ---
4 packets transmitted, 0 packets received, 100% packet loss
root@dali:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
     link/can
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1508 qdisc mq state UP mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/sit 0.0.0.0 brd 0.0.0.0
5: lan1@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
6: lan2@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
7: lan3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
8: lan4@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
9: dmz@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
     link/ether aa:10:22:58:38:77 brd ff:ff:ff:ff:ff:ff
root@dali:~# ip route
default via 192.168.0.1 dev eth0
192.0.2.0/24 dev lan1 proto kernel scope link src 192.0.2.1 linkdown
192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.3
224.0.0.0/4 dev eth0 scope link src 192.168.0.3
root@dali:~#

The DSA switch tree is configured using this device tree fragment:

gmac0 {
     status = "okay";
     phy-mode = "gmii";
     txc-skew-ps = <0xbb8>;
     rxc-skew-ps = <0xbb8>;
     txen-skew-ps = <0>;
     rxdv-skew-ps = <0>;
     rxd0-skew-ps = <0>;
     rxd1-skew-ps = <0>;
     rxd2-skew-ps = <0>;
     rxd3-skew-ps = <0>;
     txd0-skew-ps = <0>;
     txd1-skew-ps = <0>;
     txd2-skew-ps = <0>;
     txd3-skew-ps = <0>;
     max-frame-size = <3800>;

     fixed-link {
     speed = <0x3e8>;
         full-duplex;
         pause;
     };

     mdio {
         compatible = "snps,dwmac-mdio";
         #address-cells = <0x1>;
         #size-cells = <0x0>;

         switch0: switch0@1a {
             compatible = "marvell,mv88e6085";
             reg = <0x1a>;
             dsa,member = <0 0>;
             ports {
                 #address-cells = <1>;
                 #size-cells = <0>;
                 port@0 {
                     reg = <0>;
                     label = "lan1";
                 };
                 port@1 {
                     reg = <1>;
                     label = "lan2";
                 };
                 port@2 {
                     reg = <2>;
                     label = "lan3";
                 };
                 switch0port4: port@4 {
                     reg = <4>;
                     phy-mode = "rgmii-id";
                     link = <&switch1port4>;
                     fixed-link {
                         speed = <1000>;
                         full-duplex;
                     };
                 };
                 port@6 {
                     reg = <6>;
                     ethernet = <&gmac0>;
                     label = "cpu";
                 };
             };
         };
         switch1: switch1@1e {
             compatible = "marvell,mv88e6085";
             reg = <0x1e>;
             dsa,member = <0 1>;
             ports {
                 #address-cells = <1>;
                 #size-cells = <0>;
                 port@0 {
                     reg = <0>;
                     label = "lan4";
                 };
                 port@1 {
                     reg = <1>;
                     label = "dmz";
                 };
                 switch1port4: port@4 {
                     reg = <4>;
                     link = <&switch0port4>;
                     phy-mode = "rgmii-id";
                     fixed-link {
                         speed = <1000>;
                         full-duplex;
                     };
                 };
             };
         };
     };
};


             reply	other threads:[~2021-07-22 23:03 UTC|newest]

Thread overview: 27+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-07-22 22:55 Dario Alcocer [this message]
2021-07-23 13:41 ` Andrew Lunn
2021-07-23 18:21   ` Dario Alcocer
2021-07-23 18:25     ` Andrew Lunn
2021-07-23 18:36       ` Dario Alcocer
2021-07-23 21:58         ` Dario Alcocer
2021-07-24 17:34           ` Andrew Lunn
2021-07-25  2:26             ` Dario Alcocer
2021-07-25  2:36               ` Dario Alcocer
2021-07-27  1:39                 ` Dario Alcocer
2021-07-28 18:07                   ` Dario Alcocer
2021-07-28 18:23                     ` Andrew Lunn
2021-07-28 18:33                       ` Dario Alcocer
2021-07-28 19:24                         ` Andrew Lunn
2021-07-28 19:37                           ` Dario Alcocer
2021-07-28 20:47                             ` Andrew Lunn
2021-07-28 20:54                               ` Dario Alcocer
2021-07-28 21:09                             ` Andrew Lunn
2021-08-05 21:44                             ` Dario Alcocer
2021-08-06 16:03                               ` Dario Alcocer
2021-08-06 23:46                                 ` Dario Alcocer
2021-08-07 18:57                                   ` Andrew Lunn
2021-08-09 16:28                                     ` Dario Alcocer
2021-08-10 20:58                                       ` Dario Alcocer
2021-08-10 22:13                                         ` Andrew Lunn
2021-08-11 13:16                                           ` Dario Alcocer
2021-08-07 17:44                               ` Andrew Lunn

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6a70869d-d8d5-4647-0640-4e95866a0392@helixd.com \
    --to=dalcocer@helixd.com \
    --cc=netdev@vger.kernel.org \
    --subject='Re: Marvell switch port shows LOWERLAYERDOWN, ping fails' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).